Re: [PATCH 1/2] dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe controller

[Hanjie Lin <hanjie.lin@amlogic.com>]

On 2018/8/15 6:53, Rob Herring wrote:
> On Tue, Aug 14, 2018 at 02:18:41AM -0400, Hanjie Lin wrote:
>> From: Yue Wang <yue.wang@amlogic.com>
>>
>> The Amlogic Meson PCIe host controller is based on the Synopsys DesignWare
>> PCI core. This patch adds documentation for the DT bindings in Meson PCIe
>> controller.
>>
>> Signed-off-by: Yue Wang <hanjie.lin@amlogic.com>
>> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
>> ---
>>  .../devicetree/bindings/pci/amlogic,meson-pcie.txt | 57 ++++++++++++++++++++++
>>  1 file changed, 57 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
>>
>> diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
>> new file mode 100644
>> index 0000000..48233e4
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
>> @@ -0,0 +1,57 @@
>> +Amlogic Meson AXG DWC PCIE SoC controller
>> +
>> +Amlogic Meson PCIe host controller is based on the Synopsys DesignWare PCI core.
>> +It shares common functions with the PCIe DesignWare core driver and
>> +inherits common properties defined in
>> +Documentation/devicetree/bindings/pci/designware-pci.txt.
>> +
>> +Additional properties are described here:
>> +
>> +Required properties:
>> +- compatible:
>> +	should contain "amlogic,axg-pcie" to identify the core.
>> +- reg:
>> +	Should contain the configuration address space.
>> +- reg-names: Must be
>> +	- "elbi"	External local bus interface registers
>> +	- "cfg"		Meson specific registers
>> +	- "config"	PCIe configuration space
>> +- clocks: Must contain an entry for each entry in clock-names.
>> +- clock-names: Must include the following entries:
>> +	- "pcie"
>> +	- "pcie_bus"
>> +	- "pcie_general"
>> +	- "pcie_mipi_en"
>> +
>> +Example configuration:
>> +
>> +	pcie: pcie@dffff000 {
> 
> Unit-address is wrong.

Yes, I will fix it.

> 
>> +			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
>> +			reg = <0x0 0xf9800000 0x0 0x400000
>> +					0x0 0xff646000 0x0 0x2000
>> +					0x0 0xf9f00000 0x0 0x100000>;
>> +			reg-names = "elbi", "cfg", "config";
>> +			reset-gpio = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
> 
> Not documented and should be reset-gpios.

Yes, is this more clear?
reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.

> 
>> +			interrupts = <0 177 IRQ_TYPE_EDGE_RISING>;
>> +			#interrupt-cells = <1>;
>> +			interrupt-map-mask = <0 0 0 0>;
>> +			interrupt-map = <0 0 0 0 &gic GIC_SPI 179 IRQ_TYPE_EDGE_RISING>;
>> +			bus-range = <0x0 0xff>;
>> +			#address-cells = <3>;
>> +			#size-cells = <2>;
>> +			device_type = "pci";
>> +			phys = <&pcie_phy>;
>> +			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
>> +			num-lanes = <1>;
>> +			pcie-num = <1>;
> 
> Not documented. What's this?

Yes, pcie-num is an useless parameter. I will delete it.

Thanks for your comments.

> 
>> +
>> +			clocks = <&clkc CLKID_USB
>> +					&clkc CLKID_MIPI_ENABLE
>> +					&clkc CLKID_PCIE_A
>> +					&clkc CLKID_PCIE_CML_EN0>;
>> +			clock-names = "pcie_general",
>> +					"pcie_refpll",
>> +					"pcie_mipi_en",
>> +					"pcie",
>> +					"port";
>> +	};
>> -- 
>> 2.7.4
>>
> 
> .
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel