Linux-PM Archive on lore.kernel.org
 help / color / Atom feed
From: Ricardo Rivera-Matos <r-rivera-matos@ti.com>
To: <sre@kernel.org>, <pali@kernel.org>, <robh@kernel.org>
Cc: <afd@ti.com>, <r-rivera-matos@ti.com>, <dmurphy@ti.com>,
	<linux-pm@vger.kernel.org>, <linux-kernel@vger.kernel.org>,
	<devicetree@vger.kernel.org>, <sspatil@android.com>
Subject: [PATCH v13 2/4] dt-bindings: power: Convert battery.txt to battery.yaml
Date: Mon, 22 Jun 2020 14:18:35 -0500
Message-ID: <20200622191837.9326-3-r-rivera-matos@ti.com> (raw)
In-Reply-To: <20200622191837.9326-1-r-rivera-matos@ti.com>

From: Dan Murphy <dmurphy@ti.com>

Convert the battery.txt file to yaml and fix up the examples.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
---
 .../bindings/power/supply/battery.txt         |  83 +----------
 .../bindings/power/supply/battery.yaml        | 139 ++++++++++++++++++
 2 files changed, 141 insertions(+), 81 deletions(-)
 create mode 100644 Documentation/devicetree/bindings/power/supply/battery.yaml

diff --git a/Documentation/devicetree/bindings/power/supply/battery.txt b/Documentation/devicetree/bindings/power/supply/battery.txt
index 5e29595edd74..4c5216fcb760 100644
--- a/Documentation/devicetree/bindings/power/supply/battery.txt
+++ b/Documentation/devicetree/bindings/power/supply/battery.txt
@@ -1,87 +1,8 @@
-Battery Characteristics
-
-The devicetree battery node provides static battery characteristics.
-In smart batteries, these are typically stored in non-volatile memory
-on a fuel gauge chip. The battery node should be used where there is
-no appropriate non-volatile memory, or it is unprogrammed/incorrect.
-
-Upstream dts files should not include battery nodes, unless the battery
-represented cannot easily be replaced in the system by one of a
-different type. This prevents unpredictable, potentially harmful,
-behavior should a replacement that changes the battery type occur
-without a corresponding update to the dtb.
+The contents of this file has been moved to battery.yaml
 
 Please note that not all charger drivers respect all of the properties.
 
