linux-omap.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org>
To: linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org,
	linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org,
	Felipe Balbi <balbi-l0cyMroinI0@public.gmane.org>,
	Tony Lindgren <tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org>
Cc: Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org>
Subject: [PATCH v2 4/5] USB: OMAP1: Tahvo USB transceiver driver
Date: Sun, 16 Jun 2013 16:35:11 +0300	[thread overview]
Message-ID: <1371389712-29516-5-git-send-email-aaro.koskinen@iki.fi> (raw)
In-Reply-To: <1371389712-29516-1-git-send-email-aaro.koskinen-X3B1VOXEql0@public.gmane.org>

Add Tahvo USB transceiver driver.

Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.

Signed-off-by: Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org>
---
 drivers/usb/phy/Kconfig     |  14 ++
 drivers/usb/phy/Makefile    |   1 +
 drivers/usb/phy/phy-tahvo.c | 448 ++++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 463 insertions(+)
 create mode 100644 drivers/usb/phy/phy-tahvo.c

diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 14a50bd..a5c7937 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -145,6 +145,20 @@ config OMAP_OTG
 	  This driver can also be built as a module. If so, the module
 	  will be called omap-otg.
 
+config TAHVO_USB
+	tristate "Tahvo USB transceiver driver"
+	depends on MFD_RETU && EXTCON
+	help
+	  Enable this to support USB transceiver on Tahvo. This is used
+	  at least on Nokia 770.
+
+config TAHVO_USB_HOST_BY_DEFAULT
+	depends on TAHVO_USB
+	boolean "Device in USB host mode by default"
+	help
+	  Say Y here, if you want the device to enter USB host mode
+	  by default on bootup.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index c7f391b..f3984d1 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -13,6 +13,7 @@ phy-fsl-usb2-objs			:= phy-fsl-usb.o phy-fsm-usb.o
 obj-$(CONFIG_FSL_USB2_OTG)		+= phy-fsl-usb2.o
 obj-$(CONFIG_ISP1301_OMAP)		+= phy-isp1301-omap.o
 obj-$(CONFIG_MV_U3D_PHY)		+= phy-mv-u3d-usb.o
+obj-$(CONFIG_TAHVO_USB)			+= phy-tahvo.o
 obj-$(CONFIG_NOP_USB_XCEIV)		+= phy-nop.o
 obj-$(CONFIG_OMAP_CONTROL_USB)		+= phy-omap-control.o
 obj-$(CONFIG_OMAP_OTG)			+= phy-omap-otg.o
diff --git a/drivers/usb/phy/phy-tahvo.c b/drivers/usb/phy/phy-tahvo.c
new file mode 100644
index 0000000..a2d96a2
--- /dev/null
+++ b/drivers/usb/phy/phy-tahvo.c
@@ -0,0 +1,448 @@
+/*
+ * Tahvo USB transceiver driver
+ *
+ * Copyright (C) 2005-2006 Nokia Corporation
+ *
+ * Parts copied from isp1301_omap.c.
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2004 David Brownell
+ *
+ * Original driver written by Juha Yrjölä, Tony Lindgren and Timo Teräs.
+ * Modified for Retu/Tahvo MFD by Aaro Koskinen.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/usb.h>
+#include <linux/extcon.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/usb/otg.h>
+#include <linux/mfd/retu.h>
+#include <linux/usb/gadget.h>
+#include <linux/platform_device.h>
+
+#define DRIVER_NAME     "tahvo-usb"
+
+#define TAHVO_REG_IDSR	0x02
+#define TAHVO_REG_USBR	0x06
+
+#define USBR_SLAVE_CONTROL	(1 << 8)
+#define USBR_VPPVIO_SW		(1 << 7)
+#define USBR_SPEED		(1 << 6)
+#define USBR_REGOUT		(1 << 5)
+#define USBR_MASTER_SW2		(1 << 4)
+#define USBR_MASTER_SW1		(1 << 3)
+#define USBR_SLAVE_SW		(1 << 2)
+#define USBR_NSUSPEND		(1 << 1)
