[PATCH v4 0/2] add one regulator used to power up pcie phy

[PATCH v4 0/2] add one regulator used to power up pcie phy

[Richard Zhu]

Changes:
v3 -> v4
Split the DTS changes to a standalone patch from this patch-set.
And would post to Shawn to take it, after the other two are accepted
by PCIe tree.
Refine the DT binding descriptions refer to Lucas' suggestion.
Use "Regarding" to replace the "Regarding to" in the comments
refer to Krzysztof's suggestion.

v2 -> v3:
Refine the DT binding descriptions, and the condition adjustment in the codes.

v1 -> v2:
Don't use the boolean property to specify the different power supply of PCIe PHY.
Use one regulator as a supply to the PCIe controller node, and the regulator APIs
to get the voltage of it.

Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt |  3 +++
drivers/pci/controller/dwc/pci-imx6.c                    | 20 ++++++++++++++++++++
2 files changed, 23 insertions(+)

[PATCH v4 1/2] dt-bindings: imx6q-pcie: add one regulator used to
[PATCH v4 2/2] PCI: imx: clear vreg bypass when pcie vph voltage is

[PATCH v4 1/2] dt-bindings: imx6q-pcie: add one regulator used to power up pcie phy

[Richard Zhu]

Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
the VREG_BYPASS bits of GPR registers should be cleared from default
value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
turned on.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
---
 Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
index de4b2baf91e8..d8971ab99274 100644
--- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
+++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
@@ -38,6 +38,9 @@ Optional properties:
   The regulator will be enabled when initializing the PCIe host and
   disabled either as part of the init process or when shutting down the
   host.
+- vph-supply: Should specify the regulator in charge of VPH one of the three
+  PCIe PHY powers. This regulator can be supplied by both 1.8v and 3.3v voltage
+  supplies.
 
 Additional required properties for imx6sx-pcie:
 - clock names: Must include the following additional entries:
-- 
2.17.1

[PATCH v4 2/2] PCI: imx: clear vreg bypass when pcie vph voltage is 3v3

[Richard Zhu]

Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
the VREG_BYPASS bits of GPR registers should be cleared from default
value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
turned on.

Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Lucas Stach <l.stach@pengutronix.de>
---
 drivers/pci/controller/dwc/pci-imx6.c | 20 ++++++++++++++++++++
 1 file changed, 20 insertions(+)

diff --git a/drivers/pci/controller/dwc/pci-imx6.c b/drivers/pci/controller/dwc/pci-imx6.c
index 853ea8e82952..94b43b4ecca1 100644
--- a/drivers/pci/controller/dwc/pci-imx6.c
+++ b/drivers/pci/controller/dwc/pci-imx6.c
@@ -37,6 +37,7 @@
 #define IMX8MQ_GPR_PCIE_REF_USE_PAD		BIT(9)
 #define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE_EN	BIT(10)
 #define IMX8MQ_GPR_PCIE_CLK_REQ_OVERRIDE	BIT(11)
+#define IMX8MQ_GPR_PCIE_VREG_BYPASS		BIT(12)
 #define IMX8MQ_GPR12_PCIE2_CTRL_DEVICE_TYPE	GENMASK(11, 8)
 #define IMX8MQ_PCIE2_BASE_ADDR			0x33c00000
 
@@ -80,6 +81,7 @@ struct imx6_pcie {
 	u32			tx_swing_full;
 	u32			tx_swing_low;
 	struct regulator	*vpcie;
+	struct regulator	*vph;
 	void __iomem		*phy_base;
 
 	/* power domain for pcie */
@@ -621,6 +623,17 @@ static void imx6_pcie_init_phy(struct imx6_pcie *imx6_pcie)
 				   imx6_pcie_grp_offset(imx6_pcie),
 				   IMX8MQ_GPR_PCIE_REF_USE_PAD,
 				   IMX8MQ_GPR_PCIE_REF_USE_PAD);
+		/*
+		 * Regarding the datasheet, the PCIE_VPH is suggested
+		 * to be 1.8V. If the PCIE_VPH is supplied by 3.3V, the
+		 * VREG_BYPASS should be cleared to zero.
+		 */
+		if (imx6_pcie->vph &&
+		    regulator_get_voltage(imx6_pcie->vph) > 3000000)
+			regmap_update_bits(imx6_pcie->iomuxc_gpr,
+					   imx6_pcie_grp_offset(imx6_pcie),
+					   IMX8MQ_GPR_PCIE_VREG_BYPASS,
+					   0);
 		break;
 	case IMX7D:
 		regmap_update_bits(imx6_pcie->iomuxc_gpr, IOMUXC_GPR12,
@@ -1130,6 +1143,13 @@ static int imx6_pcie_probe(struct platform_device *pdev)
 		imx6_pcie->vpcie = NULL;
 	}
 
+	imx6_pcie->vph = devm_regulator_get_optional(&pdev->dev, "vph");
+	if (IS_ERR(imx6_pcie->vph)) {
+		if (PTR_ERR(imx6_pcie->vph) != -ENODEV)
+			return PTR_ERR(imx6_pcie->vph);
+		imx6_pcie->vph = NULL;
+	}
+
 	platform_set_drvdata(pdev, imx6_pcie);
 
 	ret = imx6_pcie_attach_pd(dev);
-- 
2.17.1

Re: [PATCH v4 1/2] dt-bindings: imx6q-pcie: add one regulator used to power up pcie phy

[Lucas Stach]

Am Montag, dem 29.03.2021 um 16:03 +0800 schrieb Richard Zhu:
> Both 1.8v and 3.3v power supplies can be used by i.MX8MQ PCIe PHY.
> In default, the PCIE_VPH voltage is suggested to be 1.8v refer to data
> sheet. When PCIE_VPH is supplied by 3.3v in the HW schematic design,
> the VREG_BYPASS bits of GPR registers should be cleared from default
> value 1b'1 to 1b'0. Thus, the internal 3v3 to 1v8 translator would be
> turned on.
> 
> Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>

Reviewed-by: Lucas Stach <l.stach@pengutronix.de>

> ---
>  Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt | 3 +++
>  1 file changed, 3 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> index de4b2baf91e8..d8971ab99274 100644
> --- a/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/fsl,imx6q-pcie.txt
> @@ -38,6 +38,9 @@ Optional properties:
>    The regulator will be enabled when initializing the PCIe host and
>    disabled either as part of the init process or when shutting down the
>    host.
> +- vph-supply: Should specify the regulator in charge of VPH one of the three
> +  PCIe PHY powers. This regulator can be supplied by both 1.8v and 3.3v voltage
> +  supplies.
>  
> 
> 
> 
>  Additional required properties for imx6sx-pcie:
>  - clock names: Must include the following additional entries: