Re: [PATCH 1/2] dt-bindings: PCI: meson: add DT bindings for Amlogic Meson PCIe Phy controller

[Hanjie Lin <hanjie.lin@amlogic.com>]

On 2018/8/15 6:50, Rob Herring wrote:
> On Tue, Aug 14, 2018 at 02:12:13AM -0400, Hanjie Lin wrote:
>> From: Yue Wang <yue.wang@amlogic.com>
> 
> Subject should be "dt-bindings: phy: ..."
> 
>> The Meson-PCIE-PHY controller supports the 5-Gbps data rate
>> of the PCI Express Gen 2 specification and is backwardcompatible
> 
> space    

yes, I will fix
                                               ^
> 
>> with the 2.5-Gbps Gen 1.1 specification with only
>> inferred idle detection supported on AMLOGIC SoCs.
> 
> AMLOGIC or Amlogic? 
> 

yes, we will stick to 'Amlogic'

>>
>> Signed-off-by: Hanjie Lin <hanjie.lin@amlogic.com>
>> Signed-off-by: Yue Wang <yue.wang@amlogic.com>
>> ---
>>  .../bindings/phy/amlogic,meson-pcie-phy.txt        | 31 ++++++++++++++++++++++
>>  1 file changed, 31 insertions(+)
>>  create mode 100644 Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>>
>> diff --git a/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>> new file mode 100644
>> index 0000000..db99085
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/phy/amlogic,meson-pcie-phy.txt
>> @@ -0,0 +1,31 @@
>> +* Amlogic Meson AXG PCIE PHY binding
>> +
>> +Required properties:
>> +- compatible:	Should be
>> +	- "amlogic,axg-pcie-phy"
>> +- #phys-cells:	must be 0 (see phy-bindings.txt in this directory)
> 
> You don't need to distinguish port A and B?

No, we don't. Theoretically there is only one phy in the chip,
and we have distinguished ports by reset lines.

Thanks for all corrections and suggestions.

> 
>> +- reg:		The base address and length of the registers
>> +- resets:	phandle to the reset lines
>> +- reset-names:	must contain "phy" and "peripheral"
>> +	- "port_a" Port A reset
>> +	- "port_b" Port B reset
>> +	- "phy"	PHY reset
>> +	- "apb"	APB reset
>> +Optional properties:
>> +- phy-supply:	see phy-bindings.txt in this directory
>> +
>> +Example:
>> +	pcie_phy: pcie-phy@ff644000 {
>> +		#phy-cells = <0>;
>> +		compatible = "amlogic,axg-pcie-phy";
>> +		reg = <0x0 0xff644000 0x0 0x2000>;
>> +		resets = <&reset RESET_PCIE_A>,
>> +				<&reset RESET_PCIE_B>,
>> +				<&reset RESET_PCIE_PHY>,
>> +				<&reset RESET_PCIE_APB>;
>> +		reset-names =
>> +				"port_a",
>> +				"port_b",
>> +				"phy",
>> +				"apb";
>> +	};
>> -- 
>> 2.7.4
>>
> 
> .
> 

_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel