[PATCH 0/3] USB: OMAP: Tahvo USB support for 770

[PATCH 0/3] USB: OMAP: Tahvo USB support for 770

[Aaro Koskinen]

Hi,

These patches add support for Tahvo USB transceiver and allow using both
host and peripheral modes on Nokia 770.

Tested (peripheral mode, host mode, vbus detection) with 3.10-rc4.

Aaro Koskinen (3):
  ARM: OMAP1: nokia770: enable Tahvo
  USB: OMAP: add omap-otg
  USB: OMAP: Tahvo USB transceiver driver

 arch/arm/mach-omap1/board-nokia770.c |   10 +
 drivers/usb/phy/Kconfig              |   24 ++
 drivers/usb/phy/Makefile             |    2 +
 drivers/usb/phy/phy-omap-otg.c       |  126 ++++++++++
 drivers/usb/phy/phy-tahvo.c          |  429 ++++++++++++++++++++++++++++++++++
 include/linux/usb/omap-otg.h         |   19 ++
 6 files changed, 610 insertions(+)
 create mode 100644 drivers/usb/phy/phy-omap-otg.c
 create mode 100644 drivers/usb/phy/phy-tahvo.c
 create mode 100644 include/linux/usb/omap-otg.h

-- 
1.7.10.4

--
To unsubscribe from this list: send the line "unsubscribe linux-usb" in
the body of a message to majordomo-u79uwXL29TY76Z2rM5mHXA@public.gmane.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/3] ARM: OMAP1: nokia770: enable Tahvo

[Aaro Koskinen]

Add platform data for Tahvo.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
---
 arch/arm/mach-omap1/board-nokia770.c |   10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm/mach-omap1/board-nokia770.c b/arch/arm/mach-omap1/board-nokia770.c
index 62a15e2..91449c5 100644
--- a/arch/arm/mach-omap1/board-nokia770.c
+++ b/arch/arm/mach-omap1/board-nokia770.c
@@ -234,16 +234,26 @@ static struct i2c_board_info nokia770_i2c_board_info_2[] __initdata = {
 	{
 		I2C_BOARD_INFO("retu-mfd", 0x01),
 	},
+	{
+		I2C_BOARD_INFO("tahvo-mfd", 0x02),
+	},
 };
 
 static void __init nokia770_cbus_init(void)
 {
 	const int retu_irq_gpio = 62;
+	const int tahvo_irq_gpio = 40;
 
 	if (gpio_request_one(retu_irq_gpio, GPIOF_IN, "Retu IRQ"))
 		return;
+	if (gpio_request_one(tahvo_irq_gpio, GPIOF_IN, "Tahvo IRQ")) {
+		gpio_free(retu_irq_gpio);
+		return;
+	}
 	irq_set_irq_type(gpio_to_irq(retu_irq_gpio), IRQ_TYPE_EDGE_RISING);
+	irq_set_irq_type(gpio_to_irq(tahvo_irq_gpio), IRQ_TYPE_EDGE_RISING);
 	nokia770_i2c_board_info_2[0].irq = gpio_to_irq(retu_irq_gpio);
+	nokia770_i2c_board_info_2[1].irq = gpio_to_irq(tahvo_irq_gpio);
 	i2c_register_board_info(2, nokia770_i2c_board_info_2,
 				ARRAY_SIZE(nokia770_i2c_board_info_2));
 	platform_device_register(&nokia770_cbus_device);
-- 
1.7.10.4

[PATCH 2/3] USB: OMAP: add omap-otg

[Aaro Koskinen]

Transceivers need to manage OTG controller state on OMAP1 to enable
switching between peripheral and host modes. Provide a driver for that.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
---
 drivers/usb/phy/Kconfig        |   10 ++++
 drivers/usb/phy/Makefile       |    1 +
 drivers/usb/phy/phy-omap-otg.c |  126 ++++++++++++++++++++++++++++++++++++++++
 include/linux/usb/omap-otg.h   |   19 ++++++
 4 files changed, 156 insertions(+)
 create mode 100644 drivers/usb/phy/phy-omap-otg.c
 create mode 100644 include/linux/usb/omap-otg.h

diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 7ef3eb8..2d2cd5f 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -135,6 +135,16 @@ config USB_GPIO_VBUS
 	  optionally control of a D+ pullup GPIO as well as a VBUS
 	  current limit regulator.
 
+config OMAP_OTG
+	tristate "OMAP USB OTG controller driver"
+	depends on ARCH_OMAP_OTG
+	help
+	  Enable this to support some transceivers on OMAP1 platforms. OTG
+	  controller is needed to switch between host and peripheral modes.
+
+	  This driver can also be built as a module. If so, the module
+	  will be called omap-otg.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index a9169cb..c7f391b 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -15,6 +15,7 @@ obj-$(CONFIG_ISP1301_OMAP)		+= phy-isp1301-omap.o
 obj-$(CONFIG_MV_U3D_PHY)		+= phy-mv-u3d-usb.o
 obj-$(CONFIG_NOP_USB_XCEIV)		+= phy-nop.o
 obj-$(CONFIG_OMAP_CONTROL_USB)		+= phy-omap-control.o
+obj-$(CONFIG_OMAP_OTG)			+= phy-omap-otg.o
 obj-$(CONFIG_OMAP_USB2)			+= phy-omap-usb2.o
 obj-$(CONFIG_OMAP_USB3)			+= phy-omap-usb3.o
 obj-$(CONFIG_SAMSUNG_USBPHY)		+= phy-samsung-usb.o
diff --git a/drivers/usb/phy/phy-omap-otg.c b/drivers/usb/phy/phy-omap-otg.c
new file mode 100644
index 0000000..cb00ffe
--- /dev/null
+++ b/drivers/usb/phy/phy-omap-otg.c
@@ -0,0 +1,126 @@
+/*
+ * OMAP OTG controller driver
+ *
+ * Based on code from tahvo-usb.c and isp1301_omap.c drivers.
+ *
+ * Copyright (C) 2005-2006 Nokia Corporation
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2004 David Brownell
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/err.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/usb/omap-otg.h>
+#include <linux/platform_device.h>
+
+struct otg_device {
+	void __iomem	*base;
+	struct mutex	serialize;
+};
+static struct otg_device *otg_dev;
+
+#define OMAP_OTG_CTRL		(otg_dev->base + 0x0c)
+#define OMAP_OTG_ASESSVLD	(1 << 20)
+#define OMAP_OTG_BSESSEND	(1 << 19)
+#define OMAP_OTG_BSESSVLD	(1 << 18)
+#define OMAP_OTG_VBUSVLD	(1 << 17)
+#define OMAP_OTG_ID		(1 << 16)
+#define OMAP_OTG_XCEIV_OUTPUTS \
+	(OMAP_OTG_ASESSVLD | OMAP_OTG_BSESSEND | OMAP_OTG_BSESSVLD | \
+	 OMAP_OTG_VBUSVLD  | OMAP_OTG_ID)
+
+static void omap_otg_ctrl(u32 outputs)
+{
+	u32 l;
+
+	l = readl(OMAP_OTG_CTRL);
+	l &= ~OMAP_OTG_XCEIV_OUTPUTS;
+	l |= outputs;
+	writel(l, OMAP_OTG_CTRL);
+}
+
+void omap_otg_set_mode(enum omap_otg_mode mode)
+{
+	if (!otg_dev) {
+		WARN(1, "%s: controller not present\n", __func__);
+		return;
+	}
+	mutex_lock(&otg_dev->serialize);
+	switch (mode) {
+	case OMAP_OTG_MODE_DEVICE:
+		/*
+		 * Set B-session valid.
+		 */
+		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSVLD);
+		break;
+	case OMAP_OTG_MODE_HOST:
+		/*
+		 * Set A-session valid.
+		 */
+		omap_otg_ctrl(OMAP_OTG_ASESSVLD);
+		break;
+	case OMAP_OTG_MODE_DISCONNECT:
+		/*
+		 * Set B-session end to indicate no VBUS.
+		 */
+		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSEND);
+		break;
+	default:
+		WARN(1, "%s: unknown mode: %d\n", __func__, mode);
+	}
+	mutex_unlock(&otg_dev->serialize);
+}
+EXPORT_SYMBOL_GPL(omap_otg_set_mode);
+
+static int omap_otg_probe(struct platform_device *dev)
+{
+	struct otg_device *odev;
+	u32 rev;
+
+	if (otg_dev)
+		return -EBUSY;
+
+	odev = devm_kzalloc(&dev->dev, sizeof(*odev), GFP_KERNEL);
+	if (!odev)
+		return -ENOMEM;
+
+	odev->base = devm_ioremap_resource(&dev->dev, &dev->resource[0]);
+	if (IS_ERR(odev->base))
+		return PTR_ERR(odev->base);
+
+	rev = readl(odev->base);
+	dev_info(&dev->dev, "OMAP USB OTG controller rev %d.%d\n",
+		 (rev >> 4) & 0xf, rev & 0xf);
+
+	mutex_init(&odev->serialize);
+
+	otg_dev = odev;
+
+	return 0;
+}
+
+static struct platform_driver omap_otg_driver = {
+	.probe		= omap_otg_probe,
+	.driver		= {
+		.owner	= THIS_MODULE,
+		.name	= "omap_otg",
+	},
+};
+module_platform_driver(omap_otg_driver);
+
+MODULE_DESCRIPTION("OMAP USB OTG controller driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
diff --git a/include/linux/usb/omap-otg.h b/include/linux/usb/omap-otg.h
new file mode 100644
index 0000000..fb3d7ab
--- /dev/null
+++ b/include/linux/usb/omap-otg.h
@@ -0,0 +1,19 @@
+/*
+ * OMAP OTG driver
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License. See the file "COPYING" in the main directory of this archive for
+ * more details.
+ */
+#ifndef __LINUX_OMAP_OTG_H
+#define __LINUX_OMAP_OTG_H
+
+enum omap_otg_mode {
+	OMAP_OTG_MODE_DEVICE,
+	OMAP_OTG_MODE_HOST,
+	OMAP_OTG_MODE_DISCONNECT,
+};
+
+void omap_otg_set_mode(enum omap_otg_mode mode);
+
+#endif /* __LINUX_OMAP_OTG_H */
-- 
1.7.10.4

[PATCH 3/3] USB: OMAP: Tahvo USB transceiver driver

[Aaro Koskinen]

Add Tahvo USB transceiver driver.

Based on old code from linux-omap tree. The original driver was written
by Juha Yrjölä, Tony Lindgren, and Timo Teräs.

Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
---
 drivers/usb/phy/Kconfig     |   14 ++
 drivers/usb/phy/Makefile    |    1 +
 drivers/usb/phy/phy-tahvo.c |  429 +++++++++++++++++++++++++++++++++++++++++++
 3 files changed, 444 insertions(+)
 create mode 100644 drivers/usb/phy/phy-tahvo.c

diff --git a/drivers/usb/phy/Kconfig b/drivers/usb/phy/Kconfig
index 2d2cd5f..f796745 100644
--- a/drivers/usb/phy/Kconfig
+++ b/drivers/usb/phy/Kconfig
@@ -145,6 +145,20 @@ config OMAP_OTG
 	  This driver can also be built as a module. If so, the module
 	  will be called omap-otg.
 
+config TAHVO_USB
+	tristate "Tahvo USB transceiver driver"
+	depends on MFD_RETU && OMAP_OTG
+	help
+	  Enable this to support USB transceiver on Tahvo. This is used
+	  at least on Nokia 770.
+
+config TAHVO_USB_HOST_BY_DEFAULT
+	depends on TAHVO_USB
+	boolean "Device in USB host mode by default"
+	help
+	  Say Y here, if you want the device to enter USB host mode
+	  by default on bootup.
+
 config USB_ISP1301
 	tristate "NXP ISP1301 USB transceiver support"
 	depends on USB || USB_GADGET
diff --git a/drivers/usb/phy/Makefile b/drivers/usb/phy/Makefile
index c7f391b..f3984d1 100644
--- a/drivers/usb/phy/Makefile
+++ b/drivers/usb/phy/Makefile
@@ -13,6 +13,7 @@ phy-fsl-usb2-objs			:= phy-fsl-usb.o phy-fsm-usb.o
 obj-$(CONFIG_FSL_USB2_OTG)		+= phy-fsl-usb2.o
 obj-$(CONFIG_ISP1301_OMAP)		+= phy-isp1301-omap.o
 obj-$(CONFIG_MV_U3D_PHY)		+= phy-mv-u3d-usb.o
+obj-$(CONFIG_TAHVO_USB)			+= phy-tahvo.o
 obj-$(CONFIG_NOP_USB_XCEIV)		+= phy-nop.o
 obj-$(CONFIG_OMAP_CONTROL_USB)		+= phy-omap-control.o
 obj-$(CONFIG_OMAP_OTG)			+= phy-omap-otg.o
diff --git a/drivers/usb/phy/phy-tahvo.c b/drivers/usb/phy/phy-tahvo.c
new file mode 100644
index 0000000..51bc40e
--- /dev/null
+++ b/drivers/usb/phy/phy-tahvo.c
@@ -0,0 +1,429 @@
+/*
+ * Tahvo USB transceiver driver
+ *
+ * Copyright (C) 2005-2006 Nokia Corporation
+ *
+ * Parts copied from isp1301_omap.c.
+ * Copyright (C) 2004 Texas Instruments
+ * Copyright (C) 2004 David Brownell
+ *
+ * Original driver written by Juha Yrjölä, Tony Lindgren and Timo Teräs.
+ * Modified for Retu/Tahvo MFD by Aaro Koskinen.
+ *
+ * This file is subject to the terms and conditions of the GNU General
+ * Public License. See the file "COPYING" in the main directory of this
+ * archive for more details.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ */
+
+#include <linux/io.h>
+#include <linux/clk.h>
+#include <linux/usb.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/usb/otg.h>
+#include <linux/mfd/retu.h>
+#include <linux/usb/gadget.h>
+#include <linux/usb/omap-otg.h>
+#include <linux/platform_device.h>
+
+#define DRIVER_NAME     "tahvo-usb"
+
+#define TAHVO_REG_IDSR	0x02
+#define TAHVO_REG_USBR	0x06
+
+#define USBR_SLAVE_CONTROL	(1 << 8)
+#define USBR_VPPVIO_SW		(1 << 7)
+#define USBR_SPEED		(1 << 6)
+#define USBR_REGOUT		(1 << 5)
+#define USBR_MASTER_SW2		(1 << 4)
+#define USBR_MASTER_SW1		(1 << 3)
+#define USBR_SLAVE_SW		(1 << 2)
+#define USBR_NSUSPEND		(1 << 1)
+#define USBR_SEMODE		(1 << 0)
+
+#define TAHVO_MODE_HOST		0
+#define TAHVO_MODE_PERIPHERAL	1
+
+struct tahvo_usb {
+	struct platform_device	*pt_dev;
+	struct usb_phy		phy;
+	int			vbus_state;
+	struct mutex		serialize;
+	struct clk		*ick;
+	int			irq;
+	int			tahvo_mode;
+};
+
+static ssize_t vbus_state_show(struct device *device,
+			       struct device_attribute *attr, char *buf)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+	return sprintf(buf, "%d\n", tu->vbus_state);
+}
+static DEVICE_ATTR(vbus_state, 0444, vbus_state_show, NULL);
+
+static void check_vbus_state(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+	int reg, prev_state;
+
+	reg = retu_read(rdev, TAHVO_REG_IDSR);
+	if (reg & TAHVO_STAT_VBUS) {
+		switch (tu->phy.state) {
+		case OTG_STATE_B_IDLE:
+			/* Enable the gadget driver */
+			if (tu->phy.otg->gadget)
+				usb_gadget_vbus_connect(tu->phy.otg->gadget);
+			omap_otg_set_mode(OMAP_OTG_MODE_DEVICE);
+			tu->phy.state = OTG_STATE_B_PERIPHERAL;
+			break;
+		case OTG_STATE_A_IDLE:
+			/*
+			 * Session is now valid assuming the USB hub is driving
+			 * Vbus.
+			 */
+			tu->phy.state = OTG_STATE_A_HOST;
+			break;
+		default:
+			break;
+		}
+		dev_info(&tu->pt_dev->dev, "USB cable connected\n");
+	} else {
+		switch (tu->phy.state) {
+		case OTG_STATE_B_PERIPHERAL:
+			if (tu->phy.otg->gadget)
+				usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+			tu->phy.state = OTG_STATE_B_IDLE;
+			break;
+		case OTG_STATE_A_HOST:
+			tu->phy.state = OTG_STATE_A_IDLE;
+			break;
+		default:
+			break;
+		}
+		dev_info(&tu->pt_dev->dev, "USB cable disconnected\n");
+	}
+
+	prev_state = tu->vbus_state;
+	tu->vbus_state = reg & TAHVO_STAT_VBUS;
+	if (prev_state != tu->vbus_state)
+		sysfs_notify(&tu->pt_dev->dev.kobj, NULL, "vbus_state");
+}
+
+static void tahvo_usb_become_host(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	omap_otg_set_mode(OMAP_OTG_MODE_HOST);
+
+	/* Power up the transceiver in USB host mode */
+	retu_write(rdev, TAHVO_REG_USBR, USBR_REGOUT | USBR_NSUSPEND |
+		   USBR_MASTER_SW2 | USBR_MASTER_SW1);
+	tu->phy.state = OTG_STATE_A_IDLE;
+
+	check_vbus_state(tu);
+}
+
+static void tahvo_usb_stop_host(struct tahvo_usb *tu)
+{
+	tu->phy.state = OTG_STATE_A_IDLE;
+}
+
+static void tahvo_usb_become_peripheral(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	omap_otg_set_mode(OMAP_OTG_MODE_DISCONNECT);
+
+	/* Power up transceiver and set it in USB peripheral mode */
+	retu_write(rdev, TAHVO_REG_USBR, USBR_SLAVE_CONTROL | USBR_REGOUT |
+		   USBR_NSUSPEND | USBR_SLAVE_SW);
+	tu->phy.state = OTG_STATE_B_IDLE;
+
+	check_vbus_state(tu);
+}
+
+static void tahvo_usb_stop_peripheral(struct tahvo_usb *tu)
+{
+	omap_otg_set_mode(OMAP_OTG_MODE_DISCONNECT);
+	if (tu->phy.otg->gadget)
+		usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+	tu->phy.state = OTG_STATE_B_IDLE;
+}
+
+static void tahvo_usb_power_off(struct tahvo_usb *tu)
+{
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+
+	/* Disable gadget controller if any */
+	if (tu->phy.otg->gadget)
+		usb_gadget_vbus_disconnect(tu->phy.otg->gadget);
+
+	if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+		omap_otg_set_mode(OMAP_OTG_MODE_DISCONNECT);
+
+	/* Power off transceiver */
+	retu_write(rdev, TAHVO_REG_USBR, 0);
+	tu->phy.state = OTG_STATE_UNDEFINED;
+}
+
+static int tahvo_usb_set_suspend(struct usb_phy *dev, int suspend)
+{
+	struct tahvo_usb *tu = container_of(dev, struct tahvo_usb, phy);
+	struct retu_dev *rdev = dev_get_drvdata(tu->pt_dev->dev.parent);
+	u16 w;
+
+	dev_dbg(&tu->pt_dev->dev, "%s\n", __func__);
+
+	w = retu_read(rdev, TAHVO_REG_USBR);
+	if (suspend)
+		w &= ~USBR_NSUSPEND;
+	else
+		w |= USBR_NSUSPEND;
+	retu_write(rdev, TAHVO_REG_USBR, w);
+
+	return 0;
+}
+
+static int tahvo_usb_set_host(struct usb_otg *otg, struct usb_bus *host)
+{
+	struct tahvo_usb *tu = container_of(otg->phy, struct tahvo_usb, phy);
+
+	dev_dbg(&tu->pt_dev->dev, "%s %p\n", __func__, host);
+
+	if (otg == NULL)
+		return -ENODEV;
+
+	mutex_lock(&tu->serialize);
+
+	if (host == NULL) {
+		if (tu->tahvo_mode == TAHVO_MODE_HOST)
+			tahvo_usb_power_off(tu);
+		otg->host = NULL;
+		mutex_unlock(&tu->serialize);
+		return 0;
+	}
+
+	if (tu->tahvo_mode == TAHVO_MODE_HOST) {
+		otg->host = NULL;
+		tahvo_usb_become_host(tu);
+	}
+
+	otg->host = host;
+
+	mutex_unlock(&tu->serialize);
+
+	return 0;
+}
+
+static int tahvo_usb_set_peripheral(struct usb_otg *otg,
+				    struct usb_gadget *gadget)
+{
+	struct tahvo_usb *tu = container_of(otg->phy, struct tahvo_usb, phy);
+
+	dev_dbg(&tu->pt_dev->dev, "%s %p\n", __func__, gadget);
+
+	if (!otg)
+		return -ENODEV;
+
+	mutex_lock(&tu->serialize);
+
+	if (!gadget) {
+		if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+			tahvo_usb_power_off(tu);
+		tu->phy.otg->gadget = NULL;
+		mutex_unlock(&tu->serialize);
+		return 0;
+	}
+
+	tu->phy.otg->gadget = gadget;
+	if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+		tahvo_usb_become_peripheral(tu);
+
+	mutex_unlock(&tu->serialize);
+
+	return 0;
+}
+
+static irqreturn_t tahvo_usb_vbus_interrupt(int irq, void *_tu)
+{
+	struct tahvo_usb *tu = _tu;
+
+	mutex_lock(&tu->serialize);
+	check_vbus_state(tu);
+	mutex_unlock(&tu->serialize);
+
+	return IRQ_HANDLED;
+}
+
+static ssize_t otg_mode_show(struct device *device,
+			     struct device_attribute *attr, char *buf)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+
+	switch (tu->tahvo_mode) {
+	case TAHVO_MODE_HOST:
+		return sprintf(buf, "host\n");
+	case TAHVO_MODE_PERIPHERAL:
+		return sprintf(buf, "peripheral\n");
+	}
+
+	return -EINVAL;
+}
+
+static ssize_t otg_mode_store(struct device *device,
+			      struct device_attribute *attr,
+			      const char *buf, size_t count)
+{
+	struct tahvo_usb *tu = dev_get_drvdata(device);
+	int r;
+
+	mutex_lock(&tu->serialize);
+	if (count >= 4 && strncmp(buf, "host", 4) == 0) {
+		if (tu->tahvo_mode == TAHVO_MODE_PERIPHERAL)
+			tahvo_usb_stop_peripheral(tu);
+		tu->tahvo_mode = TAHVO_MODE_HOST;
+		if (tu->phy.otg->host) {
+			dev_info(device, "HOST mode: host controller present\n");
+			tahvo_usb_become_host(tu);
+		} else {
+			dev_info(device, "HOST mode: no host controller, powering off\n");
+			tahvo_usb_power_off(tu);
+		}
+		r = strlen(buf);
+	} else if (count >= 10 && strncmp(buf, "peripheral", 10) == 0) {
+		if (tu->tahvo_mode == TAHVO_MODE_HOST)
+			tahvo_usb_stop_host(tu);
+		tu->tahvo_mode = TAHVO_MODE_PERIPHERAL;
