Linux-OMAP Archive on lore.kernel.org
 help / color / Atom feed
From: Tero Kristo <kristo@kernel.org>
To: Dario Binacchi <dariobin@libero.it>, linux-kernel@vger.kernel.org
Cc: Grygorii Strashko <grygorii.strashko@ti.com>,
	Lee Jones <lee.jones@linaro.org>,
	Michael Turquette <mturquette@baylibre.com>,
	Stephen Boyd <sboyd@kernel.org>,
	linux-clk@vger.kernel.org, linux-omap@vger.kernel.org
Subject: Re: [PATCH v5 5/5] clk: ti: add am33xx/am43xx spread spectrum clock support
Date: Mon, 19 Apr 2021 14:26:24 +0300
Message-ID: <3e6472c2-5256-0248-6a09-32a59a74832e@kernel.org> (raw)
In-Reply-To: <20210418145655.10415-6-dariobin@libero.it>

On 18/04/2021 17:56, Dario Binacchi wrote:
> The patch enables spread spectrum clocking (SSC) for MPU and LCD PLLs.
> As reported by the TI spruh73x/spruhl7x RM, SSC is only supported for
> the DISP/LCD and MPU PLLs on am33xx/am43xx. SSC is not supported for
> DDR, PER, and CORE PLLs.
> 
> Calculating the required values and setting the registers accordingly
> was taken from the set_mpu_spreadspectrum routine contained in the
> arch/arm/mach-omap2/am33xx/clock_am33xx.c file of the u-boot project.
> 
> In locked condition, DPLL output clock = CLKINP *[M/N]. In case of
> SSC enabled, the reference manual explains that there is a restriction
> of range of M values. Since the omap2_dpll_round_rate routine attempts
> to select the minimum possible N, the value of M obtained is not
> guaranteed to be within the range required. With the new "ti,min-div"
> parameter it is possible to increase N and consequently M to satisfy the
> constraint imposed by SSC.
> 
> Signed-off-by: Dario Binacchi <dariobin@libero.it>

