Linux-PCI Archive on lore.kernel.org
 help / color / Atom feed
From: Sean V Kelley <sean.v.kelley@linux.intel.com>
To: tglx@linutronix.de, bhelgaas@google.com, corbet@lwn.net,
	mingo@redhat.com, bp@alien8.de
Cc: x86@kernel.org, linux-pci@vger.kernel.org,
	linux-kernel@vger.kernel.org, linux-doc@vger.kernel.org,
	kar.hin.ong@ni.com, sassmann@kpanic.de,
	Sean V Kelley <sean.v.kelley@linux.intel.com>
Subject: [PATCH 2/2] Documentation:PCI: Add background on Boot Interrupts
Date: Fri, 14 Feb 2020 13:33:13 -0800
Message-ID: <20200214213313.66622-3-sean.v.kelley@linux.intel.com> (raw)
In-Reply-To: <20200214213313.66622-1-sean.v.kelley@linux.intel.com>

Improve understanding of the PCI quirks for this legacy PCI interrupt
behavior to the benefit of developers and users alike.

Signed-off-by: Sean V Kelley <sean.v.kelley@linux.intel.com>
---
 Documentation/PCI/boot-interrupts.rst | 153 ++++++++++++++++++++++++++
 Documentation/PCI/index.rst           |   1 +
 2 files changed, 154 insertions(+)
 create mode 100644 Documentation/PCI/boot-interrupts.rst