+#define USBR_SEMODE		(1 << 0)
+
+#define TAHVO_MODE_HOST		0
+#define TAHVO_MODE_PERIPHERAL	1
+
+struct tahvo_usb {
+	struct platform_device	*pt_dev;
+	struct usb_phy		phy;
+	int			vbus_state;
+	struct mutex		serialize;
+	struct clk		*ick;
+	int			irq;
+	int			tahvo_mode;
+	struct extcon_dev	extcon;
+};
+
+static const char *tahvo_cable[] = {
+	"USB-HOST",
+	"USB",
+	NULL,
+};
+
+static ssize_t vbus_state_show(struct device *device,
+			       struct device_attribute *attr, char *buf)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+	return sprintf(buf, "%d\n", tu->vbus_state);
+}
+static DEVICE_ATTR(vbus_state, 0444, vbus_state_show, NULL);
+
+static void check_vbus_state(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+	int reg, prev_state;
+
+	reg = retu_read(rdev, TAHVO_REG_IDSR);
+	if (reg & TAHVO_STAT_VBUS) {
+		switch (tu->phy.state) {
+		case OTG_STATE_B_IDLE:
+			/* Enable the gadget driver */
+			if (tu->phy.otg->gadget)
+				usb_gadget_vbus_connect(tu->phy.otg->gadget);
+			tu->phy.state = OTG_STATE_B_PERIPHERAL;
+			break;
+		case OTG_STATE_A_IDLE:
+			/*
+			 * Session is now valid assuming the USB hub is driving
+			 * Vbus.
+			 */
+			tu->phy.state = OTG_STATE_A_HOST;
+			break;
+		default:
+			break;
+		}
+		dev_info(&tu->pt_dev->dev, "USB cable connected\n");
+	} else {
+		switch (tu->phy.state) {
+		case OTG_STATE_B_PERIPHERAL:
+			if (tu->phy.otg->gadget)
+				usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+			tu->phy.state = OTG_STATE_B_IDLE;
+			break;
+		case OTG_STATE_A_HOST:
+			tu->phy.state = OTG_STATE_A_IDLE;
+			break;
+		default:
+			break;
+		}
+		dev_info(&tu->pt_dev->dev, "USB cable disconnected\n");
+	}
+
+	prev_state = tu->vbus_state;
+	tu->vbus_state = reg & TAHVO_STAT_VBUS;
+	if (prev_state != tu->vbus_state) {
+		extcon_set_cable_state(&tu->extcon, "USB", tu->vbus_state);
+		sysfs_notify(&tu->pt_dev->dev.kobj, NULL, "vbus_state");
+	}
+}
+
+static void tahvo_usb_become_host(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	extcon_set_cable_state(&tu->extcon, "USB-HOST", true);
+
+	/* Power up the transceiver in USB host mode */
+	retu_write(rdev, TAHVO_REG_USBR, USBR_REGOUT | USBR_NSUSPEND |
+		   USBR_MASTER_SW2 | USBR_MASTER_SW1);
+	tu->phy.state = OTG_STATE_A_IDLE;
+
+	check_vbus_state(tu);
+}
+
+static void tahvo_usb_stop_host(struct tahvo_usb *tu)
+{
+	tu->phy.state = OTG_STATE_A_IDLE;
+}
+
+static void tahvo_usb_become_peripheral(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	extcon_set_cable_state(&tu->extcon, "USB-HOST", false);
+
+	/* Power up transceiver and set it in USB peripheral mode */
+	retu_write(rdev, TAHVO_REG_USBR, USBR_SLAVE_CONTROL | USBR_REGOUT |
+		   USBR_NSUSPEND | USBR_SLAVE_SW);
+	tu->phy.state = OTG_STATE_B_IDLE;
+
+	check_vbus_state(tu);
+}
+
+static void tahvo_usb_stop_peripheral(struct tahvo_usb *tu)
+{
+	if (tu->phy.otg->gadget)
+		usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+	tu->phy.state = OTG_STATE_B_IDLE;
+}
+
+static void tahvo_usb_power_off(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	/* Disable gadget controller if any */
+	if (tu->phy.otg->gadget)
+		usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+
+	/* Power off transceiver */
+	retu_write(rdev, TAHVO_REG_USBR, 0);
+	tu->phy.state = OTG_STATE_UNDEFINED;
+}
+
+static int tahvo_usb_set_suspend(struct usb_phy *dev, int suspend)
+{
+	struct tahvo_usb *tu = container_of(dev, struct tahvo_usb, phy);
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+	u16 w;
+
+	dev_dbg(&tu->pt_dev->dev, "%s\n", __func__);
+
+	w = retu_read(rdev, TAHVO_REG_USBR);
+	if (suspend)
+		w &= ~USBR_NSUSPEND;
+	else
+		w |= USBR_NSUSPEND;
+	retu_write(rdev, TAHVO_REG_USBR, w);
+
+	return 0;
+}
+
+static int tahvo_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	struct tahvo_usb *tu = container_of(otg->phy, struct tahvo_usb, phy);
+
+	dev_dbg(&tu->pt_dev->dev, "%s %p\n", __func__, host);
+
+	if (otg == NULL)
+		return -ENODEV;
+
+	mutex_lock(&tu->serialize);
+
+	if (host == NULL) {
+		if (tu->tahvo_mode == TAHVO_MODE_HOST)
+			tahvo_usb_power_off(tu);
+		otg->host = NULL;
+		mutex_unlock(&tu->serialize);
+		return 0;
+	}
+
+	if (tu->tahvo_mode == TAHVO_MODE_HOST) {
+		otg->host = NULL;
+		tahvo_usb_become_host(tu);
+	}
+
+	otg->host = host;
+
+	mutex_unlock(&tu->serialize);
+
+	return 0;
+}
+
+static int tahvo_usb_set_peripheral(struct usb_otg *otg,
+				    struct usb_gadget *gadget)
+{
+	struct tahvo_usb *tu = container_of(otg->phy, struct tahvo_usb, phy);
+
+	dev_dbg(&tu->pt_dev->dev, "%s %p\n", __func__, gadget);
+
+	if (!otg)
+		return -ENODEV;
+
+	mutex_lock(&tu->serialize);
+
+	if (!gadget) {
+		if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+			tahvo_usb_power_off(tu);
+		tu->phy.otg->gadget = NULL;
+		mutex_unlock(&tu->serialize);
+		return 0;
+	}
+
+	tu->phy.otg->gadget = gadget;
+	if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+		tahvo_usb_become_peripheral(tu);
+
+	mutex_unlock(&tu->serialize);
+
+	return 0;
+}
+
+static irqreturn_t tahvo_usb_vbus_interrupt(int irq, void *_tu)
+{
+	struct tahvo_usb *tu = _tu;
+
+	mutex_lock(&tu->serialize);
+	check_vbus_state(tu);
+	mutex_unlock(&tu->serialize);
+
+	return IRQ_HANDLED;
+}
+
+static ssize_t otg_mode_show(struct device *device,
+			     struct device_attribute *attr, char *buf)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+
+	switch (tu->tahvo_mode) {
+	case TAHVO_MODE_HOST:
+		return sprintf(buf, "host\n");
+	case TAHVO_MODE_PERIPHERAL:
+		return sprintf(buf, "peripheral\n");
+	}
+
+	return -EINVAL;
+}
+
+static ssize_t otg_mode_store(struct device *device,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+	int r;
+
+	mutex_lock(&tu->serialize);
+	if (count >= 4 && strncmp(buf, "host", 4) == 0) {
+		if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+			tahvo_usb_stop_peripheral(tu);
+		tu->tahvo_mode = TAHVO_MODE_HOST;
+		if (tu->phy.otg->host) {
+			dev_info(device, "HOST mode: host controller present\n");
+			tahvo_usb_become_host(tu);
+		} else {
+			dev_info(device, "HOST mode: no host controller, powering off\n");
+			tahvo_usb_power_off(tu);
+		}
+		r = strlen(buf);
+	} else if (count >= 10 && strncmp(buf, "peripheral", 10) == 0) {
+		if (tu->tahvo_mode == TAHVO_MODE_HOST)
+			tahvo_usb_stop_host(tu);
+		tu->tahvo_mode = TAHVO_MODE_PERIPHERAL;
+		if (tu->phy.otg->gadget) {
+			dev_info(device, "PERIPHERAL mode: gadget driver present\n");
+			tahvo_usb_become_peripheral(tu);
+		} else {
+			dev_info(device, "PERIPHERAL mode: no gadget driver, powering off\n");
+			tahvo_usb_power_off(tu);
+		}
+		r = strlen(buf);
+	} else {
+		r = -EINVAL;
+	}
+	mutex_unlock(&tu->serialize);
+
+	return r;
+}
+
+static DEVICE_ATTR(otg_mode, 0644, otg_mode_show, otg_mode_store);