+		if (tu->phy.otg->gadget) {
+			dev_info(device, "PERIPHERAL mode: gadget driver present\n");
+			tahvo_usb_become_peripheral(tu);
+		} else {
+			dev_info(device, "PERIPHERAL mode: no gadget driver, powering off\n");
+			tahvo_usb_power_off(tu);
+		}
+		r = strlen(buf);
+	} else {
+		r = -EINVAL;
+	}
+	mutex_unlock(&tu->serialize);
+
+	return r;
+}
+
+static DEVICE_ATTR(otg_mode, 0644, otg_mode_show, otg_mode_store);
+
+static int tahvo_usb_probe(struct platform_device *pdev)
+{
+	struct retu_dev *rdev = dev_get_drvdata(pdev->dev.parent);
+	struct tahvo_usb *tu;
+	int ret;
+
+	tu = devm_kzalloc(&pdev->dev, sizeof(*tu), GFP_KERNEL);
+	if (!tu)
+		return -ENOMEM;
+
+	tu->phy.otg = devm_kzalloc(&pdev->dev, sizeof(*tu->phy.otg),
+				   GFP_KERNEL);
+	if (!tu->phy.otg)
+		return -ENOMEM;
+
+	tu->pt_dev = pdev;
+
+	/* Default mode */
+#ifdef CONFIG_TAHVO_USB_HOST_BY_DEFAULT
+	tu->tahvo_mode = TAHVO_MODE_HOST;
+#else
+	tu->tahvo_mode = TAHVO_MODE_PERIPHERAL;
+#endif
+
+	mutex_init(&tu->serialize);
+
+	tu->ick = devm_clk_get(&pdev->dev, "usb_l4_ick");
+	if (!IS_ERR(tu->ick))
+		clk_enable(tu->ick);
+
+	/*
+	 * Set initial state, so that we generate kevents only on state changes.
+	 */
+	tu->vbus_state = retu_read(rdev, TAHVO_REG_IDSR) & TAHVO_STAT_VBUS;
+
+	tu->irq = platform_get_irq(pdev, 0);
+	ret = request_threaded_irq(tu->irq, NULL, tahvo_usb_vbus_interrupt, 0,
+				   "tahvo-vbus", tu);
+	if (ret) {
+		dev_err(&pdev->dev, "could not register tahvo-vbus irq: %d\n",
+			ret);
+		goto err_disable_clk;
+	}
+
+	/* Attributes */
+	ret = device_create_file(&pdev->dev, &dev_attr_vbus_state);
+	ret |= device_create_file(&pdev->dev, &dev_attr_otg_mode);
+	if (ret)
+		dev_err(&pdev->dev, "attribute creation failed: %d\n", ret);
+
+	/* Create OTG interface */
+	tahvo_usb_power_off(tu);
+	tu->phy.dev = &pdev->dev;
+	tu->phy.state = OTG_STATE_UNDEFINED;
+	tu->phy.label = DRIVER_NAME;
+	tu->phy.set_suspend = tahvo_usb_set_suspend;
+
+	tu->phy.otg->phy = &tu->phy;
+	tu->phy.otg->set_host = tahvo_usb_set_host;
+	tu->phy.otg->set_peripheral = tahvo_usb_set_peripheral;
+
+	ret = usb_add_phy(&tu->phy, USB_PHY_TYPE_USB2);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "cannot register USB transceiver: %d\n",
+			ret);
+		goto err_free_irq;
+	}
+
+	dev_set_drvdata(&pdev->dev, tu);
+
+	return 0;
+
+err_free_irq:
+	free_irq(tu->irq, tu);
+err_disable_clk:
+	if (!IS_ERR(tu->ick))
+		clk_disable(tu->ick);
+
+	return ret;
+}
+
+static int tahvo_usb_remove(struct platform_device *pdev)
+{
+	struct tahvo_usb *tu = platform_get_drvdata(pdev);
+
+	free_irq(tu->irq, tu);
+	usb_remove_phy(&tu->phy);
+	device_remove_file(&pdev->dev, &dev_attr_vbus_state);
+	device_remove_file(&pdev->dev, &dev_attr_otg_mode);
+	if (!IS_ERR(tu->ick))
+		clk_disable(tu->ick);
+
+	return 0;
+}
+
+static struct platform_driver tahvo_usb_driver = {
+	.probe		= tahvo_usb_probe,
+	.remove		= tahvo_usb_remove,
+	.driver		= {
+		.name	= "tahvo-usb",
+		.owner	= THIS_MODULE,
+	},
+};
+module_platform_driver(tahvo_usb_driver);
+
+MODULE_DESCRIPTION("Tahvo USB transceiver driver");
+MODULE_LICENSE("GPL");
+MODULE_AUTHOR("Juha Yrjölä, Tony Lindgren, and Timo Teräs");
+MODULE_AUTHOR("Aaro Koskinen <aaro.koskinen@iki.fi>");
-- 
1.7.10.4

