Linux-PCI Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v5 0/5] Add PCIe support for SM8250 SoC
@ 2020-10-27 17:00 Manivannan Sadhasivam
  2020-10-27 17:00 ` [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings Manivannan Sadhasivam
                   ` (4 more replies)
  0 siblings, 5 replies; 11+ messages in thread
From: Manivannan Sadhasivam @ 2020-10-27 17:00 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, vkoul, robh
  Cc: svarbanov, bhelgaas, lorenzo.pieralisi, linux-arm-msm, linux-pci,
	linux-kernel, mgautam, devicetree, truong, Manivannan Sadhasivam

Hello,

This series adds PCIe support for Qualcomm SM8250 SoC with relevant PHYs.
There are 3 PCIe instances on this SoC each with different PHYs. The PCIe
controller and PHYs are mostly comaptible with the ones found on SDM845
SoC, hence the old drivers are modified to add the support.

This series has been tested on RB5 board with QCA6391 chipset connected
onboard.

Thanks,
Mani

Changes in v5:

* Added Review tags from Rob
* Cleaned up the bdf to sid patch after discussing with Tony

Changes in v4:

* Fixed an issue with tx_tbl_sec in PHY driver

Changes in v3:

* Rebased on top of phy/next
* Renamed ops_sm8250 to ops_1_9_0 to maintain uniformity

Changes in v2:

* Fixed the PHY and PCIe bindings
* Introduced secondary table in PHY driver to abstract out the common configs.
* Used a more generic way of configuring BDF to SID mapping
* Dropped ATU change in favor of a patch spotted by Rob

Manivannan Sadhasivam (5):
  dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings
  phy: qcom-qmp: Add SM8250 PCIe QMP PHYs
  dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
  PCI: qcom: Add SM8250 SoC support
  PCI: qcom: Add support for configuring BDF to SID mapping for SM8250

 .../devicetree/bindings/pci/qcom,pcie.txt     |   6 +-
 .../devicetree/bindings/phy/qcom,qmp-phy.yaml |   6 +
 drivers/pci/controller/dwc/Kconfig            |   1 +
 drivers/pci/controller/dwc/pcie-qcom.c        |  92 ++++++
 drivers/phy/qualcomm/phy-qcom-qmp.c           | 281 +++++++++++++++++-
 drivers/phy/qualcomm/phy-qcom-qmp.h           |  18 ++
 6 files changed, 398 insertions(+), 6 deletions(-)

-- 
2.17.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings
  2020-10-27 17:00 [PATCH v5 0/5] Add PCIe support for SM8250 SoC Manivannan Sadhasivam
@ 2020-10-27 17:00 ` Manivannan Sadhasivam
  2020-11-16  5:58   ` Vinod Koul
  2020-10-27 17:00 ` [PATCH v5 2/5] phy: qcom-qmp: Add SM8250 PCIe QMP PHYs Manivannan Sadhasivam
                   ` (3 subsequent siblings)
  4 siblings, 1 reply; 11+ messages in thread
From: Manivannan Sadhasivam @ 2020-10-27 17:00 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, vkoul, robh
  Cc: svarbanov, bhelgaas, lorenzo.pieralisi, linux-arm-msm, linux-pci,
	linux-kernel, mgautam, devicetree, truong, Manivannan Sadhasivam

Add the below three PCIe PHYs found in SM8250 to the QMP binding:

QMP GEN3x1 PHY - 1 lane
QMP GEN3x2 PHY - 2 lanes
QMP Modem PHY - 2 lanes

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
index 185cdea9cf81..ec05db374645 100644
--- a/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
+++ b/Documentation/devicetree/bindings/phy/qcom,qmp-phy.yaml
@@ -31,6 +31,9 @@ properties:
       - qcom,sdm845-qmp-usb3-uni-phy
       - qcom,sm8150-qmp-ufs-phy
       - qcom,sm8250-qmp-ufs-phy
+      - qcom,sm8250-qmp-gen3x1-pcie-phy
+      - qcom,sm8250-qmp-gen3x2-pcie-phy
+      - qcom,sm8250-qmp-modem-pcie-phy
 
   reg:
     items:
@@ -259,6 +262,9 @@ allOf:
             enum:
               - qcom,sdm845-qhp-pcie-phy
               - qcom,sdm845-qmp-pcie-phy
+              - qcom,sm8250-qmp-gen3x1-pcie-phy
+              - qcom,sm8250-qmp-gen3x2-pcie-phy
+              - qcom,sm8250-qmp-modem-pcie-phy
     then:
       properties:
         clocks:
-- 
2.17.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v5 2/5] phy: qcom-qmp: Add SM8250 PCIe QMP PHYs
  2020-10-27 17:00 [PATCH v5 0/5] Add PCIe support for SM8250 SoC Manivannan Sadhasivam
  2020-10-27 17:00 ` [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings Manivannan Sadhasivam
@ 2020-10-27 17:00 ` Manivannan Sadhasivam
  2020-11-16  5:58   ` Vinod Koul
  2020-10-27 17:00 ` [PATCH v5 3/5] dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC Manivannan Sadhasivam
                   ` (2 subsequent siblings)
  4 siblings, 1 reply; 11+ messages in thread
From: Manivannan Sadhasivam @ 2020-10-27 17:00 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, vkoul, robh
  Cc: svarbanov, bhelgaas, lorenzo.pieralisi, linux-arm-msm, linux-pci,
	linux-kernel, mgautam, devicetree, truong, Manivannan Sadhasivam

SM8250 has multiple different PHY versions:
QMP GEN3x1 PHY - 1 lane
QMP GEN3x2 PHY - 2 lanes
QMP Modem PHY - 2 lanes

Add support for these with relevant init sequence. In order to abstract
the init sequence, this commit introduces secondary tables which can
be used to factor out the unique sequence for each PHY while the former
tables can have the common sequence.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---
 drivers/phy/qualcomm/phy-qcom-qmp.c | 281 +++++++++++++++++++++++++++-
 drivers/phy/qualcomm/phy-qcom-qmp.h |  18 ++
 2 files changed, 295 insertions(+), 4 deletions(-)

diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.c b/drivers/phy/qualcomm/phy-qcom-qmp.c
index 5d33ad4d06f2..5a941730377f 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.c
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.c
@@ -217,6 +217,13 @@ static const unsigned int sdm845_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_PCS_READY_STATUS]		= 0x160,
 };
 
+static const unsigned int sm8250_pcie_regs_layout[QPHY_LAYOUT_SIZE] = {
+	[QPHY_SW_RESET]			= 0x00,
+	[QPHY_START_CTRL]		= 0x44,
+	[QPHY_PCS_STATUS]		= 0x14,
+	[QPHY_PCS_POWER_DOWN_CONTROL]	= 0x40,
+};
+
 static const unsigned int sm8150_ufsphy_regs_layout[QPHY_LAYOUT_SIZE] = {
 	[QPHY_START_CTRL]		= QPHY_V4_PCS_UFS_PHY_START,
 	[QPHY_PCS_READY_STATUS]		= QPHY_V4_PCS_UFS_READY_STATUS,
@@ -1824,6 +1831,149 @@ static const struct qmp_phy_init_tbl sm8250_usb3_uniphy_pcs_tbl[] = {
 	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x21),
 };
 
+static const struct qmp_phy_init_tbl sm8250_qmp_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_EN_SEL, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CLK_SELECT, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CORECLK_DIV_MODE1, 0x08),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_IVCO, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP_EN, 0x42),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE0, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE2_MODE1, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE1_MODE1, 0xb4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_VCO_TUNE_MAP, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_HSCLK_SEL, 0x11),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE0, 0x82),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE0, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE0, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE0, 0x55),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE0, 0x1a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE0, 0x0a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DEC_START_MODE1, 0x68),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START3_MODE1, 0x02),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START2_MODE1, 0xaa),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_DIV_FRAC_START1_MODE1, 0xab),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP2_MODE1, 0x34),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_LOCK_CMP1_MODE1, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_HSCLK_SEL, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE0, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE0, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE0, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CP_CTRL_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_RCTRL_MODE1, 0x16),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_PLL_CCTRL_MODE1, 0x36),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE0, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE0, 0xca),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE2_MODE1, 0x18),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_BIN_VCOCAL_CMP_CODE1_MODE1, 0xa2),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_EN_CENTER, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER1, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_PER2, 0x01),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE0, 0xde),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1, 0x4c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1, 0x06),
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_CLK_ENABLE1, 0x90),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x1_pcie_serdes_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_COM_SYSCLK_BUF_ENABLE, 0x07),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RCV_DETECT_LVL_2, 0x12),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_LANE_MODE_1, 0x35),
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_RES_CODE_LANE_OFFSET_TX, 0x11),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_FO_GAIN, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_GAIN, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_GM_CAL, 0x1b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_HIGH, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_IDAC_TSETTLE_LOW, 0xc0),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE, 0x30),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_VGA_CAL_CNTRL2, 0x07),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_SO_SATURATION_AND_ENABLE, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_UCDR_PI_CONTROLS, 0x70),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2, 0x0e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3, 0x4a),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4, 0x0f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_CNTRL, 0x03),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_ENABLES, 0x1c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL, 0x1e),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1, 0x17),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_LOW, 0xd4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH, 0x54),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH2, 0xdb),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH3, 0x3b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_10_HIGH4, 0x31),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_LOW, 0x24),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH2, 0xff),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH3, 0x7f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DCC_CTRL1, 0x0c),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH, 0xe4),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH2, 0xec),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH3, 0x3b),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_01_HIGH4, 0x36),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x1_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RCLK_AUXDATA_SEL, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL1, 0x00),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_EN_TIMER, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0x3f),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x14),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x30),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_P2U3_WAKEUP_DLY_TIME_AUXCLK_L, 0x01),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RX_SIGDET_LVL, 0x77),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_RATE_SLEW_CNTRL1, 0x0b),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x1_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG5, 0x12),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_OSC_DTCT_ACTIONS, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L, 0x01),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L, 0x01),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_PRESET_P6_P7_PRE, 0x33),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_PRESET_P10_PRE, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_PRESET_P10_POST, 0x58),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_DRIVE, 0xc1),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x1_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_INT_AUX_CLK_CONFIG1, 0x00),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_EQ_CONFIG2, 0x0f),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x2_pcie_tx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_TX_PI_QEC_CTRL, 0x20),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x2_pcie_rx_tbl[] = {
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL1, 0x04),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_LOW, 0xbf),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_RX_MODE_00_HIGH4, 0x15),
+	QMP_PHY_INIT_CFG(QSERDES_V4_RX_DFE_CTLE_POST_CAL_OFFSET, 0x38),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x2_pcie_pcs_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_REFGEN_REQ_CONFIG1, 0x05),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_EQ_CONFIG2, 0x0f),
+};
+
+static const struct qmp_phy_init_tbl sm8250_qmp_gen3x2_pcie_pcs_misc_tbl[] = {
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG2, 0x0d),
+	QMP_PHY_INIT_CFG(QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG4, 0x07),
+};
+
 /* struct qmp_phy_cfg - per-PHY initialization config */
 struct qmp_phy_cfg {
 	/* phy-type - PCIE/UFS/USB */
@@ -1834,14 +1984,24 @@ struct qmp_phy_cfg {
 	/* Init sequence for PHY blocks - serdes, tx, rx, pcs */
 	const struct qmp_phy_init_tbl *serdes_tbl;
 	int serdes_tbl_num;
+	const struct qmp_phy_init_tbl *serdes_tbl_sec;
+	int serdes_tbl_num_sec;
 	const struct qmp_phy_init_tbl *tx_tbl;
 	int tx_tbl_num;
+	const struct qmp_phy_init_tbl *tx_tbl_sec;
+	int tx_tbl_num_sec;
 	const struct qmp_phy_init_tbl *rx_tbl;
 	int rx_tbl_num;
+	const struct qmp_phy_init_tbl *rx_tbl_sec;
+	int rx_tbl_num_sec;
 	const struct qmp_phy_init_tbl *pcs_tbl;
 	int pcs_tbl_num;
+	const struct qmp_phy_init_tbl *pcs_tbl_sec;
+	int pcs_tbl_num_sec;
 	const struct qmp_phy_init_tbl *pcs_misc_tbl;
 	int pcs_misc_tbl_num;
+	const struct qmp_phy_init_tbl *pcs_misc_tbl_sec;
+	int pcs_misc_tbl_num_sec;
 
 	/* Init sequence for DP PHY block link rates */
 	const struct qmp_phy_init_tbl *serdes_tbl_rbr;
@@ -2245,6 +2405,83 @@ static const struct qmp_phy_cfg sdm845_qhp_pciephy_cfg = {
 	.pwrdn_delay_max	= 1005,		/* us */
 };
 