diff --git a/Documentation/PCI/boot-interrupts.rst b/Documentation/PCI/boot-interrupts.rst
new file mode 100644
index 000000000000..632c080994fc
--- /dev/null
+++ b/Documentation/PCI/boot-interrupts.rst
@@ -0,0 +1,153 @@
+.. SPDX-License-Identifier: GPL-2.0
+
+===============
+Boot Interrupts
+===============
+
+:Author: - Sean V Kelley <sean.v.kelley@linux.intel.com>
+
+Overview
+========
+
+On PCI Express, interrupts are represented with either MSI or inbound interrupt
+messages (Assert_INTx/Deassert_INTx). The integrated IO-APIC in a given Core
+IO converts the legacy interrupt messages from PCI Express to MSI interrupts.
+If the IO-APIC is disabled (via the mask bits in the IO-APIC table entries),
+the messages are routed to the legacy PCH. This in-band interrupt mechanism was
+traditionally necessary for systems that did not support the IO-APIC and for
+boot. Intel in the past has used the term "boot interrupts" to describe this
+mechanism. Further, the PCI Express protocol describes this in-band legacy
+wire-interrupt INTx mechanism for I/O devices to signal PCI-style level
+interrupts. The subsequent paragraphs describe problems with the Core IO
+handling of INTx message routing to the PCH and mitigation within BIOS and
+the OS.
+
+
+Problem
+=======
+
+When in-band legacy INTx messages are forwarded to the PCH, they in turn
+trigger a new interrupt for which the OS likely lacks a handler. When an
+interrupt goes unhandled over time, they are tracked by the Linux kernel
+as Spurious Interrupts. The IRQ will be disabled by the Linux kernel after
+it reaches a specific count with the error "nobody cared". This disabled
+IRQ now prevents valid usage by an existing interrupt which may happen to
+share the IRQ line.
+
+irq 19: nobody cared (try booting with the "irqpoll" option)
+CPU: 0 PID: 2988 Comm: irq/34-nipalk Tainted: 4.14.87-rt49-02410-g4a640ec-dirty #1
+Hardware name: National Instruments NI PXIe-8880/NI PXIe-8880, BIOS 2.1.5f1 01/09/2020
+Call Trace:
+<IRQ>
+ ? dump_stack+0x46/0x5e
+ ? __report_bad_irq+0x2e/0xb0
+ ? note_interrupt+0x242/0x290
+ ? nNIKAL100_memoryRead16+0x8/0x10 [nikal]
+ ? handle_irq_event_percpu+0x55/0x70
+ ? handle_irq_event+0x4f/0x80
+ ? handle_fasteoi_irq+0x81/0x180
+ ? handle_irq+0x1c/0x30
+ ? do_IRQ+0x41/0xd0
+ ? common_interrupt+0x84/0x84
+</IRQ>
+
+handlers:
+irq_default_primary_handler threaded usb_hcd_irq
+Disabling IRQ #19
+
+
+Conditions
+==========
+
+The use of threaded interrupts is the most likely condition to trigger this
+problem today. Threaded interrupts may not be reenabled after the IRQ handler
+wakes. These "one shot" conditions mean that the threaded interrupt needs to
+keep the interrupt line masked until the threaded handler has run. Especially
+when dealing with high data rate interrupts, the thread needs to run to completion
+otherwise some handlers will end up in stack overflows since the interrupt
+of the issuing device is still active.
+
+Affected Chipsets
+=================
+
+The legacy interrupt forwarding mechansim exists today in a number of devices
+including but not limited to chipsets from AMD/ATI, Broadcom, and Intel. Changes
+made through the mitigations below have been applied to drivers/pci/quirks.c
+
+Starting with ICX there are no longer any IO-APICs in the Core IO's devices.
+IO-APIC is only in the PCH.  Devices connected to the Core IO's PCIE Root Ports
+will use native MSI/MSI-X mechanisms.
+
+Mitigations
+===========
+
+The mitigations take the form of PCI quirks. The preference has been to first
+identify and make use of a means to disable the routing to the PCH. In such a
+case a quirk to disable boot interrupt generation can be added.[1]
+
+Intel® 6300ESB I/O Controller Hub
+Alternate Base Address Register:
+ BIE: Boot Interrupt Enable
+	0 = Boot interrupt is enabled.
+	1 = Boot interrupt is disabled.
+
+Intel® Sandy Bridge through Sky Lake based Xeon servers:
+Coherent Interface Protocol Interrupt Control
+ dis_intx_route2pch/dis_intx_route2ich/dis_intx_route2dmi2:
+	When this bit is set. Local INTx messages received from the
+	Intel® Quick Data DMA/PCI Express ports are not routed to legacy
+	PCH - they are either converted into MSI via the integrated IO-APIC
+	(if the IO-APIC mask bit is clear in the appropriate entries)
+	or cause no further action (when mask bit is set)
+
+In the absence of a way to directly disable the routing, another approach
+has been to make use of PCI Interrupt pin to INTx routing tables for purposes
+of redirecting the interrupt handler to the rerouted interrupt line by default.
+Therefore, on chipsets where this INTx routing cannot be disabled, the
+Linux kernel will reroute the valid interrupt to its legacy interrupt. This
+redirection of the handler will prevent the occurrence of the spurious
+interrupt detection which would ordinarily disable the IRQ line due to
+excessive unhandled counts.[2]
+
+The config option X86_REROUTE_FOR_BROKEN_BOOT_IRQS exists to enable
+(or disable) the redirection of the interrupt handler to the PCH interrupt
+line. The option can be overridden by either pci=ioapicreroute or
+pci=noioapicreroute.[3]
+
+
+More Documentation
+==================
+
+There is an overview of the legacy interrupt handling mentioned in several
+datasheets (6300ESB and 6700PXH below). While largely the same, it provides
+insight into the evolution of its handling with chipsets.
+
+Example of disabling of the boot interrupt
+------------------------------------------
+
+Intel® 6300ESB I/O Controller Hub (Document # 300641-004US)
+	2.15.2 PCI Express Legacy INTx Support and Boot Interrupt
+	https://www.intel.com/content/dam/doc/datasheet/6300esb-io-controller-hub-datasheet.pdf
+
+Intel® Xeon® Processor E5-1600/2400/2600/4600 v3 Product Families
+Datasheet - Volume 2: Registers (Dcument # 330784-003)
+	6.6.41 cipintrc Coherent Interface Protocol Interrupt Control
+	https://www.intel.com/content/dam/www/public/us/en/documents/datasheets/xeon-e5-v3-datasheet-vol-2.pdf
+
+Example of handler rerouting
+----------------------------
+
+Intel® 6700PXH 64-bit PCI Hub (Document # 302628)
+	2.15.2 PCI Express Legacy INTx Support and Boot Interrupt
+	https://www.intel.com/content/dam/doc/datasheet/6700pxh-64-bit-pci-hub-datasheet.pdf
+
+
+If you have any legacy PCI interrupt questions that aren't answered, email me.
+
+Cheers,
+    Sean V Kelley
+    sean.v.kelley@linux.intel.com
+
+[1] https://lore.kernel.org/lkml/12131949181903-git-send-email-sassmann@suse.de/
+[2] https://lore.kernel.org/lkml/12131949182094-git-send-email-sassmann@suse.de/
+[3] https://lore.kernel.org/lkml/487C8EA7.6020205@suse.de/
diff --git a/Documentation/PCI/index.rst b/Documentation/PCI/index.rst
index 6768305e4c26..8f66feaafd4f 100644
--- a/Documentation/PCI/index.rst
+++ b/Documentation/PCI/index.rst
@@ -16,3 +16,4 @@ Linux PCI Bus Subsystem
    pci-error-recovery
    pcieaer-howto
    endpoint/index
+   boot-interrupts
-- 
2.25.0


  parent reply index

Thread overview: 5+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-02-14 21:33 [PATCH 0/2] Add boot interrupt quirk mechanism for Xeon chipsets Sean V Kelley
2020-02-14 21:33 ` [PATCH 1/2] pci: " Sean V Kelley
2020-02-14 21:33 ` Sean V Kelley [this message]
2020-02-15  9:24 ` [PATCH 0/2] " Thomas Gleixner
2020-02-15  9:26   ` Thomas Gleixner

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200214213313.66622-3-sean.v.kelley@linux.intel.com \
    --to=sean.v.kelley@linux.intel.com \
    --cc=bhelgaas@google.com \
    --cc=bp@alien8.de \
    --cc=corbet@lwn.net \
    --cc=kar.hin.ong@ni.com \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=mingo@redhat.com \
    --cc=sassmann@kpanic.de \
    --cc=tglx@linutronix.de \
    --cc=x86@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-PCI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-pci/0 linux-pci/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-pci linux-pci/ https://lore.kernel.org/linux-pci \
		linux-pci@vger.kernel.org
	public-inbox-index linux-pci

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-pci


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git