* [PATCH v2 0/2] Mediatek thermal driver update
@ 2020-04-30 9:14 Henry Yen
2020-04-30 9:14 ` [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms Henry Yen
` (2 more replies)
0 siblings, 3 replies; 11+ messages in thread
From: Henry Yen @ 2020-04-30 9:14 UTC (permalink / raw)
To: Zhang Rui, Daniel Lezcano, Amit Kucheria, Matthias Brugger
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Henry Yen, Michael Kao
Mediatek owns two thermal systems, which are almost the same except for
the way of reading calibration data and converting temperature.
MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal system,
and MT7622 belongs to version 2. The current code has already supported
version 1 system. Then this patchset will add the support for another
platform (e.g., MT7622 SoC).
Changelog:
v2:
* reorganize the order of the two patches
* remove unnecessary .extract and .convert callbacks
* add fixes tag
v1:
* initial post
Henry Yen (2):
thermal: mediatek: prepare to add support for other platforms
thermal: mediatek: add tsensor support for V2 thermal system
drivers/thermal/mtk_thermal.c | 234 ++++++++++++++++++++++++++--------
1 file changed, 181 insertions(+), 53 deletions(-)
--
2.17.1
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms
2020-04-30 9:14 [PATCH v2 0/2] Mediatek thermal driver update Henry Yen
@ 2020-04-30 9:14 ` Henry Yen
2020-07-10 9:58 ` mtk17045
2020-07-10 15:19 ` Matthias Brugger
2020-04-30 9:14 ` [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system Henry Yen
2020-07-10 9:54 ` [RESEND] Mediatek thermal driver update mtk17045
2 siblings, 2 replies; 11+ messages in thread
From: Henry Yen @ 2020-04-30 9:14 UTC (permalink / raw)
To: Zhang Rui, Daniel Lezcano, Amit Kucheria, Matthias Brugger
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Henry Yen, Michael Kao
It is known that Mediatek owns two thermal systems, which only differ
in the way of reading calibration data and converting temperature.
MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal
system, and MT7622 belongs to version 2.
In order to handle both systems, the suffix _V1 is appended to the
current code, and then the second patch will add _V2 functions with
the same purpose but different implementation.
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
---
drivers/thermal/mtk_thermal.c | 114 ++++++++++++++++++----------------
1 file changed, 62 insertions(+), 52 deletions(-)
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index 76e30603d4d5..10107d9d56a8 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -120,18 +120,18 @@
* MT2701 has 3 sensors and needs 3 VTS calibration data.
* MT2712 has 4 sensors and needs 4 VTS calibration data.
*/
-#define CALIB_BUF0_VALID BIT(0)
-#define CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff)
-#define CALIB_BUF0_VTS_TS1(x) (((x) >> 17) & 0x1ff)
-#define CALIB_BUF0_VTS_TS2(x) (((x) >> 8) & 0x1ff)
-#define CALIB_BUF1_VTS_TS3(x) (((x) >> 0) & 0x1ff)
-#define CALIB_BUF2_VTS_TS4(x) (((x) >> 23) & 0x1ff)
-#define CALIB_BUF2_VTS_TS5(x) (((x) >> 5) & 0x1ff)
-#define CALIB_BUF2_VTS_TSABB(x) (((x) >> 14) & 0x1ff)
-#define CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f)
-#define CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f)
-#define CALIB_BUF0_O_SLOPE_SIGN(x) (((x) >> 7) & 0x1)
-#define CALIB_BUF1_ID(x) (((x) >> 9) & 0x1)
+#define CALIB_BUF0_VALID_V1 BIT(0)
+#define CALIB_BUF1_ADC_GE_V1(x) (((x) >> 22) & 0x3ff)
+#define CALIB_BUF0_VTS_TS1_V1(x) (((x) >> 17) & 0x1ff)
+#define CALIB_BUF0_VTS_TS2_V1(x) (((x) >> 8) & 0x1ff)
+#define CALIB_BUF1_VTS_TS3_V1(x) (((x) >> 0) & 0x1ff)
+#define CALIB_BUF2_VTS_TS4_V1(x) (((x) >> 23) & 0x1ff)
+#define CALIB_BUF2_VTS_TS5_V1(x) (((x) >> 5) & 0x1ff)
+#define CALIB_BUF2_VTS_TSABB_V1(x) (((x) >> 14) & 0x1ff)
+#define CALIB_BUF0_DEGC_CALI_V1(x) (((x) >> 1) & 0x3f)
+#define CALIB_BUF0_O_SLOPE_V1(x) (((x) >> 26) & 0x3f)
+#define CALIB_BUF0_O_SLOPE_SIGN_V1(x) (((x) >> 7) & 0x1)
+#define CALIB_BUF1_ID_V1(x) (((x) >> 9) & 0x1)
enum {
VTS1,
@@ -525,7 +525,7 @@ static const struct mtk_thermal_data mt8183_thermal_data = {
* This converts the raw ADC value to mcelsius using the SoC specific
* calibration constants
*/
-static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
+static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
{
s32 tmp;
@@ -594,9 +594,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
raw = readl(mt->thermal_base +
conf->msr[conf->bank_data[bank->id].sensors[i]]);
- temp = raw_to_mcelsius(mt,
- conf->bank_data[bank->id].sensors[i],
- raw);
+ temp = raw_to_mcelsius_v1(mt,
+ conf->bank_data[bank->id].sensors[i],
+ raw);
/*
* The first read of a sensor often contains very high bogus
@@ -758,6 +758,51 @@ static u64 of_get_phys_base(struct device_node *np)
return of_translate_address(np, regaddr_p);
}
+static int mtk_thermal_extract_efuse_v1(struct mtk_thermal *mt, u32 *buf)
+{
+ int i;
+
+ if (!(buf[0] & CALIB_BUF0_VALID_V1))
+ return -EINVAL;
+
+ mt->adc_ge = CALIB_BUF1_ADC_GE_V1(buf[1]);
+
+ for (i = 0; i < mt->conf->num_sensors; i++) {
+ switch (mt->conf->vts_index[i]) {
+ case VTS1:
+ mt->vts[VTS1] = CALIB_BUF0_VTS_TS1_V1(buf[0]);
+ break;
+ case VTS2:
+ mt->vts[VTS2] = CALIB_BUF0_VTS_TS2_V1(buf[0]);
+ break;
+ case VTS3:
+ mt->vts[VTS3] = CALIB_BUF1_VTS_TS3_V1(buf[1]);
+ break;
+ case VTS4:
+ mt->vts[VTS4] = CALIB_BUF2_VTS_TS4_V1(buf[2]);
+ break;
+ case VTS5:
+ mt->vts[VTS5] = CALIB_BUF2_VTS_TS5_V1(buf[2]);
+ break;
+ case VTSABB:
+ mt->vts[VTSABB] =
+ CALIB_BUF2_VTS_TSABB_V1(buf[2]);
+ break;
+ default:
+ break;
+ }
+ }
+
+ mt->degc_cali = CALIB_BUF0_DEGC_CALI_V1(buf[0]);
+ if (CALIB_BUF1_ID_V1(buf[1]) &
+ CALIB_BUF0_O_SLOPE_SIGN_V1(buf[0]))
+ mt->o_slope = -CALIB_BUF0_O_SLOPE_V1(buf[0]);
+ else
+ mt->o_slope = CALIB_BUF0_O_SLOPE_V1(buf[0]);
+
+ return 0;
+}
+
static int mtk_thermal_get_calibration_data(struct device *dev,
struct mtk_thermal *mt)
{
@@ -793,43 +838,8 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
goto out;
}
- if (buf[0] & CALIB_BUF0_VALID) {
- mt->adc_ge = CALIB_BUF1_ADC_GE(buf[1]);
-
- for (i = 0; i < mt->conf->num_sensors; i++) {
- switch (mt->conf->vts_index[i]) {
- case VTS1:
- mt->vts[VTS1] = CALIB_BUF0_VTS_TS1(buf[0]);
- break;
- case VTS2:
- mt->vts[VTS2] = CALIB_BUF0_VTS_TS2(buf[0]);
- break;
- case VTS3:
- mt->vts[VTS3] = CALIB_BUF1_VTS_TS3(buf[1]);
- break;
- case VTS4:
- mt->vts[VTS4] = CALIB_BUF2_VTS_TS4(buf[2]);
- break;
- case VTS5:
- mt->vts[VTS5] = CALIB_BUF2_VTS_TS5(buf[2]);
- break;
- case VTSABB:
- mt->vts[VTSABB] = CALIB_BUF2_VTS_TSABB(buf[2]);
- break;
- default:
- break;
- }
- }
-
- mt->degc_cali = CALIB_BUF0_DEGC_CALI(buf[0]);
- if (CALIB_BUF1_ID(buf[1]) &
- CALIB_BUF0_O_SLOPE_SIGN(buf[0]))
- mt->o_slope = -CALIB_BUF0_O_SLOPE(buf[0]);
- else
- mt->o_slope = CALIB_BUF0_O_SLOPE(buf[0]);
- } else {
+ if (mtk_thermal_extract_efuse_v1(mt, buf))
dev_info(dev, "Device not calibrated, using default calibration values\n");
- }
out:
kfree(buf);
--
2.17.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system
2020-04-30 9:14 [PATCH v2 0/2] Mediatek thermal driver update Henry Yen
2020-04-30 9:14 ` [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms Henry Yen
@ 2020-04-30 9:14 ` Henry Yen
2020-07-10 10:02 ` mtk17045
2020-07-10 15:23 ` Matthias Brugger
2020-07-10 9:54 ` [RESEND] Mediatek thermal driver update mtk17045
2 siblings, 2 replies; 11+ messages in thread
From: Henry Yen @ 2020-04-30 9:14 UTC (permalink / raw)
To: Zhang Rui, Daniel Lezcano, Amit Kucheria, Matthias Brugger
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Henry Yen, Michael Kao
This patch adds full support for ver 2 thermal system (e.g., MT7622 SoC).
