From: Grygorii Strashko <grygorii.strashko@ti.com>
To: Tony Lindgren <tony@atomide.com>
Cc: <linux-omap@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
Sekhar Nori <nsekhar@ti.com>,
Vignesh Raghavendra <vigneshr@ti.com>,
Murali Karicheri <m-karicheri2@ti.com>,
Grygorii Strashko <grygorii.strashko@ti.com>
Subject: [PATCH next 4/6] ARM: dts: dra7x-evm: switch to new cpsw switch drv
Date: Mon, 7 Sep 2020 23:21:23 +0300 [thread overview]
Message-ID: <20200907202125.22943-5-grygorii.strashko@ti.com> (raw)
In-Reply-To: <20200907202125.22943-1-grygorii.strashko@ti.com>
Switch all TI DRA7x boards to use new cpsw switch driver. Those boards
configured in dual_mac mode by default. Hence, dual_mac mode has been
preserved the same way between legacy and new driver it's safe to switch
drivers.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
---
arch/arm/boot/dts/dra7-evm.dts | 13 ++++++-------
arch/arm/boot/dts/dra71-evm.dts | 14 +++++++-------
arch/arm/boot/dts/dra72-evm-common.dtsi | 4 ----
arch/arm/boot/dts/dra72-evm-revc.dts | 14 +++++++-------
arch/arm/boot/dts/dra72-evm.dts | 13 +++++++++----
arch/arm/boot/dts/dra76-evm.dts | 14 ++++++--------
6 files changed, 35 insertions(+), 37 deletions(-)
diff --git a/arch/arm/boot/dts/dra7-evm.dts b/arch/arm/boot/dts/dra7-evm.dts
index a952d934fcf2..051aac4e95b7 100644
--- a/arch/arm/boot/dts/dra7-evm.dts
+++ b/arch/arm/boot/dts/dra7-evm.dts
@@ -537,24 +537,23 @@
ti,no-idle-on-init;
};
-&mac {
+&mac_sw {
status = "okay";
- dual_emac;
};
-&cpsw_emac0 {
+&cpsw_port1 {
phy-handle = <ðphy0>;
phy-mode = "rgmii";
- dual_emac_res_vlan = <1>;
+ ti,dual-emac-pvid = <1>;
};
-&cpsw_emac1 {
+&cpsw_port2 {
phy-handle = <ðphy1>;
phy-mode = "rgmii";
- dual_emac_res_vlan = <2>;
+ ti,dual-emac-pvid = <2>;
};
-&davinci_mdio {
+&davinci_mdio_sw {
ethphy0: ethernet-phy@2 {
reg = <2>;
};
diff --git a/arch/arm/boot/dts/dra71-evm.dts b/arch/arm/boot/dts/dra71-evm.dts
index 10da51bee42f..cad58f733bd6 100644
--- a/arch/arm/boot/dts/dra71-evm.dts
+++ b/arch/arm/boot/dts/dra71-evm.dts
@@ -219,26 +219,26 @@
vqmmc-supply = <&evm_1v8_sw>;
};
-&mac {
+&mac_sw {
mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
<&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */
<&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */
- dual_emac;
+ status = "okay";
};
-&cpsw_emac0 {
+&cpsw_port1 {
phy-handle = <&dp83867_0>;
phy-mode = "rgmii-id";
- dual_emac_res_vlan = <1>;
+ ti,dual-emac-pvid = <1>;
};
-&cpsw_emac1 {
+&cpsw_port2 {
phy-handle = <&dp83867_1>;
phy-mode = "rgmii-id";
- dual_emac_res_vlan = <2>;
+ ti,dual-emac-pvid = <2>;
};
-&davinci_mdio {
+&davinci_mdio_sw {
dp83867_0: ethernet-phy@2 {
reg = <2>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
diff --git a/arch/arm/boot/dts/dra72-evm-common.dtsi b/arch/arm/boot/dts/dra72-evm-common.dtsi
index 9273a7d6fa29..8d0d960107fb 100644
--- a/arch/arm/boot/dts/dra72-evm-common.dtsi
+++ b/arch/arm/boot/dts/dra72-evm-common.dtsi
@@ -462,10 +462,6 @@
};
};
-&mac {
- status = "okay";
-};
-
&dcan1 {
status = "ok";
pinctrl-names = "default", "sleep", "active";
diff --git a/arch/arm/boot/dts/dra72-evm-revc.dts b/arch/arm/boot/dts/dra72-evm-revc.dts
