Linux-OMAP Archive on lore.kernel.org
 help / color / Atom feed
From: Rob Herring <robh@kernel.org>
To: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
Cc: David Lechner <david@lechnology.com>,
	tglx@linutronix.de, jason@lakedaemon.net,
	Marc Zyngier <maz@kernel.org>, "Anna, Suman" <s-anna@ti.com>,
	Lee Jones <lee.jones@linaro.org>,
	devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
	linux-omap@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
	"Mills, William" <wmills@ti.com>,
	"Bajjuri, Praneeth" <praneeth@ti.com>,
	"Andrew F . Davis" <afd@ti.com>, Roger Quadros <rogerq@ti.com>
Subject: Re: [PATCH v4 1/5] dt-bindings: irqchip: Add PRU-ICSS interrupt controller bindings
Date: Fri, 31 Jul 2020 15:09:09 -0600
Message-ID: <20200731210909.GA779238@bogus> (raw)
In-Reply-To: <CAMxfBF6Ru1Fm1oWDyrSM=kBdCUe+eUDChqDgoYo4ziVr-8c50Q@mail.gmail.com>

On Fri, Jul 31, 2020 at 01:48:57PM +0200, Grzegorz Jaszczyk wrote:
> On Wed, 29 Jul 2020 at 19:34, David Lechner <david@lechnology.com> wrote:
> >
> > On 7/28/20 4:18 AM, Grzegorz Jaszczyk wrote:
> > > From: Suman Anna <s-anna@ti.com>
> > >
> > > The Programmable Real-Time Unit and Industrial Communication Subsystem
> > > (PRU-ICSS or simply PRUSS) contains an interrupt controller (INTC) that
> > > can handle various system input events and post interrupts back to the
> > > device-level initiators. The INTC can support upto 64 input events on
> >
> > nit: "up to" is two separate words
> 
> Ok.
> 
> >
> > > most SoCs with individual control configuration and h/w prioritization.
> > > These events are mapped onto 10 output interrupt lines through two levels
> > > of many-to-one mapping support. Different interrupt lines are routed to
> > > the individual PRU cores or to the host CPU or to other PRUSS instances.
> > >
> > > The K3 AM65x and J721E SoCs have the next generation of the PRU-ICSS IP,
> > > commonly called ICSSG. The ICSSG interrupt controller on K3 SoCs provide
> > > a higher number of host interrupts (20 vs 10) and can handle an increased
> > > number of input events (160 vs 64) from various SoC interrupt sources.
> > >
> > > Add the bindings document for these interrupt controllers on all the
> > > applicable SoCs. It covers the OMAP architecture SoCs - AM33xx, AM437x
> > > and AM57xx; the Keystone 2 architecture based 66AK2G SoC; the Davinci
> > > architecture based OMAPL138 SoCs, and the K3 architecture based AM65x
> > > and J721E SoCs.
> > >
> > > Signed-off-by: Suman Anna <s-anna@ti.com>
> > > Signed-off-by: Andrew F. Davis <afd@ti.com>
> > > Signed-off-by: Roger Quadros <rogerq@ti.com>
> > > Signed-off-by: Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>
> > > ---
> > > v3->v4:
> > > - Drop allOf references to interrupt-controller.yaml and
> > >    interrupts.yaml.
> > > - Drop items descriptions and use only maxItems: 1 as suggested by Rob.
> > > - Convert irqs-reserved property from uint8-array to bitmask.
> > > - Minor descriptions updates.
> > > - Change interrupt-cells to 3 in order to provide 2-level mapping
> > >    description for interrupts routed to the main CPU (as Marc requested).
> > > - Merge the irqs-reserved and irqs-shared to one property since they
> > >    can be handled by one logic.
> > > - Drop reviewed-by due to introduced changes.
> > > - Add another example illustrating irqs-reserved property usage.
> > > v2->v3:
> > > - Convert dt-binding to YAML
> > > v1->v2:
> > > - https://patchwork.kernel.org/patch/11069767/
> > > ---
> > >   .../interrupt-controller/ti,pruss-intc.yaml        | 157 +++++++++++++++++++++
> > >   1 file changed, 157 insertions(+)
> > >   create mode 100644 Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
> > >
> > > diff --git a/Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml b/Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
> > > new file mode 100644
> > > index 0000000..7336b11
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
> > > @@ -0,0 +1,157 @@
> > > +# SPDX-License-Identifier: (GPL-2.0-only or BSD-2-Clause)
> > > +%YAML 1.2
> > > +---
> > > +$id: http://devicetree.org/schemas/interrupt-controller/ti,pruss-intc.yaml#
> > > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > > +
> > > +title: TI PRU-ICSS Local Interrupt Controller
