[PATCH AUTOSEL 5.6 01/79] ARM: dts: OMAP3: disable RNG on N950/N9

[PATCH AUTOSEL 5.6 01/79] ARM: dts: OMAP3: disable RNG on N950/N9

[Sasha Levin]

From: Aaro Koskinen <aaro.koskinen@iki.fi>

[ Upstream commit 07bdc492cff6f555538df95e9812fe72e16d154a ]

Like on N900, we cannot access RNG directly on N950/N9. Mark it disabled in
the DTS to allow kernel to boot.

Fixes: 308607e5545f ("ARM: dts: Configure omap3 rng")
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 arch/arm/boot/dts/omap3-n950-n9.dtsi | 5 +++++
 1 file changed, 5 insertions(+)

diff --git a/arch/arm/boot/dts/omap3-n950-n9.dtsi b/arch/arm/boot/dts/omap3-n950-n9.dtsi
index a075b63f3087d..11d41e86f814d 100644
--- a/arch/arm/boot/dts/omap3-n950-n9.dtsi
+++ b/arch/arm/boot/dts/omap3-n950-n9.dtsi
@@ -341,6 +341,11 @@
 	status = "disabled";
 };
 
+/* RNG not directly accessible on N950/N9. */
+&rng_target {
+	status = "disabled";
+};
+
 &usb_otg_hs {
 	interface-type = <0>;
 	usb-phy = <&usb2_phy>;
-- 
2.20.1

[PATCH AUTOSEL 5.6 27/79] usb: dwc3: gadget: Properly set maxpacket limit

[Sasha Levin]

From: Thinh Nguyen <Thinh.Nguyen@synopsys.com>

[ Upstream commit d94ea5319813658ad5861d161ae16a194c2abf88 ]

Currently the calculation of max packet size limit for IN endpoints is
too restrictive. This prevents a matching of a capable hardware endpoint
during configuration. Below is the minimum recommended HW configuration
to support a particular endpoint setup from the databook:

For OUT endpoints, the databook recommended the minimum RxFIFO size to
be at least 3x MaxPacketSize + 3x setup packets size (8 bytes each) +
clock crossing margin (16 bytes).

For IN endpoints, the databook recommended the minimum TxFIFO size to be
at least 3x MaxPacketSize for endpoints that support burst. If the
endpoint doesn't support burst or when the device is operating in USB
2.0 mode, a minimum TxFIFO size of 2x MaxPacketSize is recommended.

Base on these recommendations, we can calculate the MaxPacketSize limit
of each endpoint. This patch revises the IN endpoint MaxPacketSize limit
and also sets the MaxPacketSize limit for OUT endpoints.

Reference: Databook 3.30a section 3.2.2 and 3.2.3

Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/dwc3/core.h   |  4 +++
 drivers/usb/dwc3/gadget.c | 52 ++++++++++++++++++++++++++++++---------
 2 files changed, 45 insertions(+), 11 deletions(-)

diff --git a/drivers/usb/dwc3/core.h b/drivers/usb/dwc3/core.h
index 3ecc69c5b150f..ce4acbf7fef90 100644
--- a/drivers/usb/dwc3/core.h
+++ b/drivers/usb/dwc3/core.h
@@ -310,6 +310,10 @@
 #define DWC3_GTXFIFOSIZ_TXFDEF(n)	((n) & 0xffff)
 #define DWC3_GTXFIFOSIZ_TXFSTADDR(n)	((n) & 0xffff0000)
 
+/* Global RX Fifo Size Register */
+#define DWC31_GRXFIFOSIZ_RXFDEP(n)	((n) & 0x7fff)	/* DWC_usb31 only */
+#define DWC3_GRXFIFOSIZ_RXFDEP(n)	((n) & 0xffff)
+
 /* Global Event Size Registers */
 #define DWC3_GEVNTSIZ_INTMASK		BIT(31)
 #define DWC3_GEVNTSIZ_SIZE(n)		((n) & 0xffff)
diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 9460d42f86757..1e68c90a83781 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -2227,7 +2227,6 @@ static int dwc3_gadget_init_in_endpoint(struct dwc3_ep *dep)
 {
 	struct dwc3 *dwc = dep->dwc;
 	int mdwidth;
-	int kbytes;
 	int size;
 
 	mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);
@@ -2243,17 +2242,17 @@ static int dwc3_gadget_init_in_endpoint(struct dwc3_ep *dep)
 	/* FIFO Depth is in MDWDITH bytes. Multiply */
 	size *= mdwidth;
 