The new changes include reading calibration data, converting temperature
and hardware initialization which are specific for version 2 system.
Each platform decides which function to call according to its version.
Fixes: 3966be3c08c3 ("thermal: mediatek: add support for MT7622 SoC")
Signed-off-by: Henry Yen <henry.yen@mediatek.com>
---
drivers/thermal/mtk_thermal.c | 132 ++++++++++++++++++++++++++++++++--
1 file changed, 125 insertions(+), 7 deletions(-)
diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
index 10107d9d56a8..88620f7e9890 100644
--- a/drivers/thermal/mtk_thermal.c
+++ b/drivers/thermal/mtk_thermal.c
@@ -38,6 +38,7 @@
#define TEMP_MONIDET0 0x014
#define TEMP_MONIDET1 0x018
#define TEMP_MSRCTL0 0x038
+#define TEMP_MSRCTL1 0x03c
#define TEMP_AHBPOLL 0x040
#define TEMP_AHBTO 0x044
#define TEMP_ADCPNP0 0x048
@@ -133,6 +134,20 @@
#define CALIB_BUF0_O_SLOPE_SIGN_V1(x) (((x) >> 7) & 0x1)
#define CALIB_BUF1_ID_V1(x) (((x) >> 9) & 0x1)
+/*
+ * Layout of the fuses providing the calibration data
+ * These macros could be used for MT7622.
+ */
+#define CALIB_BUF0_ADC_OE_V2(x) (((x) >> 22) & 0x3ff)
+#define CALIB_BUF0_ADC_GE_V2(x) (((x) >> 12) & 0x3ff)
+#define CALIB_BUF0_DEGC_CALI_V2(x) (((x) >> 6) & 0x3f)
+#define CALIB_BUF0_O_SLOPE_V2(x) (((x) >> 0) & 0x3f)
+#define CALIB_BUF1_VTS_TS1_V2(x) (((x) >> 23) & 0x1ff)
+#define CALIB_BUF1_VTS_TS2_V2(x) (((x) >> 14) & 0x1ff)
+#define CALIB_BUF1_VTS_TSABB_V2(x) (((x) >> 5) & 0x1ff)
+#define CALIB_BUF1_VALID_V2(x) (((x) >> 4) & 0x1)
+#define CALIB_BUF1_O_SLOPE_SIGN_V2(x) (((x) >> 3) & 0x1)
+
enum {
VTS1,
VTS2,
@@ -143,6 +158,11 @@ enum {
MAX_NUM_VTS,
};
+enum mtk_thermal_version {
+ MTK_THERMAL_V1 = 1,
+ MTK_THERMAL_V2,
+};
+
/* MT2701 thermal sensors */
#define MT2701_TS1 0
#define MT2701_TS2 1
@@ -245,6 +265,7 @@ struct mtk_thermal_data {
const int *controller_offset;
bool need_switch_bank;
struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
+ enum mtk_thermal_version version;
};
struct mtk_thermal {
@@ -258,8 +279,10 @@ struct mtk_thermal {
/* Calibration values */
s32 adc_ge;
+ s32 adc_oe;
s32 degc_cali;
s32 o_slope;
+ s32 o_slope_sign;
s32 vts[MAX_NUM_VTS];
const struct mtk_thermal_data *conf;
@@ -398,6 +421,7 @@ static const struct mtk_thermal_data mt8173_thermal_data = {
.msr = mt8173_msr,
.adcpnp = mt8173_adcpnp,
.sensor_mux_values = mt8173_mux_values,
+ .version = MTK_THERMAL_V1,
};
/*
@@ -428,6 +452,7 @@ static const struct mtk_thermal_data mt2701_thermal_data = {
.msr = mt2701_msr,
.adcpnp = mt2701_adcpnp,
.sensor_mux_values = mt2701_mux_values,
+ .version = MTK_THERMAL_V1,
};
/*
@@ -458,6 +483,7 @@ static const struct mtk_thermal_data mt2712_thermal_data = {
.msr = mt2712_msr,
.adcpnp = mt2712_adcpnp,
.sensor_mux_values = mt2712_mux_values,
+ .version = MTK_THERMAL_V1,
};
/*
@@ -482,6 +508,7 @@ static const struct mtk_thermal_data mt7622_thermal_data = {
.msr = mt7622_msr,
.adcpnp = mt7622_adcpnp,
.sensor_mux_values = mt7622_mux_values,
+ .version = MTK_THERMAL_V2,
};
/*
@@ -514,6 +541,7 @@ static const struct mtk_thermal_data mt8183_thermal_data = {
.msr = mt8183_msr,
.adcpnp = mt8183_adcpnp,
.sensor_mux_values = mt8183_mux_values,
+ .version = MTK_THERMAL_V1,
};
/**
@@ -540,6 +568,36 @@ static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
return mt->degc_cali * 500 - tmp;
}
+static int raw_to_mcelsius_v2(struct mtk_thermal *mt, int sensno, s32 raw)
+{
+ s32 format_1 = 0;
+ s32 format_2 = 0;
+ s32 g_oe = 1;
+ s32 g_gain = 1;
+ s32 g_x_roomt = 0;
+ s32 tmp = 0;
+
+ if (raw == 0)
+ return 0;
+
+ raw &= 0xfff;
+ g_gain = 10000 + (((mt->adc_ge - 512) * 10000) >> 12);
+ g_oe = mt->adc_oe - 512;
+ format_1 = mt->vts[VTS2] + 3105 - g_oe;
+ format_2 = (mt->degc_cali * 10) >> 1;
+ g_x_roomt = (((format_1 * 10000) >> 12) * 10000) / g_gain;
+
+ tmp = (((((raw - g_oe) * 10000) >> 12) * 10000) / g_gain) - g_x_roomt;
+ tmp = tmp * 10 * 100 / 11;
+
+ if (mt->o_slope_sign == 0)
+ tmp = tmp / (165 - mt->o_slope);
+ else
+ tmp = tmp / (165 + mt->o_slope);
+
+ return (format_2 - tmp) * 100;
+}
+
/**
* mtk_thermal_get_bank - get bank
* @bank: The bank
@@ -594,9 +652,13 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
raw = readl(mt->thermal_base +
conf->msr[conf->bank_data[bank->id].sensors[i]]);
- temp = raw_to_mcelsius_v1(mt,
- conf->bank_data[bank->id].sensors[i],
- raw);
+ if (mt->conf->version == MTK_THERMAL_V1) {
+ temp = raw_to_mcelsius_v1(
+ mt, conf->bank_data[bank->id].sensors[i], raw);
+ } else {
+ temp = raw_to_mcelsius_v2(
+ mt, conf->bank_data[bank->id].sensors[i], raw);
+ }
/*
* The first read of a sensor often contains very high bogus
@@ -698,9 +760,11 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
controller_base + TEMP_ADCMUXADDR);
- /* AHB address for pnp sensor mux selection */
- writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
- controller_base + TEMP_PNPMUXADDR);
+ if (mt->conf->version == MTK_THERMAL_V1) {
+ /* AHB address for pnp sensor mux selection */
+ writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
+ controller_base + TEMP_PNPMUXADDR);
+ }
/* AHB value for auxadc enable */
writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCEN);
@@ -803,6 +867,23 @@ static int mtk_thermal_extract_efuse_v1(struct mtk_thermal *mt, u32 *buf)
return 0;
}
+static int mtk_thermal_extract_efuse_v2(struct mtk_thermal *mt, u32 *buf)
+{
+ if (!CALIB_BUF1_VALID_V2(buf[1]))
+ return -EINVAL;
+
+ mt->adc_oe = CALIB_BUF0_ADC_OE_V2(buf[0]);
+ mt->adc_ge = CALIB_BUF0_ADC_GE_V2(buf[0]);
+ mt->degc_cali = CALIB_BUF0_DEGC_CALI_V2(buf[0]);
+ mt->o_slope = CALIB_BUF0_O_SLOPE_V2(buf[0]);
+ mt->vts[VTS1] = CALIB_BUF1_VTS_TS1_V2(buf[1]);
+ mt->vts[VTS2] = CALIB_BUF1_VTS_TS2_V2(buf[1]);
+ mt->vts[VTSABB] = CALIB_BUF1_VTS_TSABB_V2(buf[1]);
+ mt->o_slope_sign = CALIB_BUF1_O_SLOPE_SIGN_V2(buf[1]);
+
+ return 0;
+}
+
static int mtk_thermal_get_calibration_data(struct device *dev,
struct mtk_thermal *mt)
{
@@ -838,8 +919,15 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
goto out;
}
- if (mtk_thermal_extract_efuse_v1(mt, buf))
+ if (mt->conf->version == MTK_THERMAL_V1)
+ ret = mtk_thermal_extract_efuse_v1(mt, buf);
+ else
+ ret = mtk_thermal_extract_efuse_v2(mt, buf);
+
+ if (ret) {
dev_info(dev, "Device not calibrated, using default calibration values\n");
+ ret = 0;
+ }
out:
kfree(buf);
@@ -872,6 +960,28 @@ static const struct of_device_id mtk_thermal_of_match[] = {
};
MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);
+static void mtk_thermal_turn_on_buffer(void __iomem *apmixed_base)
+{
+ int tmp;
+
+ tmp = readl(apmixed_base + APMIXED_SYS_TS_CON1);
+ tmp &= ~(0x37);
+ tmp |= 0x1;
+ writel(tmp, apmixed_base + APMIXED_SYS_TS_CON1);
+ udelay(200);
+}
+
+static void mtk_thermal_release_periodic_ts(struct mtk_thermal *mt,
+ void __iomem *auxadc_base)
+{
+ int tmp;
+
+ writel(0x800, auxadc_base + AUXADC_CON1_SET_V);
+ writel(0x1, mt->thermal_base + TEMP_MONCTL0);
+ tmp = readl(mt->thermal_base + TEMP_MSRCTL1);
+ writel((tmp & (~0x10e)), mt->thermal_base + TEMP_MSRCTL1);
+}
+
static int mtk_thermal_probe(struct platform_device *pdev)
{
int ret, i, ctrl_id;
@@ -880,6 +990,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
struct resource *res;
u64 auxadc_phys_base, apmixed_phys_base;
struct thermal_zone_device *tzdev;
+ void __iomem *apmixed_base, *auxadc_base;
mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
if (!mt)
@@ -914,6 +1025,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
return -ENODEV;
}
+ auxadc_base = of_iomap(auxadc, 0);
auxadc_phys_base = of_get_phys_base(auxadc);
of_node_put(auxadc);
@@ -929,6 +1041,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
return -ENODEV;
}
+ apmixed_base = of_iomap(apmixedsys, 0);
apmixed_phys_base = of_get_phys_base(apmixedsys);
of_node_put(apmixedsys);
@@ -954,6 +1067,11 @@ static int mtk_thermal_probe(struct platform_device *pdev)
goto err_disable_clk_auxadc;
}
+ if (mt->conf->version == MTK_THERMAL_V2) {
+ mtk_thermal_turn_on_buffer(apmixed_base);
+ mtk_thermal_release_periodic_ts(mt, auxadc_base);
+ }
+
for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
for (i = 0; i < mt->conf->num_banks; i++)
mtk_thermal_init_bank(mt, i, apmixed_phys_base,
--
2.17.1
^ permalink raw reply related [flat|nested] 11+ messages in thread
* [RESEND] Mediatek thermal driver update
2020-04-30 9:14 [PATCH v2 0/2] Mediatek thermal driver update Henry Yen
2020-04-30 9:14 ` [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms Henry Yen
2020-04-30 9:14 ` [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system Henry Yen
@ 2020-07-10 9:54 ` mtk17045
2 siblings, 0 replies; 11+ messages in thread
From: mtk17045 @ 2020-07-10 9:54 UTC (permalink / raw)
To: Daniel Lezcano, Matthias Brugger, Amit Kucheria, Zhang Rui
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Michael Kao
On Thu, 2020-04-30 at 17:14 +0800, Henry Yen wrote:
> Mediatek owns two thermal systems, which are almost the same except for
> the way of reading calibration data and converting temperature.
> MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal system,
> and MT7622 belongs to version 2. The current code has already supported
> version 1 system. Then this patchset will add the support for another
> platform (e.g., MT7622 SoC).
>
> Changelog:
>
> v2:
> * reorganize the order of the two patches
> * remove unnecessary .extract and .convert callbacks
> * add fixes tag
>
> v1:
> * initial post
>
> Henry Yen (2):
> thermal: mediatek: prepare to add support for other platforms
> thermal: mediatek: add tsensor support for V2 thermal system
>
> drivers/thermal/mtk_thermal.c | 234 ++++++++++++++++++++++++++--------
> 1 file changed, 181 insertions(+), 53 deletions(-)
>
Just gently ping.
Many thanks.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms
2020-04-30 9:14 ` [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms Henry Yen
@ 2020-07-10 9:58 ` mtk17045
2020-07-10 15:19 ` Matthias Brugger
1 sibling, 0 replies; 11+ messages in thread
From: mtk17045 @ 2020-07-10 9:58 UTC (permalink / raw)
To: Daniel Lezcano, Matthias Brugger, Amit Kucheria, . Zhang Rui
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Michael Kao, Henry Yen
On Thu, 2020-04-30 at 17:14 +0800, Henry Yen wrote:
> It is known that Mediatek owns two thermal systems, which only differ
> in the way of reading calibration data and converting temperature.
> MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal
> system, and MT7622 belongs to version 2.
>
> In order to handle both systems, the suffix _V1 is appended to the
> current code, and then the second patch will add _V2 functions with
> the same purpose but different implementation.
>
> Signed-off-by: Henry Yen <henry.yen@mediatek.com>
> ---
> drivers/thermal/mtk_thermal.c | 114 ++++++++++++++++++----------------
> 1 file changed, 62 insertions(+), 52 deletions(-)
>
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 76e30603d4d5..10107d9d56a8 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -120,18 +120,18 @@
> * MT2701 has 3 sensors and needs 3 VTS calibration data.
> * MT2712 has 4 sensors and needs 4 VTS calibration data.
