From: Drew Fustini <drew@beagleboard.org>
To: Tony Lindgren <tony@atomide.com>
Cc: Haojian Zhuang <haojian.zhuang@linaro.org>,
Linus Walleij <linus.walleij@linaro.org>,
linux-omap@vger.kernel.org
Subject: Re: pinctrl-single: num_maps in generic pinconf support?
Date: Mon, 8 Jun 2020 20:05:43 +0200 [thread overview]
Message-ID: <20200608180543.GA2825296@x1> (raw)
In-Reply-To: <20200529174037.GT37466@atomide.com>
On Fri, May 29, 2020 at 10:40:37AM -0700, Tony Lindgren wrote:
> * Drew Fustini <drew@beagleboard.org> [200528 12:54]:
> > Would you be able to describe what you think AM33XX_PADCONF would look
> > like if the mux and conf are seperated?
>
> Yes it would just slightly change, see your example below.
>
> > Is there an example you know of for another SoC?
>
> I think the other driver already keep the padconf and mux separate.
>
> So not sure where all #pinctrl-cells could be used. It would make
> pinctrl-single.c a bit nicer though, and probably would make it
> easier to implement further features.
>
> Some hardware may need it to have #pinctrl-cells = <3> if GPIO
> features are there too, ideally pinctrl-single would not even
> care but just work for what is configured for the hardware.
>
> > Currently, the macro takes dir and mux:
> >
> > include/dt-bindings/pinctrl/omap.h:
> > #define AM33XX_PADCONF(pa, dir, mux) OMAP_IOPAD_OFFSET((pa), 0x0800) ((dir) | (mux))
>
> So after fixing up pinctrl-single.c, and changing the SoC dts
> to have #pinctrl-cells = <2> instead of <1>, the macro would
> then need to be:
>
> #define AM33XX_PADCONF(pa, dir, mux) OMAP_IOPAD_OFFSET((pa), 0x0800) (dir), (mux))
>
> > For example, in arch/arm/boot/dts/am335x-bone-common.dtsi:
> > AM33XX_PADCONF(AM335X_PIN_I2C0_SDA, PIN_INPUT_PULLUP, MUX_MODE0)
>
> Yeah so no change needed for the use.
>
> > I think it might be more accurate to rename 'dir' to 'conf'.
>
> Sure makes sense to rename it in the macro.
>
> Regards,
>
> Tony
Tony - would this be how the macro would need to be changed?
diff --git a/include/dt-bindings/pinctrl/omap.h b/include/dt-bindings/pinctrl/omap.h
index 625718042413..2d2a8c737822 100644
--- a/include/dt-bindings/pinctrl/omap.h
+++ b/include/dt-bindings/pinctrl/omap.h
@@ -65,7 +65,7 @@
#define DM814X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
#define DM816X_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
#define AM33XX_IOPAD(pa, val) OMAP_IOPAD_OFFSET((pa), 0x0800) (val)
-#define AM33XX_PADCONF(pa, dir, mux) OMAP_IOPAD_OFFSET((pa), 0x0800) ((dir) | (mux))
+#define AM33XX_PADCONF(pa, conf, mux) OMAP_IOPAD_OFFSET((pa), 0x0800) (conf) (mux)
/*
* Macros to allow using the offset from the padconf physical address
next prev parent reply other threads:[~2020-06-08 18:05 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-26 12:21 pinctrl-single: num_maps in generic pinconf support? Drew Fustini
2020-05-27 16:51 ` Tony Lindgren
2020-05-27 22:19 ` Drew Fustini
2020-05-27 22:41 ` Tony Lindgren
2020-05-28 12:53 ` Drew Fustini
2020-05-29 17:40 ` Tony Lindgren
2020-06-08 18:05 ` Drew Fustini [this message]
2020-06-08 20:22 ` Drew Fustini
2020-06-09 18:04 ` Tony Lindgren
2020-06-09 17:55 ` Tony Lindgren
2020-05-29 17:55 ` Drew Fustini
2020-05-31 0:17 ` Drew Fustini
2020-06-08 12:09 ` Linus Walleij
2020-06-08 12:40 ` Drew Fustini
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200608180543.GA2825296@x1 \
--to=drew@beagleboard.org \
--cc=haojian.zhuang@linaro.org \
--cc=linus.walleij@linaro.org \
--cc=linux-omap@vger.kernel.org \
--cc=tony@atomide.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).