--
To unsubscribe from this list: send the line "unsubscribe linux-omap" in
the body of a message to majordomo@vger.kernel.org
More majordomo info at  http://vger.kernel.org/majordomo-info.html

Re: [PATCH 2/3] USB: OMAP: add omap-otg

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 985 bytes --]

Hi,

On Mon, Jun 10, 2013 at 01:40:05AM +0300, Aaro Koskinen wrote:
> +void omap_otg_set_mode(enum omap_otg_mode mode)
> +{
> +	if (!otg_dev) {
> +		WARN(1, "%s: controller not present\n", __func__);
> +		return;
> +	}
> +	mutex_lock(&otg_dev->serialize);
> +	switch (mode) {
> +	case OMAP_OTG_MODE_DEVICE:
> +		/*
> +		 * Set B-session valid.
> +		 */
> +		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSVLD);
> +		break;
> +	case OMAP_OTG_MODE_HOST:
> +		/*
> +		 * Set A-session valid.
> +		 */
> +		omap_otg_ctrl(OMAP_OTG_ASESSVLD);
> +		break;
> +	case OMAP_OTG_MODE_DISCONNECT:
> +		/*
> +		 * Set B-session end to indicate no VBUS.
> +		 */
> +		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSEND);
> +		break;
> +	default:
> +		WARN(1, "%s: unknown mode: %d\n", __func__, mode);
> +	}
> +	mutex_unlock(&otg_dev->serialize);
> +}
> +EXPORT_SYMBOL_GPL(omap_otg_set_mode);

looks like this should provide a extcon interface for its users.

