* [V2, 0/3] Add SC7180 interconnect provider driver
@ 2019-12-31 8:58 Odelu Kukatla
2019-12-31 8:58 ` [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings Odelu Kukatla
` (2 more replies)
0 siblings, 3 replies; 12+ messages in thread
From: Odelu Kukatla @ 2019-12-31 8:58 UTC (permalink / raw)
To: georgi.djakov, daidavid1, bjorn.andersson, evgreen
Cc: sboyd, ilina, seansw, elder, linux-kernel, linux-arm-msm,
linux-pm, linux-arm-msm-owner, Odelu Kukatla
Add driver to support scaling of the on-chip interconnects on
the SC7180-based platforms.
Depends-on: interconnect: qcom: sdm845: Walk the list safely on node removal
Depends-on: Walk the list safely on node removal
Depends-on: Add device tree support for sc7180
Odelu Kukatla (3):
dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
interconnect: qcom: Add SC7180 interconnect provider driver
arm64: dts: sc7180: Add interconnect provider DT nodes
.../bindings/interconnect/qcom,bcm-voter.yaml | 1 +
.../bindings/interconnect/qcom,sc7180.yaml | 155 ++++
arch/arm64/boot/dts/qcom/sc7180.dtsi | 96 +++
drivers/interconnect/qcom/Kconfig | 10 +
drivers/interconnect/qcom/Makefile | 2 +
drivers/interconnect/qcom/bcm-voter.c | 1 +
drivers/interconnect/qcom/sc7180.c | 787 +++++++++++++++++++++
include/dt-bindings/interconnect/qcom,sc7180.h | 161 +++++
8 files changed, 1213 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
create mode 100644 drivers/interconnect/qcom/sc7180.c
create mode 100644 include/dt-bindings/interconnect/qcom,sc7180.h
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply [flat|nested] 12+ messages in thread
* [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
2019-12-31 8:58 [V2, 0/3] Add SC7180 interconnect provider driver Odelu Kukatla
@ 2019-12-31 8:58 ` Odelu Kukatla
2020-01-04 22:01 ` Rob Herring
2019-12-31 8:58 ` [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver Odelu Kukatla
2019-12-31 8:58 ` [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes Odelu Kukatla
2 siblings, 1 reply; 12+ messages in thread
From: Odelu Kukatla @ 2019-12-31 8:58 UTC (permalink / raw)
To: georgi.djakov, daidavid1, bjorn.andersson, evgreen, Andy Gross,
Rob Herring, Mark Rutland, linux-arm-msm, linux-pm, devicetree,
linux-kernel
Cc: sboyd, ilina, seansw, elder, linux-arm-msm-owner, Odelu Kukatla
The Qualcomm SC7180 platform has several bus fabrics that could be
controlled and tuned dynamically according to the bandwidth demand.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
---
.../bindings/interconnect/qcom,bcm-voter.yaml | 1 +
.../bindings/interconnect/qcom,sc7180.yaml | 155 ++++++++++++++++++++
include/dt-bindings/interconnect/qcom,sc7180.h | 161 +++++++++++++++++++++
3 files changed, 317 insertions(+)
create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
create mode 100644 include/dt-bindings/interconnect/qcom,sc7180.h
diff --git a/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml b/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
index 74f0715..55c9f34 100644
--- a/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
+++ b/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
@@ -19,6 +19,7 @@ description: |
properties:
compatible:
enum:
+ - qcom,sc7180-bcm-voter
- qcom,sdm845-bcm-voter
required:
diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
new file mode 100644
index 0000000..487da5e
--- /dev/null
+++ b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
@@ -0,0 +1,155 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/interconnect/qcom,sc7180.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SC7180 Network-On-Chip Interconnect
+
+maintainers:
+ - David Dai <daidavid1@codeaurora.org>
+
+description: |
+ SC7180 interconnect providers support system bandwidth requirements through
+ RPMh hardware accelerators known as Bus Clock Manager (BCM). The provider is
+ able to communicate with the BCM through the Resource State Coordinator (RSC)
+ associated with each execution environment. Provider nodes must point to at
+ least one RPMh device child node pertaining to their RSC and each provider
+ can map to multiple RPMh resources.
+
+properties:
+ reg:
+ maxItems: 1
+
+ compatible:
+ enum:
+ - qcom,sc7180-aggre1-noc
+ - qcom,sc7180-aggre2-noc
+ - qcom,sc7180-camnoc-virt
+ - qcom,sc7180-compute-noc
+ - qcom,sc7180-config-noc
+ - qcom,sc7180-dc-noc
+ - qcom,sc7180-gem-noc
+ - qcom,sc7180-ipa-virt
+ - qcom,sc7180-mc-virt
+ - qcom,sc7180-mmss-noc
+ - qcom,sc7180-npu-noc
+ - qcom,sc7180-qup-virt
+ - qcom,sc7180-system-noc
+
+ '#interconnect-cells':
+ const: 1
+
+ qcom,bcm-voters:
+ $ref: /schemas/types.yaml#/definitions/phandle-array
+ description: |
+ List of phandles to qcom,bcm-voter nodes that are required by
+ this interconnect to send RPMh commands.
+
+ qcom,bcm-voter-names:
+ $ref: /schemas/types.yaml#/definitions/string-array
+ description: |
+ Names for each of the qcom,bcm-voters specified.
+
+required:
+ - compatible
+ - reg
+ - '#interconnect-cells'
+ - qcom,bcm-voters
+
+additionalProperties: false
+
+examples:
+ - |
+ #include <dt-bindings/interconnect/qcom,sc7180.h>
+
+ config_noc: interconnect@1500000 {
+ compatible = "qcom,sc7180-config-noc";
+ reg = <0 0x01500000 0 0x28000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ system_noc: interconnect@1620000 {
+ compatible = "qcom,sc7180-system-noc";
+ reg = <0 0x01620000 0 0x17080>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mc_virt: interconnect@1630000 {
+ compatible = "qcom,sc7180-mc-virt";
+ reg = <0 0x01630000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ qup_virt: interconnect@1650000 {
+ compatible = "qcom,sc7180-qup-virt";
+ reg = <0 0x01650000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre1_noc: interconnect@16e0000 {
+ compatible = "qcom,sc7180-aggre1-noc";
+ reg = <0 0x016e0000 0 0x15080>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre2_noc: interconnect@1700000 {
+ compatible = "qcom,sc7180-aggre2-noc";
+ reg = <0 0x01700000 0 0x1f880>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ compute_noc: interconnect@170e000 {
+ compatible = "qcom,sc7180-compute-noc";
+ reg = <0 0x0170e000 0 0x11880>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mmss_noc: interconnect@1740000 {
+ compatible = "qcom,sc7180-mmss-noc";
+ reg = <0 0x01740000 0 0x1c100>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ ipa_virt: interconnect@1e00000 {
+ compatible = "qcom,sc7180-ipa-virt";
+ reg = <0 0x01e00000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ dc_noc: interconnect@9160000 {
+ compatible = "qcom,sc7180-dc-noc";
+ reg = <0 0x09160000 0 0x03200>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ gem_noc: interconnect@9680000 {
+ compatible = "qcom,sc7180-gem-noc";
+ reg = <0 0x09680000 0 0x3e200>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ npu_noc: interconnect@9990000 {
+ compatible = "qcom,sc7180-npu-noc";
