From: k.konieczny@partner.samsung.com
To: k.konieczny@partner.samsung.com
Cc: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>,
Marek Szyprowski <m.szyprowski@samsung.com>,
Chanwoo Choi <cw00.choi@samsung.com>,
Krzysztof Kozlowski <krzk@kernel.org>,
Kukjin Kim <kgene@kernel.org>,
Kyungmin Park <kyungmin.park@samsung.com>,
Mark Rutland <mark.rutland@arm.com>,
MyungJoo Ham <myungjoo.ham@samsung.com>,
Nishanth Menon <nm@ti.com>, Rob Herring <robh+dt@kernel.org>,
Stephen Boyd <sboyd@kernel.org>,
Viresh Kumar <vireshk@kernel.org>,
devicetree@vger.kernel.org, linux-arm-kernel@lists.infradead.org,
linux-kernel@vger.kernel.org, linux-pm@vger.kernel.org,
linux-samsung-soc@vger.kernel.org
Subject: [PATCH v3 3/5] devfreq: exynos-bus: convert to use dev_pm_opp_set_rate()
Date: Fri, 19 Jul 2019 17:05:33 +0200 [thread overview]
Message-ID: <20190719150535.15501-4-k.konieczny@partner.samsung.com> (raw)
In-Reply-To: <20190719150535.15501-1-k.konieczny@partner.samsung.com>
Reuse opp core code for setting bus clock and voltage. As a side
effect this allow useage of coupled regulators feature (required
for boards using Exynos5422/5800 SoCs) because dev_pm_opp_set_rate()
uses regulator_set_voltage_triplet() for setting regulator voltage
while the old code used regulator_set_voltage_tol() with fixed
tolerance. This patch also removes no longer needed parsing of DT
property "exynos,voltage-tolerance" (no Exynos devfreq DT node uses
it).
Signed-off-by: Kamil Konieczny <k.konieczny@partner.samsung.com>
---
drivers/devfreq/exynos-bus.c | 143 +++++++++--------------------------
1 file changed, 37 insertions(+), 106 deletions(-)
diff --git a/drivers/devfreq/exynos-bus.c b/drivers/devfreq/exynos-bus.c
index f391044aa39d..c2147b0912a0 100644
--- a/drivers/devfreq/exynos-bus.c
+++ b/drivers/devfreq/exynos-bus.c
@@ -25,7 +25,6 @@
#include <linux/slab.h>
#define DEFAULT_SATURATION_RATIO 40
-#define DEFAULT_VOLTAGE_TOLERANCE 2
struct exynos_bus {
struct device *dev;
@@ -37,9 +36,9 @@ struct exynos_bus {
unsigned long curr_freq;
- struct regulator *regulator;
+ struct opp_table *opp_table;
+
struct clk *clk;
- unsigned int voltage_tolerance;
unsigned int ratio;
};
@@ -99,56 +98,23 @@ static int exynos_bus_target(struct device *dev, unsigned long *freq, u32 flags)
{
struct exynos_bus *bus = dev_get_drvdata(dev);
struct dev_pm_opp *new_opp;
- unsigned long old_freq, new_freq, new_volt, tol;
int ret = 0;
- /* Get new opp-bus instance according to new bus clock */
+ /* Get correct frequency for bus. */
new_opp = devfreq_recommended_opp(dev, freq, flags);
if (IS_ERR(new_opp)) {
dev_err(dev, "failed to get recommended opp instance\n");
return PTR_ERR(new_opp);
}
- new_freq = dev_pm_opp_get_freq(new_opp);
- new_volt = dev_pm_opp_get_voltage(new_opp);
dev_pm_opp_put(new_opp);
- old_freq = bus->curr_freq;
-
- if (old_freq == new_freq)
- return 0;
- tol = new_volt * bus->voltage_tolerance / 100;
-
/* Change voltage and frequency according to new OPP level */
mutex_lock(&bus->lock);
+ ret = dev_pm_opp_set_rate(dev, *freq);
+ if (!ret)
+ bus->curr_freq = *freq;
- if (old_freq < new_freq) {
- ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol);
- if (ret < 0) {
- dev_err(bus->dev, "failed to set voltage\n");
- goto out;
- }
- }
-
- ret = clk_set_rate(bus->clk, new_freq);
- if (ret < 0) {
- dev_err(dev, "failed to change clock of bus\n");
- clk_set_rate(bus->clk, old_freq);
- goto out;
- }
-
- if (old_freq > new_freq) {
- ret = regulator_set_voltage_tol(bus->regulator, new_volt, tol);
- if (ret < 0) {
- dev_err(bus->dev, "failed to set voltage\n");
- goto out;
- }
- }
- bus->curr_freq = new_freq;
-
- dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n",
- old_freq, new_freq, clk_get_rate(bus->clk));
-out:
mutex_unlock(&bus->lock);
return ret;
@@ -195,8 +161,8 @@ static void exynos_bus_exit(struct device *dev)
dev_warn(dev, "failed to disable the devfreq-event devices\n");
clk_disable_unprepare(bus->clk);
- if (bus->regulator)
- regulator_disable(bus->regulator);
+ if (bus->opp_table)
+ dev_pm_opp_put_regulators(bus->opp_table);
dev_pm_opp_of_remove_table(dev);
}
@@ -209,39 +175,23 @@ static int exynos_bus_passive_target(struct device *dev, unsigned long *freq,
{
struct exynos_bus *bus = dev_get_drvdata(dev);
struct dev_pm_opp *new_opp;
- unsigned long old_freq, new_freq;
- int ret = 0;
+ int ret;
- /* Get new opp-bus instance according to new bus clock */
+ /* Get correct frequency for bus. */
new_opp = devfreq_recommended_opp(dev, freq, flags);
if (IS_ERR(new_opp)) {
dev_err(dev, "failed to get recommended opp instance\n");
return PTR_ERR(new_opp);
}
- new_freq = dev_pm_opp_get_freq(new_opp);
dev_pm_opp_put(new_opp);
- old_freq = bus->curr_freq;
-
- if (old_freq == new_freq)
- return 0;
-
/* Change the frequency according to new OPP level */
mutex_lock(&bus->lock);
+ ret = dev_pm_opp_set_rate(dev, *freq);
+ if (!ret)
+ bus->curr_freq = *freq;
- ret = clk_set_rate(bus->clk, new_freq);
- if (ret < 0) {
- dev_err(dev, "failed to set the clock of bus\n");
- goto out;
- }
-
- *freq = new_freq;
- bus->curr_freq = new_freq;
-
- dev_dbg(dev, "Set the frequency of bus (%luHz -> %luHz, %luHz)\n",
- old_freq, new_freq, clk_get_rate(bus->clk));
-out:
mutex_unlock(&bus->lock);
return ret;
@@ -259,20 +209,9 @@ static int exynos_bus_parent_parse_of(struct device_node *np,
struct exynos_bus *bus)
{
struct device *dev = bus->dev;
- int i, ret, count, size;
-
- /* Get the regulator to provide each bus with the power */
- bus->regulator = devm_regulator_get(dev, "vdd");
- if (IS_ERR(bus->regulator)) {
- dev_err(dev, "failed to get VDD regulator\n");
- return PTR_ERR(bus->regulator);
- }
-
- ret = regulator_enable(bus->regulator);
- if (ret < 0) {
- dev_err(dev, "failed to enable VDD regulator\n");
- return ret;
- }
+ struct opp_table *opp_table;
+ const char *vdd = "vdd";
+ int i, count, size;
/*
* Get the devfreq-event devices to get the current utilization of
@@ -281,26 +220,29 @@ static int exynos_bus_parent_parse_of(struct device_node *np,
count = devfreq_event_get_edev_count(dev);
if (count < 0) {
dev_err(dev, "failed to get the count of devfreq-event dev\n");
- ret = count;
- goto err_regulator;
+ return count;
}
- bus->edev_count = count;
+ bus->edev_count = count;
size = sizeof(*bus->edev) * count;
bus->edev = devm_kzalloc(dev, size, GFP_KERNEL);
- if (!bus->edev) {
- ret = -ENOMEM;
- goto err_regulator;
- }
+ if (!bus->edev)
+ return -ENOMEM;
for (i = 0; i < count; i++) {
bus->edev[i] = devfreq_event_get_edev_by_phandle(dev, i);
- if (IS_ERR(bus->edev[i])) {
- ret = -EPROBE_DEFER;
- goto err_regulator;
- }
+ if (IS_ERR(bus->edev[i]))
+ return -EPROBE_DEFER;
+ }
+
+ opp_table = dev_pm_opp_set_regulators(dev, &vdd, 1);
+ if (IS_ERR(opp_table)) {
+ i = PTR_ERR(opp_table);
+ dev_err(dev, "failed to set regulators %d\n", i);
+ return i;
}
+ bus->opp_table = opp_table;
/*