> > > +
> > > +maintainers:
> > > +  - Suman Anna <s-anna@ti.com>
> > > +
> > > +description: |
> > > +  Each PRU-ICSS has a single interrupt controller instance that is common
> > > +  to all the PRU cores. Most interrupt controllers can route 64 input events
> > > +  which are then mapped to 10 possible output interrupts through two levels
> > > +  of mapping. The input events can be triggered by either the PRUs and/or
> > > +  various other PRUSS internal and external peripherals. The first 2 output
> > > +  interrupts (0, 1) are fed exclusively to the internal PRU cores, with the
> > > +  remaining 8 (2 through 9) connected to external interrupt controllers
> > > +  including the MPU and/or other PRUSS instances, DSPs or devices.
> > > +
> > > +  The property "ti,irqs-reserved" is used for denoting the connection
> > > +  differences on the output interrupts 2 through 9. If this property is not
> > > +  defined, it implies that all the PRUSS INTC output interrupts 2 through 9
> > > +  (host_intr0 through host_intr7) are connected exclusively to the Arm interrupt
> > > +  controller.
> > > +
> > > +  The K3 family of SoCs can handle 160 input events that can be mapped to 20
> > > +  different possible output interrupts. The additional output interrupts (10
> > > +  through 19) are connected to new sub-modules within the ICSSG instances.
> > > +
> > > +  This interrupt-controller node should be defined as a child node of the
> > > +  corresponding PRUSS node. The node should be named "interrupt-controller".
> > > +
> > > +properties:
> > > +  compatible:
> > > +    enum:
> > > +      - ti,pruss-intc
> > > +      - ti,icssg-intc
> > > +    description: |
> > > +      Use "ti,pruss-intc" for OMAP-L13x/AM18x/DA850 SoCs,
> > > +                              AM335x family of SoCs,
> > > +                              AM437x family of SoCs,
> > > +                              AM57xx family of SoCs
> > > +                              66AK2G family of SoCs
> > > +      Use "ti,icssg-intc" for K3 AM65x & J721E family of SoCs
> > > +
> > > +  reg:
> > > +    maxItems: 1
> > > +
> > > +  interrupts:
> > > +    minItems: 1
> > > +    maxItems: 8
> > > +    description: |
> > > +      All the interrupts generated towards the main host processor in the SoC.
> > > +      A shared interrupt can be skipped if the desired destination and usage is
> > > +      by a different processor/device.
> >
> > This sounds like using device tree for configuration. Also, isn't this what the
> > ti,irqs-reserved property is for?
> 
> Yes this is what ti,irqs-reserved is also used for. The intention was
> to keep both in sync, so it would be less confusing: if some
> interrupts are on irqs-reserved list, they shouldn't be present here.
> In terms of shared interrupt usage I will not call it configuration
> via device-tree, rather design description (for single device tree
> description given shared interrupt is used or as MCPU one or as
> different processor/device one).
> 
> >
> > > +
> > > +  interrupt-names:
> > > +    minItems: 1
> > > +    maxItems: 8
> > > +    items:
> > > +      pattern: host_intr[0-7]
> > > +    description: |
> > > +      Should use one of the above names for each valid host event interrupt
> > > +      connected to Arm interrupt controller, the name should match the
> > > +      corresponding host event interrupt number.
> > > +
> > > +  interrupt-controller: true
> > > +
> > > +  "#interrupt-cells":
> > > +    const: 3
> > > +    description: |
> > > +      Client users shall use the PRU System event number (the interrupt source
> > > +      that the client is interested in), PRU channel and PRU host_intr (target)
> > > +      as the value of the interrupts property in their node.  The system events
> > > +      can be mapped to some output host interrupts through 2 levels of
> > > +      many-to-one mapping i.e. events to channel mapping and channels to host
> > > +      interrupts so through this property entire mapping is provided.
> >
> > It is not clear what the meaning of each cell is. Looking at later patches, it
> > looks like the first cell is the PRU system event number, the second cell is the
> > channel and the third cell is the host event number.