index 54dab0f212d1..f242b937f88c 100644
--- a/arch/arm/boot/dts/dra72-evm-revc.dts
+++ b/arch/arm/boot/dts/dra72-evm-revc.dts
@@ -77,26 +77,26 @@
interrupts = <30 IRQ_TYPE_EDGE_FALLING>;
};
-&mac {
+&mac_sw {
mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_LOW>,
<&pcf_hdmi 9 GPIO_ACTIVE_LOW>, /* P11 */
<&pcf_hdmi 10 GPIO_ACTIVE_LOW>; /* P12 */
- dual_emac;
+ status = "okay";
};
-&cpsw_emac0 {
+&cpsw_port1 {
phy-handle = <&dp83867_0>;
phy-mode = "rgmii-id";
- dual_emac_res_vlan = <1>;
+ ti,dual-emac-pvid = <1>;
};
-&cpsw_emac1 {
+&cpsw_port2 {
phy-handle = <&dp83867_1>;
phy-mode = "rgmii-id";
- dual_emac_res_vlan = <2>;
+ ti,dual-emac-pvid = <2>;
};
-&davinci_mdio {
+&davinci_mdio_sw {
dp83867_0: ethernet-phy@2 {
reg = <2>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
diff --git a/arch/arm/boot/dts/dra72-evm.dts b/arch/arm/boot/dts/dra72-evm.dts
index 6ea9936f7d9c..5f62f92eb96c 100644
--- a/arch/arm/boot/dts/dra72-evm.dts
+++ b/arch/arm/boot/dts/dra72-evm.dts
@@ -69,17 +69,22 @@
interrupts = <11 IRQ_TYPE_EDGE_FALLING>;
};
-&mac {
- slaves = <1>;
+&mac_sw {
mode-gpios = <&pcf_gpio_21 4 GPIO_ACTIVE_HIGH>;
+ status = "okay";
};
-&cpsw_emac0 {
+&cpsw_port1 {
phy-handle = <ðphy0>;
phy-mode = "rgmii";
+ ti,dual-emac-pvid = <1>;
+};
+
+&cpsw_port2 {
+ status = "disabled";
};
-&davinci_mdio {
+&davinci_mdio_sw {
ethphy0: ethernet-phy@3 {
reg = <3>;
};
diff --git a/arch/arm/boot/dts/dra76-evm.dts b/arch/arm/boot/dts/dra76-evm.dts
index 803981cc762e..34f655be4fb4 100644
--- a/arch/arm/boot/dts/dra76-evm.dts
+++ b/arch/arm/boot/dts/dra76-evm.dts
@@ -475,25 +475,23 @@
status = "disabled";
};
-&mac {
+&mac_sw {
status = "okay";
-
- dual_emac;
};
-&cpsw_emac0 {
+&cpsw_port1 {
phy-handle = <&dp83867_0>;
phy-mode = "rgmii-id";
- dual_emac_res_vlan = <1>;
+ ti,dual-emac-pvid = <1>;
};
-&cpsw_emac1 {
+&cpsw_port2 {
phy-handle = <&dp83867_1>;
phy-mode = "rgmii-id";
- dual_emac_res_vlan = <2>;
+ ti,dual-emac-pvid = <2>;
};
-&davinci_mdio {
+&davinci_mdio_sw {
dp83867_0: ethernet-phy@2 {
reg = <2>;
ti,rx-internal-delay = <DP83867_RGMIIDCTL_2_25_NS>;
--
2.17.1
next prev parent reply other threads:[~2020-09-07 20:22 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-09-07 20:21 [PATCH next 0/6] ARM: dts: am57xx/dra7x: switch to new cpsw switch drv Grygorii Strashko
2020-09-07 20:21 ` [PATCH next 1/6] ARM: dts: am5729: beagleboneai: " Grygorii Strashko
2020-09-07 20:21 ` [PATCH next 2/6] ARM: dts: am57xx-idk: " Grygorii Strashko
2020-09-07 20:21 ` [PATCH next 3/6] ARM: dts: beagle-x15: " Grygorii Strashko
2020-09-07 20:21 ` Grygorii Strashko [this message]
2020-09-07 20:21 ` [PATCH next 5/6] ARM: dts: am57xx-cl-som-am57x: " Grygorii Strashko
2020-09-07 20:21 ` [PATCH next 6/6] ARM: dts: dra7: drop legacy cpsw dt node Grygorii Strashko
2020-09-10 9:52 ` [PATCH next 0/6] ARM: dts: am57xx/dra7x: switch to new cpsw switch drv Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200907202125.22943-5-grygorii.strashko@ti.com \
--to=grygorii.strashko@ti.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-omap@vger.kernel.org \
--cc=m-karicheri2@ti.com \
--cc=nsekhar@ti.com \
--cc=tony@atomide.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).