Re: beaglebone black boot failure Linux v5.15.rc1

[Grygorii Strashko <grygorii.strashko@ti.com>]

On 17/09/2021 13:57, Grygorii Strashko wrote:
> 
> 
> On 17/09/2021 13:28, Vaittinen, Matti wrote:
>> Hi deeee Ho Tony & All,
>>
>> On 9/17/21 09:14, Tony Lindgren wrote:
>>> Hi,
>>>
>>> * Vaittinen, Matti <Matti.Vaittinen@fi.rohmeurope.com> [210916 09:15]:
>>
>>>> My beaglebone black (rev c) based test environment fails to boot with
>>>> v5.15-rc1. Boot succeeds with the v5.14.
>>>>
>>>> Bisecting the Linus' tree pointed out the commit:
>>>> [1c7ba565e70365763ea780666a3eee679344b962] ARM: dts: am335x-baltos:
>>>> switch to new cpsw switch drv
>>>>
>>>> I don't see this exact commit touching the BBB device-tree. In Linus'
>>>> tree it is a part of a merge commit. Reverting the whole merge on top of
>>>> the v5.15-rc1
>>>>
>>>> This reverts commit 81b6a285737700c2e04ef0893617b80481b6b4b7, reversing
>>>> changes made to f73979109bc11a0ed26b6deeb403fb5d05676ffc.
>>>>
>>>> makes my beaglebone black to boot again.
>>>>
>>>> Yesterday I tried adding this patch:
>>>> https://lore.kernel.org/linux-omap/20210915065032.45013-1-tony@atomide.com/T/#u
>>>> pointed by Tom on top of the v5.15-rc1 - no avail. I also did #define
>>>> DEBUG at ti-sys.c as was suggested by Tom - but I don't see any more output.
>>>
>>> Correction, that was me, not Tom :)
>>
>> Oh.. Sorry! I don't know where I picked Tom from... My bad!
>>
>>> For me, adding any kind of delay fixed the issue. Also adding some printk
>>> statements fixed it for me.
>>>
>>>> Any suggestions what to check next?
>>>
>>> Maybe try the attached patch? If it helps, just try with the with the
>>> ti,sysc-delay-us = <2> added as few modules need that after enable.
>>>
>>> It's also possible there is an issue with some other device that is now
>>> getting enabled other than pruss. The last XXX printk output should show
>>> the last device being probed.
>>>
>>> Looks like you need to also enable CONFIG_SERIAL_EARLYCON=y, and pass
>>> console=ttyS0,115200 debug earlycon in the kernel command line.
>>
>> Ah. Thanks again. I indeed lacked the "debug earlycon" parameters. Now
>> we're more likely to see what went wrong :) I pasted the serial log form
>> failing boot with v5.15-rc1 which has both the patch you linked me above
>> and the patch you suggested me to test in previous email.
>>
> 
> [...]
> 
>> [    2.786181] ti-sysc 48311fe0.target-module: XXX sysc_probe
>> [    2.791994] ti-sysc 48311fe0.target-module:
>> 48310000:2000:1fe0:1fe4:NA:00000020:rng
>> [    2.800820] omap_rng 48310000.rng: Random Number Generator ver. 20
>> [    2.807315] random: crng init done
>> [    2.814207] ti-sysc 4a101200.target-module: XXX sysc_probe
>> [    2.820080] ti-sysc 4a101200.target-module:
>> 4a100000:8000:1200:1208:1204:4edb0100:cpgmac
> 
> This one cpsw
> 
>> [    2.830347] ti-sysc 4a326000.target-module: XXX sysc_probe
> 
> This one pruss and it still shows sysc_probe
> 
> Not sure what are the dependency here :( if any.
> 
> Additional option to try - cmdline param "initcall_debug" and maybe increase print level in really_probe_debug()
> 

Just to be clear - idea is to see *all* probes - not only sysc.

[...]

-- 
Best regards,
grygorii