> 
> Ok, how about updating above description like this:
> Client users shall use the PRU System event number (the interrupt source
> that the client is interested in) [cell 1], PRU channel [cell 2] and PRU
> host_intr (target) [cell 3] as the value of the interrupts property in their
> node.  The system events can be mapped to some output host interrupts through 2
> levels of many-to-one mapping i.e. events to channel mapping and channels to
> host interrupts so through this property entire mapping is provided.
> 
> >
> > > +
> > > +  ti,irqs-reserved:
> > > +    $ref: /schemas/types.yaml#definitions/uint8
> >
> > Is 8 bits enough for any possible future devices? It is written above that there are
> > already up to 20 host events on some devices even if only 8 are connected to the MCU.
> 
> We've already discussed this with Suman: it is unlikely that HW with
> more than 8 host interrupts connected to the MCU will arrive.
> 
> >
> > > +    description: |
> > > +      Bitmask of host interrupts between 0 and 7 (corresponding to PRUSS INTC
> > > +      output interrupts 2 through 9) that are not connected to the Arm interrupt
> > > +      controller or are shared and used by other devices or processors in the
> > > +      SoC. Define this property when any of 8 interrupts should not be handled
> > > +      by Arm interrupt controller.
> > > +        Eg: - AM437x and 66AK2G SoCs do not have "host_intr5" interrupt
> > > +              connected to MPU
> > > +            - AM65x and J721E SoCs have "host_intr5", "host_intr6" and
> > > +              "host_intr7" interrupts connected to MPU, and other ICSSG
> > > +              instances.
> > > +
> > > +required:
> > > + - compatible
> > > + - reg
> > > + - interrupts
> > > + - interrupt-names
> > > + - interrupt-controller
> > > + - "#interrupt-cells"
> > > +
> > > +additionalProperties: false
> > > +
> > > +examples:
> > > +  - |
> > > +    /* AM33xx PRU-ICSS */
> > > +    pruss: pruss@0 {
> > > +        compatible = "ti,am3356-pruss";
> > > +        reg = <0x0 0x80000>;
> > > +        #address-cells = <1>;
> > > +        #size-cells = <1>;
> > > +        ranges;
> > > +
> > > +        pruss_intc: interrupt-controller@20000 {
> > > +            compatible = "ti,pruss-intc";
> > > +            reg = <0x20000 0x2000>;
> > > +            interrupts = <20 21 22 23 24 25 26 27>;
> > > +            interrupt-names = "host_intr0", "host_intr1",
> > > +                              "host_intr2", "host_intr3",
> > > +                              "host_intr4", "host_intr5",
> > > +                              "host_intr6", "host_intr7";
> > > +            interrupt-controller;
> > > +            #interrupt-cells = <3>;
> > > +        };
> > > +    };
> > > +
> > > +  - |
> > > +
> > > +    /* AM4376 PRU-ICSS */
> > > +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> > > +    pruss@0 {
> > > +        compatible = "ti,am4376-pruss";
> > > +        reg = <0x0 0x40000>;
> > > +        #address-cells = <1>;
> > > +        #size-cells = <1>;
> > > +        ranges;
> > > +
> > > +        interrupt-controller@20000 {
> > > +            compatible = "ti,pruss-intc";
> > > +            reg = <0x20000 0x2000>;
> > > +            interrupt-controller;
> > > +            #interrupt-cells = <3>;
> > > +            interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>,
> > > +                   <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>,
> > > +                   <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>,
> > > +                   <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>,
> > > +                   <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>,
> > > +                   <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>,
> > > +                   <GIC_SPI 27 IRQ_TYPE_LEVEL_HIGH>;
> > > +            interrupt-names = "host_intr0", "host_intr1",
> > > +                              "host_intr2", "host_intr3",
> > > +                              "host_intr4",
> > > +                              "host_intr6", "host_intr7";
> > > +            ti,irqs-reserved = /bits/ 8 <0x20>; /* BIT(5) */
> >
> > Is 0b00100000 valid syntax in device tree (instead of 0x20 + comment)?