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]

Re: [PATCH 2/3] USB: OMAP: add omap-otg

[Aaro Koskinen]

Hi,

On Wed, Jun 12, 2013 at 06:13:26PM +0300, Felipe Balbi wrote:
> On Mon, Jun 10, 2013 at 01:40:05AM +0300, Aaro Koskinen wrote:
> > +void omap_otg_set_mode(enum omap_otg_mode mode)
> > +{
> > +	if (!otg_dev) {
> > +		WARN(1, "%s: controller not present\n", __func__);
> > +		return;
> > +	}
> > +	mutex_lock(&otg_dev->serialize);
> > +	switch (mode) {
> > +	case OMAP_OTG_MODE_DEVICE:
> > +		/*
> > +		 * Set B-session valid.
> > +		 */
> > +		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSVLD);
> > +		break;
> > +	case OMAP_OTG_MODE_HOST:
> > +		/*
> > +		 * Set A-session valid.
> > +		 */
> > +		omap_otg_ctrl(OMAP_OTG_ASESSVLD);
> > +		break;
> > +	case OMAP_OTG_MODE_DISCONNECT:
> > +		/*
> > +		 * Set B-session end to indicate no VBUS.
> > +		 */
> > +		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSEND);
> > +		break;
> > +	default:
> > +		WARN(1, "%s: unknown mode: %d\n", __func__, mode);
> > +	}
> > +	mutex_unlock(&otg_dev->serialize);
> > +}
> > +EXPORT_SYMBOL_GPL(omap_otg_set_mode);
> 
> looks like this should provide a extcon interface for its users.

Is there any examples available? Anyway, I'll look into this.

Thanks,

A.

Re: [PATCH 2/3] USB: OMAP: add omap-otg

[Felipe Balbi]

[-- Attachment #1: Type: text/plain, Size: 1419 bytes --]

Hi,

On Fri, Jun 14, 2013 at 01:37:11AM +0300, Aaro Koskinen wrote:
> Hi,
> 
> On Wed, Jun 12, 2013 at 06:13:26PM +0300, Felipe Balbi wrote:
> > On Mon, Jun 10, 2013 at 01:40:05AM +0300, Aaro Koskinen wrote:
> > > +void omap_otg_set_mode(enum omap_otg_mode mode)
> > > +{
> > > +	if (!otg_dev) {
> > > +		WARN(1, "%s: controller not present\n", __func__);
> > > +		return;
> > > +	}
> > > +	mutex_lock(&otg_dev->serialize);
> > > +	switch (mode) {
> > > +	case OMAP_OTG_MODE_DEVICE:
> > > +		/*
> > > +		 * Set B-session valid.
> > > +		 */
> > > +		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSVLD);
> > > +		break;
> > > +	case OMAP_OTG_MODE_HOST:
> > > +		/*
> > > +		 * Set A-session valid.
> > > +		 */
> > > +		omap_otg_ctrl(OMAP_OTG_ASESSVLD);
> > > +		break;
> > > +	case OMAP_OTG_MODE_DISCONNECT:
> > > +		/*
> > > +		 * Set B-session end to indicate no VBUS.
> > > +		 */
> > > +		omap_otg_ctrl(OMAP_OTG_ID | OMAP_OTG_BSESSEND);
> > > +		break;
> > > +	default:
> > > +		WARN(1, "%s: unknown mode: %d\n", __func__, mode);
> > > +	}
> > > +	mutex_unlock(&otg_dev->serialize);
> > > +}
> > > +EXPORT_SYMBOL_GPL(omap_otg_set_mode);
> > 
> > looks like this should provide a extcon interface for its users.
> 
> Is there any examples available? Anyway, I'll look into this.

In extcon tree there are some patches from Kishon adding that to
dwc3-omap.c :-)

-- 
balbi

[-- Attachment #2: Digital signature --]
[-- Type: application/pgp-signature, Size: 836 bytes --]