From: Lina Iyer <lina.iyer@linaro.org>
To: daniel.lezcano@linaro.org, khilman@linaro.org,
sboyd@codeaurora.org, galak@codeaurora.org,
linux-arm-msm@vger.kernel.org, linux-pm@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Cc: lorenzo.pieralisi@arm.com, msivasub@codeaurora.org,
devicetree@vger.kernel.org, Lina Iyer <lina.iyer@linaro.org>
Subject: [PATCH v9 5/9] arm: dts: qcom: Update power-controller device node for 8064 Krait CPUs
Date: Fri, 24 Oct 2014 17:40:20 -0600 [thread overview]
Message-ID: <1414194024-55547-6-git-send-email-lina.iyer@linaro.org> (raw)
In-Reply-To: <1414194024-55547-1-git-send-email-lina.iyer@linaro.org>
Update the SAW2 DT bindings to add qcom,apq8064-saw2-v1.1-cpu compatible
binding string to configure SPM registers and allow the SPM to put the
core in deeper idle states when the core is idle.
Signed-off-by: Lina Iyer <lina.iyer@linaro.org>
---
arch/arm/boot/dts/qcom-apq8064.dtsi | 16 ++++++++--------
1 file changed, 8 insertions(+), 8 deletions(-)
diff --git a/arch/arm/boot/dts/qcom-apq8064.dtsi b/arch/arm/boot/dts/qcom-apq8064.dtsi
index b3154c0..9fd24bc 100644
--- a/arch/arm/boot/dts/qcom-apq8064.dtsi
+++ b/arch/arm/boot/dts/qcom-apq8064.dtsi
@@ -139,26 +139,26 @@
reg = <0x020b8000 0x1000>, <0x02008000 0x1000>;
};
- saw0: regulator@2089000 {
- compatible = "qcom,saw2";
+ saw0: power-controller@2089000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02089000 0x1000>, <0x02009000 0x1000>;
regulator;
};
- saw1: regulator@2099000 {
- compatible = "qcom,saw2";
+ saw1: power-controller@2099000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x02099000 0x1000>, <0x02009000 0x1000>;
regulator;
};
- saw2: regulator@20a9000 {
- compatible = "qcom,saw2";
+ saw2: power-controller@20a9000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020a9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
- saw3: regulator@20b9000 {
- compatible = "qcom,saw2";
+ saw3: power-controller@20b9000 {
+ compatible = "qcom,apq8064-saw2-v1.1-cpu", "qcom,saw2";
reg = <0x020b9000 0x1000>, <0x02009000 0x1000>;
regulator;
};
--
2.1.0
next prev parent reply other threads:[~2014-10-24 23:40 UTC|newest]
Thread overview: 32+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-10-24 23:40 [PATCH v9 0/9] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Lina Iyer
2014-10-24 23:40 ` [PATCH v9 1/9] qcom: scm: scm_set_warm_boot_addr() to set the warmboot address Lina Iyer
2014-11-14 8:30 ` Daniel Lezcano
2014-11-14 16:33 ` Lina Iyer
2014-10-24 23:40 ` [PATCH v9 2/9] qcom: spm: Add Subsystem Power Manager driver Lina Iyer
2014-11-14 15:56 ` Daniel Lezcano
2014-11-19 17:43 ` Lina Iyer
2014-11-26 11:19 ` Daniel Lezcano
2014-11-26 15:20 ` Lina Iyer
2014-11-26 15:22 ` Lina Iyer
2014-11-14 22:46 ` Stephen Boyd
2014-11-18 16:56 ` Lina Iyer
2014-11-18 20:28 ` Stephen Boyd
2014-11-17 21:32 ` Daniel Lezcano
2014-11-18 18:00 ` Lina Iyer
2014-11-18 19:39 ` Bjorn Andersson
2014-11-26 18:04 ` Kevin Hilman
2014-11-26 21:25 ` Daniel Lezcano
2014-10-24 23:40 ` [PATCH v9 3/9] arm: dts: qcom: Add power-controller device node for 8974 Krait CPUs Lina Iyer
2014-10-24 23:40 ` [PATCH v9 4/9] arm: dts: qcom: Add power-controller device node for 8084 " Lina Iyer
2014-10-24 23:40 ` Lina Iyer [this message]
2014-10-24 23:40 ` [PATCH v9 6/9] qcom: cpuidle: Add cpuidle driver for QCOM cpus Lina Iyer
2014-11-16 21:20 ` Daniel Lezcano
2014-11-17 18:30 ` Lina Iyer
2014-11-17 17:39 ` Lorenzo Pieralisi
2014-11-17 22:15 ` Lina Iyer
2014-10-24 23:40 ` [PATCH v9 7/9] arm: dts: qcom: Add idle states device nodes for 8974 Lina Iyer
2014-10-24 23:40 ` [PATCH v9 8/9] arm: dts: qcom: Add idle states device nodes for 8084 Lina Iyer
2014-10-24 23:40 ` [PATCH v9 9/9] arm: dts: qcom: Add idle state device nodes for 8064 Lina Iyer
2014-10-27 9:15 ` [PATCH v9 0/9] cpuidle driver for QCOM SoCs: 8064, 8074, 8084 Ivan T. Ivanov
2014-10-27 14:45 ` Lina Iyer
2014-11-13 20:25 ` Lina Iyer
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=1414194024-55547-6-git-send-email-lina.iyer@linaro.org \
--to=lina.iyer@linaro.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=galak@codeaurora.org \
--cc=khilman@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=lorenzo.pieralisi@arm.com \
--cc=msivasub@codeaurora.org \
--cc=sboyd@codeaurora.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).