Reviewed-by: Tero Kristo <kristo@kernel.org>

> 
> ---
> 
> Changes in v5:
> - Remove ssc_ack_mask field from dpll_data structure. It was not used.
> - Change ssc_downspread type from u8 to bool in dpll_data structure.
> 
> Changes in v4:
> - Update commit message.
> 
> Changes in v3:
> - Use "ti,ssc-modfreq-hz" binding instead of "ti,ssc-modfreq".
> 
> Changes in v2:
> - Move the DT changes to the previous patch in the series.
> 
>   drivers/clk/ti/dpll.c     | 39 ++++++++++++++++++
>   drivers/clk/ti/dpll3xxx.c | 85 +++++++++++++++++++++++++++++++++++++++
>   include/linux/clk/ti.h    | 22 ++++++++++
>   3 files changed, 146 insertions(+)
> 
> diff --git a/drivers/clk/ti/dpll.c b/drivers/clk/ti/dpll.c
> index d6f1ac5b53e1..e9f9aee936ae 100644
> --- a/drivers/clk/ti/dpll.c
> +++ b/drivers/clk/ti/dpll.c
> @@ -290,7 +290,9 @@ static void __init of_ti_dpll_setup(struct device_node *node,
>   	struct clk_init_data *init = NULL;
>   	const char **parent_names = NULL;
>   	struct dpll_data *dd = NULL;
> +	int ssc_clk_index;
>   	u8 dpll_mode = 0;
> +	u32 min_div;
>   
>   	dd = kmemdup(ddt, sizeof(*dd), GFP_KERNEL);
>   	clk_hw = kzalloc(sizeof(*clk_hw), GFP_KERNEL);
> @@ -345,6 +347,27 @@ static void __init of_ti_dpll_setup(struct device_node *node,
>   	if (dd->autoidle_mask) {
>   		if (ti_clk_get_reg_addr(node, 3, &dd->autoidle_reg))
>   			goto cleanup;
> +
> +		ssc_clk_index = 4;
> +	} else {
> +		ssc_clk_index = 3;
> +	}
> +
> +	if (dd->ssc_deltam_int_mask && dd->ssc_deltam_frac_mask &&
> +	    dd->ssc_modfreq_mant_mask && dd->ssc_modfreq_exp_mask) {
> +		if (ti_clk_get_reg_addr(node, ssc_clk_index++,
> +					&dd->ssc_deltam_reg))
> +			goto cleanup;
> +
> +		if (ti_clk_get_reg_addr(node, ssc_clk_index++,
> +					&dd->ssc_modfreq_reg))
> +			goto cleanup;
> +
> +		of_property_read_u32(node, "ti,ssc-modfreq-hz",
> +				     &dd->ssc_modfreq);
> +		of_property_read_u32(node, "ti,ssc-deltam", &dd->ssc_deltam);
> +		dd->ssc_downspread =
> +			of_property_read_bool(node, "ti,ssc-downspread");
>   	}
>   
>   	if (of_property_read_bool(node, "ti,low-power-stop"))
> @@ -356,6 +379,10 @@ static void __init of_ti_dpll_setup(struct device_node *node,
>   	if (of_property_read_bool(node, "ti,lock"))
>   		dpll_mode |= 1 << DPLL_LOCKED;
>   
> +	if (!of_property_read_u32(node, "ti,min-div", &min_div) &&
> +	    min_div > dd->min_divider)
> +		dd->min_divider = min_div;
> +
>   	if (dpll_mode)
>   		dd->modes = dpll_mode;
>   
> @@ -585,8 +612,14 @@ static void __init of_ti_am3_no_gate_dpll_setup(struct device_node *node)
>   	const struct dpll_data dd = {
>   		.idlest_mask = 0x1,
>   		.enable_mask = 0x7,
> +		.ssc_enable_mask = 0x1 << 12,
> +		.ssc_downspread_mask = 0x1 << 14,
>   		.mult_mask = 0x7ff << 8,
>   		.div1_mask = 0x7f,
> +		.ssc_deltam_int_mask = 0x3 << 18,
> +		.ssc_deltam_frac_mask = 0x3ffff,
> +		.ssc_modfreq_mant_mask = 0x7f,
> +		.ssc_modfreq_exp_mask = 0x7 << 8,
>   		.max_multiplier = 2047,
>   		.max_divider = 128,
>   		.min_divider = 1,
> @@ -645,8 +678,14 @@ static void __init of_ti_am3_dpll_setup(struct device_node *node)
>   	const struct dpll_data dd = {
>   		.idlest_mask = 0x1,
>   		.enable_mask = 0x7,
> +		.ssc_enable_mask = 0x1 << 12,
> +		.ssc_downspread_mask = 0x1 << 14,
>   		.mult_mask = 0x7ff << 8,
>   		.div1_mask = 0x7f,
> +		.ssc_deltam_int_mask = 0x3 << 18,
> +		.ssc_deltam_frac_mask = 0x3ffff,
> +		.ssc_modfreq_mant_mask = 0x7f,
> +		.ssc_modfreq_exp_mask = 0x7 << 8,
>   		.max_multiplier = 2047,
>   		.max_divider = 128,
>   		.min_divider = 1,
> diff --git a/drivers/clk/ti/dpll3xxx.c b/drivers/clk/ti/dpll3xxx.c
> index 94d5b5fe9a2b..e32b3515f9e7 100644
> --- a/drivers/clk/ti/dpll3xxx.c
> +++ b/drivers/clk/ti/dpll3xxx.c
> @@ -291,6 +291,88 @@ static void _lookup_sddiv(struct clk_hw_omap *clk, u8 *sd_div, u16 m, u8 n)
>   	*sd_div = sd;
>   }
>   
> +/**
> + * omap3_noncore_dpll_ssc_program - set spread-spectrum clocking registers
> + * @clk:	struct clk * of DPLL to set
> + *
> + * Enable the DPLL spread spectrum clocking if frequency modulation and
> + * frequency spreading have been set, otherwise disable it.
> + */
> +static void omap3_noncore_dpll_ssc_program(struct clk_hw_omap *clk)
> +{
> +	struct dpll_data *dd = clk->dpll_data;
> +	unsigned long ref_rate;
> +	u32 v, ctrl, mod_freq_divider, exponent, mantissa;
> +	u32 deltam_step, deltam_ceil;
> +
> +	ctrl = ti_clk_ll_ops->clk_readl(&dd->control_reg);
> +
> +	if (dd->ssc_modfreq && dd->ssc_deltam) {
> +		ctrl |= dd->ssc_enable_mask;
> +