> */
> -#define CALIB_BUF0_VALID BIT(0)
> -#define CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff)
> -#define CALIB_BUF0_VTS_TS1(x) (((x) >> 17) & 0x1ff)
> -#define CALIB_BUF0_VTS_TS2(x) (((x) >> 8) & 0x1ff)
> -#define CALIB_BUF1_VTS_TS3(x) (((x) >> 0) & 0x1ff)
> -#define CALIB_BUF2_VTS_TS4(x) (((x) >> 23) & 0x1ff)
> -#define CALIB_BUF2_VTS_TS5(x) (((x) >> 5) & 0x1ff)
> -#define CALIB_BUF2_VTS_TSABB(x) (((x) >> 14) & 0x1ff)
> -#define CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f)
> -#define CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f)
> -#define CALIB_BUF0_O_SLOPE_SIGN(x) (((x) >> 7) & 0x1)
> -#define CALIB_BUF1_ID(x) (((x) >> 9) & 0x1)
> +#define CALIB_BUF0_VALID_V1 BIT(0)
> +#define CALIB_BUF1_ADC_GE_V1(x) (((x) >> 22) & 0x3ff)
> +#define CALIB_BUF0_VTS_TS1_V1(x) (((x) >> 17) & 0x1ff)
> +#define CALIB_BUF0_VTS_TS2_V1(x) (((x) >> 8) & 0x1ff)
> +#define CALIB_BUF1_VTS_TS3_V1(x) (((x) >> 0) & 0x1ff)
> +#define CALIB_BUF2_VTS_TS4_V1(x) (((x) >> 23) & 0x1ff)
> +#define CALIB_BUF2_VTS_TS5_V1(x) (((x) >> 5) & 0x1ff)
> +#define CALIB_BUF2_VTS_TSABB_V1(x) (((x) >> 14) & 0x1ff)
> +#define CALIB_BUF0_DEGC_CALI_V1(x) (((x) >> 1) & 0x3f)
> +#define CALIB_BUF0_O_SLOPE_V1(x) (((x) >> 26) & 0x3f)
> +#define CALIB_BUF0_O_SLOPE_SIGN_V1(x) (((x) >> 7) & 0x1)
> +#define CALIB_BUF1_ID_V1(x) (((x) >> 9) & 0x1)
>
> enum {
> VTS1,
> @@ -525,7 +525,7 @@ static const struct mtk_thermal_data mt8183_thermal_data = {
> * This converts the raw ADC value to mcelsius using the SoC specific
> * calibration constants
> */
> -static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
> +static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
> {
> s32 tmp;
>
> @@ -594,9 +594,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> raw = readl(mt->thermal_base +
> conf->msr[conf->bank_data[bank->id].sensors[i]]);
>
> - temp = raw_to_mcelsius(mt,
> - conf->bank_data[bank->id].sensors[i],
> - raw);
> + temp = raw_to_mcelsius_v1(mt,
> + conf->bank_data[bank->id].sensors[i],
> + raw);
>
> /*
> * The first read of a sensor often contains very high bogus
> @@ -758,6 +758,51 @@ static u64 of_get_phys_base(struct device_node *np)
> return of_translate_address(np, regaddr_p);
> }
>
> +static int mtk_thermal_extract_efuse_v1(struct mtk_thermal *mt, u32 *buf)
> +{
> + int i;
> +
> + if (!(buf[0] & CALIB_BUF0_VALID_V1))
> + return -EINVAL;
> +
> + mt->adc_ge = CALIB_BUF1_ADC_GE_V1(buf[1]);
> +
> + for (i = 0; i < mt->conf->num_sensors; i++) {
> + switch (mt->conf->vts_index[i]) {
> + case VTS1:
> + mt->vts[VTS1] = CALIB_BUF0_VTS_TS1_V1(buf[0]);
> + break;
> + case VTS2:
> + mt->vts[VTS2] = CALIB_BUF0_VTS_TS2_V1(buf[0]);
> + break;
> + case VTS3:
> + mt->vts[VTS3] = CALIB_BUF1_VTS_TS3_V1(buf[1]);
> + break;
> + case VTS4:
> + mt->vts[VTS4] = CALIB_BUF2_VTS_TS4_V1(buf[2]);
> + break;
> + case VTS5:
> + mt->vts[VTS5] = CALIB_BUF2_VTS_TS5_V1(buf[2]);
> + break;
> + case VTSABB:
> + mt->vts[VTSABB] =
> + CALIB_BUF2_VTS_TSABB_V1(buf[2]);
> + break;
> + default:
> + break;
> + }
> + }
> +
> + mt->degc_cali = CALIB_BUF0_DEGC_CALI_V1(buf[0]);
> + if (CALIB_BUF1_ID_V1(buf[1]) &
> + CALIB_BUF0_O_SLOPE_SIGN_V1(buf[0]))
> + mt->o_slope = -CALIB_BUF0_O_SLOPE_V1(buf[0]);
> + else
> + mt->o_slope = CALIB_BUF0_O_SLOPE_V1(buf[0]);
> +
> + return 0;
> +}
> +
> static int mtk_thermal_get_calibration_data(struct device *dev,
> struct mtk_thermal *mt)
> {
> @@ -793,43 +838,8 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
> goto out;
> }
>
> - if (buf[0] & CALIB_BUF0_VALID) {
> - mt->adc_ge = CALIB_BUF1_ADC_GE(buf[1]);
> -
> - for (i = 0; i < mt->conf->num_sensors; i++) {
> - switch (mt->conf->vts_index[i]) {
> - case VTS1:
> - mt->vts[VTS1] = CALIB_BUF0_VTS_TS1(buf[0]);
> - break;
> - case VTS2:
> - mt->vts[VTS2] = CALIB_BUF0_VTS_TS2(buf[0]);
> - break;
> - case VTS3:
> - mt->vts[VTS3] = CALIB_BUF1_VTS_TS3(buf[1]);
> - break;
> - case VTS4:
> - mt->vts[VTS4] = CALIB_BUF2_VTS_TS4(buf[2]);
> - break;
> - case VTS5:
> - mt->vts[VTS5] = CALIB_BUF2_VTS_TS5(buf[2]);
> - break;
> - case VTSABB:
> - mt->vts[VTSABB] = CALIB_BUF2_VTS_TSABB(buf[2]);
> - break;
> - default:
> - break;
> - }
> - }
> -
> - mt->degc_cali = CALIB_BUF0_DEGC_CALI(buf[0]);
> - if (CALIB_BUF1_ID(buf[1]) &
> - CALIB_BUF0_O_SLOPE_SIGN(buf[0]))
> - mt->o_slope = -CALIB_BUF0_O_SLOPE(buf[0]);
> - else
> - mt->o_slope = CALIB_BUF0_O_SLOPE(buf[0]);
> - } else {
> + if (mtk_thermal_extract_efuse_v1(mt, buf))
> dev_info(dev, "Device not calibrated, using default calibration values\n");
> - }
>
> out:
> kfree(buf);
Just gently ping.
Many thanks.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system
2020-04-30 9:14 ` [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system Henry Yen
@ 2020-07-10 10:02 ` mtk17045
2020-07-10 15:23 ` Matthias Brugger
1 sibling, 0 replies; 11+ messages in thread
From: mtk17045 @ 2020-07-10 10:02 UTC (permalink / raw)
To: Matthias Brugger, Amit Kucheria, Daniel Lezcano, . Zhang Rui
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Michael Kao, Henry Yen
On Thu, 2020-04-30 at 17:14 +0800, Henry Yen wrote:
> This patch adds full support for ver 2 thermal system (e.g., MT7622 SoC).
> The new changes include reading calibration data, converting temperature
> and hardware initialization which are specific for version 2 system.
> Each platform decides which function to call according to its version.
>
> Fixes: 3966be3c08c3 ("thermal: mediatek: add support for MT7622 SoC")
> Signed-off-by: Henry Yen <henry.yen@mediatek.com>
> ---
> drivers/thermal/mtk_thermal.c | 132 ++++++++++++++++++++++++++++++++--
> 1 file changed, 125 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 10107d9d56a8..88620f7e9890 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -38,6 +38,7 @@
> #define TEMP_MONIDET0 0x014
> #define TEMP_MONIDET1 0x018
> #define TEMP_MSRCTL0 0x038
> +#define TEMP_MSRCTL1 0x03c
> #define TEMP_AHBPOLL 0x040
> #define TEMP_AHBTO 0x044
> #define TEMP_ADCPNP0 0x048
> @@ -133,6 +134,20 @@
> #define CALIB_BUF0_O_SLOPE_SIGN_V1(x) (((x) >> 7) & 0x1)
> #define CALIB_BUF1_ID_V1(x) (((x) >> 9) & 0x1)
>
> +/*
> + * Layout of the fuses providing the calibration data
> + * These macros could be used for MT7622.