-Required Properties:
- - compatible: Must be "simple-battery"
-
-Optional Properties:
  - over-voltage-threshold-microvolt: battery over-voltage limit
  - re-charge-voltage-microvolt: limit to automatically start charging again
- - voltage-min-design-microvolt: drained battery voltage
- - voltage-max-design-microvolt: fully charged battery voltage
- - energy-full-design-microwatt-hours: battery design energy
- - charge-full-design-microamp-hours: battery design capacity
  - trickle-charge-current-microamp: current for trickle-charge phase
- - precharge-current-microamp: current for pre-charge phase
- - precharge-upper-limit-microvolt: limit when to change to constant charging
- - charge-term-current-microamp: current for charge termination phase
- - constant-charge-current-max-microamp: maximum constant input current
- - constant-charge-voltage-max-microvolt: maximum constant input voltage
- - factory-internal-resistance-micro-ohms: battery factory internal resistance
- - ocv-capacity-table-0: An array providing the open circuit voltage (OCV)
-   of the battery and corresponding battery capacity percent, which is used
-   to look up battery capacity according to current OCV value. And the open
-   circuit voltage unit is microvolt.
- - ocv-capacity-table-1: Same as ocv-capacity-table-0
- ......
- - ocv-capacity-table-n: Same as ocv-capacity-table-0
- - ocv-capacity-celsius: An array containing the temperature in degree Celsius,
-   for each of the battery capacity lookup table. The first temperature value
-   specifies the OCV table 0, and the second temperature value specifies the
-   OCV table 1, and so on.
- - resistance-temp-table: An array providing the temperature in degree Celsius
-   and corresponding battery internal resistance percent, which is used to look
-   up the resistance percent according to current temperature to get a accurate
-   batterty internal resistance in different temperatures.
-
-Battery properties are named, where possible, for the corresponding
-elements in enum power_supply_property, defined in
-https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/tree/include/linux/power_supply.h
-
-Batteries must be referenced by chargers and/or fuel-gauges
-using a phandle. The phandle's property should be named
-"monitored-battery".
-
-Example:
-
-	bat: battery {
-		compatible = "simple-battery";
-		voltage-min-design-microvolt = <3200000>;
-		voltage-max-design-microvolt = <4200000>;
-		energy-full-design-microwatt-hours = <5290000>;
-		charge-full-design-microamp-hours = <1430000>;
-		precharge-current-microamp = <256000>;
-		charge-term-current-microamp = <128000>;
-		constant-charge-current-max-microamp = <900000>;
-		constant-charge-voltage-max-microvolt = <4200000>;
-		factory-internal-resistance-micro-ohms = <250000>;
-		ocv-capacity-celsius = <(-10) 0 10>;
-		ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>, ...;
-		ocv-capacity-table-1 = <4200000 100>, <4185000 95>, <4113000 90>, ...;
-		ocv-capacity-table-2 = <4250000 100>, <4200000 95>, <4185000 90>, ...;
-		resistance-temp-table = <20 100>, <10 90>, <0 80>, <(-10) 60>;
-	};
-
-	charger: charger@11 {
-		....
-		monitored-battery = <&bat>;
-		...
-	};
-
-	fuel_gauge: fuel-gauge@22 {
-		....
-		monitored-battery = <&bat>;
-		...
-	};
+ - precharge-upper-limit-microvolt: limit when to change to constant charging
\ No newline at end of file
diff --git a/Documentation/devicetree/bindings/power/supply/battery.yaml b/Documentation/devicetree/bindings/power/supply/battery.yaml
new file mode 100644
index 000000000000..a3dca0b0347e
--- /dev/null
+++ b/Documentation/devicetree/bindings/power/supply/battery.yaml
@@ -0,0 +1,139 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/power/supply/battery.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Battery Characteristics
+
+maintainers:
+  - Sebastian Reichel <sre@kernel.org>
+
+description: |
+  The devicetree battery node provides static battery characteristics.
+  In smart batteries, these are typically stored in non-volatile memory
+  on a fuel gauge chip. The battery node should be used where there is
+  no appropriate non-volatile memory, or it is unprogrammed/incorrect.
+
+  Upstream dts files should not include battery nodes, unless the battery
+  represented cannot easily be replaced in the system by one of a
+  different type. This prevents unpredictable, potentially harmful,
+  behavior should a replacement that changes the battery type occur
+  without a corresponding update to the dtb.
+
+  Battery properties are named, where possible, for the corresponding elements
+  in enum power_supply_property, defined in include/linux/power_supply.h
+
+  Batteries must be referenced by chargers and/or fuel-gauges using a phandle.
+  The phandle's property should be named "monitored-battery".
+
+properties:
+  compatible:
+    const: simple-battery
+
+  voltage-min-design-microvolt:
+    description: drained battery voltage
+
+  voltage-max-design-microvolt:
+    description: fully charged battery voltage
+
+  energy-full-design-microwatt-hours:
+    description: battery design energy
+
+  charge-full-design-microamp-hours:
+    description: battery design capacity
+
+  precharge-current-microamp:
+    description: current for pre-charge phase
+
+  charge-term-current-microamp:
+    description: current for charge termination phase
+
+  constant-charge-current-max-microamp:
+    description: maximum constant input current
+
+  constant-charge-voltage-max-microvolt:
+    description: maximum constant input voltage
+
+  factory-internal-resistance-micro-ohms:
+    description: battery factory internal resistance
+
+  monitored-battery:
+    $ref: /schemas/types.yaml#/definitions/phandle
+    description: phandle to the battery node being monitored
+
+required:
+  - compatible
+
+patternProperties:
+  '^ocv-capacity-table-[0-100]$':
+    description: |
+      An array providing the open circuit voltage (OCV)
+      of the battery and corresponding battery capacity percent, which is used
+      to look up battery capacity according to current OCV value. And the open
+      circuit voltage unit is microvolt.
+    maxItems: 100
+    items:
+      items:
+        - description: open circuit voltage (OCV) in microvolts
+        - description: battery capacity percent
+          maximum: 100
+
+  '^resistance-temp-table-[0-100]$':
+    description: |
+      An array providing the temperature in degree Celsius
+      and corresponding battery internal resistance percent, which is used to
+      look up the resistance percent according to current temperature to get an
+      accurate batterty internal resistance in different temperatures.
+    maxItems: 100
+    items:
+      items:
+        - description: internal resistance percent
+        - description: battery capacity percent
+          maximum: 100
+
+  '^ocv-capacity-celsius-[0-100]$':
+    description: |
+      An array containing the temperature in degree Celsius,
+      for each of the battery capacity lookup table.
+    maxItems: 100
+    items:
+      items:
+        - description: temperature in degree Celsius
+        - description: battery capacity percent
+          maximum: 100
+
+additionalProperties: false
+
+examples:
+  - |
+    power {
+      #address-cells = <1>;
+      #size-cells = <0>;
+
+      battery:battery {
+        compatible = "simple-battery";
+        voltage-min-design-microvolt = <3200000>;
+        voltage-max-design-microvolt = <4200000>;
+        energy-full-design-microwatt-hours = <5290000>;
+        charge-full-design-microamp-hours = <1430000>;
+        precharge-current-microamp = <256000>;
+        charge-term-current-microamp = <128000>;
+        constant-charge-current-max-microamp = <900000>;
+        constant-charge-voltage-max-microvolt = <4200000>;
+        factory-internal-resistance-micro-ohms = <250000>;
+        ocv-capacity-celsius-0 = <(-10) 10>;
+        ocv-capacity-table-0 = <4185000 100>, <4113000 95>, <4066000 90>;
+        resistance-temp-table-0 = <20 100>, <10 90>, <0 80>, <(-10) 60>;
+      };
+
+      charger@11 {
+        reg = <0x11>;
+        monitored-battery = <&battery>;
+      };
+
+      fuel-gauge@22 {
+        reg = <0x22>;
+        monitored-battery = <&battery>;
+      };
+    };
\ No newline at end of file
-- 
2.27.0


