On Fri, May 17, 2019 at 06:08:34PM +0530, Vidya Sagar wrote:
> Remove multiple write enable and disable sequences of dbi registers as
> Tegra194 implements writes to BAR-0 register (offset: 0x10) controlled by
> DBI write-lock enable bit thereby not allowing any further writes to BAR-0
> register in config space to take place. Hence enabling write permission at
> the start of function and disabling the same only towards the end.
> 
> Signed-off-by: Vidya Sagar <vidyas@nvidia.com>
> ---
> Changes since [v6]:
> * None
> 
> Changes since [v5]:
> * Moved write enable to the beginning of the API and write disable to the end
> 
> Changes since [v4]:
> * None
> 
> Changes since [v3]:
> * None
> 
> Changes since [v2]:
> * None
> 
> Changes since [v1]:
> * None
> 
>  drivers/pci/controller/dwc/pcie-designware-host.c | 14 ++++++++------
>  1 file changed, 8 insertions(+), 6 deletions(-)

Looks good to me:

Reviewed-by: Thierry Reding <treding@nvidia.com>

Thierry

> 
> diff --git a/drivers/pci/controller/dwc/pcie-designware-host.c b/drivers/pci/controller/dwc/pcie-designware-host.c
> index f93252d0da5b..d3156446ff27 100644
> --- a/drivers/pci/controller/dwc/pcie-designware-host.c
> +++ b/drivers/pci/controller/dwc/pcie-designware-host.c
> @@ -628,6 +628,12 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
>  	u32 val, ctrl, num_ctrls;
>  	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
>  
> +	/*
> +	 * Enable DBI read-only registers for writing/updating configuration.
> +	 * Write permission gets disabled towards the end of this function.
> +	 */
> +	dw_pcie_dbi_ro_wr_en(pci);
> +
>  	dw_pcie_setup(pci);
>  
>  	if (!pp->ops->msi_host_init) {
> @@ -650,12 +656,10 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
>  	dw_pcie_writel_dbi(pci, PCI_BASE_ADDRESS_1, 0x00000000);
>  
>  	/* Setup interrupt pins */
> -	dw_pcie_dbi_ro_wr_en(pci);
>  	val = dw_pcie_readl_dbi(pci, PCI_INTERRUPT_LINE);
>  	val &= 0xffff00ff;
>  	val |= 0x00000100;
>  	dw_pcie_writel_dbi(pci, PCI_INTERRUPT_LINE, val);
> -	dw_pcie_dbi_ro_wr_dis(pci);
>  
>  	/* Setup bus numbers */
>  	val = dw_pcie_readl_dbi(pci, PCI_PRIMARY_BUS);
> @@ -687,15 +691,13 @@ void dw_pcie_setup_rc(struct pcie_port *pp)
>  
>  	dw_pcie_wr_own_conf(pp, PCI_BASE_ADDRESS_0, 4, 0);
>  
> -	/* Enable write permission for the DBI read-only register */
> -	dw_pcie_dbi_ro_wr_en(pci);
>  	/* Program correct class for RC */
>  	dw_pcie_wr_own_conf(pp, PCI_CLASS_DEVICE, 2, PCI_CLASS_BRIDGE_PCI);
> -	/* Better disable write permission right after the update */
> -	dw_pcie_dbi_ro_wr_dis(pci);
>  
>  	dw_pcie_rd_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, &val);
>  	val |= PORT_LOGIC_SPEED_CHANGE;
>  	dw_pcie_wr_own_conf(pp, PCIE_LINK_WIDTH_SPEED_CONTROL, 4, val);
> +
> +	dw_pcie_dbi_ro_wr_dis(pci);
>  }
>  EXPORT_SYMBOL_GPL(dw_pcie_setup_rc);
> -- 
> 2.17.1
>