+static const struct qmp_phy_cfg sm8250_qmp_gen3x1_pciephy_cfg = {
+	.type = PHY_TYPE_PCIE,
+	.nlanes = 1,
+
+	.serdes_tbl		= sm8250_qmp_pcie_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_serdes_tbl),
+	.serdes_tbl_sec		= sm8250_qmp_gen3x1_pcie_serdes_tbl,
+	.serdes_tbl_num_sec	= ARRAY_SIZE(sm8250_qmp_gen3x1_pcie_serdes_tbl),
+	.tx_tbl			= sm8250_qmp_pcie_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_tx_tbl),
+	.rx_tbl			= sm8250_qmp_pcie_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_rx_tbl),
+	.rx_tbl_sec		= sm8250_qmp_gen3x1_pcie_rx_tbl,
+	.rx_tbl_num_sec		= ARRAY_SIZE(sm8250_qmp_gen3x1_pcie_rx_tbl),
+	.pcs_tbl		= sm8250_qmp_pcie_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_pcs_tbl),
+	.pcs_tbl_sec		= sm8250_qmp_gen3x1_pcie_pcs_tbl,
+	.pcs_tbl_num_sec		= ARRAY_SIZE(sm8250_qmp_gen3x1_pcie_pcs_tbl),
+	.pcs_misc_tbl		= sm8250_qmp_pcie_pcs_misc_tbl,
+	.pcs_misc_tbl_num	= ARRAY_SIZE(sm8250_qmp_pcie_pcs_misc_tbl),
+	.pcs_misc_tbl_sec		= sm8250_qmp_gen3x1_pcie_pcs_misc_tbl,
+	.pcs_misc_tbl_num_sec	= ARRAY_SIZE(sm8250_qmp_gen3x1_pcie_pcs_misc_tbl),
+	.clk_list		= sdm845_pciephy_clk_l,
+	.num_clks		= ARRAY_SIZE(sdm845_pciephy_clk_l),
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= sm8250_pcie_regs_layout,
+
+	.start_ctrl		= PCS_START | SERDES_START,
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= 995,		/* us */
+	.pwrdn_delay_max	= 1005,		/* us */
+};
+
+static const struct qmp_phy_cfg sm8250_qmp_gen3x2_pciephy_cfg = {
+	.type = PHY_TYPE_PCIE,
+	.nlanes = 2,
+
+	.serdes_tbl		= sm8250_qmp_pcie_serdes_tbl,
+	.serdes_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_serdes_tbl),
+	.tx_tbl			= sm8250_qmp_pcie_tx_tbl,
+	.tx_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_tx_tbl),
+	.tx_tbl_sec		= sm8250_qmp_gen3x2_pcie_tx_tbl,
+	.tx_tbl_num_sec		= ARRAY_SIZE(sm8250_qmp_gen3x2_pcie_tx_tbl),
+	.rx_tbl			= sm8250_qmp_pcie_rx_tbl,
+	.rx_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_rx_tbl),
+	.rx_tbl_sec		= sm8250_qmp_gen3x2_pcie_rx_tbl,
+	.rx_tbl_num_sec		= ARRAY_SIZE(sm8250_qmp_gen3x2_pcie_rx_tbl),
+	.pcs_tbl		= sm8250_qmp_pcie_pcs_tbl,
+	.pcs_tbl_num		= ARRAY_SIZE(sm8250_qmp_pcie_pcs_tbl),
+	.pcs_tbl_sec		= sm8250_qmp_gen3x2_pcie_pcs_tbl,
+	.pcs_tbl_num_sec		= ARRAY_SIZE(sm8250_qmp_gen3x2_pcie_pcs_tbl),
+	.pcs_misc_tbl		= sm8250_qmp_pcie_pcs_misc_tbl,
+	.pcs_misc_tbl_num	= ARRAY_SIZE(sm8250_qmp_pcie_pcs_misc_tbl),
+	.pcs_misc_tbl_sec		= sm8250_qmp_gen3x2_pcie_pcs_misc_tbl,
+	.pcs_misc_tbl_num_sec	= ARRAY_SIZE(sm8250_qmp_gen3x2_pcie_pcs_misc_tbl),
+	.clk_list		= sdm845_pciephy_clk_l,
+	.num_clks		= ARRAY_SIZE(sdm845_pciephy_clk_l),
+	.reset_list		= sdm845_pciephy_reset_l,
+	.num_resets		= ARRAY_SIZE(sdm845_pciephy_reset_l),
+	.vreg_list		= qmp_phy_vreg_l,
+	.num_vregs		= ARRAY_SIZE(qmp_phy_vreg_l),
+	.regs			= sm8250_pcie_regs_layout,
+
+	.start_ctrl		= PCS_START | SERDES_START,
+	.pwrdn_ctrl		= SW_PWRDN | REFCLK_DRV_DSBL,
+
+	.is_dual_lane_phy	= true,
+	.has_pwrdn_delay	= true,
+	.pwrdn_delay_min	= 995,		/* us */
+	.pwrdn_delay_max	= 1005,		/* us */
+};
+
 static const struct qmp_phy_cfg qmp_v3_usb3phy_cfg = {
 	.type			= PHY_TYPE_USB3,
 	.nlanes			= 1,
@@ -2629,6 +2866,9 @@ static int qcom_qmp_phy_serdes_init(struct qmp_phy *qphy)
 	int ret;
 
 	qcom_qmp_phy_configure(serdes, cfg->regs, serdes_tbl, serdes_tbl_num);
+	if (cfg->serdes_tbl_sec)
+		qcom_qmp_phy_configure(serdes, cfg->regs, cfg->serdes_tbl_sec,
+				       cfg->serdes_tbl_num_sec);
 
 	if (cfg->type == PHY_TYPE_DP) {
 		switch (dp_opts->link_rate) {
@@ -3117,10 +3357,19 @@ static int qcom_qmp_phy_power_on(struct phy *phy)
 	/* Tx, Rx, and PCS configurations */
 	qcom_qmp_phy_configure_lane(tx, cfg->regs,
 				    cfg->tx_tbl, cfg->tx_tbl_num, 1);
+	if (cfg->tx_tbl_sec)
+		qcom_qmp_phy_configure_lane(tx, cfg->regs, cfg->tx_tbl_sec,
+					    cfg->tx_tbl_num_sec, 1);
+
 	/* Configuration for other LANE for USB-DP combo PHY */
-	if (cfg->is_dual_lane_phy)
+	if (cfg->is_dual_lane_phy) {
 		qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
 					    cfg->tx_tbl, cfg->tx_tbl_num, 2);
+		if (cfg->tx_tbl_sec)
+			qcom_qmp_phy_configure_lane(qphy->tx2, cfg->regs,
+						    cfg->tx_tbl_sec,
+						    cfg->tx_tbl_num_sec, 2);
+	}
 
 	/* Configure special DP tx tunings */
 	if (cfg->type == PHY_TYPE_DP)
@@ -3128,16 +3377,28 @@ static int qcom_qmp_phy_power_on(struct phy *phy)
 
 	qcom_qmp_phy_configure_lane(rx, cfg->regs,
 				    cfg->rx_tbl, cfg->rx_tbl_num, 1);
+	if (cfg->rx_tbl_sec)
+		qcom_qmp_phy_configure_lane(rx, cfg->regs,
+					    cfg->rx_tbl_sec, cfg->rx_tbl_num_sec, 1);
 
-	if (cfg->is_dual_lane_phy)
+	if (cfg->is_dual_lane_phy) {
 		qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
 					    cfg->rx_tbl, cfg->rx_tbl_num, 2);
+		if (cfg->rx_tbl_sec)
+			qcom_qmp_phy_configure_lane(qphy->rx2, cfg->regs,
+						    cfg->rx_tbl_sec,
+						    cfg->rx_tbl_num_sec, 2);
+	}
 
 	/* Configure link rate, swing, etc. */
-	if (cfg->type == PHY_TYPE_DP)
+	if (cfg->type == PHY_TYPE_DP) {
 		qcom_qmp_phy_configure_dp_phy(qphy);
-	else
+	} else {
 		qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl, cfg->pcs_tbl_num);
+		if (cfg->pcs_tbl_sec)
+			qcom_qmp_phy_configure(pcs, cfg->regs, cfg->pcs_tbl_sec,
+					       cfg->pcs_tbl_num_sec);
+	}
 
 	ret = reset_control_deassert(qmp->ufs_reset);
 	if (ret)
@@ -3145,6 +3406,9 @@ static int qcom_qmp_phy_power_on(struct phy *phy)
 
 	qcom_qmp_phy_configure(pcs_misc, cfg->regs, cfg->pcs_misc_tbl,
 			       cfg->pcs_misc_tbl_num);
+	if (cfg->pcs_misc_tbl_sec)
+		qcom_qmp_phy_configure(pcs_misc, cfg->regs, cfg->pcs_misc_tbl_sec,
+				       cfg->pcs_misc_tbl_num_sec);
 
