[PATCH v2 1/2] PCI: Disable D3cold on Asus B1400 PCI-NVMe bridge

[Daniel Drake <drake@endlessos.org>]

The Asus B1400 with original shipped firmware versions and VMD disabled
cannot resume from suspend: the NVMe device becomes unresponsive and
inaccessible.

This is because the NVMe device and parent PCI bridge get put into D3cold
during suspend, and this PCI bridge cannot be recovered from D3cold mode:

  echo "0000:01:00.0" > /sys/bus/pci/drivers/nvme/unbind
  echo "0000:00:06.0" > /sys/bus/pci/drivers/pcieport/unbind
  setpci -s 00:06.0 CAP_PM+4.b=03 # D3hot
  acpidbg -b "execute \_SB.PC00.PEG0.PXP._OFF"
  acpidbg -b "execute \_SB.PC00.PEG0.PXP._ON"
  setpci -s 00:06.0 CAP_PM+4.b=0 # D0
  echo "0000:00:06.0" > /sys/bus/pci/drivers/pcieport/bind
  echo "0000:01:00.0" > /sys/bus/pci/drivers/nvme/bind
  # NVMe probe fails here with -ENODEV

This appears to be an untested D3cold transition by the vendor; Intel
socwatch shows that Windows leaves the NVMe device and parent bridge in D0
during suspend, even though these firmware versions have StorageD3Enable=1.

Experimenting with the DSDT, the _OFF method calls DL23() which sets a L23E
bit at offset 0xe2 into the PCI configuration space for this root port.
This is the specific write that the _ON routine is unable to recover from.
This register is not documented in the public chipset datasheet.

Disallow D3cold on the PCI bridge to enable successful suspend/resume.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=215742
Signed-off-by: Daniel Drake <drake@endlessos.org>
---
 arch/x86/pci/fixup.c | 45 ++++++++++++++++++++++++++++++++++++++++++++
 1 file changed, 45 insertions(+)

v2:
Match only specific BIOS versions where this quirk is required.
Add subsequent patch to this series to revert the original S3 workaround
now that s2idle is usable again.

diff --git a/arch/x86/pci/fixup.c b/arch/x86/pci/fixup.c
index f347c20247d30..6b0b341178e4f 100644
--- a/arch/x86/pci/fixup.c
+++ b/arch/x86/pci/fixup.c
@@ -907,6 +907,51 @@ static void chromeos_fixup_apl_pci_l1ss_capability(struct pci_dev *dev)
 DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x5ad6, chromeos_save_apl_pci_l1ss_capability);
 DECLARE_PCI_FIXUP_RESUME(PCI_VENDOR_ID_INTEL, 0x5ad6, chromeos_fixup_apl_pci_l1ss_capability);
 
+/*
+ * Disable D3cold on Asus B1400 PCIe bridge at 00:06.0.
+ *
+ * On this platform with VMD off, the NVMe's parent PCI bridge cannot
+ * successfully power back on from D3cold, resulting in unresponsive NVMe on
+ * resume. This appears to be an untested transition by the vendor: Windows
+ * leaves the NVMe and parent bridge in D0 during suspend.
+ * This is only needed on BIOS versions before 308; the newer versions flip
+ * StorageD3Enable from 1 to 0.
+ */
+static const struct dmi_system_id asus_nvme_broken_d3cold_table[] = {
+	{
+		.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+				DMI_MATCH(DMI_BIOS_VERSION, "B1400CEAE.304"),
+		},
+	},
+	{
+		.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+				DMI_MATCH(DMI_BIOS_VERSION, "B1400CEAE.305"),
+		},
+	},
+	{
+		.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+				DMI_MATCH(DMI_BIOS_VERSION, "B1400CEAE.306"),
+		},
+	},
+	{
+		.matches = {
+				DMI_MATCH(DMI_SYS_VENDOR, "ASUSTeK COMPUTER INC."),
+				DMI_MATCH(DMI_BIOS_VERSION, "B1400CEAE.307"),
+		},
+	},
+	{}
+};
+
+static void asus_disable_nvme_d3cold(struct pci_dev *pdev)
+{
+	if (dmi_check_system(asus_nvme_broken_d3cold_table) > 0)
+		pci_d3cold_disable(pdev);
+}
+DECLARE_PCI_FIXUP_FINAL(PCI_VENDOR_ID_INTEL, 0x9a09, asus_disable_nvme_d3cold);
+
 #ifdef CONFIG_SUSPEND
 /*
  * Root Ports on some AMD SoCs advertise PME_Support for D3hot and D3cold, but
-- 
2.43.0