[PATCH v3 0/3] Visconti: Add Toshiba Visconti PCIe host controller driver

[PATCH v3 0/3] Visconti: Add Toshiba Visconti PCIe host controller driver

[Nobuhiro Iwamatsu]

Hi,

This series is the PCIe driver for Toshiba's ARM SoC, Visconti[0].
This provides DT binding documentation, device driver, MAINTAINER files.

Best regards,
  Nobuhiro

[0]: https://toshiba.semicon-storage.com/ap-en/semiconductor/product/image-recognition-processors-visconti.html

  dt-bindings: pci: Add DT binding for Toshiba Visconti PCIe controller
    v2 -> v3:
      - No update.
    v1 -> v2:
      - Remove white space.
      - Drop num-viewport and bus-range from required.
      - Drop status line from example.
      - Drop bus-range from required.
      - Removed lines defined in pci-bus.yaml from required.

  PCI: Visconti: Add Toshiba Visconti PCIe host controller driver
    v2 -> v3:
      - Update subject.
      - Wrap description in 75 columns.
      - Change config name to PCIE_VISCONTI_HOST.
      - Update Kconfig text.
      - Drop empty lines.
      - Adjusted to 80 columns.
      - Drop inline from functions for register access.
      - Changed function name from visconti_pcie_check_link_status to
        visconti_pcie_link_up.
      - Update to using dw_pcie_host_init().
      - Reorder these in the order of use in visconti_pcie_establish_link().
      - Rewrite visconti_pcie_host_init() without dw_pcie_setup_rc().
      - Change function name from  visconti_device_turnon() to
        visconti_pcie_power_on().
      - Unify formats such as dev_err().
      - Drop error label in visconti_add_pcie_port(). 
    v1 -> v2:
      - Fix typo in commit message.
      - Drop "depends on OF && HAS_IOMEM" from Kconfig.
      - Stop using the pointer of struct dw_pcie.
      - Use _relaxed variant.
      - Drop dw_pcie_wait_for_link.
      - Drop dbi resource processing.
      - Drop MSI IRQ initialization processing.
  
  MAINTAINERS: Add entries for Toshiba Visconti PCIe controller
    v2 -> v3:
      - No update.
    v1 -> v2:
      - No update.

Nobuhiro Iwamatsu (3):
  dt-bindings: pci: Add DT binding for Toshiba Visconti PCIe controller
  PCI: Visconti: Add Toshiba Visconti PCIe host controller driver
  MAINTAINERS: Add entries for Toshiba Visconti PCIe controller

 .../bindings/pci/toshiba,visconti-pcie.yaml   | 110 ++++++
 MAINTAINERS                                   |   2 +
 drivers/pci/controller/dwc/Kconfig            |   9 +
 drivers/pci/controller/dwc/Makefile           |   1 +
 drivers/pci/controller/dwc/pcie-visconti.c    | 369 ++++++++++++++++++
 5 files changed, 491 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
 create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c

-- 
2.31.1

[PATCH v3 1/3] dt-bindings: pci: Add DT binding for Toshiba Visconti PCIe controller

[Nobuhiro Iwamatsu]

This commit adds the Device Tree binding documentation that allows
to describe the PCIe controller found in Toshiba Visconti SoCs.

v1 -> v2:
 - Remove white space.
 - Drop num-viewport and bus-range from required.
 - Drop status line from example.
 - Drop bus-range from required.
 - Removed lines defined in pci-bus.yaml from required.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
---
 .../bindings/pci/toshiba,visconti-pcie.yaml   | 110 ++++++++++++++++++
 1 file changed, 110 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml

diff --git a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
new file mode 100644
index 000000000000..d47a4a3c49e3
--- /dev/null
+++ b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
@@ -0,0 +1,110 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/pci/toshiba,visconti-pcie.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Toshiba Visconti5 SoC PCIe Host Controller Device Tree Bindings
+
+maintainers:
+  - Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+
+description: |+
+  Toshiba Visconti5 SoC PCIe host controller is based on the Synopsys DesignWare PCIe IP.
+
+allOf:
+  - $ref: /schemas/pci/pci-bus.yaml#
+
+properties:
+  compatible:
+    const: toshiba,visconti-pcie
+
+  reg:
+    items:
+      - description: Data Bus Interface (DBI) registers.
+      - description: PCIe configuration space region.
+      - description: Visconti specific additional registers.
+      - description: Visconti specific SMU registers
+      - description: Visconti specific memory protection unit registers (MPU)
+
+  reg-names:
+    items:
+      - const: dbi
+      - const: config
+      - const: ulreg
+      - const: smu
+      - const: mpu
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    items:
+      - description: PCIe reference clock
+      - description: PCIe system clock
+      - description: Auxiliary clock
+
+  clock-names:
+    items:
+      - const: pcie_refclk
+      - const: sysclk
+      - const: auxclk
+
+  num-lanes:
+    const: 2
+
+required:
+  - reg
+  - reg-names
+  - interrupts
+  - "#interrupt-cells"
+  - interrupt-map
+  - interrupt-map-mask
+  - num-lanes
+  - clocks
+  - clock-names
+  - max-link-speed
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    #include <dt-bindings/interrupt-controller/arm-gic.h>
+
+    soc {
+        #address-cells = <2>;
+        #size-cells = <2>;
+
+        pcie: pcie@28400000 {
+            compatible = "toshiba,visconti-pcie";
+            reg = <0x0 0x28400000 0x0 0x00400000>,
+                  <0x0 0x70000000 0x0 0x10000000>,
+                  <0x0 0x28050000 0x0 0x00010000>,
+                  <0x0 0x24200000 0x0 0x00002000>,
+                  <0x0 0x24162000 0x0 0x00001000>;
+            reg-names  = "dbi", "config", "ulreg", "smu", "mpu";
+            device_type = "pci";
+            bus-range = <0x00 0xff>;
+            num-lanes = <2>;
+            num-viewport = <8>;
+
+            #address-cells = <3>;
+            #size-cells = <2>;
+            #interrupt-cells = <1>;
+            ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000>,
+                     <0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>;
+            interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+            interrupt-names = "intr";
+            interrupt-map-mask = <0 0 0 7>;
+            interrupt-map =
+                <0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+                 0 0 0 2 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+                 0 0 0 3 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
+                 0 0 0 4 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
+            clocks = <&extclk100mhz>, <&clk600mhz>, <&clk25mhz>;
+            clock-names = "pcie_refclk", "sysclk", "auxclk";
+            max-link-speed = <2>;
+        };
+    };
+...
-- 
2.31.1

[PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Nobuhiro Iwamatsu]

Add support to PCIe RC controller on Toshiba Visconti ARM SoCs. PCIe
controller is based of Synopsys DesignWare PCIe core.

This patch does not yet use the clock framework to control the clock.
This will be replaced in the future.

v2 -> v3:
  - Update subject.
  - Wrap description in 75 columns.
  - Change config name to PCIE_VISCONTI_HOST.
  - Update Kconfig text.
  - Drop blank lines.
  - Adjusted to 80 columns.
  - Drop inline from functions for register access.
  - Changed function name from visconti_pcie_check_link_status to
    visconti_pcie_link_up.
  - Update to using dw_pcie_host_init().
  - Reorder these in the order of use in visconti_pcie_establish_link.
  - Rewrite visconti_pcie_host_init() without dw_pcie_setup_rc().
  - Change function name from  visconti_device_turnon() to
    visconti_pcie_power_on().
  - Unify formats such as dev_err().
  - Drop error label in visconti_add_pcie_port().

v1 -> v2:
  - Fix typo in commit message.
  - Drop "depends on OF && HAS_IOMEM" from Kconfig.
  - Stop using the pointer of struct dw_pcie.
  - Use _relaxed variant.
  - Drop dw_pcie_wait_for_link.
  - Drop dbi resource processing.
  - Drop MSI IRQ initialization processing.

Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
---
 drivers/pci/controller/dwc/Kconfig         |   9 +
 drivers/pci/controller/dwc/Makefile        |   1 +
 drivers/pci/controller/dwc/pcie-visconti.c | 369 +++++++++++++++++++++
 3 files changed, 379 insertions(+)
 create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c

diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
index 423d35872ce4..7c3dcb86fcad 100644
--- a/drivers/pci/controller/dwc/Kconfig
+++ b/drivers/pci/controller/dwc/Kconfig
@@ -286,6 +286,15 @@ config PCIE_TEGRA194_EP
 	  in order to enable device-specific features PCIE_TEGRA194_EP must be
 	  selected. This uses the DesignWare core.
 
+config PCIE_VISCONTI_HOST
+	bool "Toshiba Visconti PCIe controllers"
+	depends on ARCH_VISCONTI || COMPILE_TEST
+	depends on PCI_MSI_IRQ_DOMAIN
+	select PCIE_DW_HOST
+	help
+	  Say Y here if you want PCIe controller support on Toshiba Visconti SoC.
+	  This driver supports TMPV7708 SoC.
+
 config PCIE_UNIPHIER
 	bool "Socionext UniPhier PCIe host controllers"
 	depends on ARCH_UNIPHIER || COMPILE_TEST
diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
index eca805c1a023..0b569d54deb3 100644
--- a/drivers/pci/controller/dwc/Makefile
+++ b/drivers/pci/controller/dwc/Makefile
@@ -20,6 +20,7 @@ obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
 obj-$(CONFIG_PCI_MESON) += pci-meson.o
 obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
 obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
+obj-$(CONFIG_PCIE_VISCONTI_HOST) += pcie-visconti.o
 
 # The following drivers are for devices that use the generic ACPI
 # pci_root.c driver but don't support standard ECAM config access.
diff --git a/drivers/pci/controller/dwc/pcie-visconti.c b/drivers/pci/controller/dwc/pcie-visconti.c
new file mode 100644
index 000000000000..b764334f32e6
--- /dev/null
+++ b/drivers/pci/controller/dwc/pcie-visconti.c
@@ -0,0 +1,369 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * DWC PCIe RC driver for Toshiba Visconti ARM SoC
+ *
+ * Copyright (C) 2021 Toshiba Electronic Device & Storage Corporation
+ * Copyright (C) 2021 TOSHIBA CORPORATION
+ *
+ * Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/gpio.h>
+#include <linux/interrupt.h>
+#include <linux/init.h>
+#include <linux/iopoll.h>
+#include <linux/kernel.h>
+#include <linux/of_platform.h>
+#include <linux/pci.h>
+#include <linux/platform_device.h>
+#include <linux/resource.h>
+#include <linux/types.h>
+
+#include "pcie-designware.h"
+#include "../../pci.h"
+
+struct visconti_pcie {
+	struct dw_pcie pci;
+	void __iomem *ulreg_base;
+	void __iomem *smu_base;
+	void __iomem *mpu_base;
+	struct clk *refclk;
+	struct clk *sysclk;
+	struct clk *auxclk;
+};
+
+#define PCIE_UL_REG_S_PCIE_MODE		0x00F4
+#define  PCIE_UL_REG_S_PCIE_MODE_EP	0x00
+#define  PCIE_UL_REG_S_PCIE_MODE_RC	0x04
+
+#define PCIE_UL_REG_S_PERSTN_CTRL	0x00F8
+#define  PCIE_UL_IOM_PCIE_PERSTN_I_EN	BIT(3)
+#define  PCIE_UL_DIRECT_PERSTN_EN	BIT(2)
+#define  PCIE_UL_PERSTN_OUT		BIT(1)
+#define  PCIE_UL_DIRECT_PERSTN		BIT(0)
+#define  PCIE_UL_REG_S_PERSTN_CTRL_INIT	(PCIE_UL_IOM_PCIE_PERSTN_I_EN | \
+					 PCIE_UL_DIRECT_PERSTN_EN | \
+					 PCIE_UL_DIRECT_PERSTN)
+
+#define PCIE_UL_REG_S_PHY_INIT_02	0x0104
+#define  PCIE_UL_PHY0_SRAM_EXT_LD_DONE	BIT(0)
+
+#define PCIE_UL_REG_S_PHY_INIT_03	0x0108
+#define  PCIE_UL_PHY0_SRAM_INIT_DONE	BIT(0)
+
+#define PCIE_UL_REG_S_INT_EVENT_MASK1	0x0138
+#define  PCIE_UL_CFG_PME_INT		BIT(0)
+#define  PCIE_UL_CFG_LINK_EQ_REQ_INT	BIT(1)
+#define  PCIE_UL_EDMA_INT0		BIT(2)
+#define  PCIE_UL_EDMA_INT1		BIT(3)
+#define  PCIE_UL_EDMA_INT2		BIT(4)
+#define  PCIE_UL_EDMA_INT3		BIT(5)
+#define  PCIE_UL_S_INT_EVENT_MASK1_ALL  (PCIE_UL_CFG_PME_INT | \
+					 PCIE_UL_CFG_LINK_EQ_REQ_INT | \
+					 PCIE_UL_EDMA_INT0 | \
+					 PCIE_UL_EDMA_INT1 | \
+					 PCIE_UL_EDMA_INT2 | \
+					 PCIE_UL_EDMA_INT3)
+
+#define PCIE_UL_REG_S_SB_MON		0x0198
+#define PCIE_UL_REG_S_SIG_MON		0x019C
+#define  PCIE_UL_CORE_RST_N_MON		BIT(0)
+
+#define PCIE_UL_REG_V_SII_DBG_00	0x0844
+#define PCIE_UL_REG_V_SII_GEN_CTRL_01	0x0860
+#define  PCIE_UL_APP_LTSSM_ENABLE	BIT(0)
+
+#define PCIE_UL_REG_V_PHY_ST_00		0x0864
+#define  PCIE_UL_SMLH_LINK_UP		BIT(0)
+
+#define PCIE_UL_REG_V_PHY_ST_02		0x0868
+#define  PCIE_UL_S_DETECT_ACT		0x01
+#define  PCIE_UL_S_L0			0x11
+
+#define PISMU_CKON_PCIE			0x0038
+#define  PISMU_CKON_PCIE_AUX_CLK	BIT(1)
+#define  PISMU_CKON_PCIE_MSTR_ACLK	BIT(0)
+
+#define PISMU_RSOFF_PCIE		0x0538
+#define  PISMU_RSOFF_PCIE_ULREG_RST_N	BIT(1)
+#define  PISMU_RSOFF_PCIE_PWR_UP_RST_N	BIT(0)
+
+#define PCIE_MPU_REG_MP_EN		0x0
+#define  MPU_MP_EN_DISABLE		BIT(0)
+
+#define PCIE_BUS_OFFSET			0x40000000
+
+/* Access registers in PCIe ulreg */
+static void visconti_ulreg_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
+{
+	writel_relaxed(val, pcie->ulreg_base + reg);
+}
+
+static u32 visconti_ulreg_readl(struct visconti_pcie *pcie, u32 reg)
+{
+	return readl_relaxed(pcie->ulreg_base + reg);
+}
+
+/* Access registers in PCIe smu */
+static void visconti_smu_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
+{
+	writel_relaxed(val, pcie->smu_base + reg);
+}
+
+/* Access registers in PCIe mpu */
+static void visconti_mpu_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
+{
+	writel_relaxed(val, pcie->mpu_base + reg);
+}
+
+static u32 visconti_mpu_readl(struct visconti_pcie *pcie, u32 reg)
+{
+	return readl_relaxed(pcie->mpu_base + reg);
+}
+
+static int visconti_pcie_link_up(struct dw_pcie *pci)
+{
+	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
+	void __iomem *addr = pcie->ulreg_base;
+	int ret;
+	u32 val;
+
+	/* wait for linkup of phy link layer */
+	ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_00,
+					 val, (val & PCIE_UL_SMLH_LINK_UP),
+					 90000, 100000);
+	if (ret)
+		return 0;
+
+	/* wait for linkup of data link layer */
+	ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_02,
+					 val, (val & PCIE_UL_S_DETECT_ACT),
+					 90000, 100000);
+	if (ret)
+		return 0;
+
+	/* wait for LTSSM Status */
+	ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_02,
+					 val, (val & PCIE_UL_S_L0),
+					 90000, 100000);
+	if (ret)
+		return 0;
+	return 1;
+}
+
+static int visconti_pcie_start_link(struct dw_pcie *pci)
+{
+	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
+
+	visconti_ulreg_writel(pcie, PCIE_UL_APP_LTSSM_ENABLE,
+			      PCIE_UL_REG_V_SII_GEN_CTRL_01);
+
+	if (dw_pcie_link_up(pci)) {
+		u32 val;
+
+		val = visconti_mpu_readl(pcie, PCIE_MPU_REG_MP_EN);
+		visconti_mpu_writel(pcie, val & ~MPU_MP_EN_DISABLE,
+				    PCIE_MPU_REG_MP_EN);
+		visconti_ulreg_writel(pcie, PCIE_UL_S_INT_EVENT_MASK1_ALL,
+				      PCIE_UL_REG_S_INT_EVENT_MASK1);
+	}
+
+	return 0;
+}
+
+static void visconti_pcie_stop_link(struct dw_pcie *pci)
+{
+	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
+	u32 val;
+
+	val = visconti_ulreg_readl(pcie, PCIE_UL_REG_V_SII_GEN_CTRL_01);
+	val &= ~PCIE_UL_APP_LTSSM_ENABLE;
+	visconti_ulreg_writel(pcie, val, PCIE_UL_REG_V_SII_GEN_CTRL_01);
+
+	val = visconti_mpu_readl(pcie, PCIE_MPU_REG_MP_EN);
+	visconti_mpu_writel(pcie, val | MPU_MP_EN_DISABLE, PCIE_MPU_REG_MP_EN);
+}
+
+static u64 visconti_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr)
+{
+	return pci_addr - PCIE_BUS_OFFSET;
+}
+
+static const struct dw_pcie_ops dw_pcie_ops = {
+	.cpu_addr_fixup = visconti_pcie_cpu_addr_fixup,
+	.link_up = visconti_pcie_link_up,
+	.start_link = visconti_pcie_start_link,
+	.stop_link = visconti_pcie_stop_link,
+};
+
+static int visconti_pcie_power_on(struct visconti_pcie *pcie)
+{
+	void __iomem *addr;
+	int err;
+	u32 val;
+
+	visconti_smu_writel(pcie,
+			    PISMU_CKON_PCIE_AUX_CLK | PISMU_CKON_PCIE_MSTR_ACLK,
+			    PISMU_CKON_PCIE);
+	ndelay(250);
+
+	visconti_smu_writel(pcie, PISMU_RSOFF_PCIE_ULREG_RST_N,
+			    PISMU_RSOFF_PCIE);
+	visconti_ulreg_writel(pcie, PCIE_UL_REG_S_PCIE_MODE_RC,
+			      PCIE_UL_REG_S_PCIE_MODE);
+
+	val = PCIE_UL_REG_S_PERSTN_CTRL_INIT;
+	visconti_ulreg_writel(pcie, val, PCIE_UL_REG_S_PERSTN_CTRL);
+	udelay(100);
+
+	val |= PCIE_UL_PERSTN_OUT;
+	visconti_ulreg_writel(pcie, val, PCIE_UL_REG_S_PERSTN_CTRL);
+	udelay(100);
+
+	visconti_smu_writel(pcie, PISMU_RSOFF_PCIE_PWR_UP_RST_N,
+			    PISMU_RSOFF_PCIE);
+
+	addr = pcie->ulreg_base + PCIE_UL_REG_S_PHY_INIT_03;
+	err = readl_relaxed_poll_timeout(addr, val,
+					 (val & PCIE_UL_PHY0_SRAM_INIT_DONE),
+					 100, 1000);
+	if (err)
+		return err;
+
+	visconti_ulreg_writel(pcie, PCIE_UL_PHY0_SRAM_EXT_LD_DONE,
+			      PCIE_UL_REG_S_PHY_INIT_02);
+
+	addr = pcie->ulreg_base + PCIE_UL_REG_S_SIG_MON;
+	return readl_relaxed_poll_timeout(addr, val,
+					  (val & PCIE_UL_CORE_RST_N_MON), 100,
+					  1000);
+}
+
+static int visconti_pcie_host_init(struct pcie_port *pp)
+{
+	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
+	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
+
+	return visconti_pcie_power_on(pcie);
+}
+
+static const struct dw_pcie_host_ops visconti_pcie_host_ops = {
+	.host_init = visconti_pcie_host_init,
+};
+
+static int visconti_get_resources(struct platform_device *pdev,
+				  struct visconti_pcie *pcie)
+{
+	struct device *dev = &pdev->dev;
+
+	pcie->ulreg_base = devm_platform_ioremap_resource_byname(pdev, "ulreg");
+	if (IS_ERR(pcie->ulreg_base))
+		return PTR_ERR(pcie->ulreg_base);
+
+	pcie->smu_base = devm_platform_ioremap_resource_byname(pdev, "smu");
+	if (IS_ERR(pcie->smu_base))
+		return PTR_ERR(pcie->smu_base);
+
+	pcie->mpu_base = devm_platform_ioremap_resource_byname(pdev, "mpu");
+	if (IS_ERR(pcie->mpu_base))
+		return PTR_ERR(pcie->mpu_base);
+
+	pcie->refclk = devm_clk_get(dev, "pcie_refclk");
+	if (IS_ERR(pcie->refclk)) {
+		dev_err(dev, "Failed to get refclk clock: %ld\n",
+			PTR_ERR(pcie->refclk));
+		return PTR_ERR(pcie->refclk);
+	}
+
+	pcie->sysclk = devm_clk_get(dev, "sysclk");
+	if (IS_ERR(pcie->sysclk)) {
+		dev_err(dev, "Failed to get sysclk clock: %ld\n",
+			PTR_ERR(pcie->sysclk));
+		return PTR_ERR(pcie->sysclk);
+	}
+
+	pcie->auxclk = devm_clk_get(dev, "auxclk");
+	if (IS_ERR(pcie->auxclk)) {
+		dev_err(dev, "Failed to get auxclk clock: %ld\n",
+			PTR_ERR(pcie->auxclk));
+		return PTR_ERR(pcie->auxclk);
+	}
+
+	return 0;
+}
+
+static int
+visconti_add_pcie_port(struct visconti_pcie *pcie, struct platform_device *pdev)
+{
+	struct dw_pcie *pci = &pcie->pci;
+	struct pcie_port *pp = &pci->pp;
+	struct device *dev = &pdev->dev;
+
+	pp->irq = platform_get_irq_byname(pdev, "intr");
+	if (pp->irq < 0) {
+		dev_err(dev, "Interrupt intr is missing");
+		return pp->irq;
+	}
+
+	pp->ops = &visconti_pcie_host_ops;
+
+	pci->link_gen = of_pci_get_max_link_speed(pdev->dev.of_node);
+	if (pci->link_gen < 0 || pci->link_gen > 3) {
+		pci->link_gen = 3;
+		dev_dbg(dev, "Applied default link speed\n");
+	}
+
+	dev_dbg(dev, "Link speed Gen %d", pci->link_gen);
+
+	return dw_pcie_host_init(pp);
+}
+
+static int visconti_pcie_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct visconti_pcie *pcie;
+	struct pcie_port *pp;
+	struct dw_pcie *pci;
+	int ret;
+
+	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(36));
+	if (ret)
+		return ret;
+
+	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
+	if (!pcie)
+		return -ENOMEM;
+
+	pci = &pcie->pci;
+	pp = &pci->pp;
+	pp->num_vectors = MAX_MSI_IRQS;
+
+	pci->dev = dev;
+	pci->ops = &dw_pcie_ops;
+
+	ret = visconti_get_resources(pdev, pcie);
+	if (ret)
+		return ret;
+
+	platform_set_drvdata(pdev, pcie);
+
+	return visconti_add_pcie_port(pcie, pdev);
+}
+
+static const struct of_device_id visconti_pcie_match[] = {
+	{ .compatible = "toshiba,visconti-pcie" },
+	{},
+};
+
+static struct platform_driver visconti_pcie_driver = {
+	.probe = visconti_pcie_probe,
+	.driver = {
+		.name = "visconti-pcie",
+		.of_match_table = visconti_pcie_match,
+		.suppress_bind_attrs = true,
+	},
+};
+
+builtin_platform_driver(visconti_pcie_driver);
-- 
2.31.1

[PATCH v3 3/3] MAINTAINERS: Add entries for Toshiba Visconti PCIe controller

[Nobuhiro Iwamatsu]

Add entries for Toshiba Visconti PCIe controller binding and driver.

Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
---
 MAINTAINERS | 2 ++
 1 file changed, 2 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index bd7aff0c120f..8554e02de0cc 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -2663,11 +2663,13 @@ T:	git git://git.kernel.org/pub/scm/linux/kernel/git/iwamatsu/linux-visconti.git
 F:	Documentation/devicetree/bindings/arm/toshiba.yaml
 F:	Documentation/devicetree/bindings/net/toshiba,visconti-dwmac.yaml
 F:	Documentation/devicetree/bindings/gpio/toshiba,gpio-visconti.yaml
+F:	Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
 F:	Documentation/devicetree/bindings/pinctrl/toshiba,tmpv7700-pinctrl.yaml
 F:	Documentation/devicetree/bindings/watchdog/toshiba,visconti-wdt.yaml
 F:	arch/arm64/boot/dts/toshiba/
 F:	drivers/net/ethernet/stmicro/stmmac/dwmac-visconti.c
 F:	drivers/gpio/gpio-visconti.c
+F:	drivers/pci/controller/dwc/pcie-visconti.c
 F:	drivers/pinctrl/visconti/
 F:	drivers/watchdog/visconti_wdt.c
 N:	visconti
-- 
2.31.1

Re: [PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Krzysztof Wilczyński]

Hi Nobuhiro,

Thank you for working on this!

[...]
> +static int visconti_get_resources(struct platform_device *pdev,
> +				  struct visconti_pcie *pcie)
> +{
[...]
> +	pcie->refclk = devm_clk_get(dev, "pcie_refclk");
> +	if (IS_ERR(pcie->refclk)) {
> +		dev_err(dev, "Failed to get refclk clock: %ld\n",
> +			PTR_ERR(pcie->refclk));
> +		return PTR_ERR(pcie->refclk);
> +	}
> +
> +	pcie->sysclk = devm_clk_get(dev, "sysclk");
> +	if (IS_ERR(pcie->sysclk)) {
> +		dev_err(dev, "Failed to get sysclk clock: %ld\n",
> +			PTR_ERR(pcie->sysclk));
> +		return PTR_ERR(pcie->sysclk);
> +	}
> +
> +	pcie->auxclk = devm_clk_get(dev, "auxclk");
> +	if (IS_ERR(pcie->auxclk)) {
> +		dev_err(dev, "Failed to get auxclk clock: %ld\n",
> +			PTR_ERR(pcie->auxclk));
> +		return PTR_ERR(pcie->auxclk);
> +	}

Do you think you could use the dev_err_probe() to handle the
devm_clk_get() failed?  Where applicable this is becoming a common
patter drivers apply, for example:

  pcie->refclk = devm_clk_get(dev, "pcie_refclk");
  if (IS_ERR(pcie->refclk))
  	return dev_err_probe(dev, PTR_ERR(pcie->refclk),
			     "failed to get refclk clock\n");

[...]
> +	pci->link_gen = of_pci_get_max_link_speed(pdev->dev.of_node);
> +	if (pci->link_gen < 0 || pci->link_gen > 3) {
> +		pci->link_gen = 3;
> +		dev_dbg(dev, "Applied default link speed\n");
> +	}
> +
> +	dev_dbg(dev, "Link speed Gen %d", pci->link_gen);

Question about the above debug messages.

Given that both are at the same level and the link speed will be printed
regardless of whether it was set to a default value or not, does it make
sense to still print the message about applying the default link speed?
Unless this is something that will be indeed useful during debugging and
troubleshooting (and in which case just ignore this question).

	Krzysztof

Re: [PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Bjorn Helgaas]

[+cc Kishon for cpu_addr_fixup() question]

Please make the subject "PCI: visconti: Add ..." since the driver
names are usually lower-case.  When referring to the hardware itself,
use "Visconti", of course.

On Mon, May 24, 2021 at 03:30:03PM +0900, Nobuhiro Iwamatsu wrote:
> Add support to PCIe RC controller on Toshiba Visconti ARM SoCs. PCIe
> controller is based of Synopsys DesignWare PCIe core.
> 
> This patch does not yet use the clock framework to control the clock.
> This will be replaced in the future.
> 
> v2 -> v3:
>   - Update subject.
>   - Wrap description in 75 columns.
>   - Change config name to PCIE_VISCONTI_HOST.
>   - Update Kconfig text.
>   - Drop blank lines.
>   - Adjusted to 80 columns.
>   - Drop inline from functions for register access.
>   - Changed function name from visconti_pcie_check_link_status to
>     visconti_pcie_link_up.
>   - Update to using dw_pcie_host_init().
>   - Reorder these in the order of use in visconti_pcie_establish_link.
>   - Rewrite visconti_pcie_host_init() without dw_pcie_setup_rc().
>   - Change function name from  visconti_device_turnon() to
>     visconti_pcie_power_on().
>   - Unify formats such as dev_err().
>   - Drop error label in visconti_add_pcie_port().
> 
> v1 -> v2:
>   - Fix typo in commit message.
>   - Drop "depends on OF && HAS_IOMEM" from Kconfig.
>   - Stop using the pointer of struct dw_pcie.
>   - Use _relaxed variant.
>   - Drop dw_pcie_wait_for_link.
>   - Drop dbi resource processing.
>   - Drop MSI IRQ initialization processing.

Thanks for the changelog.  Please move it after the "---" line for
future versions.  That way it won't appear in the commit log when this
is merged.  The notes about v1->v2, v2->v3, etc are useful during
review, but not after this is merged.

> Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> ---
>  drivers/pci/controller/dwc/Kconfig         |   9 +
>  drivers/pci/controller/dwc/Makefile        |   1 +
>  drivers/pci/controller/dwc/pcie-visconti.c | 369 +++++++++++++++++++++
>  3 files changed, 379 insertions(+)
>  create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c
> 
> diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> index 423d35872ce4..7c3dcb86fcad 100644
> --- a/drivers/pci/controller/dwc/Kconfig
> +++ b/drivers/pci/controller/dwc/Kconfig
> @@ -286,6 +286,15 @@ config PCIE_TEGRA194_EP
>  	  in order to enable device-specific features PCIE_TEGRA194_EP must be
>  	  selected. This uses the DesignWare core.
>  
> +config PCIE_VISCONTI_HOST
> +	bool "Toshiba Visconti PCIe controllers"
> +	depends on ARCH_VISCONTI || COMPILE_TEST
> +	depends on PCI_MSI_IRQ_DOMAIN
> +	select PCIE_DW_HOST
> +	help
> +	  Say Y here if you want PCIe controller support on Toshiba Visconti SoC.
> +	  This driver supports TMPV7708 SoC.
> +
>  config PCIE_UNIPHIER
>  	bool "Socionext UniPhier PCIe host controllers"
>  	depends on ARCH_UNIPHIER || COMPILE_TEST
> diff --git a/drivers/pci/controller/dwc/Makefile b/drivers/pci/controller/dwc/Makefile
> index eca805c1a023..0b569d54deb3 100644
> --- a/drivers/pci/controller/dwc/Makefile
> +++ b/drivers/pci/controller/dwc/Makefile
> @@ -20,6 +20,7 @@ obj-$(CONFIG_PCIE_HISI_STB) += pcie-histb.o
>  obj-$(CONFIG_PCI_MESON) += pci-meson.o
>  obj-$(CONFIG_PCIE_UNIPHIER) += pcie-uniphier.o
>  obj-$(CONFIG_PCIE_UNIPHIER_EP) += pcie-uniphier-ep.o
> +obj-$(CONFIG_PCIE_VISCONTI_HOST) += pcie-visconti.o
>  
>  # The following drivers are for devices that use the generic ACPI
>  # pci_root.c driver but don't support standard ECAM config access.
> diff --git a/drivers/pci/controller/dwc/pcie-visconti.c b/drivers/pci/controller/dwc/pcie-visconti.c
> new file mode 100644
> index 000000000000..b764334f32e6
> --- /dev/null
> +++ b/drivers/pci/controller/dwc/pcie-visconti.c
> @@ -0,0 +1,369 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * DWC PCIe RC driver for Toshiba Visconti ARM SoC
> + *
> + * Copyright (C) 2021 Toshiba Electronic Device & Storage Corporation
> + * Copyright (C) 2021 TOSHIBA CORPORATION
> + *
> + * Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> + */
> +
> +#include <linux/clk.h>
> +#include <linux/delay.h>
> +#include <linux/gpio.h>
> +#include <linux/interrupt.h>
> +#include <linux/init.h>
> +#include <linux/iopoll.h>
> +#include <linux/kernel.h>
> +#include <linux/of_platform.h>
> +#include <linux/pci.h>
> +#include <linux/platform_device.h>
> +#include <linux/resource.h>
> +#include <linux/types.h>
> +
> +#include "pcie-designware.h"
> +#include "../../pci.h"
> +
> +struct visconti_pcie {
> +	struct dw_pcie pci;
> +	void __iomem *ulreg_base;
> +	void __iomem *smu_base;
> +	void __iomem *mpu_base;
> +	struct clk *refclk;
> +	struct clk *sysclk;
> +	struct clk *auxclk;
> +};
> +
> +#define PCIE_UL_REG_S_PCIE_MODE		0x00F4
> +#define  PCIE_UL_REG_S_PCIE_MODE_EP	0x00
> +#define  PCIE_UL_REG_S_PCIE_MODE_RC	0x04
> +
> +#define PCIE_UL_REG_S_PERSTN_CTRL	0x00F8
> +#define  PCIE_UL_IOM_PCIE_PERSTN_I_EN	BIT(3)
> +#define  PCIE_UL_DIRECT_PERSTN_EN	BIT(2)
> +#define  PCIE_UL_PERSTN_OUT		BIT(1)
> +#define  PCIE_UL_DIRECT_PERSTN		BIT(0)
> +#define  PCIE_UL_REG_S_PERSTN_CTRL_INIT	(PCIE_UL_IOM_PCIE_PERSTN_I_EN | \
> +					 PCIE_UL_DIRECT_PERSTN_EN | \
> +					 PCIE_UL_DIRECT_PERSTN)
> +
> +#define PCIE_UL_REG_S_PHY_INIT_02	0x0104
> +#define  PCIE_UL_PHY0_SRAM_EXT_LD_DONE	BIT(0)
> +
> +#define PCIE_UL_REG_S_PHY_INIT_03	0x0108
> +#define  PCIE_UL_PHY0_SRAM_INIT_DONE	BIT(0)
> +
> +#define PCIE_UL_REG_S_INT_EVENT_MASK1	0x0138
> +#define  PCIE_UL_CFG_PME_INT		BIT(0)
> +#define  PCIE_UL_CFG_LINK_EQ_REQ_INT	BIT(1)
> +#define  PCIE_UL_EDMA_INT0		BIT(2)
> +#define  PCIE_UL_EDMA_INT1		BIT(3)
> +#define  PCIE_UL_EDMA_INT2		BIT(4)
> +#define  PCIE_UL_EDMA_INT3		BIT(5)
> +#define  PCIE_UL_S_INT_EVENT_MASK1_ALL  (PCIE_UL_CFG_PME_INT | \
> +					 PCIE_UL_CFG_LINK_EQ_REQ_INT | \
> +					 PCIE_UL_EDMA_INT0 | \
> +					 PCIE_UL_EDMA_INT1 | \
> +					 PCIE_UL_EDMA_INT2 | \
> +					 PCIE_UL_EDMA_INT3)
> +
> +#define PCIE_UL_REG_S_SB_MON		0x0198
> +#define PCIE_UL_REG_S_SIG_MON		0x019C
> +#define  PCIE_UL_CORE_RST_N_MON		BIT(0)
> +
> +#define PCIE_UL_REG_V_SII_DBG_00	0x0844
> +#define PCIE_UL_REG_V_SII_GEN_CTRL_01	0x0860
> +#define  PCIE_UL_APP_LTSSM_ENABLE	BIT(0)
> +
> +#define PCIE_UL_REG_V_PHY_ST_00		0x0864
> +#define  PCIE_UL_SMLH_LINK_UP		BIT(0)
> +
> +#define PCIE_UL_REG_V_PHY_ST_02		0x0868
> +#define  PCIE_UL_S_DETECT_ACT		0x01
> +#define  PCIE_UL_S_L0			0x11
> +
> +#define PISMU_CKON_PCIE			0x0038
> +#define  PISMU_CKON_PCIE_AUX_CLK	BIT(1)
> +#define  PISMU_CKON_PCIE_MSTR_ACLK	BIT(0)
> +
> +#define PISMU_RSOFF_PCIE		0x0538
> +#define  PISMU_RSOFF_PCIE_ULREG_RST_N	BIT(1)
> +#define  PISMU_RSOFF_PCIE_PWR_UP_RST_N	BIT(0)
> +
> +#define PCIE_MPU_REG_MP_EN		0x0
> +#define  MPU_MP_EN_DISABLE		BIT(0)
> +
> +#define PCIE_BUS_OFFSET			0x40000000
> +
> +/* Access registers in PCIe ulreg */
> +static void visconti_ulreg_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
> +{
> +	writel_relaxed(val, pcie->ulreg_base + reg);
> +}
> +
> +static u32 visconti_ulreg_readl(struct visconti_pcie *pcie, u32 reg)
> +{
> +	return readl_relaxed(pcie->ulreg_base + reg);
> +}
> +
> +/* Access registers in PCIe smu */
> +static void visconti_smu_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
> +{
> +	writel_relaxed(val, pcie->smu_base + reg);
> +}
> +
> +/* Access registers in PCIe mpu */
> +static void visconti_mpu_writel(struct visconti_pcie *pcie, u32 val, u32 reg)
> +{
> +	writel_relaxed(val, pcie->mpu_base + reg);
> +}
> +
> +static u32 visconti_mpu_readl(struct visconti_pcie *pcie, u32 reg)
> +{
> +	return readl_relaxed(pcie->mpu_base + reg);
> +}
> +
> +static int visconti_pcie_link_up(struct dw_pcie *pci)
> +{
> +	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> +	void __iomem *addr = pcie->ulreg_base;
> +	int ret;
> +	u32 val;
> +
> +	/* wait for linkup of phy link layer */
> +	ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_00,
> +					 val, (val & PCIE_UL_SMLH_LINK_UP),
> +					 90000, 100000);
> +	if (ret)
> +		return 0;
> +
> +	/* wait for linkup of data link layer */
> +	ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_02,
> +					 val, (val & PCIE_UL_S_DETECT_ACT),
> +					 90000, 100000);
> +	if (ret)
> +		return 0;
> +
> +	/* wait for LTSSM Status */
> +	ret = readl_relaxed_poll_timeout(addr + PCIE_UL_REG_V_PHY_ST_02,
> +					 val, (val & PCIE_UL_S_L0),
> +					 90000, 100000);
> +	if (ret)
> +		return 0;
> +	return 1;
> +}
> +
> +static int visconti_pcie_start_link(struct dw_pcie *pci)
> +{
> +	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> +
> +	visconti_ulreg_writel(pcie, PCIE_UL_APP_LTSSM_ENABLE,
> +			      PCIE_UL_REG_V_SII_GEN_CTRL_01);
> +
> +	if (dw_pcie_link_up(pci)) {
> +		u32 val;
> +
> +		val = visconti_mpu_readl(pcie, PCIE_MPU_REG_MP_EN);
> +		visconti_mpu_writel(pcie, val & ~MPU_MP_EN_DISABLE,
> +				    PCIE_MPU_REG_MP_EN);
> +		visconti_ulreg_writel(pcie, PCIE_UL_S_INT_EVENT_MASK1_ALL,
> +				      PCIE_UL_REG_S_INT_EVENT_MASK1);
> +	}
> +
> +	return 0;
> +}
> +
> +static void visconti_pcie_stop_link(struct dw_pcie *pci)
> +{
> +	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> +	u32 val;
> +
> +	val = visconti_ulreg_readl(pcie, PCIE_UL_REG_V_SII_GEN_CTRL_01);
> +	val &= ~PCIE_UL_APP_LTSSM_ENABLE;
> +	visconti_ulreg_writel(pcie, val, PCIE_UL_REG_V_SII_GEN_CTRL_01);
> +
> +	val = visconti_mpu_readl(pcie, PCIE_MPU_REG_MP_EN);
> +	visconti_mpu_writel(pcie, val | MPU_MP_EN_DISABLE, PCIE_MPU_REG_MP_EN);
> +}
> +
> +static u64 visconti_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr)
> +{
> +	return pci_addr - PCIE_BUS_OFFSET;

This is called from __dw_pcie_prog_outbound_atu() as:

  cpu_addr = pci->ops->cpu_addr_fixup(pci, cpu_addr);

so I think the parameter here should be *cpu_addr*, not pci_addr.

dra7xx and artpec6 also call it "pci_addr", which is at best
confusing.

I'm also confused about exactly what .cpu_addr_fixup() does.  Is it
applying an offset that cannot be deduced from the DT description?  If
so, *should* this offset be described in DT?

> +}
> +
> +static const struct dw_pcie_ops dw_pcie_ops = {
> +	.cpu_addr_fixup = visconti_pcie_cpu_addr_fixup,
> +	.link_up = visconti_pcie_link_up,
> +	.start_link = visconti_pcie_start_link,
> +	.stop_link = visconti_pcie_stop_link,
> +};
> +
> +static int visconti_pcie_power_on(struct visconti_pcie *pcie)
> +{
> +	void __iomem *addr;
> +	int err;
> +	u32 val;
> +
> +	visconti_smu_writel(pcie,
> +			    PISMU_CKON_PCIE_AUX_CLK | PISMU_CKON_PCIE_MSTR_ACLK,
> +			    PISMU_CKON_PCIE);
> +	ndelay(250);
> +
> +	visconti_smu_writel(pcie, PISMU_RSOFF_PCIE_ULREG_RST_N,
> +			    PISMU_RSOFF_PCIE);
> +	visconti_ulreg_writel(pcie, PCIE_UL_REG_S_PCIE_MODE_RC,
> +			      PCIE_UL_REG_S_PCIE_MODE);
> +
> +	val = PCIE_UL_REG_S_PERSTN_CTRL_INIT;
> +	visconti_ulreg_writel(pcie, val, PCIE_UL_REG_S_PERSTN_CTRL);
> +	udelay(100);
> +
> +	val |= PCIE_UL_PERSTN_OUT;
> +	visconti_ulreg_writel(pcie, val, PCIE_UL_REG_S_PERSTN_CTRL);
> +	udelay(100);
> +
> +	visconti_smu_writel(pcie, PISMU_RSOFF_PCIE_PWR_UP_RST_N,
> +			    PISMU_RSOFF_PCIE);
> +
> +	addr = pcie->ulreg_base + PCIE_UL_REG_S_PHY_INIT_03;
> +	err = readl_relaxed_poll_timeout(addr, val,
> +					 (val & PCIE_UL_PHY0_SRAM_INIT_DONE),
> +					 100, 1000);
> +	if (err)
> +		return err;
> +
> +	visconti_ulreg_writel(pcie, PCIE_UL_PHY0_SRAM_EXT_LD_DONE,
> +			      PCIE_UL_REG_S_PHY_INIT_02);
> +
> +	addr = pcie->ulreg_base + PCIE_UL_REG_S_SIG_MON;
> +	return readl_relaxed_poll_timeout(addr, val,
> +					  (val & PCIE_UL_CORE_RST_N_MON), 100,
> +					  1000);
> +}
> +
> +static int visconti_pcie_host_init(struct pcie_port *pp)
> +{
> +	struct dw_pcie *pci = to_dw_pcie_from_pp(pp);
> +	struct visconti_pcie *pcie = dev_get_drvdata(pci->dev);
> +
> +	return visconti_pcie_power_on(pcie);

This bears very little resemblance to the .host_init() functions of
other dwc-based drivers.  It'd be nice if they were more consistent.
But if there are real hardware differences causing these driver
differences, that's ok.  I see a couple (meson, kirin) that call a
*power_on() function from *_pcie_probe().  

> +}
> +
> +static const struct dw_pcie_host_ops visconti_pcie_host_ops = {
> +	.host_init = visconti_pcie_host_init,
> +};
> +
> +static int visconti_get_resources(struct platform_device *pdev,
> +				  struct visconti_pcie *pcie)
> +{
> +	struct device *dev = &pdev->dev;
> +
> +	pcie->ulreg_base = devm_platform_ioremap_resource_byname(pdev, "ulreg");
> +	if (IS_ERR(pcie->ulreg_base))
> +		return PTR_ERR(pcie->ulreg_base);
> +
> +	pcie->smu_base = devm_platform_ioremap_resource_byname(pdev, "smu");
> +	if (IS_ERR(pcie->smu_base))
> +		return PTR_ERR(pcie->smu_base);
> +
> +	pcie->mpu_base = devm_platform_ioremap_resource_byname(pdev, "mpu");
> +	if (IS_ERR(pcie->mpu_base))
> +		return PTR_ERR(pcie->mpu_base);
> +
> +	pcie->refclk = devm_clk_get(dev, "pcie_refclk");
> +	if (IS_ERR(pcie->refclk)) {
> +		dev_err(dev, "Failed to get refclk clock: %ld\n",
> +			PTR_ERR(pcie->refclk));
> +		return PTR_ERR(pcie->refclk);
> +	}
> +
> +	pcie->sysclk = devm_clk_get(dev, "sysclk");
> +	if (IS_ERR(pcie->sysclk)) {
> +		dev_err(dev, "Failed to get sysclk clock: %ld\n",
> +			PTR_ERR(pcie->sysclk));
> +		return PTR_ERR(pcie->sysclk);
> +	}
> +
> +	pcie->auxclk = devm_clk_get(dev, "auxclk");
> +	if (IS_ERR(pcie->auxclk)) {
> +		dev_err(dev, "Failed to get auxclk clock: %ld\n",
> +			PTR_ERR(pcie->auxclk));
> +		return PTR_ERR(pcie->auxclk);
> +	}
> +
> +	return 0;
> +}
> +
> +static int
> +visconti_add_pcie_port(struct visconti_pcie *pcie, struct platform_device *pdev)
> +{
> +	struct dw_pcie *pci = &pcie->pci;
> +	struct pcie_port *pp = &pci->pp;
> +	struct device *dev = &pdev->dev;
> +
> +	pp->irq = platform_get_irq_byname(pdev, "intr");
> +	if (pp->irq < 0) {
> +		dev_err(dev, "Interrupt intr is missing");
> +		return pp->irq;
> +	}

Looks like most drivers use "pp->irq = platform_get_irq(pdev, 0);"
Is there a reason for this to be different?

> +	pp->ops = &visconti_pcie_host_ops;
> +
> +	pci->link_gen = of_pci_get_max_link_speed(pdev->dev.of_node);
> +	if (pci->link_gen < 0 || pci->link_gen > 3) {
> +		pci->link_gen = 3;
> +		dev_dbg(dev, "Applied default link speed\n");
> +	}
> +
> +	dev_dbg(dev, "Link speed Gen %d", pci->link_gen);
> +
> +	return dw_pcie_host_init(pp);
> +}
> +
> +static int visconti_pcie_probe(struct platform_device *pdev)
> +{
> +	struct device *dev = &pdev->dev;
> +	struct visconti_pcie *pcie;
> +	struct pcie_port *pp;
> +	struct dw_pcie *pci;
> +	int ret;
> +
> +	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(36));
> +	if (ret)
> +		return ret;

Somewhat unusual in PCIe controller drivers.  Is there something
unusual about the Visconti hardware?

Also looks a little suspicious since the sequence is:

  visconti_pcie_probe
    dma_set_mask_and_coherent(DMA_BIT_MASK(36))
    visconti_add_pcie_port
      dw_pcie_host_init
        if (pci_msi_enabled())
          dma_set_mask(DMA_BIT_MASK(32))

so dw_pcie_host_init() will override part of what we're setting here.

> +	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> +	if (!pcie)
> +		return -ENOMEM;
> +
> +	pci = &pcie->pci;
> +	pp = &pci->pp;
> +	pp->num_vectors = MAX_MSI_IRQS;

Is this necessary?  I can't tell that this driver even implements MSI
support.  It looks like tegra194 is the only other driver that sets
num_vectors itself.

> +	pci->dev = dev;
> +	pci->ops = &dw_pcie_ops;
> +
> +	ret = visconti_get_resources(pdev, pcie);
> +	if (ret)
> +		return ret;
> +
> +	platform_set_drvdata(pdev, pcie);
> +
> +	return visconti_add_pcie_port(pcie, pdev);
> +}
> +
> +static const struct of_device_id visconti_pcie_match[] = {
> +	{ .compatible = "toshiba,visconti-pcie" },
> +	{},
> +};
> +
> +static struct platform_driver visconti_pcie_driver = {
> +	.probe = visconti_pcie_probe,
> +	.driver = {
> +		.name = "visconti-pcie",
> +		.of_match_table = visconti_pcie_match,
> +		.suppress_bind_attrs = true,
> +	},
> +};
> +
> +builtin_platform_driver(visconti_pcie_driver);
> -- 
> 2.31.1
> 

Re: [PATCH v3 1/3] dt-bindings: pci: Add DT binding for Toshiba Visconti PCIe controller

[Rob Herring]

On Mon, May 24, 2021 at 1:30 AM Nobuhiro Iwamatsu
<nobuhiro1.iwamatsu@toshiba.co.jp> wrote:
>
> This commit adds the Device Tree binding documentation that allows
> to describe the PCIe controller found in Toshiba Visconti SoCs.
>
> v1 -> v2:
>  - Remove white space.
>  - Drop num-viewport and bus-range from required.
>  - Drop status line from example.
>  - Drop bus-range from required.
>  - Removed lines defined in pci-bus.yaml from required.
>
> Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> ---
>  .../bindings/pci/toshiba,visconti-pcie.yaml   | 110 ++++++++++++++++++
>  1 file changed, 110 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml

Please resend to DT list. Otherwise, automated checks don't run
(though I'm sure you ran 'make dt_binding_check' already, right?).

>
> diff --git a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
> new file mode 100644
> index 000000000000..d47a4a3c49e3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
> @@ -0,0 +1,110 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pci/toshiba,visconti-pcie.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Toshiba Visconti5 SoC PCIe Host Controller Device Tree Bindings
> +
> +maintainers:
> +  - Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> +
> +description: |+
> +  Toshiba Visconti5 SoC PCIe host controller is based on the Synopsys DesignWare PCIe IP.
> +
> +allOf:
> +  - $ref: /schemas/pci/pci-bus.yaml#
> +
> +properties:
> +  compatible:
> +    const: toshiba,visconti-pcie
> +
> +  reg:
> +    items:
> +      - description: Data Bus Interface (DBI) registers.
> +      - description: PCIe configuration space region.
> +      - description: Visconti specific additional registers.
> +      - description: Visconti specific SMU registers
> +      - description: Visconti specific memory protection unit registers (MPU)
> +
> +  reg-names:
> +    items:
> +      - const: dbi
> +      - const: config
> +      - const: ulreg
> +      - const: smu
> +      - const: mpu
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    items:
> +      - description: PCIe reference clock
> +      - description: PCIe system clock
> +      - description: Auxiliary clock
> +
> +  clock-names:
> +    items:
> +      - const: pcie_refclk

Just 'refclk'. Though 'clk' is redundant too. I'd go with 'ref',
'aux', and 'core'.

> +      - const: sysclk
> +      - const: auxclk
> +
> +  num-lanes:
> +    const: 2
> +
> +required:
> +  - reg
> +  - reg-names
> +  - interrupts
> +  - "#interrupt-cells"
> +  - interrupt-map
> +  - interrupt-map-mask
> +  - num-lanes
> +  - clocks
> +  - clock-names
> +  - max-link-speed
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +
> +    soc {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        pcie: pcie@28400000 {
> +            compatible = "toshiba,visconti-pcie";
> +            reg = <0x0 0x28400000 0x0 0x00400000>,
> +                  <0x0 0x70000000 0x0 0x10000000>,
> +                  <0x0 0x28050000 0x0 0x00010000>,
> +                  <0x0 0x24200000 0x0 0x00002000>,
> +                  <0x0 0x24162000 0x0 0x00001000>;
> +            reg-names  = "dbi", "config", "ulreg", "smu", "mpu";
> +            device_type = "pci";
> +            bus-range = <0x00 0xff>;
> +            num-lanes = <2>;
> +            num-viewport = <8>;
> +
> +            #address-cells = <3>;
> +            #size-cells = <2>;
> +            #interrupt-cells = <1>;
> +            ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000>,
> +                     <0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>;
> +            interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
> +            interrupt-names = "intr";
> +            interrupt-map-mask = <0 0 0 7>;
> +            interrupt-map =
> +                <0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
> +                 0 0 0 2 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
> +                 0 0 0 3 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
> +                 0 0 0 4 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
> +            clocks = <&extclk100mhz>, <&clk600mhz>, <&clk25mhz>;
> +            clock-names = "pcie_refclk", "sysclk", "auxclk";
> +            max-link-speed = <2>;
> +        };
> +    };
> +...
> --
> 2.31.1
>

Re: [PATCH v3 1/3] dt-bindings: pci: Add DT binding for Toshiba Visconti PCIe controller

[Nobuhiro Iwamatsu]

On Wed, May 26, 2021 at 11:33:35AM -0500, Rob Herring wrote:
> On Mon, May 24, 2021 at 1:30 AM Nobuhiro Iwamatsu
> <nobuhiro1.iwamatsu@toshiba.co.jp> wrote:
> >
> > This commit adds the Device Tree binding documentation that allows
> > to describe the PCIe controller found in Toshiba Visconti SoCs.
> >
> > v1 -> v2:
> >  - Remove white space.
> >  - Drop num-viewport and bus-range from required.
> >  - Drop status line from example.
> >  - Drop bus-range from required.
> >  - Removed lines defined in pci-bus.yaml from required.
> >
> > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > ---
> >  .../bindings/pci/toshiba,visconti-pcie.yaml   | 110 ++++++++++++++++++
> >  1 file changed, 110 insertions(+)
> >  create mode 100644 Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
> 
> Please resend to DT list. Otherwise, automated checks don't run
OK, I will resent to DT list.
> (though I'm sure you ran 'make dt_binding_check' already, right?).

Yes, I ran it enerytime.


> >
> > diff --git a/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
> > new file mode 100644
> > index 000000000000..d47a4a3c49e3
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/pci/toshiba,visconti-pcie.yaml
> > @@ -0,0 +1,110 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/pci/toshiba,visconti-pcie.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: Toshiba Visconti5 SoC PCIe Host Controller Device Tree Bindings
> > +
> > +maintainers:
> > +  - Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > +
> > +description: |+
> > +  Toshiba Visconti5 SoC PCIe host controller is based on the Synopsys DesignWare PCIe IP.
> > +
> > +allOf:
> > +  - $ref: /schemas/pci/pci-bus.yaml#
> > +
> > +properties:
> > +  compatible:
> > +    const: toshiba,visconti-pcie
> > +
> > +  reg:
> > +    items:
> > +      - description: Data Bus Interface (DBI) registers.
> > +      - description: PCIe configuration space region.
> > +      - description: Visconti specific additional registers.
> > +      - description: Visconti specific SMU registers
> > +      - description: Visconti specific memory protection unit registers (MPU)
> > +
> > +  reg-names:
> > +    items:
> > +      - const: dbi
> > +      - const: config
> > +      - const: ulreg
> > +      - const: smu
> > +      - const: mpu
> > +
> > +  interrupts:
> > +    maxItems: 1
> > +
> > +  clocks:
> > +    items:
> > +      - description: PCIe reference clock
> > +      - description: PCIe system clock
> > +      - description: Auxiliary clock
> > +
> > +  clock-names:
> > +    items:
> > +      - const: pcie_refclk
> 
> Just 'refclk'. Though 'clk' is redundant too. I'd go with 'ref',
> 'aux', and 'core'.
> 

Ok, I will update.

> > +      - const: sysclk
> > +      - const: auxclk
> > +
> > +  num-lanes:
> > +    const: 2
> > +
> > +required:
> > +  - reg
> > +  - reg-names
> > +  - interrupts
> > +  - "#interrupt-cells"
> > +  - interrupt-map
> > +  - interrupt-map-mask
> > +  - num-lanes
> > +  - clocks
> > +  - clock-names
> > +  - max-link-speed
> > +
> > +unevaluatedProperties: false
> > +
> > +examples:
> > +  - |
> > +    #include <dt-bindings/interrupt-controller/irq.h>
> > +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> > +
> > +    soc {
> > +        #address-cells = <2>;
> > +        #size-cells = <2>;
> > +
> > +        pcie: pcie@28400000 {
> > +            compatible = "toshiba,visconti-pcie";
> > +            reg = <0x0 0x28400000 0x0 0x00400000>,
> > +                  <0x0 0x70000000 0x0 0x10000000>,
> > +                  <0x0 0x28050000 0x0 0x00010000>,
> > +                  <0x0 0x24200000 0x0 0x00002000>,
> > +                  <0x0 0x24162000 0x0 0x00001000>;
> > +            reg-names  = "dbi", "config", "ulreg", "smu", "mpu";
> > +            device_type = "pci";
> > +            bus-range = <0x00 0xff>;
> > +            num-lanes = <2>;
> > +            num-viewport = <8>;
> > +
> > +            #address-cells = <3>;
> > +            #size-cells = <2>;
> > +            #interrupt-cells = <1>;
> > +            ranges = <0x81000000 0 0x40000000 0 0x40000000 0 0x00010000>,
> > +                     <0x82000000 0 0x50000000 0 0x50000000 0 0x20000000>;
> > +            interrupts = <GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
> > +            interrupt-names = "intr";
> > +            interrupt-map-mask = <0 0 0 7>;
> > +            interrupt-map =
> > +                <0 0 0 1 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
> > +                 0 0 0 2 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
> > +                 0 0 0 3 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH
> > +                 0 0 0 4 &gic GIC_SPI 215 IRQ_TYPE_LEVEL_HIGH>;
> > +            clocks = <&extclk100mhz>, <&clk600mhz>, <&clk25mhz>;
> > +            clock-names = "pcie_refclk", "sysclk", "auxclk";
> > +            max-link-speed = <2>;
> > +        };
> > +    };
> > +...
> > --
> > 2.31.1
> >
> 

Best regards,
  Nobuhiro

Re: [PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Nobuhiro Iwamatsu]

Hi, 

Thanks for your review.

On Mon, May 24, 2021 at 01:10:51PM +0200, Krzysztof Wilczyński wrote:
> Hi Nobuhiro,
> 
> Thank you for working on this!
> 
> [...]
> > +static int visconti_get_resources(struct platform_device *pdev,
> > +				  struct visconti_pcie *pcie)
> > +{
> [...]
> > +	pcie->refclk = devm_clk_get(dev, "pcie_refclk");
> > +	if (IS_ERR(pcie->refclk)) {
> > +		dev_err(dev, "Failed to get refclk clock: %ld\n",
> > +			PTR_ERR(pcie->refclk));
> > +		return PTR_ERR(pcie->refclk);
> > +	}
> > +
> > +	pcie->sysclk = devm_clk_get(dev, "sysclk");
> > +	if (IS_ERR(pcie->sysclk)) {
> > +		dev_err(dev, "Failed to get sysclk clock: %ld\n",
> > +			PTR_ERR(pcie->sysclk));
> > +		return PTR_ERR(pcie->sysclk);
> > +	}
> > +
> > +	pcie->auxclk = devm_clk_get(dev, "auxclk");
> > +	if (IS_ERR(pcie->auxclk)) {
> > +		dev_err(dev, "Failed to get auxclk clock: %ld\n",
> > +			PTR_ERR(pcie->auxclk));
> > +		return PTR_ERR(pcie->auxclk);
> > +	}
> 
> Do you think you could use the dev_err_probe() to handle the
> devm_clk_get() failed?  Where applicable this is becoming a common
> patter drivers apply, for example:
> 
>   pcie->refclk = devm_clk_get(dev, "pcie_refclk");
>   if (IS_ERR(pcie->refclk))
>   	return dev_err_probe(dev, PTR_ERR(pcie->refclk),
> 			     "failed to get refclk clock\n");
> 
> [...]