+ reg = <0 0x09990000 0 0x1600>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ camnoc_virt: interconnect@ac00000 {
+ compatible = "qcom,sc7180-camnoc-virt";
+ reg = <0 0x0ac00000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
diff --git a/include/dt-bindings/interconnect/qcom,sc7180.h b/include/dt-bindings/interconnect/qcom,sc7180.h
new file mode 100644
index 0000000..7ed2d82
--- /dev/null
+++ b/include/dt-bindings/interconnect/qcom,sc7180.h
@@ -0,0 +1,161 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Qualcomm SC7180 interconnect IDs
+ *
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ */
+
+#ifndef __DT_BINDINGS_INTERCONNECT_QCOM_SC7180_H
+#define __DT_BINDINGS_INTERCONNECT_QCOM_SC7180_H
+
+#define MASTER_A1NOC_CFG 0
+#define MASTER_QSPI 1
+#define MASTER_QUP_0 2
+#define MASTER_SDCC_2 3
+#define MASTER_EMMC 4
+#define MASTER_UFS_MEM 5
+#define SLAVE_A1NOC_SNOC 6
+#define SLAVE_SERVICE_A1NOC 7
+
+#define MASTER_A2NOC_CFG 0
+#define MASTER_QDSS_BAM 1
+#define MASTER_QUP_1 2
+#define MASTER_USB3 3
+#define MASTER_CRYPTO 4
+#define MASTER_IPA 5
+#define MASTER_QDSS_ETR 6
+#define SLAVE_A2NOC_SNOC 7
+#define SLAVE_SERVICE_A2NOC 8
+
+#define MASTER_CAMNOC_HF0_UNCOMP 0
+#define MASTER_CAMNOC_HF1_UNCOMP 1
+#define MASTER_CAMNOC_SF_UNCOMP 2
+#define SLAVE_CAMNOC_UNCOMP 3
+
+#define MASTER_NPU 0
+#define MASTER_NPU_PROC 1
+#define SLAVE_CDSP_GEM_NOC 2
+
+#define MASTER_SNOC_CNOC 0
+#define MASTER_QDSS_DAP 1
+#define SLAVE_A1NOC_CFG 2
+#define SLAVE_A2NOC_CFG 3
+#define SLAVE_AHB2PHY_SOUTH 4
+#define SLAVE_AHB2PHY_CENTER 5
+#define SLAVE_AOP 6
+#define SLAVE_AOSS 7
+#define SLAVE_BOOT_ROM 8
+#define SLAVE_CAMERA_CFG 9
+#define SLAVE_CAMERA_NRT_THROTTLE_CFG 10
+#define SLAVE_CAMERA_RT_THROTTLE_CFG 11
+#define SLAVE_CLK_CTL 12
+#define SLAVE_RBCPR_CX_CFG 13
+#define SLAVE_RBCPR_MX_CFG 14
+#define SLAVE_CRYPTO_0_CFG 15
+#define SLAVE_DCC_CFG 16
+#define SLAVE_CNOC_DDRSS 17
+#define SLAVE_DISPLAY_CFG 18
+#define SLAVE_DISPLAY_RT_THROTTLE_CFG 19
+#define SLAVE_DISPLAY_THROTTLE_CFG 20
+#define SLAVE_EMMC_CFG 21
+#define SLAVE_GLM 22
+#define SLAVE_GFX3D_CFG 23
+#define SLAVE_IMEM_CFG 24
+#define SLAVE_IPA_CFG 25
+#define SLAVE_CNOC_MNOC_CFG 26
+#define SLAVE_CNOC_MSS 27
+#define SLAVE_NPU_CFG 28
+#define SLAVE_NPU_DMA_BWMON_CFG 29
+#define SLAVE_NPU_PROC_BWMON_CFG 30
+#define SLAVE_PDM 31
+#define SLAVE_PIMEM_CFG 32
+#define SLAVE_PRNG 33
+#define SLAVE_QDSS_CFG 34
+#define SLAVE_QM_CFG 35
+#define SLAVE_QM_MPU_CFG 36
+#define SLAVE_QSPI_0 37
+#define SLAVE_QUP_0 38
+#define SLAVE_QUP_1 39
+#define SLAVE_SDCC_2 40
+#define SLAVE_SECURITY 41
+#define SLAVE_SNOC_CFG 42
+#define SLAVE_TCSR 43
+#define SLAVE_TLMM_WEST 44
+#define SLAVE_TLMM_NORTH 45
+#define SLAVE_TLMM_SOUTH 46
+#define SLAVE_UFS_MEM_CFG 47
+#define SLAVE_USB3 48