> +		if (dd->ssc_downspread)
> +			ctrl |= dd->ssc_downspread_mask;
> +		else
> +			ctrl &= ~dd->ssc_downspread_mask;
> +
> +		ref_rate = clk_hw_get_rate(dd->clk_ref);
> +		mod_freq_divider =
> +		    (ref_rate / dd->last_rounded_n) / (4 * dd->ssc_modfreq);
> +		if (dd->ssc_modfreq > (ref_rate / 70))
> +			pr_warn("clock: SSC modulation frequency of DPLL %s greater than %ld\n",
> +				__clk_get_name(clk->hw.clk), ref_rate / 70);
> +
> +		exponent = 0;
> +		mantissa = mod_freq_divider;
> +		while ((mantissa > 127) && (exponent < 7)) {
> +			exponent++;
> +			mantissa /= 2;
> +		}
> +		if (mantissa > 127)
> +			mantissa = 127;
> +
> +		v = ti_clk_ll_ops->clk_readl(&dd->ssc_modfreq_reg);
> +		v &= ~(dd->ssc_modfreq_mant_mask | dd->ssc_modfreq_exp_mask);
> +		v |= mantissa << __ffs(dd->ssc_modfreq_mant_mask);
> +		v |= exponent << __ffs(dd->ssc_modfreq_exp_mask);
> +		ti_clk_ll_ops->clk_writel(v, &dd->ssc_modfreq_reg);
> +
> +		deltam_step = dd->last_rounded_m * dd->ssc_deltam;
> +		deltam_step /= 10;
> +		if (dd->ssc_downspread)
> +			deltam_step /= 2;
> +
> +		deltam_step <<= __ffs(dd->ssc_deltam_int_mask);
> +		deltam_step /= 100;
> +		deltam_step /= mod_freq_divider;
> +		if (deltam_step > 0xFFFFF)
> +			deltam_step = 0xFFFFF;
> +
> +		deltam_ceil = (deltam_step & dd->ssc_deltam_int_mask) >>
> +		    __ffs(dd->ssc_deltam_int_mask);
> +		if (deltam_step & dd->ssc_deltam_frac_mask)
> +			deltam_ceil++;
> +
> +		if ((dd->ssc_downspread &&
> +		     ((dd->last_rounded_m - (2 * deltam_ceil)) < 20 ||
> +		      dd->last_rounded_m > 2045)) ||
> +		    ((dd->last_rounded_m - deltam_ceil) < 20 ||
> +		     (dd->last_rounded_m + deltam_ceil) > 2045))
> +			pr_warn("clock: SSC multiplier of DPLL %s is out of range\n",
> +				__clk_get_name(clk->hw.clk));
> +
> +		v = ti_clk_ll_ops->clk_readl(&dd->ssc_deltam_reg);
> +		v &= ~(dd->ssc_deltam_int_mask | dd->ssc_deltam_frac_mask);
> +		v |= deltam_step << __ffs(dd->ssc_deltam_int_mask |
> +					  dd->ssc_deltam_frac_mask);
> +		ti_clk_ll_ops->clk_writel(v, &dd->ssc_deltam_reg);
> +	} else {
> +		ctrl &= ~dd->ssc_enable_mask;
> +	}
> +
> +	ti_clk_ll_ops->clk_writel(ctrl, &dd->control_reg);
> +}
> +
>   /**
>    * omap3_noncore_dpll_program - set non-core DPLL M,N values directly
>    * @clk:	struct clk * of DPLL to set
> @@ -390,6 +472,9 @@ static int omap3_noncore_dpll_program(struct clk_hw_omap *clk, u16 freqsel)
>   		ti_clk_ll_ops->clk_writel(v, &dd->control_reg);
>   	}
>   
> +	if (dd->ssc_enable_mask)
> +		omap3_noncore_dpll_ssc_program(clk);
> +
>   	/* We let the clock framework set the other output dividers later */
>   
>   	/* REVISIT: Set ramp-up delay? */
> diff --git a/include/linux/clk/ti.h b/include/linux/clk/ti.h
> index c62f6fa6763d..3486f20a3753 100644
> --- a/include/linux/clk/ti.h
> +++ b/include/linux/clk/ti.h
> @@ -63,6 +63,17 @@ struct clk_omap_reg {
>    * @auto_recal_bit: bitshift of the driftguard enable bit in @control_reg
>    * @recal_en_bit: bitshift of the PRM_IRQENABLE_* bit for recalibration IRQs
>    * @recal_st_bit: bitshift of the PRM_IRQSTATUS_* bit for recalibration IRQs
> + * @ssc_deltam_reg: register containing the DPLL SSC frequency spreading
> + * @ssc_modfreq_reg: register containing the DPLL SSC modulation frequency
> + * @ssc_modfreq_mant_mask: mask of the mantissa component in @ssc_modfreq_reg
> + * @ssc_modfreq_exp_mask: mask of the exponent component in @ssc_modfreq_reg
> + * @ssc_enable_mask: mask of the DPLL SSC enable bit in @control_reg
> + * @ssc_downspread_mask: mask of the DPLL SSC low frequency only bit in
> + *                       @control_reg
> + * @ssc_modfreq: the DPLL SSC frequency modulation in kHz
> + * @ssc_deltam: the DPLL SSC frequency spreading in permille (10th of percent)
> + * @ssc_downspread: require the only low frequency spread of the DPLL in SSC
> + *                   mode
>    * @flags: DPLL type/features (see below)
>    *
>    * Possible values for @flags:
> @@ -110,6 +121,17 @@ struct dpll_data {
>   	u8			auto_recal_bit;
>   	u8			recal_en_bit;
>   	u8			recal_st_bit;
> +	struct clk_omap_reg	ssc_deltam_reg;
> +	struct clk_omap_reg	ssc_modfreq_reg;
> +	u32			ssc_deltam_int_mask;
> +	u32			ssc_deltam_frac_mask;
> +	u32			ssc_modfreq_mant_mask;
> +	u32			ssc_modfreq_exp_mask;
> +	u32                     ssc_enable_mask;
> +	u32                     ssc_downspread_mask;
> +	u32                     ssc_modfreq;
> +	u32                     ssc_deltam;
> +	bool                    ssc_downspread;
>   	u8			flags;
>   };
>   
> 


