Linux-OMAP Archive on lore.kernel.org
 help / color / Atom feed
From: Suman Anna <s-anna@ti.com>
To: Mathieu Poirier <mathieu.poirier@linaro.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>,
	Grzegorz Jaszczyk <grzegorz.jaszczyk@linaro.org>,
	Jan Kiszka <jan.kiszka@siemens.com>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Lokesh Vutla <lokeshvutla@ti.com>,
	<linux-remoteproc@vger.kernel.org>, <linux-omap@vger.kernel.org>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 3/3] remoteproc: pru: Fix and cleanup firmware interrupt mapping logic
Date: Wed, 7 Apr 2021 09:34:16 -0500
Message-ID: <98a3bc08-5740-3e2c-0ed6-0381cb20283d@ti.com> (raw)
In-Reply-To: <20210406234747.GC330882@xps15>

Hi Mathieu,

On 4/6/21 6:47 PM, Mathieu Poirier wrote:
> On Tue, Mar 23, 2021 at 05:38:39PM -0500, Suman Anna wrote:
>> The PRU firmware interrupt mappings are configured and unconfigured in
>> .start() and .stop() callbacks respectively using the variables 'evt_count'
>> and a 'mapped_irq' pointer. These variables are modified only during these
>> callbacks but are not re-initialized/reset properly during unwind or
>> failure paths. These stale values caused a kernel crash while stopping a
>> PRU remoteproc running a different firmware with no events on a subsequent
>> run after a previous run that was running a firmware with events.
>>
>> Fix this crash by ensuring that the evt_count is 0 and the mapped_irq
>> pointer is set to NULL in pru_dispose_irq_mapping(). Also, reset these
>> variables properly during any failures in the .start() callback. While
>> at this, the pru_dispose_irq_mapping() callsites are all made to look
>> the same, moving any conditional logic to inside the function.
>>
>> Fixes: c75c9fdac66e ("remoteproc: pru: Add support for PRU specific interrupt configuration")
>> Reported-by: Vignesh Raghavendra <vigneshr@ti.com>
>> Signed-off-by: Suman Anna <s-anna@ti.com>
>> ---
>>  drivers/remoteproc/pru_rproc.c | 12 +++++++++---
>>  1 file changed, 9 insertions(+), 3 deletions(-)
>>
>> diff --git a/drivers/remoteproc/pru_rproc.c b/drivers/remoteproc/pru_rproc.c
>> index 87b43976c51b..5df19acb90ed 100644
>> --- a/drivers/remoteproc/pru_rproc.c
>> +++ b/drivers/remoteproc/pru_rproc.c
>> @@ -266,12 +266,17 @@ static void pru_rproc_create_debug_entries(struct rproc *rproc)
>>  
>>  static void pru_dispose_irq_mapping(struct pru_rproc *pru)
>>  {
>> -	while (pru->evt_count--) {
>> +	if (!pru->mapped_irq)
>> +		return;
>> +
>> +	while (pru->evt_count) {
>> +		pru->evt_count--;
>>  		if (pru->mapped_irq[pru->evt_count] > 0)
>>  			irq_dispose_mapping(pru->mapped_irq[pru->evt_count]);
>>  	}
>>  
>>  	kfree(pru->mapped_irq);
>> +	pru->mapped_irq = NULL;
>>  }
>>  
>>  /*
>> @@ -324,6 +329,8 @@ static int pru_handle_intrmap(struct rproc *rproc)
>>  	of_node_put(parent);
>>  	if (!irq_parent) {
>>  		kfree(pru->mapped_irq);
>> +		pru->mapped_irq = NULL;
>> +		pru->evt_count = 0;
> 
> Patch 1/3 introduced a check on @parent that doesn't free pru->mapped_irq.  I
> would also expect that error path to do the same has what is done here.  And
> looking further up I see the error path for !pru->mapped_irq doesn't set
> pru->evt_count to zero.

Good catch, thank you. I will fix these up in v2.

regards
Suman

> 
> Thanks,
> Mathieu
> 
>>  		return -ENODEV;
>>  	}
>>  
>> @@ -398,8 +405,7 @@ static int pru_rproc_stop(struct rproc *rproc)
>>  	pru_control_write_reg(pru, PRU_CTRL_CTRL, val);
>>  
>>  	/* dispose irq mapping - new firmware can provide new mapping */
>> -	if (pru->mapped_irq)
>> -		pru_dispose_irq_mapping(pru);
>> +	pru_dispose_irq_mapping(pru);
>>  
>>  	return 0;
>>  }
>> -- 
>> 2.30.1
>>


      reply index

Thread overview: 9+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-23 22:38 [PATCH 0/3] PRU firmware event/interrupt mapping fixes Suman Anna
2021-03-23 22:38 ` [PATCH 1/3] remoteproc: pru: Fixup interrupt-parent logic for fw events Suman Anna
2021-04-06 23:28   ` Mathieu Poirier
2021-04-07 14:32     ` Suman Anna
2021-03-23 22:38 ` [PATCH 2/3] remoteproc: pru: Fix wrong success return value " Suman Anna
2021-04-06 23:33   ` Mathieu Poirier
2021-03-23 22:38 ` [PATCH 3/3] remoteproc: pru: Fix and cleanup firmware interrupt mapping logic Suman Anna
2021-04-06 23:47   ` Mathieu Poirier
2021-04-07 14:34     ` Suman Anna [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=98a3bc08-5740-3e2c-0ed6-0381cb20283d@ti.com \
    --to=s-anna@ti.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=grzegorz.jaszczyk@linaro.org \
    --cc=jan.kiszka@siemens.com \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-omap@vger.kernel.org \
    --cc=linux-remoteproc@vger.kernel.org \
    --cc=lokeshvutla@ti.com \
    --cc=mathieu.poirier@linaro.org \
    --cc=vigneshr@ti.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-OMAP Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-omap/0 linux-omap/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-omap linux-omap/ https://lore.kernel.org/linux-omap \
		linux-omap@vger.kernel.org
	public-inbox-index linux-omap

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-omap


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git