> + */
> +#define CALIB_BUF0_ADC_OE_V2(x) (((x) >> 22) & 0x3ff)
> +#define CALIB_BUF0_ADC_GE_V2(x) (((x) >> 12) & 0x3ff)
> +#define CALIB_BUF0_DEGC_CALI_V2(x) (((x) >> 6) & 0x3f)
> +#define CALIB_BUF0_O_SLOPE_V2(x) (((x) >> 0) & 0x3f)
> +#define CALIB_BUF1_VTS_TS1_V2(x) (((x) >> 23) & 0x1ff)
> +#define CALIB_BUF1_VTS_TS2_V2(x) (((x) >> 14) & 0x1ff)
> +#define CALIB_BUF1_VTS_TSABB_V2(x) (((x) >> 5) & 0x1ff)
> +#define CALIB_BUF1_VALID_V2(x) (((x) >> 4) & 0x1)
> +#define CALIB_BUF1_O_SLOPE_SIGN_V2(x) (((x) >> 3) & 0x1)
> +
> enum {
> VTS1,
> VTS2,
> @@ -143,6 +158,11 @@ enum {
> MAX_NUM_VTS,
> };
>
> +enum mtk_thermal_version {
> + MTK_THERMAL_V1 = 1,
> + MTK_THERMAL_V2,
> +};
> +
> /* MT2701 thermal sensors */
> #define MT2701_TS1 0
> #define MT2701_TS2 1
> @@ -245,6 +265,7 @@ struct mtk_thermal_data {
> const int *controller_offset;
> bool need_switch_bank;
> struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
> + enum mtk_thermal_version version;
> };
>
> struct mtk_thermal {
> @@ -258,8 +279,10 @@ struct mtk_thermal {
>
> /* Calibration values */
> s32 adc_ge;
> + s32 adc_oe;
> s32 degc_cali;
> s32 o_slope;
> + s32 o_slope_sign;
> s32 vts[MAX_NUM_VTS];
>
> const struct mtk_thermal_data *conf;
> @@ -398,6 +421,7 @@ static const struct mtk_thermal_data mt8173_thermal_data = {
> .msr = mt8173_msr,
> .adcpnp = mt8173_adcpnp,
> .sensor_mux_values = mt8173_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /*
> @@ -428,6 +452,7 @@ static const struct mtk_thermal_data mt2701_thermal_data = {
> .msr = mt2701_msr,
> .adcpnp = mt2701_adcpnp,
> .sensor_mux_values = mt2701_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /*
> @@ -458,6 +483,7 @@ static const struct mtk_thermal_data mt2712_thermal_data = {
> .msr = mt2712_msr,
> .adcpnp = mt2712_adcpnp,
> .sensor_mux_values = mt2712_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /*
> @@ -482,6 +508,7 @@ static const struct mtk_thermal_data mt7622_thermal_data = {
> .msr = mt7622_msr,
> .adcpnp = mt7622_adcpnp,
> .sensor_mux_values = mt7622_mux_values,
> + .version = MTK_THERMAL_V2,
> };
>
> /*
> @@ -514,6 +541,7 @@ static const struct mtk_thermal_data mt8183_thermal_data = {
> .msr = mt8183_msr,
> .adcpnp = mt8183_adcpnp,
> .sensor_mux_values = mt8183_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /**
> @@ -540,6 +568,36 @@ static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
> return mt->degc_cali * 500 - tmp;
> }
>
> +static int raw_to_mcelsius_v2(struct mtk_thermal *mt, int sensno, s32 raw)
> +{
> + s32 format_1 = 0;
> + s32 format_2 = 0;
> + s32 g_oe = 1;
> + s32 g_gain = 1;
> + s32 g_x_roomt = 0;
> + s32 tmp = 0;
> +
> + if (raw == 0)
> + return 0;
> +
> + raw &= 0xfff;
> + g_gain = 10000 + (((mt->adc_ge - 512) * 10000) >> 12);
> + g_oe = mt->adc_oe - 512;
> + format_1 = mt->vts[VTS2] + 3105 - g_oe;
> + format_2 = (mt->degc_cali * 10) >> 1;
> + g_x_roomt = (((format_1 * 10000) >> 12) * 10000) / g_gain;
> +
> + tmp = (((((raw - g_oe) * 10000) >> 12) * 10000) / g_gain) - g_x_roomt;
> + tmp = tmp * 10 * 100 / 11;
> +
> + if (mt->o_slope_sign == 0)
> + tmp = tmp / (165 - mt->o_slope);
> + else
> + tmp = tmp / (165 + mt->o_slope);
> +
> + return (format_2 - tmp) * 100;
> +}
> +
> /**
> * mtk_thermal_get_bank - get bank
> * @bank: The bank
> @@ -594,9 +652,13 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> raw = readl(mt->thermal_base +
> conf->msr[conf->bank_data[bank->id].sensors[i]]);
>
> - temp = raw_to_mcelsius_v1(mt,
> - conf->bank_data[bank->id].sensors[i],
> - raw);
> + if (mt->conf->version == MTK_THERMAL_V1) {
> + temp = raw_to_mcelsius_v1(
> + mt, conf->bank_data[bank->id].sensors[i], raw);
> + } else {
> + temp = raw_to_mcelsius_v2(
> + mt, conf->bank_data[bank->id].sensors[i], raw);
> + }
>
> /*
> * The first read of a sensor often contains very high bogus
> @@ -698,9 +760,11 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
> writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
> controller_base + TEMP_ADCMUXADDR);
>
> - /* AHB address for pnp sensor mux selection */
> - writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
> - controller_base + TEMP_PNPMUXADDR);
> + if (mt->conf->version == MTK_THERMAL_V1) {
> + /* AHB address for pnp sensor mux selection */
> + writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
> + controller_base + TEMP_PNPMUXADDR);
> + }
>
> /* AHB value for auxadc enable */
> writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCEN);
> @@ -803,6 +867,23 @@ static int mtk_thermal_extract_efuse_v1(struct mtk_thermal *mt, u32 *buf)
> return 0;
> }
>
> +static int mtk_thermal_extract_efuse_v2(struct mtk_thermal *mt, u32 *buf)
> +{
> + if (!CALIB_BUF1_VALID_V2(buf[1]))
> + return -EINVAL;
> +
> + mt->adc_oe = CALIB_BUF0_ADC_OE_V2(buf[0]);
> + mt->adc_ge = CALIB_BUF0_ADC_GE_V2(buf[0]);
> + mt->degc_cali = CALIB_BUF0_DEGC_CALI_V2(buf[0]);
> + mt->o_slope = CALIB_BUF0_O_SLOPE_V2(buf[0]);
> + mt->vts[VTS1] = CALIB_BUF1_VTS_TS1_V2(buf[1]);
> + mt->vts[VTS2] = CALIB_BUF1_VTS_TS2_V2(buf[1]);
> + mt->vts[VTSABB] = CALIB_BUF1_VTS_TSABB_V2(buf[1]);
> + mt->o_slope_sign = CALIB_BUF1_O_SLOPE_SIGN_V2(buf[1]);
> +
> + return 0;
> +}
> +
> static int mtk_thermal_get_calibration_data(struct device *dev,
> struct mtk_thermal *mt)
> {
> @@ -838,8 +919,15 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
> goto out;
> }
>
> - if (mtk_thermal_extract_efuse_v1(mt, buf))
> + if (mt->conf->version == MTK_THERMAL_V1)
> + ret = mtk_thermal_extract_efuse_v1(mt, buf);
> + else
> + ret = mtk_thermal_extract_efuse_v2(mt, buf);
> +
> + if (ret) {
> dev_info(dev, "Device not calibrated, using default calibration values\n");
> + ret = 0;
> + }
>
> out:
> kfree(buf);
> @@ -872,6 +960,28 @@ static const struct of_device_id mtk_thermal_of_match[] = {
> };
> MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);
>
> +static void mtk_thermal_turn_on_buffer(void __iomem *apmixed_base)
> +{
> + int tmp;
> +
> + tmp = readl(apmixed_base + APMIXED_SYS_TS_CON1);
> + tmp &= ~(0x37);
> + tmp |= 0x1;
> + writel(tmp, apmixed_base + APMIXED_SYS_TS_CON1);
> + udelay(200);
> +}
> +
> +static void mtk_thermal_release_periodic_ts(struct mtk_thermal *mt,
> + void __iomem *auxadc_base)
> +{
> + int tmp;
> +
> + writel(0x800, auxadc_base + AUXADC_CON1_SET_V);
> + writel(0x1, mt->thermal_base + TEMP_MONCTL0);
> + tmp = readl(mt->thermal_base + TEMP_MSRCTL1);
> + writel((tmp & (~0x10e)), mt->thermal_base + TEMP_MSRCTL1);
> +}
> +
> static int mtk_thermal_probe(struct platform_device *pdev)
> {
> int ret, i, ctrl_id;
> @@ -880,6 +990,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> struct resource *res;
> u64 auxadc_phys_base, apmixed_phys_base;
> struct thermal_zone_device *tzdev;
> + void __iomem *apmixed_base, *auxadc_base;
>
> mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
> if (!mt)
> @@ -914,6 +1025,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> return -ENODEV;
> }
>
> + auxadc_base = of_iomap(auxadc, 0);
> auxadc_phys_base = of_get_phys_base(auxadc);
>
> of_node_put(auxadc);
> @@ -929,6 +1041,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> return -ENODEV;
> }
>
> + apmixed_base = of_iomap(apmixedsys, 0);
> apmixed_phys_base = of_get_phys_base(apmixedsys);
>
> of_node_put(apmixedsys);
> @@ -954,6 +1067,11 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> goto err_disable_clk_auxadc;
> }
>
> + if (mt->conf->version == MTK_THERMAL_V2) {
> + mtk_thermal_turn_on_buffer(apmixed_base);
> + mtk_thermal_release_periodic_ts(mt, auxadc_base);
> + }
> +
> for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
> for (i = 0; i < mt->conf->num_banks; i++)
> mtk_thermal_init_bank(mt, i, apmixed_phys_base,
Just gently ping.