-	kbytes = size / 1024;
-	if (kbytes == 0)
-		kbytes = 1;
-
 	/*
-	 * FIFO sizes account an extra MDWIDTH * (kbytes + 1) bytes for
-	 * internal overhead. We don't really know how these are used,
-	 * but documentation say it exists.
+	 * To meet performance requirement, a minimum TxFIFO size of 3x
+	 * MaxPacketSize is recommended for endpoints that support burst and a
+	 * minimum TxFIFO size of 2x MaxPacketSize for endpoints that don't
+	 * support burst. Use those numbers and we can calculate the max packet
+	 * limit as below.
 	 */
-	size -= mdwidth * (kbytes + 1);
-	size /= kbytes;
+	if (dwc->maximum_speed >= USB_SPEED_SUPER)
+		size /= 3;
+	else
+		size /= 2;
 
 	usb_ep_set_maxpacket_limit(&dep->endpoint, size);
 
@@ -2271,8 +2270,39 @@ static int dwc3_gadget_init_in_endpoint(struct dwc3_ep *dep)
 static int dwc3_gadget_init_out_endpoint(struct dwc3_ep *dep)
 {
 	struct dwc3 *dwc = dep->dwc;
+	int mdwidth;
+	int size;
+
+	mdwidth = DWC3_MDWIDTH(dwc->hwparams.hwparams0);
+
+	/* MDWIDTH is represented in bits, convert to bytes */
+	mdwidth /= 8;
 
-	usb_ep_set_maxpacket_limit(&dep->endpoint, 1024);
+	/* All OUT endpoints share a single RxFIFO space */
+	size = dwc3_readl(dwc->regs, DWC3_GRXFIFOSIZ(0));
+	if (dwc3_is_usb31(dwc))
+		size = DWC31_GRXFIFOSIZ_RXFDEP(size);
+	else
+		size = DWC3_GRXFIFOSIZ_RXFDEP(size);
+
+	/* FIFO depth is in MDWDITH bytes */
+	size *= mdwidth;
+
+	/*
+	 * To meet performance requirement, a minimum recommended RxFIFO size
+	 * is defined as follow:
+	 * RxFIFO size >= (3 x MaxPacketSize) +
+	 * (3 x 8 bytes setup packets size) + (16 bytes clock crossing margin)
+	 *
+	 * Then calculate the max packet limit as below.
+	 */
+	size -= (3 * 8) + 16;
+	if (size < 0)
+		size = 0;
+	else
+		size /= 3;
+
+	usb_ep_set_maxpacket_limit(&dep->endpoint, size);
 	dep->endpoint.max_streams = 15;
 	dep->endpoint.ops = &dwc3_gadget_ep_ops;
 	list_add_tail(&dep->endpoint.ep_list,
-- 
2.20.1

[PATCH AUTOSEL 5.6 28/79] usb: dwc3: gadget: Do link recovery for SS and SSP

[Sasha Levin]

From: Thinh Nguyen <Thinh.Nguyen@synopsys.com>

[ Upstream commit d0550cd20e52558ecf6847a0f96ebd5d944c17e4 ]

The controller always supports link recovery for device in SS and SSP.
Remove the speed limit check. Also, when the device is in RESUME or
RESET state, it means the controller received the resume/reset request.
The driver must send the link recovery to acknowledge the request. They
are valid states for the driver to send link recovery.

Fixes: 72246da40f37 ("usb: Introduce DesignWare USB3 DRD Driver")
Fixes: ee5cd41c9117 ("usb: dwc3: Update speed checks for SuperSpeedPlus")
Signed-off-by: Thinh Nguyen <thinhn@synopsys.com>
Signed-off-by: Felipe Balbi <balbi@kernel.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
 drivers/usb/dwc3/gadget.c | 8 ++------
 1 file changed, 2 insertions(+), 6 deletions(-)

diff --git a/drivers/usb/dwc3/gadget.c b/drivers/usb/dwc3/gadget.c
index 1e68c90a83781..bc1cf6d0412a3 100644
--- a/drivers/usb/dwc3/gadget.c
+++ b/drivers/usb/dwc3/gadget.c
@@ -1728,7 +1728,6 @@ static int __dwc3_gadget_wakeup(struct dwc3 *dwc)
 	u32			reg;
 
 	u8			link_state;
-	u8			speed;
 
 	/*
 	 * According to the Databook Remote wakeup request should
@@ -1738,16 +1737,13 @@ static int __dwc3_gadget_wakeup(struct dwc3 *dwc)
 	 */
 	reg = dwc3_readl(dwc->regs, DWC3_DSTS);
 
-	speed = reg & DWC3_DSTS_CONNECTSPD;
-	if ((speed == DWC3_DSTS_SUPERSPEED) ||
-	    (speed == DWC3_DSTS_SUPERSPEED_PLUS))
-		return 0;
-
 	link_state = DWC3_DSTS_USBLNKST(reg);
 
 	switch (link_state) {
+	case DWC3_LINK_STATE_RESET:
 	case DWC3_LINK_STATE_RX_DET:	/* in HS, means Early Suspend */
 	case DWC3_LINK_STATE_U3:	/* in HS, means SUSPEND */
+	case DWC3_LINK_STATE_RESUME:
 		break;
 	default:
 		return -EINVAL;
-- 
2.20.1