  parent reply index

Thread overview: 8+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-06-22 19:18 [PATCH v13 0/4] Add JEITA properties and introduce the bq2515x charger Ricardo Rivera-Matos
2020-06-22 19:18 ` [PATCH v13 1/4] power_supply: Add additional health properties to the header Ricardo Rivera-Matos
2020-06-22 19:18 ` Ricardo Rivera-Matos [this message]
2020-06-29 22:56   ` [PATCH v13 2/4] dt-bindings: power: Convert battery.txt to battery.yaml Rob Herring
2020-06-30 12:12     ` Dan Murphy
2020-06-22 19:18 ` [PATCH v13 3/4] dt-bindings: power: Add the bindings for the bq2515x family of chargers Ricardo Rivera-Matos
2020-06-29 22:57   ` Rob Herring
2020-06-22 19:18 ` [PATCH v13 4/4] power: supply: bq25150 introduce the bq25150 Ricardo Rivera-Matos

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200622191837.9326-3-r-rivera-matos@ti.com \
    --to=r-rivera-matos@ti.com \
    --cc=afd@ti.com \
    --cc=devicetree@vger.kernel.org \
    --cc=dmurphy@ti.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pm@vger.kernel.org \
    --cc=pali@kernel.org \
    --cc=robh@kernel.org \
    --cc=sre@kernel.org \
    --cc=sspatil@android.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-PM Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-pm/0 linux-pm/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-pm linux-pm/ https://lore.kernel.org/linux-pm \
		linux-pm@vger.kernel.org
	public-inbox-index linux-pm

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-pm


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git