 	/*
 	 * Pull out PHY from POWER DOWN state.
@@ -3900,6 +4164,15 @@ static const struct of_device_id qcom_qmp_phy_of_match_table[] = {
 	}, {
 		.compatible = "qcom,sm8250-qmp-usb3-uni-phy",
 		.data = &sm8250_usb3_uniphy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-gen3x1-pcie-phy",
+		.data = &sm8250_qmp_gen3x1_pciephy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-gen3x2-pcie-phy",
+		.data = &sm8250_qmp_gen3x2_pciephy_cfg,
+	}, {
+		.compatible = "qcom,sm8250-qmp-modem-pcie-phy",
+		.data = &sm8250_qmp_gen3x2_pciephy_cfg,
 	},
 	{ },
 };
diff --git a/drivers/phy/qualcomm/phy-qcom-qmp.h b/drivers/phy/qualcomm/phy-qcom-qmp.h
index b7c530088a6c..db92a461dd2e 100644
--- a/drivers/phy/qualcomm/phy-qcom-qmp.h
+++ b/drivers/phy/qualcomm/phy-qcom-qmp.h
@@ -403,6 +403,7 @@
 #define QSERDES_V4_COM_SSC_STEP_SIZE2_MODE0		0x028
 #define QSERDES_V4_COM_SSC_STEP_SIZE1_MODE1		0x030
 #define QSERDES_V4_COM_SSC_STEP_SIZE2_MODE1		0x034
+#define QSERDES_V4_COM_CLK_ENABLE1			0x048
 #define QSERDES_V4_COM_SYSCLK_BUF_ENABLE		0x050
 #define QSERDES_V4_COM_PLL_IVCO				0x058
 #define QSERDES_V4_COM_CMN_IPTRIM			0x060
@@ -432,6 +433,7 @@
 #define QSERDES_V4_COM_VCO_TUNE1_MODE1			0x118
 #define QSERDES_V4_COM_VCO_TUNE2_MODE1			0x11c
 #define QSERDES_V4_COM_VCO_TUNE_INITVAL2		0x124
+#define QSERDES_V4_COM_CLK_SELECT			0x154
 #define QSERDES_V4_COM_HSCLK_SEL			0x158
 #define QSERDES_V4_COM_HSCLK_HS_SWITCH_SEL		0x15c
 #define QSERDES_V4_COM_CORECLK_DIV_MODE1		0x16c
@@ -471,12 +473,14 @@
 #define QSERDES_V4_RX_UCDR_SB2_GAIN1			0x054
 #define QSERDES_V4_RX_UCDR_SB2_GAIN2			0x058
 #define QSERDES_V4_RX_AUX_DATA_TCOARSE_TFINE			0x060
+#define QSERDES_V4_RX_RCLK_AUXDATA_SEL			0x064
 #define QSERDES_V4_RX_AC_JTAG_ENABLE			0x068
 #define QSERDES_V4_RX_AC_JTAG_MODE			0x078
 #define QSERDES_V4_RX_RX_TERM_BW			0x080
 #define QSERDES_V4_RX_VGA_CAL_CNTRL1			0x0d4
 #define QSERDES_V4_RX_VGA_CAL_CNTRL2			0x0d8
 #define QSERDES_V4_RX_GM_CAL				0x0dc
+#define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL1		0x0e8
 #define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL2		0x0ec
 #define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL3		0x0f0
 #define QSERDES_V4_RX_RX_EQU_ADAPTOR_CNTRL4		0x0f4
@@ -485,6 +489,7 @@
 #define QSERDES_V4_RX_RX_IDAC_MEASURE_TIME		0x100
 #define QSERDES_V4_RX_RX_EQ_OFFSET_ADAPTOR_CNTRL1	0x110
 #define QSERDES_V4_RX_RX_OFFSET_ADAPTOR_CNTRL2		0x114
+#define QSERDES_V4_RX_SIGDET_ENABLES			0x118
 #define QSERDES_V4_RX_SIGDET_CNTRL			0x11c
 #define QSERDES_V4_RX_SIGDET_LVL			0x120
 #define QSERDES_V4_RX_SIGDET_DEGLITCH_CNTRL		0x124
@@ -806,4 +811,17 @@
 #define QPHY_V4_PCS_MISC_TYPEC_STATUS			0x10
 #define QPHY_V4_PCS_MISC_PLACEHOLDER_STATUS		0x14
 
+/* Only for QMP V4 PHY - PCS_PCIE registers (same as PCS_MISC?) */
+#define QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG2		0x0c
+#define QPHY_V4_PCS_PCIE_POWER_STATE_CONFIG4		0x14
+#define QPHY_V4_PCS_PCIE_ENDPOINT_REFCLK_DRIVE		0x1c
+#define QPHY_V4_PCS_PCIE_L1P1_WAKEUP_DLY_TIME_AUXCLK_L	0x40
+#define QPHY_V4_PCS_PCIE_L1P2_WAKEUP_DLY_TIME_AUXCLK_L	0x48
+#define QPHY_V4_PCS_PCIE_INT_AUX_CLK_CONFIG1		0x50
+#define QPHY_V4_PCS_PCIE_OSC_DTCT_ACTIONS		0x90
+#define QPHY_V4_PCS_PCIE_EQ_CONFIG2			0xa4
+#define QPHY_V4_PCS_PCIE_PRESET_P6_P7_PRE		0xb4
+#define QPHY_V4_PCS_PCIE_PRESET_P10_PRE			0xbc
+#define QPHY_V4_PCS_PCIE_PRESET_P10_POST		0xe0
+
 #endif
-- 
2.17.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v5 3/5] dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
  2020-10-27 17:00 [PATCH v5 0/5] Add PCIe support for SM8250 SoC Manivannan Sadhasivam
  2020-10-27 17:00 ` [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings Manivannan Sadhasivam
  2020-10-27 17:00 ` [PATCH v5 2/5] phy: qcom-qmp: Add SM8250 PCIe QMP PHYs Manivannan Sadhasivam
@ 2020-10-27 17:00 ` Manivannan Sadhasivam
  2020-11-22  4:10   ` Bjorn Andersson
  2020-10-27 17:00 ` [PATCH v5 4/5] PCI: qcom: Add SM8250 SoC support Manivannan Sadhasivam
  2020-10-27 17:00 ` [PATCH v5 5/5] PCI: qcom: Add support for configuring BDF to SID mapping for SM8250 Manivannan Sadhasivam
  4 siblings, 1 reply; 11+ messages in thread
From: Manivannan Sadhasivam @ 2020-10-27 17:00 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, vkoul, robh
  Cc: svarbanov, bhelgaas, lorenzo.pieralisi, linux-arm-msm, linux-pci,
	linux-kernel, mgautam, devicetree, truong, Manivannan Sadhasivam