Using binary? No.

> Actually I think more readable will be to define and use BIT()
> directly. Similar to what is done for one of the omap dtsi:
> https://elixir.bootlin.com/linux/latest/source/arch/arm/boot/dts/omap3-gta04.dtsi#L648

No, please don't add/use BIT(). I'd assume the common case here is not 
only 1 bit set. Even if it is here, it's not in general, and I just 
don't want more macros.

Rob

  parent reply index

Thread overview: 24+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-28  9:18 [PATCH v4 0/5] Add TI PRUSS Local Interrupt Controller IRQChip driver Grzegorz Jaszczyk
2020-07-28  9:18 ` [PATCH v4 1/5] dt-bindings: irqchip: Add PRU-ICSS interrupt controller bindings Grzegorz Jaszczyk
2020-07-29 17:34   ` David Lechner
2020-07-31 11:48     ` Grzegorz Jaszczyk
2020-07-31 14:09       ` David Lechner
2020-07-31 14:16         ` Grzegorz Jaszczyk
2020-07-31 14:35           ` Suman Anna
2020-07-31 21:09       ` Rob Herring [this message]
2020-08-02 21:49         ` Grzegorz Jaszczyk
2020-07-28  9:18 ` [PATCH v4 2/5] irqchip/irq-pruss-intc: Add a PRUSS irqchip driver for PRUSS interrupts Grzegorz Jaszczyk
2020-07-29 18:43   ` David Lechner
2020-07-31 11:57     ` Grzegorz Jaszczyk
2020-07-28  9:18 ` [PATCH v4 3/5] irqchip/irq-pruss-intc: Add logic for handling reserved interrupts Grzegorz Jaszczyk
2020-07-28 16:37   ` Marc Zyngier
2020-07-28 22:23     ` Grzegorz Jaszczyk
2020-07-29 18:48   ` David Lechner
2020-07-31 14:11     ` Grzegorz Jaszczyk
2020-07-28  9:18 ` [PATCH v4 4/5] irqchip/irq-pruss-intc: Implement irq_{get,set}_irqchip_state ops Grzegorz Jaszczyk
2020-07-29 19:23   ` David Lechner
2020-07-31 12:28     ` Grzegorz Jaszczyk
2020-07-31 15:59       ` David Lechner
2020-07-28  9:18 ` [PATCH v4 5/5] irqchip/irq-pruss-intc: Add support for ICSSG INTC on K3 SoCs Grzegorz Jaszczyk
2020-07-29 19:28   ` David Lechner
2020-07-31 12:32     ` Grzegorz Jaszczyk

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200731210909.GA779238@bogus \
    --to=robh@kernel.org \
    --cc=afd@ti.com \
    --cc=david@lechnology.com \
    --cc=devicetree@vger.kernel.org \
    --cc=grzegorz.jaszczyk@linaro.org \
    --cc=jason@lakedaemon.net \
    --cc=lee.jones@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=maz@kernel.org \
    --cc=praneeth@ti.com \
    --cc=rogerq@ti.com \
    --cc=s-anna@ti.com \
    --cc=tglx@linutronix.de \
    --cc=wmills@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-OMAP Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-omap/0 linux-omap/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-omap linux-omap/ https://lore.kernel.org/linux-omap \
		linux-omap@vger.kernel.org
	public-inbox-index linux-omap

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-omap


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git