* Optionally, Get the saturation ratio according to Exynos SoC
* When measuring the utilization of each AXI bus with devfreq-event
@@ -314,16 +256,7 @@ static int exynos_bus_parent_parse_of(struct device_node *np,
if (of_property_read_u32(np, "exynos,saturation-ratio", &bus->ratio))
bus->ratio = DEFAULT_SATURATION_RATIO;
- if (of_property_read_u32(np, "exynos,voltage-tolerance",
- &bus->voltage_tolerance))
- bus->voltage_tolerance = DEFAULT_VOLTAGE_TOLERANCE;
-
return 0;
-
-err_regulator:
- regulator_disable(bus->regulator);
-
- return ret;
}
static int exynos_bus_parse_of(struct exynos_bus *bus)
@@ -414,12 +347,8 @@ static int exynos_bus_probe(struct platform_device *pdev)
/* Parse the device-tree to get the resource information */
ret = exynos_bus_parse_of(bus);
- if (ret < 0) {
- if (!passive)
- regulator_disable(bus->regulator);
-
- return ret;
- }
+ if (ret < 0)
+ goto err_reg;
if (passive)
goto passive;
@@ -512,10 +441,12 @@ static int exynos_bus_probe(struct platform_device *pdev)
err:
clk_disable_unprepare(bus->clk);
- if (!passive)
- regulator_disable(bus->regulator);
-
dev_pm_opp_of_remove_table(dev);
+err_reg:
+ if (bus->opp_table) {
+ dev_pm_opp_put_regulators(bus->opp_table);
+ bus->opp_table = NULL;
+ }
return ret;
}
--
2.22.0
next prev parent reply other threads:[~2019-07-19 15:06 UTC|newest]
Thread overview: 13+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <CGME20190719150553eucas1p142b965afae13224712d51f9c28162165@eucas1p1.samsung.com>
2019-07-19 15:05 ` [PATCH v3 0/5] add coupled regulators for Exynos5422/5800 k.konieczny
[not found] ` <CGME20190719150553eucas1p1665462f3fc0e06fc9c082e258be3a851@eucas1p1.samsung.com>
2019-07-19 15:05 ` [PATCH v3 1/5] devfreq: exynos-bus: correct clock enable sequence k.konieczny
2019-07-25 9:58 ` Chanwoo Choi
[not found] ` <CGME20190719150554eucas1p2f4c9e4d2767ab740d419c42d4aeed6d5@eucas1p2.samsung.com>
2019-07-19 15:05 ` [PATCH v3 2/5] opp: core: add regulators enable and disable k.konieczny
2019-07-23 1:48 ` Viresh Kumar
[not found] ` <CGME20190719150555eucas1p197adc3c58e45c53137fd70cadbfae60e@eucas1p1.samsung.com>
2019-07-19 15:05 ` k.konieczny [this message]
2019-07-25 10:17 ` [PATCH v3 3/5] devfreq: exynos-bus: convert to use dev_pm_opp_set_rate() Chanwoo Choi
2019-07-25 13:35 ` Kamil Konieczny
2019-07-25 14:53 ` Chanwoo Choi
2019-07-25 15:15 ` Kamil Konieczny
2019-07-26 1:02 ` Chanwoo Choi
[not found] ` <CGME20190719150556eucas1p291b9e533a80d77e2f58452f0e1fe8b35@eucas1p2.samsung.com>
2019-07-19 15:05 ` [PATCH v3 4/5] ARM: dts: exynos: add initial data for coupled regulators for Exynos5422/5800 k.konieczny
[not found] ` <CGME20190719150556eucas1p2bc6f133c48ec1be9b36119a414887969@eucas1p2.samsung.com>
2019-07-19 15:05 ` [PATCH v3 5/5] dt-bindings: devfreq: exynos-bus: remove unused property k.konieczny
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190719150535.15501-4-k.konieczny@partner.samsung.com \
--to=k.konieczny@partner.samsung.com \
--cc=b.zolnierkie@samsung.com \
--cc=cw00.choi@samsung.com \
--cc=devicetree@vger.kernel.org \
--cc=kgene@kernel.org \
--cc=krzk@kernel.org \
--cc=kyungmin.park@samsung.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=linux-samsung-soc@vger.kernel.org \
--cc=m.szyprowski@samsung.com \
--cc=mark.rutland@arm.com \
--cc=myungjoo.ham@samsung.com \
--cc=nm@ti.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=vireshk@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).