Document the PCIe DT bindings for SM8250 SoC. The PCIe IP is similar to
the one used on SDM845, hence just add the compatible along with the
optional "atu" register region.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Rob Herring <robh@kernel.org>
---
 Documentation/devicetree/bindings/pci/qcom,pcie.txt | 6 ++++--
 1 file changed, 4 insertions(+), 2 deletions(-)

diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
index 02bc81bb8b2d..3b55310390a0 100644
--- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
+++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
@@ -13,6 +13,7 @@
 			- "qcom,pcie-ipq8074" for ipq8074
 			- "qcom,pcie-qcs404" for qcs404
 			- "qcom,pcie-sdm845" for sdm845
+			- "qcom,pcie-sm8250" for sm8250
 
 - reg:
 	Usage: required
@@ -27,6 +28,7 @@
 			- "dbi"	   DesignWare PCIe registers
 			- "elbi"   External local bus interface registers
 			- "config" PCIe configuration space
+			- "atu"    ATU address space (optional)
 
 - device_type:
 	Usage: required
@@ -131,7 +133,7 @@
 			- "slave_bus"	AXI Slave clock
 
 -clock-names:
-	Usage: required for sdm845
+	Usage: required for sdm845 and sm8250
 	Value type: <stringlist>
 	Definition: Should contain the following entries
 			- "aux"		Auxiliary clock
@@ -206,7 +208,7 @@
 			- "ahb"			AHB reset
 
 - reset-names:
-	Usage: required for sdm845
+	Usage: required for sdm845 and sm8250
 	Value type: <stringlist>
 	Definition: Should contain the following entries
 			- "pci"			PCIe core reset
-- 
2.17.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v5 4/5] PCI: qcom: Add SM8250 SoC support
  2020-10-27 17:00 [PATCH v5 0/5] Add PCIe support for SM8250 SoC Manivannan Sadhasivam
                   ` (2 preceding siblings ...)
  2020-10-27 17:00 ` [PATCH v5 3/5] dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC Manivannan Sadhasivam
@ 2020-10-27 17:00 ` Manivannan Sadhasivam
  2020-11-22  4:12   ` Bjorn Andersson
  2020-10-27 17:00 ` [PATCH v5 5/5] PCI: qcom: Add support for configuring BDF to SID mapping for SM8250 Manivannan Sadhasivam
  4 siblings, 1 reply; 11+ messages in thread
From: Manivannan Sadhasivam @ 2020-10-27 17:00 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, vkoul, robh
  Cc: svarbanov, bhelgaas, lorenzo.pieralisi, linux-arm-msm, linux-pci,
	linux-kernel, mgautam, devicetree, truong, Manivannan Sadhasivam

The PCIe IP (rev 1.9.0) on SM8250 SoC is similar to the one used on
SDM845. Hence the support is added reusing the members of ops_2_7_0.
The key difference between ops_2_7_0 and ops_1_9_0 is the config_sid
callback, which will be added in successive commit.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
---
 drivers/pci/controller/dwc/pcie-qcom.c | 11 +++++++++++
 1 file changed, 11 insertions(+)

diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index b4761640ffd9..0b180a19b0ea 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -1361,6 +1361,16 @@ static const struct qcom_pcie_ops ops_2_7_0 = {
 	.post_deinit = qcom_pcie_post_deinit_2_7_0,
 };
 
+/* Qcom IP rev.: 1.9.0 */
+static const struct qcom_pcie_ops ops_1_9_0 = {
+	.get_resources = qcom_pcie_get_resources_2_7_0,
+	.init = qcom_pcie_init_2_7_0,
+	.deinit = qcom_pcie_deinit_2_7_0,
+	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
+	.post_init = qcom_pcie_post_init_2_7_0,
+	.post_deinit = qcom_pcie_post_deinit_2_7_0,
+};
+
 static const struct dw_pcie_ops dw_pcie_ops = {
 	.link_up = qcom_pcie_link_up,
 };
@@ -1474,6 +1484,7 @@ static const struct of_device_id qcom_pcie_match[] = {
 	{ .compatible = "qcom,pcie-ipq4019", .data = &ops_2_4_0 },
 	{ .compatible = "qcom,pcie-qcs404", .data = &ops_2_4_0 },
 	{ .compatible = "qcom,pcie-sdm845", .data = &ops_2_7_0 },
+	{ .compatible = "qcom,pcie-sm8250", .data = &ops_1_9_0 },
 	{ }
 };
 
-- 
2.17.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* [PATCH v5 5/5] PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
  2020-10-27 17:00 [PATCH v5 0/5] Add PCIe support for SM8250 SoC Manivannan Sadhasivam
                   ` (3 preceding siblings ...)
  2020-10-27 17:00 ` [PATCH v5 4/5] PCI: qcom: Add SM8250 SoC support Manivannan Sadhasivam
@ 2020-10-27 17:00 ` Manivannan Sadhasivam
  2020-11-22  4:18   ` Bjorn Andersson
  4 siblings, 1 reply; 11+ messages in thread
From: Manivannan Sadhasivam @ 2020-10-27 17:00 UTC (permalink / raw)
  To: agross, bjorn.andersson, kishon, vkoul, robh
  Cc: svarbanov, bhelgaas, lorenzo.pieralisi, linux-arm-msm, linux-pci,
	linux-kernel, mgautam, devicetree, truong, Manivannan Sadhasivam

For SM8250, we need to write the BDF to SID mapping in PCIe controller
register space for proper working. This is accomplished by extracting
the BDF and SID values from "iommu-map" property in DT and writing those
in the register address calculated from the hash value of BDF. In case
of collisions, the index of the next entry will also be written.

For the sake of it, let's introduce a "config_sid" callback and do it
conditionally for SM8250.

Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
---

Rob: I've dropped your review tag as this patch has gone through some
change (mostly cleanups though)

 drivers/pci/controller/dwc/Kconfig     |  1 +
 drivers/pci/controller/dwc/pcie-qcom.c | 81 ++++++++++++++++++++++++++
 2 files changed, 82 insertions(+)

diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index bc049865f8e0..875ebc6e8884 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -169,6 +169,7 @@ config PCIE_QCOM
 	depends on OF && (ARCH_QCOM || COMPILE_TEST)
 	depends on PCI_MSI_IRQ_DOMAIN
 	select PCIE_DW_HOST
+	select CRC8
 	help
 	  Say Y here to enable PCIe controller support on Qualcomm SoCs. The
 	  PCIe controller uses the DesignWare core plus Qualcomm-specific
diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
index 0b180a19b0ea..2148fcf74294 100644
--- a/drivers/pci/controller/dwc/pcie-qcom.c
+++ b/drivers/pci/controller/dwc/pcie-qcom.c
@@ -9,6 +9,7 @@
  */
 
 #include <linux/clk.h>
+#include <linux/crc8.h>
 #include <linux/delay.h>
 #include <linux/gpio/consumer.h>
 #include <linux/interrupt.h>
@@ -57,6 +58,7 @@
 #define PCIE20_PARF_SID_OFFSET			0x234
 #define PCIE20_PARF_BDF_TRANSLATE_CFG		0x24C
 #define PCIE20_PARF_DEVICE_TYPE			0x1000
+#define PCIE20_PARF_BDF_TO_SID_TABLE_N		0x2000
 