+
+static int tahvo_usb_probe(struct platform_device *pdev)
+{
+	struct retu_dev *rdev = dev_get_drvdata(pdev->dev.parent);
+	struct tahvo_usb *tu;
+	int ret;
+
+	tu = devm_kzalloc(&pdev->dev, sizeof(*tu), GFP_KERNEL);
+	if (!tu)
+		return -ENOMEM;
+
+	tu->phy.otg = devm_kzalloc(&pdev->dev, sizeof(*tu->phy.otg),
+				   GFP_KERNEL);
+	if (!tu->phy.otg)
+		return -ENOMEM;
+
+	tu->pt_dev = pdev;
+
+	/* Default mode */
+#ifdef CONFIG_TAHVO_USB_HOST_BY_DEFAULT
+	tu->tahvo_mode = TAHVO_MODE_HOST;
+#else
+	tu->tahvo_mode = TAHVO_MODE_PERIPHERAL;
+#endif
+
+	mutex_init(&tu->serialize);
+
+	tu->ick = devm_clk_get(&pdev->dev, "usb_l4_ick");
+	if (!IS_ERR(tu->ick))
+		clk_enable(tu->ick);
+
+	/*
+	 * Set initial state, so that we generate kevents only on state changes.
+	 */
+	tu->vbus_state = retu_read(rdev, TAHVO_REG_IDSR) & TAHVO_STAT_VBUS;
+
+	tu->extcon.name = DRIVER_NAME;
+	tu->extcon.supported_cable = tahvo_cable;
+	ret = extcon_dev_register(&tu->extcon, &pdev->dev);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register extcon device: %d\n",
+			ret);
+		return ret;
+	}
+
+	/* Set the initial cable state. */
+	extcon_set_cable_state(&tu->extcon, "USB-HOST",
+			       tu->tahvo_mode == TAHVO_MODE_HOST);
+	extcon_set_cable_state(&tu->extcon, "USB", tu->vbus_state);
+
+	tu->irq = platform_get_irq(pdev, 0);
+	ret = request_threaded_irq(tu->irq, NULL, tahvo_usb_vbus_interrupt, 0,
+				   "tahvo-vbus", tu);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register tahvo-vbus irq: %d\n",
+			ret);
+		goto err_disable_clk;
+	}
+
+	/* Attributes */
+	ret = device_create_file(&pdev->dev, &dev_attr_vbus_state);
+	ret |= device_create_file(&pdev->dev, &dev_attr_otg_mode);
+	if (ret)
+		dev_err(&pdev->dev, "attribute creation failed: %d\n", ret);
+
+	/* Create OTG interface */
+	tahvo_usb_power_off(tu);
+	tu->phy.dev = &pdev->dev;
+	tu->phy.state = OTG_STATE_UNDEFINED;
+	tu->phy.label = DRIVER_NAME;
+	tu->phy.set_suspend = tahvo_usb_set_suspend;
+
+	tu->phy.otg->phy = &tu->phy;
+	tu->phy.otg->set_host = tahvo_usb_set_host;
+	tu->phy.otg->set_peripheral = tahvo_usb_set_peripheral;
+
+	ret = usb_add_phy(&tu->phy, USB_PHY_TYPE_USB2);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "cannot register USB transceiver: %d\n",
+			ret);
+		goto err_free_irq;
+	}
+
+	dev_set_drvdata(&pdev->dev, tu);
+
+	return 0;
+
+err_free_irq:
+	free_irq(tu->irq, tu);
+err_disable_clk:
+	if (!IS_ERR(tu->ick))
+		clk_disable(tu->ick);
+
+	return ret;
+}
+
+static int tahvo_usb_remove(struct platform_device *pdev)
+{
+	struct tahvo_usb *tu = platform_get_drvdata(pdev);
+
+	free_irq(tu->irq, tu);
+	usb_remove_phy(&tu->phy);
+	device_remove_file(&pdev->dev, &dev_attr_vbus_state);
+	device_remove_file(&pdev->dev, &dev_attr_otg_mode);
+	extcon_dev_unregister(&tu->extcon);
+	if (!IS_ERR(tu->ick))
+		clk_disable(tu->ick);
+
+	return 0;
+}
+
+static struct platform_driver tahvo_usb_driver = {
+	.probe		= tahvo_usb_probe,
+	.remove		= tahvo_usb_remove,
+	.driver		= {
+		.name	= "tahvo-usb",
+		.owner	= THIS_MODULE,
+	},
+};
+module_platform_driver(tahvo_usb_driver);
+
+MODULE_DESCRIPTION("Tahvo USB transceiver driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Juha Yrjölä, Tony Lindgren, and Timo Teräs");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen-X3B1VOXEql0@public.gmane.org>");
-- 
1.8.3.1