Thanks for your suggestion. I will fix using dev_err_probe().

> > +	pci->link_gen = of_pci_get_max_link_speed(pdev->dev.of_node);
> > +	if (pci->link_gen < 0 || pci->link_gen > 3) {
> > +		pci->link_gen = 3;
> > +		dev_dbg(dev, "Applied default link speed\n");
> > +	}
> > +
> > +	dev_dbg(dev, "Link speed Gen %d", pci->link_gen);
> 
> Question about the above debug messages.
> 
> Given that both are at the same level and the link speed will be printed
> regardless of whether it was set to a default value or not, does it make
> sense to still print the message about applying the default link speed?
> Unless this is something that will be indeed useful during debugging and
> troubleshooting (and in which case just ignore this question).

I guess so, the message about the default value is not important.
I will remove this, thank you.

Best regards,
  Nobuhiro

Re: [PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Nobuhiro Iwamatsu]

Hi, 

Thanks for your reivew.


On Mon, May 24, 2021 at 01:58:39PM -0500, Bjorn Helgaas wrote:
> [+cc Kishon for cpu_addr_fixup() question]
> 
> Please make the subject "PCI: visconti: Add ..." since the driver
> names are usually lower-case.  When referring to the hardware itself,
> use "Visconti", of course.


OK, I will do so from next time.

> 
> On Mon, May 24, 2021 at 03:30:03PM +0900, Nobuhiro Iwamatsu wrote:
> > Add support to PCIe RC controller on Toshiba Visconti ARM SoCs. PCIe
> > controller is based of Synopsys DesignWare PCIe core.
> > 
> > This patch does not yet use the clock framework to control the clock.
> > This will be replaced in the future.
> > 
> > v2 -> v3:
> >   - Update subject.
> >   - Wrap description in 75 columns.
> >   - Change config name to PCIE_VISCONTI_HOST.
> >   - Update Kconfig text.
> >   - Drop blank lines.
> >   - Adjusted to 80 columns.
> >   - Drop inline from functions for register access.
> >   - Changed function name from visconti_pcie_check_link_status to
> >     visconti_pcie_link_up.
> >   - Update to using dw_pcie_host_init().
> >   - Reorder these in the order of use in visconti_pcie_establish_link.
> >   - Rewrite visconti_pcie_host_init() without dw_pcie_setup_rc().
> >   - Change function name from  visconti_device_turnon() to
> >     visconti_pcie_power_on().
> >   - Unify formats such as dev_err().
> >   - Drop error label in visconti_add_pcie_port().
> > 
> > v1 -> v2:
> >   - Fix typo in commit message.
> >   - Drop "depends on OF && HAS_IOMEM" from Kconfig.
> >   - Stop using the pointer of struct dw_pcie.
> >   - Use _relaxed variant.
> >   - Drop dw_pcie_wait_for_link.
> >   - Drop dbi resource processing.
> >   - Drop MSI IRQ initialization processing.
> 
> Thanks for the changelog.  Please move it after the "---" line for
> future versions.  That way it won't appear in the commit log when this
> is merged.  The notes about v1->v2, v2->v3, etc are useful during
> review, but not after this is merged.


Simliar to the above your comment, I will do so from next time.

> 
> > Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
> > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > ---
> >  drivers/pci/controller/dwc/Kconfig         |   9 +
> >  drivers/pci/controller/dwc/Makefile        |   1 +
> >  drivers/pci/controller/dwc/pcie-visconti.c | 369 +++++++++++++++++++++
> >  3 files changed, 379 insertions(+)
> >  create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c
> > 
> > diff --git a/drivers/pci/controller/dwc/Kconfig b/drivers/pci/controller/dwc/Kconfig
> > index 423d35872ce4..7c3dcb86fcad 100644
> > --- a/drivers/pci/controller/dwc/Kconfig
> > +++ b/drivers/pci/controller/dwc/Kconfig
> > @@ -286,6 +286,15 @@ config PCIE_TEGRA194_EP
> >  	  in order to enable device-specific features PCIE_TEGRA194_EP must be
> >  	  selected. This uses the DesignWare core.
> >  
> > +config PCIE_VISCONTI_HOST
> > +	bool "Toshiba Visconti PCIe controllers"
> > +	depends on ARCH_VISCONTI || COMPILE_TEST
> > +	depends on PCI_MSI_IRQ_DOMAIN
> > +	select PCIE_DW_HOST
> > +	help
> > +	  Say Y here if you want PCIe controller support on Toshiba Visconti SoC.
> > +	  This driver supports TMPV7708 SoC.
> > +

<snip>

> > diff --git a/drivers/pci/controller/dwc/pcie-visconti.c b/drivers/pci/controller/dwc/pcie-visconti.c
> > new file mode 100644
> > index 000000000000..b764334f32e6
> > --- /dev/null
> > +++ b/drivers/pci/controller/dwc/pcie-visconti.c
> > @@ -0,0 +1,369 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * DWC PCIe RC driver for Toshiba Visconti ARM SoC
> > + *
> > + * Copyright (C) 2021 Toshiba Electronic Device & Storage Corporation
> > + * Copyright (C) 2021 TOSHIBA CORPORATION
> > + *
> > + * Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > + */

<snip>

> > +static u64 visconti_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr)
> > +{
> > +	return pci_addr - PCIE_BUS_OFFSET;
> 
> This is called from __dw_pcie_prog_outbound_atu() as:
> 
>   cpu_addr = pci->ops->cpu_addr_fixup(pci, cpu_addr);
> 
> so I think the parameter here should be *cpu_addr*, not pci_addr.

I see, I rename the variable to cpu_addr.

> 
> dra7xx and artpec6 also call it "pci_addr", which is at best
> confusing.
> 
> I'm also confused about exactly what .cpu_addr_fixup() does.  Is it
> applying an offset that cannot be deduced from the DT description?  If
> so, *should* this offset be described in DT?
>

This depends on Visconti5's PCIe hardware implementation.
It depends on the specification that the CPU bus connected to PCIe outputs
with 0x40000000 added as an offset. This is fixed.
I will add this description as comment.

> > +}
> > +
> > +static const struct dw_pcie_ops dw_pcie_ops = {
> > +	.cpu_addr_fixup = visconti_pcie_cpu_addr_fixup,
> > +	.link_up = visconti_pcie_link_up,
> > +	.start_link = visconti_pcie_start_link,
> > +	.stop_link = visconti_pcie_stop_link,
> > +};
> > +
> > +static int visconti_pcie_power_on(struct visconti_pcie *pcie)
> > +{
> > +	void __iomem *addr;
> > +	int err;
> > +	u32 val;
> > +

<snip>

> > +static int
> > +visconti_add_pcie_port(struct visconti_pcie *pcie, struct platform_device *pdev)
> > +{
> > +	struct dw_pcie *pci = &pcie->pci;
> > +	struct pcie_port *pp = &pci->pp;
> > +	struct device *dev = &pdev->dev;
> > +
> > +	pp->irq = platform_get_irq_byname(pdev, "intr");
> > +	if (pp->irq < 0) {
> > +		dev_err(dev, "Interrupt intr is missing");
> > +		return pp->irq;
> > +	}
> 
> Looks like most drivers use "pp->irq = platform_get_irq(pdev, 0);"
> Is there a reason for this to be different?

This driver has two interrupts, msi and usual interrupt.
MSI is handled by the dwc framework, but the rest is handled by the driver.
When When I get the IRQ using index, it may not be processed correctly
depending on how to write DT, so I use platform_get_irq_byname() to check by name.

> 
> > +	pp->ops = &visconti_pcie_host_ops;
> > +
> > +	pci->link_gen = of_pci_get_max_link_speed(pdev->dev.of_node);
> > +	if (pci->link_gen < 0 || pci->link_gen > 3) {
> > +		pci->link_gen = 3;
> > +		dev_dbg(dev, "Applied default link speed\n");
> > +	}
> > +
> > +	dev_dbg(dev, "Link speed Gen %d", pci->link_gen);
> > +
> > +	return dw_pcie_host_init(pp);
> > +}
> > +
> > +static int visconti_pcie_probe(struct platform_device *pdev)
> > +{
> > +	struct device *dev = &pdev->dev;
> > +	struct visconti_pcie *pcie;
> > +	struct pcie_port *pp;
> > +	struct dw_pcie *pci;
> > +	int ret;
> > +
> > +	ret = dma_set_mask_and_coherent(dev, DMA_BIT_MASK(36));
> > +	if (ret)
> > +		return ret;
> 
> Somewhat unusual in PCIe controller drivers.  Is there something
> unusual about the Visconti hardware?
> 
> Also looks a little suspicious since the sequence is:
> 
>   visconti_pcie_probe
>     dma_set_mask_and_coherent(DMA_BIT_MASK(36))
>     visconti_add_pcie_port
>       dw_pcie_host_init
>         if (pci_msi_enabled())
>           dma_set_mask(DMA_BIT_MASK(32))
> 
> so dw_pcie_host_init() will override part of what we're setting here.
> 

Indeed, this process is unnecessary. I will drop.

> > +	pcie = devm_kzalloc(dev, sizeof(*pcie), GFP_KERNEL);
> > +	if (!pcie)
> > +		return -ENOMEM;
> > +
> > +	pci = &pcie->pci;
> > +	pp = &pci->pp;
> > +	pp->num_vectors = MAX_MSI_IRQS;
> 
> Is this necessary?  I can't tell that this driver even implements MSI
> support.  It looks like tegra194 is the only other driver that sets
> num_vectors itself.

This device uses MSI. And I double-checked about interrupts. This device
does not need to do this, as it has a maximum of 32 interrupt vectors.
I will delete it. Thank you for pointing out.

> 
> > +	pci->dev = dev;
> > +	pci->ops = &dw_pcie_ops;
> > +
> > +	ret = visconti_get_resources(pdev, pcie);
> > +	if (ret)
> > +		return ret;
> > +
> > +	platform_set_drvdata(pdev, pcie);
> > +
> > +	return visconti_add_pcie_port(pcie, pdev);
> > +}
> > +
> > +static const struct of_device_id visconti_pcie_match[] = {
> > +	{ .compatible = "toshiba,visconti-pcie" },
> > +	{},
> > +};
> > +
> > +static struct platform_driver visconti_pcie_driver = {
> > +	.probe = visconti_pcie_probe,
> > +	.driver = {
> > +		.name = "visconti-pcie",
> > +		.of_match_table = visconti_pcie_match,
> > +		.suppress_bind_attrs = true,
> > +	},
> > +};
> > +
> > +builtin_platform_driver(visconti_pcie_driver);
> > -- 
> > 2.31.1
> > 
>

Best regards,
  Nobuhiro

Re: [PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Rob Herring]

On Mon, May 24, 2021 at 12:58 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
>
> [+cc Kishon for cpu_addr_fixup() question]
>
> Please make the subject "PCI: visconti: Add ..." since the driver
> names are usually lower-case.  When referring to the hardware itself,
> use "Visconti", of course.
>
> On Mon, May 24, 2021 at 03:30:03PM +0900, Nobuhiro Iwamatsu wrote:
> > Add support to PCIe RC controller on Toshiba Visconti ARM SoCs. PCIe
> > controller is based of Synopsys DesignWare PCIe core.
> >
> > This patch does not yet use the clock framework to control the clock.
> > This will be replaced in the future.
> >
> > v2 -> v3:
> >   - Update subject.
> >   - Wrap description in 75 columns.
> >   - Change config name to PCIE_VISCONTI_HOST.
> >   - Update Kconfig text.
> >   - Drop blank lines.
> >   - Adjusted to 80 columns.
> >   - Drop inline from functions for register access.
> >   - Changed function name from visconti_pcie_check_link_status to
> >     visconti_pcie_link_up.
> >   - Update to using dw_pcie_host_init().
> >   - Reorder these in the order of use in visconti_pcie_establish_link.
> >   - Rewrite visconti_pcie_host_init() without dw_pcie_setup_rc().
> >   - Change function name from  visconti_device_turnon() to
> >     visconti_pcie_power_on().
> >   - Unify formats such as dev_err().
> >   - Drop error label in visconti_add_pcie_port().
> >
> > v1 -> v2:
> >   - Fix typo in commit message.
> >   - Drop "depends on OF && HAS_IOMEM" from Kconfig.
> >   - Stop using the pointer of struct dw_pcie.
> >   - Use _relaxed variant.
> >   - Drop dw_pcie_wait_for_link.
> >   - Drop dbi resource processing.
> >   - Drop MSI IRQ initialization processing.
>
> Thanks for the changelog.  Please move it after the "---" line for
> future versions.  That way it won't appear in the commit log when this
> is merged.  The notes about v1->v2, v2->v3, etc are useful during
> review, but not after this is merged.
>
> > Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
> > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > ---
> >  drivers/pci/controller/dwc/Kconfig         |   9 +
> >  drivers/pci/controller/dwc/Makefile        |   1 +
> >  drivers/pci/controller/dwc/pcie-visconti.c | 369 +++++++++++++++++++++
> >  3 files changed, 379 insertions(+)
> >  create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c


> > +static u64 visconti_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr)
> > +{
> > +     return pci_addr - PCIE_BUS_OFFSET;
>
> This is called from __dw_pcie_prog_outbound_atu() as:
>
>   cpu_addr = pci->ops->cpu_addr_fixup(pci, cpu_addr);
>
> so I think the parameter here should be *cpu_addr*, not pci_addr.
>
> dra7xx and artpec6 also call it "pci_addr", which is at best
> confusing.
>
> I'm also confused about exactly what .cpu_addr_fixup() does.  Is it
> applying an offset that cannot be deduced from the DT description?  If
> so, *should* this offset be described in DT?

It could be perhaps, but it would be a custom property, not something
we can handle in 'ranges'. I'd rather it be implicit from the
compatible than a custom property.

AIUI, the issue is the cpu address gets masked (high bits discarded).
This can happen when the internal bus address decoding throws away
upper address bits.

For example:

0xa0000000 -> 0x20000000    -> 0x00000000
cpu addr   -> DW local addr -> PCI bus addr

DT has the first and last addresses, but iATU needs the middle and last address.

This could be just a data value rather than an ops function. While a
subtract works here, that's fragile (the DT needs to match the
#define) and I think a mask would be more appropriate.

Rob

Re: [PATCH v3 2/3] PCI: Visconti: Add Toshiba Visconti PCIe host controller driver

[Nobuhiro Iwamatsu]

Hi,


Thanks for your comment.

On Wed, Jun 16, 2021 at 10:32:05AM -0600, Rob Herring wrote:
> On Mon, May 24, 2021 at 12:58 PM Bjorn Helgaas <helgaas@kernel.org> wrote:
> >
> > [+cc Kishon for cpu_addr_fixup() question]
> >
> > Please make the subject "PCI: visconti: Add ..." since the driver
> > names are usually lower-case.  When referring to the hardware itself,
> > use "Visconti", of course.
> >
> > On Mon, May 24, 2021 at 03:30:03PM +0900, Nobuhiro Iwamatsu wrote:
> > > Add support to PCIe RC controller on Toshiba Visconti ARM SoCs. PCIe
> > > controller is based of Synopsys DesignWare PCIe core.
> > >
> > > This patch does not yet use the clock framework to control the clock.
> > > This will be replaced in the future.
> > >
> > > v2 -> v3:
> > >   - Update subject.
> > >   - Wrap description in 75 columns.
> > >   - Change config name to PCIE_VISCONTI_HOST.
> > >   - Update Kconfig text.
> > >   - Drop blank lines.
> > >   - Adjusted to 80 columns.
> > >   - Drop inline from functions for register access.
> > >   - Changed function name from visconti_pcie_check_link_status to
> > >     visconti_pcie_link_up.
> > >   - Update to using dw_pcie_host_init().
> > >   - Reorder these in the order of use in visconti_pcie_establish_link.
> > >   - Rewrite visconti_pcie_host_init() without dw_pcie_setup_rc().
> > >   - Change function name from  visconti_device_turnon() to
> > >     visconti_pcie_power_on().
> > >   - Unify formats such as dev_err().
> > >   - Drop error label in visconti_add_pcie_port().
> > >
> > > v1 -> v2:
> > >   - Fix typo in commit message.
> > >   - Drop "depends on OF && HAS_IOMEM" from Kconfig.
> > >   - Stop using the pointer of struct dw_pcie.
> > >   - Use _relaxed variant.
> > >   - Drop dw_pcie_wait_for_link.
> > >   - Drop dbi resource processing.
> > >   - Drop MSI IRQ initialization processing.
> >
> > Thanks for the changelog.  Please move it after the "---" line for
> > future versions.  That way it won't appear in the commit log when this
> > is merged.  The notes about v1->v2, v2->v3, etc are useful during
> > review, but not after this is merged.
> >
> > > Signed-off-by: Yuji Ishikawa <yuji2.ishikawa@toshiba.co.jp>
> > > Signed-off-by: Nobuhiro Iwamatsu <nobuhiro1.iwamatsu@toshiba.co.jp>
> > > ---
> > >  drivers/pci/controller/dwc/Kconfig         |   9 +
> > >  drivers/pci/controller/dwc/Makefile        |   1 +
> > >  drivers/pci/controller/dwc/pcie-visconti.c | 369 +++++++++++++++++++++
> > >  3 files changed, 379 insertions(+)
> > >  create mode 100644 drivers/pci/controller/dwc/pcie-visconti.c
> 
> 
> > > +static u64 visconti_pcie_cpu_addr_fixup(struct dw_pcie *pci, u64 pci_addr)
> > > +{
> > > +     return pci_addr - PCIE_BUS_OFFSET;
> >
> > This is called from __dw_pcie_prog_outbound_atu() as:
> >
> >   cpu_addr = pci->ops->cpu_addr_fixup(pci, cpu_addr);
> >
> > so I think the parameter here should be *cpu_addr*, not pci_addr.
> >
> > dra7xx and artpec6 also call it "pci_addr", which is at best
> > confusing.
> >
> > I'm also confused about exactly what .cpu_addr_fixup() does.  Is it
> > applying an offset that cannot be deduced from the DT description?  If
> > so, *should* this offset be described in DT?
> 
> It could be perhaps, but it would be a custom property, not something
> we can handle in 'ranges'. I'd rather it be implicit from the
> compatible than a custom property.
> 
> AIUI, the issue is the cpu address gets masked (high bits discarded).
> This can happen when the internal bus address decoding throws away
> upper address bits.
> 
> For example:
> 
> 0xa0000000 -> 0x20000000    -> 0x00000000
> cpu addr   -> DW local addr -> PCI bus addr
> 
> DT has the first and last addresses, but iATU needs the middle and last address.
> 
> This could be just a data value rather than an ops function. While a
> subtract works here, that's fragile (the DT needs to match the
> #define) and I think a mask would be more appropriate.a

In this SoC specification, the CPU bus outputs the offset value from
0x40000000 to the PCIE bus, so 0x40000000 is subtracted from the CPU
bus address. This 0x40000000 is also based on io_base from DT.
Therefore, how about the following processing?

return cpu_addr - pp->io_base;

If I use a mask, it will be as follows.

return cpu_addr & ~pp->io_base;

Best regards,
  Nobuhiro