 #define PCIE20_ELBI_SYS_CTRL			0x04
 #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE		BIT(0)
@@ -97,6 +99,9 @@
 
 #define QCOM_PCIE_2_1_0_MAX_SUPPLY	3
 #define QCOM_PCIE_2_1_0_MAX_CLOCKS	5
+
+#define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
+
 struct qcom_pcie_resources_2_1_0 {
 	struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
 	struct reset_control *pci_reset;
@@ -179,6 +184,7 @@ struct qcom_pcie_ops {
 	void (*deinit)(struct qcom_pcie *pcie);
 	void (*post_deinit)(struct qcom_pcie *pcie);
 	void (*ltssm_enable)(struct qcom_pcie *pcie);
+	int (*config_sid)(struct qcom_pcie *pcie);
 };
 
 struct qcom_pcie {
@@ -1261,6 +1267,74 @@ static int qcom_pcie_link_up(struct dw_pcie *pci)
 	return !!(val & PCI_EXP_LNKSTA_DLLLA);
 }
 
+static int qcom_pcie_config_sid_sm8250(struct qcom_pcie *pcie)
+{
+	/* iommu map structure */
+	struct {
+		u32 bdf;
+		u32 phandle;
+		u32 smmu_sid;
+		u32 smmu_sid_len;
+	} *map;
+	void __iomem *bdf_to_sid_base = pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N;
+	struct device *dev = pcie->pci->dev;
+	u8 qcom_pcie_crc8_table[CRC8_TABLE_SIZE];
+	int i, nr_map, size = 0;
+	u32 smmu_sid_base;
+
+	of_get_property(dev->of_node, "iommu-map", &size);
+	if (!size)
+		return 0;
+
+	map = kzalloc(size, GFP_KERNEL);
+	if (!map)
+		return -ENOMEM;
+
+	of_property_read_u32_array(dev->of_node,
+		"iommu-map", (u32 *)map, size / sizeof(u32));
+
+	nr_map = size / (sizeof(*map));
+
+	crc8_populate_msb(qcom_pcie_crc8_table, QCOM_PCIE_CRC8_POLYNOMIAL);
+
+	/* Registers need to be zero out first */
+	memset_io(bdf_to_sid_base, 0, CRC8_TABLE_SIZE * sizeof(u32));
+
+	/* Look for an available entry to hold the mapping */
+	for (i = 0; i < nr_map; i++) {
+		u16 bdf_be = cpu_to_be16(map[i].bdf);
+		u32 val;
+		u8 hash;
+
+		hash = crc8(qcom_pcie_crc8_table, (u8 *)&bdf_be, sizeof(bdf_be),
+			0);
+
+		val = readl(bdf_to_sid_base + hash * sizeof(u32));
+
+		/* If the register is already populated, look for next available entry */
+		while (val) {
+			u8 current_hash = hash++;
+			u8 next_mask = 0xff;
+
+			/* If NEXT field is NULL then update it with next hash */
+			if (!(val & next_mask)) {
+				val |= (u32)hash;
+				writel(val, bdf_to_sid_base + current_hash * sizeof(u32));
+			}
+
+			val = readl(bdf_to_sid_base + hash * sizeof(u32));
+		}
+
+		/* BDF [31:16] | SID [15:8] | NEXT [7:0] */
+		val = map[i].bdf << 16 | (map[i].smmu_sid - smmu_sid_base) << 8 | 0;
+		writel(val, bdf_to_sid_base + hash * sizeof(u32));
+	}
+
+	kfree(map);
+
+	return 0;
+}
+
 static int qcom_pcie_host_init(struct pcie_port *pp)
 {
 	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
@@ -1292,6 +1366,12 @@ static int qcom_pcie_host_init(struct pcie_port *pp)
 	if (ret)
 		goto err;
 
+	if (pcie->ops->config_sid) {
+		ret = pcie->ops->config_sid(pcie);
+		if (ret)
+			goto err;
+	}
+
 	return 0;
 err:
 	qcom_ep_reset_assert(pcie);
@@ -1369,6 +1449,7 @@ static const struct qcom_pcie_ops ops_1_9_0 = {
 	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
 	.post_init = qcom_pcie_post_init_2_7_0,
 	.post_deinit = qcom_pcie_post_deinit_2_7_0,
+	.config_sid = qcom_pcie_config_sid_sm8250,
 };
 
 static const struct dw_pcie_ops dw_pcie_ops = {
-- 
2.17.1


^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings
  2020-10-27 17:00 ` [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings Manivannan Sadhasivam
@ 2020-11-16  5:58   ` Vinod Koul
  0 siblings, 0 replies; 11+ messages in thread
From: Vinod Koul @ 2020-11-16  5:58 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: agross, bjorn.andersson, kishon, robh, svarbanov, bhelgaas,
	lorenzo.pieralisi, linux-arm-msm, linux-pci, linux-kernel,
	mgautam, devicetree, truong

On 27-10-20, 22:30, Manivannan Sadhasivam wrote:
> Add the below three PCIe PHYs found in SM8250 to the QMP binding:
> 
> QMP GEN3x1 PHY - 1 lane
> QMP GEN3x2 PHY - 2 lanes
> QMP Modem PHY - 2 lanes
> 

Applied, thanks

-- 
~Vinod

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v5 2/5] phy: qcom-qmp: Add SM8250 PCIe QMP PHYs
  2020-10-27 17:00 ` [PATCH v5 2/5] phy: qcom-qmp: Add SM8250 PCIe QMP PHYs Manivannan Sadhasivam
@ 2020-11-16  5:58   ` Vinod Koul
  0 siblings, 0 replies; 11+ messages in thread
From: Vinod Koul @ 2020-11-16  5:58 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: agross, bjorn.andersson, kishon, robh, svarbanov, bhelgaas,
	lorenzo.pieralisi, linux-arm-msm, linux-pci, linux-kernel,
	mgautam, devicetree, truong

On 27-10-20, 22:30, Manivannan Sadhasivam wrote:
> SM8250 has multiple different PHY versions:
> QMP GEN3x1 PHY - 1 lane
> QMP GEN3x2 PHY - 2 lanes
> QMP Modem PHY - 2 lanes
> 
> Add support for these with relevant init sequence. In order to abstract
> the init sequence, this commit introduces secondary tables which can
> be used to factor out the unique sequence for each PHY while the former
> tables can have the common sequence.