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

  parent reply	other threads:[~2013-06-16 13:35 UTC|newest]

Thread overview: 10+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2013-06-16 13:35 [PATCH v2 0/5] USB: OMAP1: Tahvo USB support for 770 Aaro Koskinen
     [not found] ` <1371389712-29516-1-git-send-email-aaro.koskinen-X3B1VOXEql0@public.gmane.org>
2013-06-16 13:35   ` [PATCH v2 1/5] ARM: OMAP1: USB: move omap_usb_config to platform data Aaro Koskinen
     [not found]     ` <1371389712-29516-2-git-send-email-aaro.koskinen-X3B1VOXEql0@public.gmane.org>
2013-06-18 10:01       ` Tony Lindgren
2013-06-16 13:35   ` [PATCH v2 3/5] USB: OMAP1: OTG controller driver Aaro Koskinen
2013-06-18  8:21     ` Felipe Balbi
2013-06-18 16:55       ` Aaro Koskinen
2013-06-16 13:35   ` Aaro Koskinen [this message]
2013-06-16 13:35 ` [PATCH v2 2/5] USB: OMAP1: add extcon to platform data Aaro Koskinen
2013-06-16 13:35 ` [PATCH v2 5/5] ARM: OMAP1: nokia770: enable Tahvo Aaro Koskinen
     [not found]   ` <1371389712-29516-6-git-send-email-aaro.koskinen-X3B1VOXEql0@public.gmane.org>
2013-06-18 10:16     ` Tony Lindgren

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=1371389712-29516-5-git-send-email-aaro.koskinen@iki.fi \
    --to=aaro.koskinen-x3b1voxeql0@public.gmane.org \
    --cc=balbi-l0cyMroinI0@public.gmane.org \
    --cc=linux-arm-kernel-IAPFreCvJWM7uuMidbF8XUB+6BGkLq7r@public.gmane.org \
    --cc=linux-omap-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=linux-usb-u79uwXL29TY76Z2rM5mHXA@public.gmane.org \
    --cc=tony-4v6yS6AI5VpBDgjK7y7TUQ@public.gmane.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).