      reply index

Thread overview: 6+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-04-18 14:56 [PATCH v5 0/5] clk: ti: add am33xx " Dario Binacchi
2021-04-18 14:56 ` [PATCH v5 1/5] clk: ti: fix typo in routine description Dario Binacchi
2021-04-18 14:56 ` [PATCH v5 3/5] ARM: dts: am33xx-clocks: add spread spectrum support Dario Binacchi
2021-04-18 14:56 ` [PATCH v5 4/5] ARM: dts: am43xx-clocks: " Dario Binacchi
2021-04-18 14:56 ` [PATCH v5 5/5] clk: ti: add am33xx/am43xx spread spectrum clock support Dario Binacchi
2021-04-19 11:26   ` Tero Kristo [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3e6472c2-5256-0248-6a09-32a59a74832e@kernel.org \
    --to=kristo@kernel.org \
    --cc=dariobin@libero.it \
    --cc=grygorii.strashko@ti.com \
    --cc=lee.jones@linaro.org \
    --cc=linux-clk@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=mturquette@baylibre.com \
    --cc=sboyd@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-OMAP Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-omap/0 linux-omap/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-omap linux-omap/ https://lore.kernel.org/linux-omap \
		linux-omap@vger.kernel.org
	public-inbox-index linux-omap

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-omap


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git