From: Jon Hunter <jon-hunter@ti.com>
To: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: "Cousson, Benoit" <b-cousson@ti.com>,
Stephen Warren <swarren@nvidia.com>,
Rob Herring <robherring2@gmail.com>,
Kevin Hilman <khilman@deeprootsystems.com>,
"devicetree-discuss@lists.ozlabs.org"
<devicetree-discuss@lists.ozlabs.org>,
"linux-omap@vger.kernel.org" <linux-omap@vger.kernel.org>,
Tarun Kanti DebBarma <tarun.kanti@ti.com>,
"linux-arm-kernel@lists.infradead.org"
<linux-arm-kernel@lists.infradead.org>,
Grant Likely <grant.likely@secretlab.ca>
Subject: Re: [PATCH 3/5] gpio/omap: Add DT support to GPIO driver
Date: Tue, 26 Feb 2013 16:40:26 -0600 [thread overview]
Message-ID: <512D39DA.7020306@ti.com> (raw)
In-Reply-To: <CAAwP0s0cB368R2mtbJpTZJreR-5GSRLfxC+8DJLo5nw3_OwBuA@mail.gmail.com>
On 02/26/2013 04:01 AM, Javier Martinez Canillas wrote:
[snip]
> I was wondering if the level/edge settings for gpios is working on OMAP.
>
> I'm adding DT support for an SMSC911x ethernet chip connected to the
> GPMC for an OMAP3 SoC based board.
>
> In the smsc911x driver probe function (smsc911x_drv_probe() in
> drivers/net/ethernet/smsc/smsc911x.c), a call to request_irq() with
> the flag IRQF_TRIGGER_LOW is needed because of the wiring on my board.
>
> Reading the gpio-omap.txt documentation it says that #interrupt-cells
> should be <2> and that a value of 8 is "active low level-sensitive".
>
> So I tried this:
>
> &gpmc {
> ethernet@5,0 {
> pinctrl-names = "default";
> pinctrl-0 = <&smsc911x_pins>;
> compatible = "smsc,lan9221", "smsc,lan9115";
> reg = <5 0 0xff>; /* CS5 */
> interrupt-parent = <&gpio6>;
> interrupts = <16 8>; /* gpio line 176 */
> interrupt-names = "smsc911x irq";
> vmmc-supply = <&vddvario>;
> vmmc_aux-supply = <&vdd33a>;
> reg-io-width = <4>;
>
> smsc,save-mac-address;
> };
> };
Are you requesting the gpio anywhere? If not then this is not going to
work as-is. This was discussed fairly recently [1] and the conclusion
was that the gpio needs to be requested before we can use as an interrupt.
I have not seen your latest smsc code for omap, but when you are
requesting the gpmc chip-select you should also request the gpio.
> But in the smsc911x probe function:
>
> irq_res->flags & IRQF_TRIGGER_MASK;
>
> returns 0 which means that no trigger flags where set.
>
> I took a look to the GPIOs device node definition on omap{3,4,5}.dtsi
> and all look like this:
>
> e.g from omap3.dtsi:
>
> gpio6: gpio@49058000 {
> compatible = "ti,omap3-gpio";
> ti,hwmods = "gpio6";
> gpio-controller;
> #gpio-cells = <2>;
> interrupt-controller;
> #interrupt-cells = <1>;
> };
>
> So, even when the documentation says that all the GPIO device nodes in
> OMAP2+ should use a #interrupt-cells property value of <2>, they are
> only using <1>. Changing that value to 2 makes hangs the kernel and it
> does not boot.
I will need to take a look at that. Is your code available anywhere so I
can test?
Cheers
Jon
[1] http://permalink.gmane.org/gmane.linux.ports.arm.omap/92192
next prev parent reply other threads:[~2013-02-26 22:40 UTC|newest]
Thread overview: 95+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-02-15 16:04 [PATCH 0/5] gpio/omap: Cleanup and adaptation to Device Tree Benoit Cousson
2012-02-15 16:04 ` [PATCH 1/5] gpio/omap: Remove bank->id information and misc cleanup Benoit Cousson
2012-02-16 5:53 ` DebBarma, Tarun Kanti
2012-02-16 9:33 ` Cousson, Benoit
2012-02-15 16:04 ` [PATCH 2/5] gpio/omap: Use devm_ API and add request_mem_region Benoit Cousson
2012-02-16 5:41 ` DebBarma, Tarun Kanti
2012-02-16 6:35 ` Grant Likely
2012-02-16 7:11 ` DebBarma, Tarun Kanti
2012-02-16 6:37 ` Shubhrajyoti
2012-02-16 8:56 ` Cousson, Benoit
2012-02-15 16:04 ` [PATCH 3/5] gpio/omap: Add DT support to GPIO driver Benoit Cousson
2012-02-22 14:23 ` Rob Herring
2012-02-22 14:31 ` Cousson, Benoit
2012-02-22 17:23 ` Rob Herring
2012-02-22 18:29 ` Stephen Warren
2012-02-24 15:30 ` Cousson, Benoit
2013-02-26 10:01 ` Javier Martinez Canillas
2013-02-26 16:33 ` Stephen Warren
2013-02-26 22:40 ` Jon Hunter [this message]
2013-02-26 22:44 ` Stephen Warren
2013-02-26 23:01 ` Jon Hunter
2013-02-26 23:06 ` Stephen Warren
2013-02-26 23:45 ` Jon Hunter
2013-02-27 0:13 ` Stephen Warren
2013-02-27 1:07 ` Jon Hunter
2013-02-27 3:57 ` Javier Martinez Canillas
2013-02-27 17:50 ` Stephen Warren
2013-02-27 20:05 ` Javier Martinez Canillas
2013-02-27 23:16 ` Jon Hunter
2013-02-28 12:17 ` Javier Martinez Canillas
2013-02-28 20:49 ` Jon Hunter
[not found] ` <512D3EC2.6050408-l0cyMroinI0@public.gmane.org>
2013-03-02 20:05 ` Grant Likely
2013-03-07 23:14 ` Jon Hunter
2013-03-15 11:21 ` Javier Martinez Canillas
2013-03-22 8:10 ` Linus Walleij
2013-03-22 15:33 ` Stephen Warren
2013-03-22 22:52 ` Jon Hunter
2013-03-27 13:52 ` Linus Walleij
2013-03-27 16:09 ` Stephen Warren
2013-03-27 20:55 ` Linus Walleij
2013-03-29 17:01 ` Stephen Warren
2013-04-10 18:12 ` Linus Walleij
2013-04-10 20:29 ` Stephen Warren
2013-04-10 21:28 ` Linus Walleij
2013-04-11 20:30 ` Stephen Warren
2013-04-11 22:16 ` Linus Walleij
2013-04-11 22:47 ` Stephen Warren
2013-04-14 1:35 ` Javier Martinez Canillas
2013-04-14 20:53 ` Linus Walleij
2013-04-15 11:25 ` Javier Martinez Canillas
2013-04-15 16:58 ` Stephen Warren
[not found] ` <516C73C6.5050409@ti.co m>
2013-04-15 21:40 ` Jon Hunter
2013-04-15 21:44 ` Jon Hunter
2013-04-15 22:16 ` Stephen Warren
2013-04-15 23:04 ` Jon Hunter
2013-04-16 18:40 ` Stephen Warren
2013-04-16 19:27 ` Jon Hunter
2013-04-16 21:57 ` Jon Hunter
2013-04-16 22:11 ` Stephen Warren
2013-04-16 23:14 ` Jon Hunter
2013-04-17 0:41 ` Javier Martinez Canillas
2013-04-17 2:00 ` Jon Hunter
2013-04-17 7:55 ` Javier Martinez Canillas
[not found] ` <CAAwP0s2M2pnSydyDvh_rejFO=w8bCo4WE5PkxrYuk0HQDixc-Q-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2013-04-17 13:25 ` Jon Hunter
2013-04-17 13:42 ` Javier Martinez Canillas
[not found] ` <CAAwP0s2DsJAWuXWvPAkzCT0T0AG_OvMEw2sADW6LqSi1Ofd_Zw-JsoAwUIsXosN+BqQ9rBEUg@public.gmane.org>
2013-04-17 13:52 ` Jon Hunter
2013-04-17 14:21 ` Javier Martinez Canillas
2013-04-17 16:18 ` Javier Martinez Canillas
2013-04-26 7:31 ` Linus Walleij
2013-04-26 21:31 ` Jon Hunter
2013-06-11 21:25 ` Grant Likely
2013-06-12 9:43 ` Linus Walleij
2013-04-17 15:41 ` Stephen Warren
2013-04-26 7:27 ` Linus Walleij
2013-04-26 21:25 ` Jon Hunter
[not found] ` <517AF0C1.60009-l0cyMroinI0@public.gmane.org>
2013-05-03 14:35 ` Linus Walleij
2013-04-26 7:11 ` Linus Walleij
2013-04-26 6:59 ` Linus Walleij
2013-04-15 16:53 ` Stephen Warren
2013-04-15 20:00 ` Jon Hunter
2013-04-11 22:49 ` Javier Martinez Canillas
2013-04-11 22:51 ` Stephen Warren
2013-04-10 21:44 ` Arnd Bergmann
2013-02-27 3:33 ` Javier Martinez Canillas
2013-02-27 17:47 ` Stephen Warren
2013-02-27 20:00 ` Javier Martinez Canillas
2013-02-26 23:08 ` Jon Hunter
2013-02-27 3:47 ` Javier Martinez Canillas
2013-02-27 20:13 ` Jon Hunter
2013-02-27 23:41 ` Linus Walleij
2013-02-28 13:04 ` Benoit Cousson
2013-03-01 0:09 ` Linus Walleij
2013-03-01 0:42 ` Jon Hunter
2012-02-15 16:04 ` [PATCH 4/5] arm/dts: OMAP4: Add gpio nodes Benoit Cousson
2012-02-15 16:04 ` [PATCH 5/5] arm/dts: OMAP3: " Benoit Cousson
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=512D39DA.7020306@ti.com \
--to=jon-hunter@ti.com \
--cc=b-cousson@ti.com \
--cc=devicetree-discuss@lists.ozlabs.org \
--cc=grant.likely@secretlab.ca \
--cc=khilman@deeprootsystems.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-omap@vger.kernel.org \
--cc=martinez.javier@gmail.com \
--cc=robherring2@gmail.com \
--cc=swarren@nvidia.com \
--cc=tarun.kanti@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).