Applied, thanks

-- 
~Vinod

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v5 3/5] dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC
  2020-10-27 17:00 ` [PATCH v5 3/5] dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC Manivannan Sadhasivam
@ 2020-11-22  4:10   ` Bjorn Andersson
  0 siblings, 0 replies; 11+ messages in thread
From: Bjorn Andersson @ 2020-11-22  4:10 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: agross, kishon, vkoul, robh, svarbanov, bhelgaas,
	lorenzo.pieralisi, linux-arm-msm, linux-pci, linux-kernel,
	mgautam, devicetree, truong

On Tue 27 Oct 12:00 CDT 2020, Manivannan Sadhasivam wrote:

> Document the PCIe DT bindings for SM8250 SoC. The PCIe IP is similar to
> the one used on SDM845, hence just add the compatible along with the
> optional "atu" register region.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Acked-by: Rob Herring <robh@kernel.org>

Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

> ---
>  Documentation/devicetree/bindings/pci/qcom,pcie.txt | 6 ++++--
>  1 file changed, 4 insertions(+), 2 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/qcom,pcie.txt b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> index 02bc81bb8b2d..3b55310390a0 100644
> --- a/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/qcom,pcie.txt
> @@ -13,6 +13,7 @@
>  			- "qcom,pcie-ipq8074" for ipq8074
>  			- "qcom,pcie-qcs404" for qcs404
>  			- "qcom,pcie-sdm845" for sdm845
> +			- "qcom,pcie-sm8250" for sm8250
>  
>  - reg:
>  	Usage: required
> @@ -27,6 +28,7 @@
>  			- "dbi"	   DesignWare PCIe registers
>  			- "elbi"   External local bus interface registers
>  			- "config" PCIe configuration space
> +			- "atu"    ATU address space (optional)
>  
>  - device_type:
>  	Usage: required
> @@ -131,7 +133,7 @@
>  			- "slave_bus"	AXI Slave clock
>  
>  -clock-names:
> -	Usage: required for sdm845
> +	Usage: required for sdm845 and sm8250
>  	Value type: <stringlist>
>  	Definition: Should contain the following entries
>  			- "aux"		Auxiliary clock
> @@ -206,7 +208,7 @@
>  			- "ahb"			AHB reset
>  
>  - reset-names:
> -	Usage: required for sdm845
> +	Usage: required for sdm845 and sm8250
>  	Value type: <stringlist>
>  	Definition: Should contain the following entries
>  			- "pci"			PCIe core reset
> -- 
> 2.17.1
> 

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v5 4/5] PCI: qcom: Add SM8250 SoC support
  2020-10-27 17:00 ` [PATCH v5 4/5] PCI: qcom: Add SM8250 SoC support Manivannan Sadhasivam
@ 2020-11-22  4:12   ` Bjorn Andersson
  0 siblings, 0 replies; 11+ messages in thread
From: Bjorn Andersson @ 2020-11-22  4:12 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: agross, kishon, vkoul, robh, svarbanov, bhelgaas,
	lorenzo.pieralisi, linux-arm-msm, linux-pci, linux-kernel,
	mgautam, devicetree, truong

On Tue 27 Oct 12:00 CDT 2020, Manivannan Sadhasivam wrote:

> The PCIe IP (rev 1.9.0) on SM8250 SoC is similar to the one used on
> SDM845. Hence the support is added reusing the members of ops_2_7_0.
> The key difference between ops_2_7_0 and ops_1_9_0 is the config_sid
> callback, which will be added in successive commit.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
> Reviewed-by: Rob Herring <robh@kernel.org>

Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Regards,
Bjorn

> ---
>  drivers/pci/controller/dwc/pcie-qcom.c | 11 +++++++++++
>  1 file changed, 11 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index b4761640ffd9..0b180a19b0ea 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -1361,6 +1361,16 @@ static const struct qcom_pcie_ops ops_2_7_0 = {
>  	.post_deinit = qcom_pcie_post_deinit_2_7_0,
>  };
>  
> +/* Qcom IP rev.: 1.9.0 */
> +static const struct qcom_pcie_ops ops_1_9_0 = {
> +	.get_resources = qcom_pcie_get_resources_2_7_0,
> +	.init = qcom_pcie_init_2_7_0,
> +	.deinit = qcom_pcie_deinit_2_7_0,
> +	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
> +	.post_init = qcom_pcie_post_init_2_7_0,
> +	.post_deinit = qcom_pcie_post_deinit_2_7_0,
> +};
> +
>  static const struct dw_pcie_ops dw_pcie_ops = {
>  	.link_up = qcom_pcie_link_up,
>  };
> @@ -1474,6 +1484,7 @@ static const struct of_device_id qcom_pcie_match[] = {
>  	{ .compatible = "qcom,pcie-ipq4019", .data = &ops_2_4_0 },
>  	{ .compatible = "qcom,pcie-qcs404", .data = &ops_2_4_0 },
>  	{ .compatible = "qcom,pcie-sdm845", .data = &ops_2_7_0 },
> +	{ .compatible = "qcom,pcie-sm8250", .data = &ops_1_9_0 },
>  	{ }
>  };
>  
> -- 
> 2.17.1
> 

^ permalink raw reply	[flat|nested] 11+ messages in thread

* Re: [PATCH v5 5/5] PCI: qcom: Add support for configuring BDF to SID mapping for SM8250
  2020-10-27 17:00 ` [PATCH v5 5/5] PCI: qcom: Add support for configuring BDF to SID mapping for SM8250 Manivannan Sadhasivam
@ 2020-11-22  4:18   ` Bjorn Andersson
  0 siblings, 0 replies; 11+ messages in thread
From: Bjorn Andersson @ 2020-11-22  4:18 UTC (permalink / raw)
  To: Manivannan Sadhasivam
  Cc: agross, kishon, vkoul, robh, svarbanov, bhelgaas,
	lorenzo.pieralisi, linux-arm-msm, linux-pci, linux-kernel,
	mgautam, devicetree, truong

On Tue 27 Oct 12:00 CDT 2020, Manivannan Sadhasivam wrote:

> For SM8250, we need to write the BDF to SID mapping in PCIe controller
> register space for proper working. This is accomplished by extracting
> the BDF and SID values from "iommu-map" property in DT and writing those
> in the register address calculated from the hash value of BDF. In case
> of collisions, the index of the next entry will also be written.
> 
> For the sake of it, let's introduce a "config_sid" callback and do it
> conditionally for SM8250.
> 
> Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>

Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Regards,
Bjorn

> ---
> 
> Rob: I've dropped your review tag as this patch has gone through some
> change (mostly cleanups though)
> 
>  drivers/pci/controller/dwc/Kconfig     |  1 +
>  drivers/pci/controller/dwc/pcie-qcom.c | 81 ++++++++++++++++++++++++++
>  2 files changed, 82 insertions(+)
> 
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index bc049865f8e0..875ebc6e8884 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -169,6 +169,7 @@ config PCIE_QCOM
>  	depends on OF && (ARCH_QCOM || COMPILE_TEST)
>  	depends on PCI_MSI_IRQ_DOMAIN
>  	select PCIE_DW_HOST
> +	select CRC8
>  	help
>  	  Say Y here to enable PCIe controller support on Qualcomm SoCs. The
>  	  PCIe controller uses the DesignWare core plus Qualcomm-specific
> diff --git a/drivers/pci/controller/dwc/pcie-qcom.c b/drivers/pci/controller/dwc/pcie-qcom.c
> index 0b180a19b0ea..2148fcf74294 100644
> --- a/drivers/pci/controller/dwc/pcie-qcom.c
> +++ b/drivers/pci/controller/dwc/pcie-qcom.c
> @@ -9,6 +9,7 @@
>   */
>  
>  #include <linux/clk.h>
> +#include <linux/crc8.h>
>  #include <linux/delay.h>
>  #include <linux/gpio/consumer.h>
>  #include <linux/interrupt.h>
> @@ -57,6 +58,7 @@
>  #define PCIE20_PARF_SID_OFFSET			0x234
>  #define PCIE20_PARF_BDF_TRANSLATE_CFG		0x24C
>  #define PCIE20_PARF_DEVICE_TYPE			0x1000
> +#define PCIE20_PARF_BDF_TO_SID_TABLE_N		0x2000
>  
>  #define PCIE20_ELBI_SYS_CTRL			0x04
>  #define PCIE20_ELBI_SYS_CTRL_LT_ENABLE		BIT(0)
> @@ -97,6 +99,9 @@
>  
>  #define QCOM_PCIE_2_1_0_MAX_SUPPLY	3
>  #define QCOM_PCIE_2_1_0_MAX_CLOCKS	5
> +
> +#define QCOM_PCIE_CRC8_POLYNOMIAL (BIT(2) | BIT(1) | BIT(0))
> +
>  struct qcom_pcie_resources_2_1_0 {
>  	struct clk_bulk_data clks[QCOM_PCIE_2_1_0_MAX_CLOCKS];
>  	struct reset_control *pci_reset;
> @@ -179,6 +184,7 @@ struct qcom_pcie_ops {
>  	void (*deinit)(struct qcom_pcie *pcie);
>  	void (*post_deinit)(struct qcom_pcie *pcie);
>  	void (*ltssm_enable)(struct qcom_pcie *pcie);
> +	int (*config_sid)(struct qcom_pcie *pcie);
>  };
>  
>  struct qcom_pcie {
> @@ -1261,6 +1267,74 @@ static int qcom_pcie_link_up(struct dw_pcie *pci)
>  	return !!(val & PCI_EXP_LNKSTA_DLLLA);
>  }
>  
> +static int qcom_pcie_config_sid_sm8250(struct qcom_pcie *pcie)
> +{
> +	/* iommu map structure */
> +	struct {
> +		u32 bdf;
> +		u32 phandle;
> +		u32 smmu_sid;
> +		u32 smmu_sid_len;
> +	} *map;
> +	void __iomem *bdf_to_sid_base = pcie->parf + PCIE20_PARF_BDF_TO_SID_TABLE_N;
> +	struct device *dev = pcie->pci->dev;
> +	u8 qcom_pcie_crc8_table[CRC8_TABLE_SIZE];
> +	int i, nr_map, size = 0;
> +	u32 smmu_sid_base;
> +
> +	of_get_property(dev->of_node, "iommu-map", &size);
> +	if (!size)
> +		return 0;
> +
> +	map = kzalloc(size, GFP_KERNEL);
> +	if (!map)
> +		return -ENOMEM;
> +
> +	of_property_read_u32_array(dev->of_node,
> +		"iommu-map", (u32 *)map, size / sizeof(u32));
> +
> +	nr_map = size / (sizeof(*map));
> +
> +	crc8_populate_msb(qcom_pcie_crc8_table, QCOM_PCIE_CRC8_POLYNOMIAL);
> +
> +	/* Registers need to be zero out first */
> +	memset_io(bdf_to_sid_base, 0, CRC8_TABLE_SIZE * sizeof(u32));
> +
> +	/* Look for an available entry to hold the mapping */
> +	for (i = 0; i < nr_map; i++) {
> +		u16 bdf_be = cpu_to_be16(map[i].bdf);
> +		u32 val;
> +		u8 hash;
> +
> +		hash = crc8(qcom_pcie_crc8_table, (u8 *)&bdf_be, sizeof(bdf_be),
> +			0);
> +
> +		val = readl(bdf_to_sid_base + hash * sizeof(u32));
> +
> +		/* If the register is already populated, look for next available entry */
> +		while (val) {
> +			u8 current_hash = hash++;
> +			u8 next_mask = 0xff;
> +
> +			/* If NEXT field is NULL then update it with next hash */
> +			if (!(val & next_mask)) {
> +				val |= (u32)hash;
> +				writel(val, bdf_to_sid_base + current_hash * sizeof(u32));
> +			}
> +
> +			val = readl(bdf_to_sid_base + hash * sizeof(u32));
> +		}
> +
> +		/* BDF [31:16] | SID [15:8] | NEXT [7:0] */
> +		val = map[i].bdf << 16 | (map[i].smmu_sid - smmu_sid_base) << 8 | 0;
> +		writel(val, bdf_to_sid_base + hash * sizeof(u32));
> +	}
> +
> +	kfree(map);
> +
> +	return 0;
> +}
> +
>  static int qcom_pcie_host_init(struct pcie_port *pp)
>  {
>  	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> @@ -1292,6 +1366,12 @@ static int qcom_pcie_host_init(struct pcie_port *pp)
>  	if (ret)
>  		goto err;
>  
> +	if (pcie->ops->config_sid) {
> +		ret = pcie->ops->config_sid(pcie);
> +		if (ret)
> +			goto err;
> +	}
> +
>  	return 0;
>  err:
>  	qcom_ep_reset_assert(pcie);
> @@ -1369,6 +1449,7 @@ static const struct qcom_pcie_ops ops_1_9_0 = {
>  	.ltssm_enable = qcom_pcie_2_3_2_ltssm_enable,
>  	.post_init = qcom_pcie_post_init_2_7_0,
>  	.post_deinit = qcom_pcie_post_deinit_2_7_0,
> +	.config_sid = qcom_pcie_config_sid_sm8250,
>  };
>  
>  static const struct dw_pcie_ops dw_pcie_ops = {
> -- 
> 2.17.1
> 

^ permalink raw reply	[flat|nested] 11+ messages in thread

end of thread, back to index

Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-10-27 17:00 [PATCH v5 0/5] Add PCIe support for SM8250 SoC Manivannan Sadhasivam
2020-10-27 17:00 ` [PATCH v5 1/5] dt-bindings: phy: qcom,qmp: Add SM8250 PCIe PHY bindings Manivannan Sadhasivam
2020-11-16  5:58   ` Vinod Koul
2020-10-27 17:00 ` [PATCH v5 2/5] phy: qcom-qmp: Add SM8250 PCIe QMP PHYs Manivannan Sadhasivam
2020-11-16  5:58   ` Vinod Koul
2020-10-27 17:00 ` [PATCH v5 3/5] dt-bindings: pci: qcom: Document PCIe bindings for SM8250 SoC Manivannan Sadhasivam
2020-11-22  4:10   ` Bjorn Andersson
2020-10-27 17:00 ` [PATCH v5 4/5] PCI: qcom: Add SM8250 SoC support Manivannan Sadhasivam
2020-11-22  4:12   ` Bjorn Andersson
2020-10-27 17:00 ` [PATCH v5 5/5] PCI: qcom: Add support for configuring BDF to SID mapping for SM8250 Manivannan Sadhasivam
2020-11-22  4:18   ` Bjorn Andersson

Linux-PCI Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-pci/0 linux-pci/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-pci linux-pci/ https://lore.kernel.org/linux-pci \
		linux-pci@vger.kernel.org
	public-inbox-index linux-pci

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-pci


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git