Many thanks.
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms
2020-04-30 9:14 ` [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms Henry Yen
2020-07-10 9:58 ` mtk17045
@ 2020-07-10 15:19 ` Matthias Brugger
2020-07-30 17:52 ` Aw: " Frank Wunderlich
1 sibling, 1 reply; 11+ messages in thread
From: Matthias Brugger @ 2020-07-10 15:19 UTC (permalink / raw)
To: Henry Yen, Zhang Rui, Daniel Lezcano, Amit Kucheria
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Michael Kao
On 30/04/2020 11:14, Henry Yen wrote:
> It is known that Mediatek owns two thermal systems, which only differ
> in the way of reading calibration data and converting temperature.
> MT8173, MT8183, MT2701 and MT2712 belongs to version 1 thermal
> system, and MT7622 belongs to version 2.
>
> In order to handle both systems, the suffix _V1 is appended to the
> current code, and then the second patch will add _V2 functions with
> the same purpose but different implementation.
>
> Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
> ---
> drivers/thermal/mtk_thermal.c | 114 ++++++++++++++++++----------------
> 1 file changed, 62 insertions(+), 52 deletions(-)
>
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 76e30603d4d5..10107d9d56a8 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -120,18 +120,18 @@
> * MT2701 has 3 sensors and needs 3 VTS calibration data.
> * MT2712 has 4 sensors and needs 4 VTS calibration data.
> */
> -#define CALIB_BUF0_VALID BIT(0)
> -#define CALIB_BUF1_ADC_GE(x) (((x) >> 22) & 0x3ff)
> -#define CALIB_BUF0_VTS_TS1(x) (((x) >> 17) & 0x1ff)
> -#define CALIB_BUF0_VTS_TS2(x) (((x) >> 8) & 0x1ff)
> -#define CALIB_BUF1_VTS_TS3(x) (((x) >> 0) & 0x1ff)
> -#define CALIB_BUF2_VTS_TS4(x) (((x) >> 23) & 0x1ff)
> -#define CALIB_BUF2_VTS_TS5(x) (((x) >> 5) & 0x1ff)
> -#define CALIB_BUF2_VTS_TSABB(x) (((x) >> 14) & 0x1ff)
> -#define CALIB_BUF0_DEGC_CALI(x) (((x) >> 1) & 0x3f)
> -#define CALIB_BUF0_O_SLOPE(x) (((x) >> 26) & 0x3f)
> -#define CALIB_BUF0_O_SLOPE_SIGN(x) (((x) >> 7) & 0x1)
> -#define CALIB_BUF1_ID(x) (((x) >> 9) & 0x1)
> +#define CALIB_BUF0_VALID_V1 BIT(0)
> +#define CALIB_BUF1_ADC_GE_V1(x) (((x) >> 22) & 0x3ff)
> +#define CALIB_BUF0_VTS_TS1_V1(x) (((x) >> 17) & 0x1ff)
> +#define CALIB_BUF0_VTS_TS2_V1(x) (((x) >> 8) & 0x1ff)
> +#define CALIB_BUF1_VTS_TS3_V1(x) (((x) >> 0) & 0x1ff)
> +#define CALIB_BUF2_VTS_TS4_V1(x) (((x) >> 23) & 0x1ff)
> +#define CALIB_BUF2_VTS_TS5_V1(x) (((x) >> 5) & 0x1ff)
> +#define CALIB_BUF2_VTS_TSABB_V1(x) (((x) >> 14) & 0x1ff)
> +#define CALIB_BUF0_DEGC_CALI_V1(x) (((x) >> 1) & 0x3f)
> +#define CALIB_BUF0_O_SLOPE_V1(x) (((x) >> 26) & 0x3f)
> +#define CALIB_BUF0_O_SLOPE_SIGN_V1(x) (((x) >> 7) & 0x1)
> +#define CALIB_BUF1_ID_V1(x) (((x) >> 9) & 0x1)
>
> enum {
> VTS1,
> @@ -525,7 +525,7 @@ static const struct mtk_thermal_data mt8183_thermal_data = {
> * This converts the raw ADC value to mcelsius using the SoC specific
> * calibration constants
> */
> -static int raw_to_mcelsius(struct mtk_thermal *mt, int sensno, s32 raw)
> +static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
> {
> s32 tmp;
>
> @@ -594,9 +594,9 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> raw = readl(mt->thermal_base +
> conf->msr[conf->bank_data[bank->id].sensors[i]]);
>
> - temp = raw_to_mcelsius(mt,
> - conf->bank_data[bank->id].sensors[i],
> - raw);
> + temp = raw_to_mcelsius_v1(mt,
> + conf->bank_data[bank->id].sensors[i],
> + raw);
>
> /*
> * The first read of a sensor often contains very high bogus
> @@ -758,6 +758,51 @@ static u64 of_get_phys_base(struct device_node *np)
> return of_translate_address(np, regaddr_p);
> }
>
> +static int mtk_thermal_extract_efuse_v1(struct mtk_thermal *mt, u32 *buf)
> +{
> + int i;
> +
> + if (!(buf[0] & CALIB_BUF0_VALID_V1))
> + return -EINVAL;
> +
> + mt->adc_ge = CALIB_BUF1_ADC_GE_V1(buf[1]);
> +
> + for (i = 0; i < mt->conf->num_sensors; i++) {
> + switch (mt->conf->vts_index[i]) {
> + case VTS1:
> + mt->vts[VTS1] = CALIB_BUF0_VTS_TS1_V1(buf[0]);
> + break;
> + case VTS2:
> + mt->vts[VTS2] = CALIB_BUF0_VTS_TS2_V1(buf[0]);
> + break;
> + case VTS3:
> + mt->vts[VTS3] = CALIB_BUF1_VTS_TS3_V1(buf[1]);
> + break;
> + case VTS4:
> + mt->vts[VTS4] = CALIB_BUF2_VTS_TS4_V1(buf[2]);
> + break;
> + case VTS5:
> + mt->vts[VTS5] = CALIB_BUF2_VTS_TS5_V1(buf[2]);
> + break;
> + case VTSABB:
> + mt->vts[VTSABB] =
> + CALIB_BUF2_VTS_TSABB_V1(buf[2]);
> + break;
> + default:
> + break;
> + }
> + }
> +
> + mt->degc_cali = CALIB_BUF0_DEGC_CALI_V1(buf[0]);
> + if (CALIB_BUF1_ID_V1(buf[1]) &
> + CALIB_BUF0_O_SLOPE_SIGN_V1(buf[0]))
> + mt->o_slope = -CALIB_BUF0_O_SLOPE_V1(buf[0]);
> + else
> + mt->o_slope = CALIB_BUF0_O_SLOPE_V1(buf[0]);
> +
> + return 0;
> +}
> +
> static int mtk_thermal_get_calibration_data(struct device *dev,
> struct mtk_thermal *mt)
> {
> @@ -793,43 +838,8 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
> goto out;
> }
>
> - if (buf[0] & CALIB_BUF0_VALID) {
> - mt->adc_ge = CALIB_BUF1_ADC_GE(buf[1]);
> -
> - for (i = 0; i < mt->conf->num_sensors; i++) {
> - switch (mt->conf->vts_index[i]) {
> - case VTS1:
> - mt->vts[VTS1] = CALIB_BUF0_VTS_TS1(buf[0]);
> - break;
> - case VTS2:
> - mt->vts[VTS2] = CALIB_BUF0_VTS_TS2(buf[0]);
> - break;
> - case VTS3:
> - mt->vts[VTS3] = CALIB_BUF1_VTS_TS3(buf[1]);
> - break;
> - case VTS4:
> - mt->vts[VTS4] = CALIB_BUF2_VTS_TS4(buf[2]);
> - break;
> - case VTS5:
> - mt->vts[VTS5] = CALIB_BUF2_VTS_TS5(buf[2]);
> - break;
> - case VTSABB:
> - mt->vts[VTSABB] = CALIB_BUF2_VTS_TSABB(buf[2]);
> - break;
> - default:
> - break;
> - }
> - }
> -
> - mt->degc_cali = CALIB_BUF0_DEGC_CALI(buf[0]);
> - if (CALIB_BUF1_ID(buf[1]) &
> - CALIB_BUF0_O_SLOPE_SIGN(buf[0]))
> - mt->o_slope = -CALIB_BUF0_O_SLOPE(buf[0]);
> - else
> - mt->o_slope = CALIB_BUF0_O_SLOPE(buf[0]);
> - } else {
> + if (mtk_thermal_extract_efuse_v1(mt, buf))
> dev_info(dev, "Device not calibrated, using default calibration values\n");
> - }
>
> out:
> kfree(buf);
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system
2020-04-30 9:14 ` [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system Henry Yen
2020-07-10 10:02 ` mtk17045
@ 2020-07-10 15:23 ` Matthias Brugger
2020-07-30 17:45 ` Aw: " Frank Wunderlich
1 sibling, 1 reply; 11+ messages in thread
From: Matthias Brugger @ 2020-07-10 15:23 UTC (permalink / raw)
To: Henry Yen, Zhang Rui, Daniel Lezcano, Amit Kucheria
Cc: linux-pm, linux-arm-kernel, linux-mediatek, linux-kernel,
Steven Liu, Michael Kao
On 30/04/2020 11:14, Henry Yen wrote:
> This patch adds full support for ver 2 thermal system (e.g., MT7622 SoC).
