From: Manikanta Maddireddy <mmaddireddy@nvidia.com>
To: <thierry.reding@gmail.com>, <bhelgaas@google.com>,
<robh+dt@kernel.org>, <mark.rutland@arm.com>,
<jonathanh@nvidia.com>, <lorenzo.pieralisi@arm.com>,
<vidyas@nvidia.com>
Cc: <linux-tegra@vger.kernel.org>, <linux-pci@vger.kernel.org>,
<devicetree@vger.kernel.org>,
Manikanta Maddireddy <mmaddireddy@nvidia.com>
Subject: [PATCH V4 25/28] PCI: tegra: Put PEX CLK & BIAS pads in DPD mode
Date: Thu, 16 May 2019 11:23:04 +0530 [thread overview]
Message-ID: <20190516055307.25737-26-mmaddireddy@nvidia.com> (raw)
In-Reply-To: <20190516055307.25737-1-mmaddireddy@nvidia.com>
In Tegra210 AFI design has clamp value for the BIAS pad as 0, which keeps
the bias pad in non power down mode. This is leading to power consumption
of 2 mW in BIAS pad, even if the PCIe partition is powergated. To avoid
unnecessary power consumption, put PEX CLK & BIAS pads in deep power down
mode when PCIe partition is power gated.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
Acked-by: Thierry Reding <treding@nvidia.com>
---
V4: No change
V3: No change
V2: Using standard pinctrl functions to apply default and idle states
drivers/pci/controller/pci-tegra.c | 13 ++++++++++++-
1 file changed, 12 insertions(+), 1 deletion(-)
diff --git a/drivers/pci/controller/pci-tegra.c b/drivers/pci/controller/pci-tegra.c
index 33f4dfab9e35..06b99fcbf382 100644
--- a/drivers/pci/controller/pci-tegra.c
+++ b/drivers/pci/controller/pci-tegra.c
@@ -30,6 +30,7 @@
#include <linux/of_platform.h>
#include <linux/pci.h>
#include <linux/phy/phy.h>
+#include <linux/pinctrl/consumer.h>
#include <linux/platform_device.h>
#include <linux/reset.h>
#include <linux/sizes.h>
@@ -2875,6 +2876,7 @@ static int __maybe_unused tegra_pcie_pm_suspend(struct device *dev)
if (IS_ENABLED(CONFIG_PCI_MSI))
tegra_pcie_disable_msi(pcie);
+ pinctrl_pm_select_idle_state(dev);
tegra_pcie_power_off(pcie);
return 0;
@@ -2890,6 +2892,13 @@ static int __maybe_unused tegra_pcie_pm_resume(struct device *dev)
dev_err(dev, "tegra pcie power on fail: %d\n", err);
return err;
}
+
+ err = pinctrl_pm_select_default_state(dev);
+ if (err < 0) {
+ dev_err(dev, "failed to disable PCIe IO DPD: %d\n", err);
+ goto poweroff;
+ }
+
tegra_pcie_enable_controller(pcie);
tegra_pcie_setup_translations(pcie);
@@ -2899,7 +2908,7 @@ static int __maybe_unused tegra_pcie_pm_resume(struct device *dev)
err = clk_prepare_enable(pcie->pex_clk);
if (err) {
dev_err(dev, "failed to enable PEX clock: %d\n", err);
- goto poweroff;
+ goto pex_dpd_enable;
}
reset_control_deassert(pcie->pex_rst);
@@ -2920,6 +2929,8 @@ static int __maybe_unused tegra_pcie_pm_resume(struct device *dev)
disable_pex_clk:
reset_control_assert(pcie->pex_rst);
clk_disable_unprepare(pcie->pex_clk);
+pex_dpd_enable:
+ pinctrl_pm_select_idle_state(dev);
poweroff:
tegra_pcie_power_off(pcie);
--
2.17.1
next prev parent reply other threads:[~2019-05-16 5:54 UTC|newest]
Thread overview: 72+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-16 5:52 [PATCH V4 00/28] Enable Tegra PCIe root port features Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 01/28] soc/tegra: pmc: Export tegra_powergate_power_on() Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 02/28] PCI: tegra: Handle failure cases in tegra_pcie_power_on() Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 03/28] PCI: tegra: Rearrange Tegra PCIe driver functions Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 04/28] PCI: tegra: Mask AFI_INTR in runtime suspend Manikanta Maddireddy
2019-06-04 13:08 ` Thierry Reding
2019-05-16 5:52 ` [PATCH V4 05/28] PCI: tegra: Fix PCIe host power up sequence Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 06/28] PCI: tegra: Add PCIe Gen2 link speed support Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 07/28] PCI: tegra: Advertise PCIe Advanced Error Reporting (AER) capability Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 08/28] PCI: tegra: Program UPHY electrical settings for Tegra210 Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 09/28] PCI: tegra: Enable opportunistic UpdateFC and ACK Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 10/28] PCI: tegra: Disable AFI dynamic clock gating Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 11/28] PCI: tegra: Process pending DLL transactions before entering L1 or L2 Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 12/28] PCI: tegra: Enable PCIe xclk clock clamping Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 13/28] PCI: tegra: Increase the deskew retry time Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 14/28] PCI: tegra: Add SW fixup for RAW violations Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 15/28] PCI: tegra: Update flow control timer frequency in Tegra210 Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 16/28] PCI: tegra: Set target speed as Gen1 before starting LTSSM Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 17/28] PCI: tegra: Fix PLLE power down issue due to CLKREQ# signal Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 18/28] PCI: tegra: Program AFI_CACHE* registers only for Tegra20 Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 19/28] PCI: tegra: Change PRSNT_SENSE IRQ log to debug Manikanta Maddireddy
2019-05-16 5:52 ` [PATCH V4 20/28] PCI: tegra: Use legacy IRQ for port service drivers Manikanta Maddireddy
2019-05-20 20:37 ` Bjorn Helgaas
2019-05-21 9:07 ` Manikanta Maddireddy
2019-05-16 5:53 ` [PATCH V4 21/28] PCI: tegra: Add AFI_PEX2_CTRL reg offset as part of soc struct Manikanta Maddireddy
2019-05-16 5:53 ` [PATCH V4 22/28] PCI: tegra: Access endpoint config only if PCIe link is up Manikanta Maddireddy
2019-06-04 13:14 ` Thierry Reding
2019-06-04 14:10 ` Manikanta Maddireddy
2019-06-10 4:38 ` Manikanta Maddireddy
2019-06-13 14:39 ` Lorenzo Pieralisi
2019-06-13 15:42 ` Thierry Reding
2019-06-17 10:01 ` Manikanta Maddireddy
2019-06-17 11:47 ` Thierry Reding
2019-06-17 19:30 ` Bjorn Helgaas
2019-06-18 5:36 ` Manikanta Maddireddy
2019-06-18 10:49 ` Thierry Reding
2019-06-18 12:32 ` Johannes Berg
2019-06-18 13:40 ` Thierry Reding
2019-06-18 14:48 ` Johannes Berg
2019-06-19 13:38 ` Bjorn Helgaas
2019-06-19 13:40 ` Johannes Berg
2019-05-16 5:53 ` [PATCH V4 23/28] dt-bindings: pci: tegra: Document PCIe DPD pinctrl optional prop Manikanta Maddireddy
2019-05-16 5:53 ` [PATCH V4 24/28] arm64: tegra: Add PEX DPD states as pinctrl properties Manikanta Maddireddy
2019-05-16 5:53 ` Manikanta Maddireddy [this message]
2019-05-16 5:53 ` [PATCH V4 26/28] PCI: Add DT binding for "reset-gpios" property Manikanta Maddireddy
2019-06-17 11:30 ` Thierry Reding
2019-06-17 11:38 ` Manikanta Maddireddy
2019-06-17 11:48 ` Thierry Reding
2019-05-16 5:53 ` [PATCH V4 27/28] PCI: tegra: Add support for GPIO based PERST# Manikanta Maddireddy
2019-06-04 13:22 ` Thierry Reding
2019-06-13 15:24 ` Lorenzo Pieralisi
2019-06-14 10:37 ` Manikanta Maddireddy
2019-06-14 14:32 ` Lorenzo Pieralisi
2019-06-14 14:38 ` Manikanta Maddireddy
2019-06-14 14:50 ` Lorenzo Pieralisi
2019-06-14 14:56 ` Manikanta Maddireddy
2019-06-14 15:23 ` Thierry Reding
2019-06-14 15:59 ` Lorenzo Pieralisi
2019-06-14 16:30 ` Manikanta Maddireddy
2019-06-14 16:53 ` Lorenzo Pieralisi
2019-06-14 17:23 ` Manikanta Maddireddy
2019-06-17 9:48 ` Lorenzo Pieralisi
2019-06-17 10:27 ` Manikanta Maddireddy
2019-06-17 10:39 ` Lorenzo Pieralisi
2019-06-17 11:29 ` Thierry Reding
2019-06-17 11:26 ` Thierry Reding
2019-05-16 5:53 ` [PATCH V4 28/28] PCI: tegra: Change link retry log level to debug Manikanta Maddireddy
2019-06-04 13:22 ` Thierry Reding
2019-05-16 13:12 ` [PATCH V4 00/28] Enable Tegra PCIe root port features Bjorn Helgaas
2019-05-17 8:38 ` Manikanta Maddireddy
2019-06-10 4:45 ` Manikanta Maddireddy
2019-06-10 17:33 ` Lorenzo Pieralisi
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190516055307.25737-26-mmaddireddy@nvidia.com \
--to=mmaddireddy@nvidia.com \
--cc=bhelgaas@google.com \
--cc=devicetree@vger.kernel.org \
--cc=jonathanh@nvidia.com \
--cc=linux-pci@vger.kernel.org \
--cc=linux-tegra@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
--cc=thierry.reding@gmail.com \
--cc=vidyas@nvidia.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).