> The new changes include reading calibration data, converting temperature
> and hardware initialization which are specific for version 2 system.
> Each platform decides which function to call according to its version.
>
> Fixes: 3966be3c08c3 ("thermal: mediatek: add support for MT7622 SoC")
> Signed-off-by: Henry Yen <henry.yen@mediatek.com>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
> ---
> drivers/thermal/mtk_thermal.c | 132 ++++++++++++++++++++++++++++++++--
> 1 file changed, 125 insertions(+), 7 deletions(-)
>
> diff --git a/drivers/thermal/mtk_thermal.c b/drivers/thermal/mtk_thermal.c
> index 10107d9d56a8..88620f7e9890 100644
> --- a/drivers/thermal/mtk_thermal.c
> +++ b/drivers/thermal/mtk_thermal.c
> @@ -38,6 +38,7 @@
> #define TEMP_MONIDET0 0x014
> #define TEMP_MONIDET1 0x018
> #define TEMP_MSRCTL0 0x038
> +#define TEMP_MSRCTL1 0x03c
> #define TEMP_AHBPOLL 0x040
> #define TEMP_AHBTO 0x044
> #define TEMP_ADCPNP0 0x048
> @@ -133,6 +134,20 @@
> #define CALIB_BUF0_O_SLOPE_SIGN_V1(x) (((x) >> 7) & 0x1)
> #define CALIB_BUF1_ID_V1(x) (((x) >> 9) & 0x1)
>
> +/*
> + * Layout of the fuses providing the calibration data
> + * These macros could be used for MT7622.
> + */
> +#define CALIB_BUF0_ADC_OE_V2(x) (((x) >> 22) & 0x3ff)
> +#define CALIB_BUF0_ADC_GE_V2(x) (((x) >> 12) & 0x3ff)
> +#define CALIB_BUF0_DEGC_CALI_V2(x) (((x) >> 6) & 0x3f)
> +#define CALIB_BUF0_O_SLOPE_V2(x) (((x) >> 0) & 0x3f)
> +#define CALIB_BUF1_VTS_TS1_V2(x) (((x) >> 23) & 0x1ff)
> +#define CALIB_BUF1_VTS_TS2_V2(x) (((x) >> 14) & 0x1ff)
> +#define CALIB_BUF1_VTS_TSABB_V2(x) (((x) >> 5) & 0x1ff)
> +#define CALIB_BUF1_VALID_V2(x) (((x) >> 4) & 0x1)
> +#define CALIB_BUF1_O_SLOPE_SIGN_V2(x) (((x) >> 3) & 0x1)
> +
> enum {
> VTS1,
> VTS2,
> @@ -143,6 +158,11 @@ enum {
> MAX_NUM_VTS,
> };
>
> +enum mtk_thermal_version {
> + MTK_THERMAL_V1 = 1,
> + MTK_THERMAL_V2,
> +};
> +
> /* MT2701 thermal sensors */
> #define MT2701_TS1 0
> #define MT2701_TS2 1
> @@ -245,6 +265,7 @@ struct mtk_thermal_data {
> const int *controller_offset;
> bool need_switch_bank;
> struct thermal_bank_cfg bank_data[MAX_NUM_ZONES];
> + enum mtk_thermal_version version;
> };
>
> struct mtk_thermal {
> @@ -258,8 +279,10 @@ struct mtk_thermal {
>
> /* Calibration values */
> s32 adc_ge;
> + s32 adc_oe;
> s32 degc_cali;
> s32 o_slope;
> + s32 o_slope_sign;
> s32 vts[MAX_NUM_VTS];
>
> const struct mtk_thermal_data *conf;
> @@ -398,6 +421,7 @@ static const struct mtk_thermal_data mt8173_thermal_data = {
> .msr = mt8173_msr,
> .adcpnp = mt8173_adcpnp,
> .sensor_mux_values = mt8173_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /*
> @@ -428,6 +452,7 @@ static const struct mtk_thermal_data mt2701_thermal_data = {
> .msr = mt2701_msr,
> .adcpnp = mt2701_adcpnp,
> .sensor_mux_values = mt2701_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /*
> @@ -458,6 +483,7 @@ static const struct mtk_thermal_data mt2712_thermal_data = {
> .msr = mt2712_msr,
> .adcpnp = mt2712_adcpnp,
> .sensor_mux_values = mt2712_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /*
> @@ -482,6 +508,7 @@ static const struct mtk_thermal_data mt7622_thermal_data = {
> .msr = mt7622_msr,
> .adcpnp = mt7622_adcpnp,
> .sensor_mux_values = mt7622_mux_values,
> + .version = MTK_THERMAL_V2,
> };
>
> /*
> @@ -514,6 +541,7 @@ static const struct mtk_thermal_data mt8183_thermal_data = {
> .msr = mt8183_msr,
> .adcpnp = mt8183_adcpnp,
> .sensor_mux_values = mt8183_mux_values,
> + .version = MTK_THERMAL_V1,
> };
>
> /**
> @@ -540,6 +568,36 @@ static int raw_to_mcelsius_v1(struct mtk_thermal *mt, int sensno, s32 raw)
> return mt->degc_cali * 500 - tmp;
> }
>
> +static int raw_to_mcelsius_v2(struct mtk_thermal *mt, int sensno, s32 raw)
> +{
> + s32 format_1 = 0;
> + s32 format_2 = 0;
> + s32 g_oe = 1;
> + s32 g_gain = 1;
> + s32 g_x_roomt = 0;
> + s32 tmp = 0;
> +
> + if (raw == 0)
> + return 0;
> +
> + raw &= 0xfff;
> + g_gain = 10000 + (((mt->adc_ge - 512) * 10000) >> 12);
> + g_oe = mt->adc_oe - 512;
> + format_1 = mt->vts[VTS2] + 3105 - g_oe;
> + format_2 = (mt->degc_cali * 10) >> 1;
> + g_x_roomt = (((format_1 * 10000) >> 12) * 10000) / g_gain;
> +
> + tmp = (((((raw - g_oe) * 10000) >> 12) * 10000) / g_gain) - g_x_roomt;
> + tmp = tmp * 10 * 100 / 11;
> +
> + if (mt->o_slope_sign == 0)
> + tmp = tmp / (165 - mt->o_slope);
> + else
> + tmp = tmp / (165 + mt->o_slope);
> +
> + return (format_2 - tmp) * 100;
> +}
> +
> /**
> * mtk_thermal_get_bank - get bank
> * @bank: The bank
> @@ -594,9 +652,13 @@ static int mtk_thermal_bank_temperature(struct mtk_thermal_bank *bank)
> raw = readl(mt->thermal_base +
> conf->msr[conf->bank_data[bank->id].sensors[i]]);
>
> - temp = raw_to_mcelsius_v1(mt,
> - conf->bank_data[bank->id].sensors[i],
> - raw);
> + if (mt->conf->version == MTK_THERMAL_V1) {
> + temp = raw_to_mcelsius_v1(
> + mt, conf->bank_data[bank->id].sensors[i], raw);
> + } else {
> + temp = raw_to_mcelsius_v2(
> + mt, conf->bank_data[bank->id].sensors[i], raw);
> + }
>
> /*
> * The first read of a sensor often contains very high bogus
> @@ -698,9 +760,11 @@ static void mtk_thermal_init_bank(struct mtk_thermal *mt, int num,
> writel(auxadc_phys_base + AUXADC_CON1_CLR_V,
> controller_base + TEMP_ADCMUXADDR);
>
> - /* AHB address for pnp sensor mux selection */
> - writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
> - controller_base + TEMP_PNPMUXADDR);
> + if (mt->conf->version == MTK_THERMAL_V1) {
> + /* AHB address for pnp sensor mux selection */
> + writel(apmixed_phys_base + APMIXED_SYS_TS_CON1,
> + controller_base + TEMP_PNPMUXADDR);
> + }
>
> /* AHB value for auxadc enable */
> writel(BIT(conf->auxadc_channel), controller_base + TEMP_ADCEN);
> @@ -803,6 +867,23 @@ static int mtk_thermal_extract_efuse_v1(struct mtk_thermal *mt, u32 *buf)
> return 0;
> }
>
> +static int mtk_thermal_extract_efuse_v2(struct mtk_thermal *mt, u32 *buf)
> +{
> + if (!CALIB_BUF1_VALID_V2(buf[1]))
> + return -EINVAL;
> +
> + mt->adc_oe = CALIB_BUF0_ADC_OE_V2(buf[0]);
> + mt->adc_ge = CALIB_BUF0_ADC_GE_V2(buf[0]);
> + mt->degc_cali = CALIB_BUF0_DEGC_CALI_V2(buf[0]);
> + mt->o_slope = CALIB_BUF0_O_SLOPE_V2(buf[0]);
> + mt->vts[VTS1] = CALIB_BUF1_VTS_TS1_V2(buf[1]);
> + mt->vts[VTS2] = CALIB_BUF1_VTS_TS2_V2(buf[1]);
> + mt->vts[VTSABB] = CALIB_BUF1_VTS_TSABB_V2(buf[1]);
> + mt->o_slope_sign = CALIB_BUF1_O_SLOPE_SIGN_V2(buf[1]);
> +
> + return 0;
> +}
> +
> static int mtk_thermal_get_calibration_data(struct device *dev,
> struct mtk_thermal *mt)
> {
> @@ -838,8 +919,15 @@ static int mtk_thermal_get_calibration_data(struct device *dev,
> goto out;
> }
>
> - if (mtk_thermal_extract_efuse_v1(mt, buf))
> + if (mt->conf->version == MTK_THERMAL_V1)
> + ret = mtk_thermal_extract_efuse_v1(mt, buf);
> + else
> + ret = mtk_thermal_extract_efuse_v2(mt, buf);
> +
> + if (ret) {
> dev_info(dev, "Device not calibrated, using default calibration values\n");
> + ret = 0;
> + }
>
> out:
> kfree(buf);
> @@ -872,6 +960,28 @@ static const struct of_device_id mtk_thermal_of_match[] = {
> };
> MODULE_DEVICE_TABLE(of, mtk_thermal_of_match);
>
> +static void mtk_thermal_turn_on_buffer(void __iomem *apmixed_base)
> +{
> + int tmp;
> +
> + tmp = readl(apmixed_base + APMIXED_SYS_TS_CON1);
> + tmp &= ~(0x37);
> + tmp |= 0x1;
> + writel(tmp, apmixed_base + APMIXED_SYS_TS_CON1);
> + udelay(200);
> +}
> +
> +static void mtk_thermal_release_periodic_ts(struct mtk_thermal *mt,
> + void __iomem *auxadc_base)
> +{
> + int tmp;
> +
> + writel(0x800, auxadc_base + AUXADC_CON1_SET_V);
> + writel(0x1, mt->thermal_base + TEMP_MONCTL0);
> + tmp = readl(mt->thermal_base + TEMP_MSRCTL1);
> + writel((tmp & (~0x10e)), mt->thermal_base + TEMP_MSRCTL1);
> +}
> +
> static int mtk_thermal_probe(struct platform_device *pdev)
> {
> int ret, i, ctrl_id;
> @@ -880,6 +990,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> struct resource *res;
> u64 auxadc_phys_base, apmixed_phys_base;
> struct thermal_zone_device *tzdev;
> + void __iomem *apmixed_base, *auxadc_base;
>
> mt = devm_kzalloc(&pdev->dev, sizeof(*mt), GFP_KERNEL);
> if (!mt)
> @@ -914,6 +1025,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> return -ENODEV;
> }
>
> + auxadc_base = of_iomap(auxadc, 0);
> auxadc_phys_base = of_get_phys_base(auxadc);
>
> of_node_put(auxadc);
> @@ -929,6 +1041,7 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> return -ENODEV;
> }
>
> + apmixed_base = of_iomap(apmixedsys, 0);
> apmixed_phys_base = of_get_phys_base(apmixedsys);
>
> of_node_put(apmixedsys);
> @@ -954,6 +1067,11 @@ static int mtk_thermal_probe(struct platform_device *pdev)
> goto err_disable_clk_auxadc;
> }
>
> + if (mt->conf->version == MTK_THERMAL_V2) {
> + mtk_thermal_turn_on_buffer(apmixed_base);
> + mtk_thermal_release_periodic_ts(mt, auxadc_base);
> + }
> +
> for (ctrl_id = 0; ctrl_id < mt->conf->num_controller ; ctrl_id++)
> for (i = 0; i < mt->conf->num_banks; i++)
> mtk_thermal_init_bank(mt, i, apmixed_phys_base,
>
^ permalink raw reply [flat|nested] 11+ messages in thread
* Aw: Re: [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system
2020-07-10 15:23 ` Matthias Brugger
@ 2020-07-30 17:45 ` Frank Wunderlich
2020-07-31 9:41 ` Daniel Lezcano
0 siblings, 1 reply; 11+ messages in thread
From: Frank Wunderlich @ 2020-07-30 17:45 UTC (permalink / raw)
To: Matthias Brugger
Cc: Henry Yen, Zhang Rui, Daniel Lezcano, Amit Kucheria, Steven Liu,
linux-pm, linux-kernel, Michael Kao, linux-mediatek,
linux-arm-kernel
Tested on bpi-r64 and r2, i hope this can be merged to next / 5.9
Tested-By: Frank Wunderlich <frank-w@public-files.de>
regards Frank
^ permalink raw reply [flat|nested] 11+ messages in thread
* Aw: Re: [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms
2020-07-10 15:19 ` Matthias Brugger
@ 2020-07-30 17:52 ` Frank Wunderlich
0 siblings, 0 replies; 11+ messages in thread
From: Frank Wunderlich @ 2020-07-30 17:52 UTC (permalink / raw)
To: Matthias Brugger
Cc: Henry Yen, Zhang Rui, Daniel Lezcano, Amit Kucheria, Steven Liu,
linux-pm, linux-kernel, Michael Kao, linux-mediatek,
linux-arm-kernel
Tested on bpi-r64 and r2, i hope this can be merged to next / 5.9
Tested-By: Frank Wunderlich <frank-w@public-files.de>
regards Frank
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: Aw: Re: [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system
2020-07-30 17:45 ` Aw: " Frank Wunderlich
@ 2020-07-31 9:41 ` Daniel Lezcano
0 siblings, 0 replies; 11+ messages in thread
From: Daniel Lezcano @ 2020-07-31 9:41 UTC (permalink / raw)
To: Frank Wunderlich, Matthias Brugger
Cc: Henry Yen, Zhang Rui, Amit Kucheria, Steven Liu, linux-pm,
linux-kernel, Michael Kao, linux-mediatek, linux-arm-kernel
On 30/07/2020 19:45, Frank Wunderlich wrote:
> Tested on bpi-r64 and r2, i hope this can be merged to next / 5.9
>
> Tested-By: Frank Wunderlich <frank-w@public-files.de>
Thanks for testing, applied for v5.9
--
<http://www.linaro.org/> Linaro.org │ Open source software for ARM SoCs
Follow Linaro: <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog
^ permalink raw reply [flat|nested] 11+ messages in thread
end of thread, other threads:[~2020-07-31 9:41 UTC | newest]
Thread overview: 11+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2020-04-30 9:14 [PATCH v2 0/2] Mediatek thermal driver update Henry Yen
2020-04-30 9:14 ` [PATCH v2 1/2] thermal: mediatek: prepare to add support for other platforms Henry Yen
2020-07-10 9:58 ` mtk17045
2020-07-10 15:19 ` Matthias Brugger
2020-07-30 17:52 ` Aw: " Frank Wunderlich
2020-04-30 9:14 ` [PATCH v2 2/2] thermal: mediatek: add tsensor support for V2 thermal system Henry Yen
2020-07-10 10:02 ` mtk17045
2020-07-10 15:23 ` Matthias Brugger
2020-07-30 17:45 ` Aw: " Frank Wunderlich
2020-07-31 9:41 ` Daniel Lezcano
2020-07-10 9:54 ` [RESEND] Mediatek thermal driver update mtk17045
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).