+#define SLAVE_VENUS_CFG 49
+#define SLAVE_VENUS_THROTTLE_CFG 50
+#define SLAVE_VSENSE_CTRL_CFG 51
+#define SLAVE_SERVICE_CNOC 52
+
+#define MASTER_CNOC_DC_NOC 0
+#define SLAVE_GEM_NOC_CFG 1
+#define SLAVE_LLCC_CFG 2
+
+#define MASTER_APPSS_PROC 0
+#define MASTER_SYS_TCU 1
+#define MASTER_GEM_NOC_CFG 2
+#define MASTER_COMPUTE_NOC 3
+#define MASTER_MNOC_HF_MEM_NOC 4
+#define MASTER_MNOC_SF_MEM_NOC 5
+#define MASTER_SNOC_GC_MEM_NOC 6
+#define MASTER_SNOC_SF_MEM_NOC 7
+#define MASTER_GFX3D 8
+#define SLAVE_MSS_PROC_MS_MPU_CFG 9
+#define SLAVE_GEM_NOC_SNOC 10
+#define SLAVE_LLCC 11
+#define SLAVE_SERVICE_GEM_NOC 12
+
+#define MASTER_IPA_CORE 0
+#define SLAVE_IPA_CORE 1
+
+#define MASTER_LLCC 0
+#define SLAVE_EBI1 1
+
+#define MASTER_CNOC_MNOC_CFG 0
+#define MASTER_CAMNOC_HF0 1
+#define MASTER_CAMNOC_HF1 2
+#define MASTER_CAMNOC_SF 3
+#define MASTER_MDP0 4
+#define MASTER_ROTATOR 5
+#define MASTER_VIDEO_P0 6
+#define MASTER_VIDEO_PROC 7
+#define SLAVE_MNOC_HF_MEM_NOC 8
+#define SLAVE_MNOC_SF_MEM_NOC 9
+#define SLAVE_SERVICE_MNOC 10
+
+#define MASTER_NPU_SYS 0
+#define MASTER_NPU_NOC_CFG 1
+#define SLAVE_NPU_CAL_DP0 2
+#define SLAVE_NPU_CP 3
+#define SLAVE_NPU_INT_DMA_BWMON_CFG 4
+#define SLAVE_NPU_DPM 5
+#define SLAVE_ISENSE_CFG 6
+#define SLAVE_NPU_LLM_CFG 7
+#define SLAVE_NPU_TCM 8
+#define SLAVE_NPU_COMPUTE_NOC 9
+#define SLAVE_SERVICE_NPU_NOC 10
+
+#define MASTER_QUP_CORE_0 0
+#define MASTER_QUP_CORE_1 1
+#define SLAVE_QUP_CORE_0 2
+#define SLAVE_QUP_CORE_1 3
+
+#define MASTER_SNOC_CFG 0
+#define MASTER_A1NOC_SNOC 1
+#define MASTER_A2NOC_SNOC 2
+#define MASTER_GEM_NOC_SNOC 3
+#define MASTER_PIMEM 4
+#define SLAVE_APPSS 5
+#define SLAVE_SNOC_CNOC 6
+#define SLAVE_SNOC_GEM_NOC_GC 7
+#define SLAVE_SNOC_GEM_NOC_SF 8
+#define SLAVE_IMEM 9
+#define SLAVE_PIMEM 10
+#define SLAVE_SERVICE_SNOC 11
+#define SLAVE_QDSS_STM 12
+#define SLAVE_TCU 13
+
+#endif
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver
2019-12-31 8:58 [V2, 0/3] Add SC7180 interconnect provider driver Odelu Kukatla
2019-12-31 8:58 ` [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings Odelu Kukatla
@ 2019-12-31 8:58 ` Odelu Kukatla
2020-01-05 6:55 ` Stephen Boyd
2019-12-31 8:58 ` [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes Odelu Kukatla
2 siblings, 1 reply; 12+ messages in thread
From: Odelu Kukatla @ 2019-12-31 8:58 UTC (permalink / raw)
To: georgi.djakov, daidavid1, bjorn.andersson, evgreen, Andy Gross,
linux-kernel, linux-arm-msm, linux-pm
Cc: sboyd, ilina, seansw, elder, linux-arm-msm-owner, Odelu Kukatla
Add driver for the Qualcomm interconnect buses found in SC7180 based
platforms. The topology consists of several NoCs that are controlled by
a remote processor that collects the aggregated bandwidth for each
master-slave pairs.
Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
---
drivers/interconnect/qcom/Kconfig | 10 +
drivers/interconnect/qcom/Makefile | 2 +
drivers/interconnect/qcom/bcm-voter.c | 1 +
drivers/interconnect/qcom/sc7180.c | 788 ++++++++++++++++++++++++++++++++++
4 files changed, 801 insertions(+)
create mode 100644 drivers/interconnect/qcom/sc7180.c
diff --git a/drivers/interconnect/qcom/Kconfig b/drivers/interconnect/qcom/Kconfig
index e5af199..a9bbbdf 100644
--- a/drivers/interconnect/qcom/Kconfig
+++ b/drivers/interconnect/qcom/Kconfig
@@ -23,6 +23,16 @@ config INTERCONNECT_QCOM_QCS404
This is a driver for the Qualcomm Network-on-Chip on qcs404-based
platforms.
+config INTERCONNECT_QCOM_SC7180
+ tristate "Qualcomm SC7180 interconnect driver"
+ depends on INTERCONNECT_QCOM
+ depends on (QCOM_RPMH && QCOM_COMMAND_DB && OF) || COMPILE_TEST
+ select INTERCONNECT_QCOM_RPMH
+ select INTERCONNECT_QCOM_BCM_VOTER
+ help
+ This is a driver for the Qualcomm Network-on-Chip on sc7180-based
+ platforms.
+
config INTERCONNECT_QCOM_SDM845
tristate "Qualcomm SDM845 interconnect driver"
depends on INTERCONNECT_QCOM
diff --git a/drivers/interconnect/qcom/Makefile b/drivers/interconnect/qcom/Makefile
index e921b13..55ec3c5 100644
--- a/drivers/interconnect/qcom/Makefile
+++ b/drivers/interconnect/qcom/Makefile
@@ -2,6 +2,7 @@
qnoc-msm8974-objs := msm8974.o
qnoc-qcs404-objs := qcs404.o
+qnoc-sc7180-objs := sc7180.o
qnoc-sdm845-objs := sdm845.o
icc-smd-rpm-objs := smd-rpm.o
icc-bcm-voter-objs := bcm-voter.o
@@ -13,5 +14,6 @@ obj-$(CONFIG_INTERCONNECT_QCOM_MSM8916) += qnoc-msm8916.o
obj-$(CONFIG_INTERCONNECT_QCOM_MSM8974) += qnoc-msm8974.o
obj-$(CONFIG_INTERCONNECT_QCOM_QCS404) += qnoc-qcs404.o
obj-$(CONFIG_INTERCONNECT_QCOM_RPMH) += icc-rpmh.o
+obj-$(CONFIG_INTERCONNECT_QCOM_SC7180) += qnoc-sc7180.o
obj-$(CONFIG_INTERCONNECT_QCOM_SDM845) += qnoc-sdm845.o
obj-$(CONFIG_INTERCONNECT_QCOM_SMD_RPM) += icc-smd-rpm.o
diff --git a/drivers/interconnect/qcom/bcm-voter.c b/drivers/interconnect/qcom/bcm-voter.c
index 7a8764e..d263b78 100644
--- a/drivers/interconnect/qcom/bcm-voter.c
+++ b/drivers/interconnect/qcom/bcm-voter.c
@@ -338,6 +338,7 @@ static int qcom_icc_bcm_voter_probe(struct platform_device *pdev)
}
static const struct of_device_id bcm_voter_of_match[] = {
+ { .compatible = "qcom,sc7180-bcm-voter" },
{ .compatible = "qcom,sdm845-bcm-voter" },
{ },
};
diff --git a/drivers/interconnect/qcom/sc7180.c b/drivers/interconnect/qcom/sc7180.c
new file mode 100644
index 0000000..4a398e0
--- /dev/null
+++ b/drivers/interconnect/qcom/sc7180.c
@@ -0,0 +1,788 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Copyright (c) 2019, The Linux Foundation. All rights reserved.
+ *
+ */
+
+#include <dt-bindings/interconnect/qcom,sc7180.h>
+#include <linux/device.h>
+#include <linux/interconnect.h>
+#include <linux/interconnect-provider.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+
+#include "icc-rpmh.h"
+#include "bcm-voter.h"
+
+enum {
+ SC7180_MASTER_APPSS_PROC,
+ SC7180_MASTER_SYS_TCU,
+ SC7180_MASTER_NPU_SYS,
+ SC7180_MASTER_IPA_CORE,
+ SC7180_MASTER_LLCC,
+ SC7180_MASTER_A1NOC_CFG,
+ SC7180_MASTER_A2NOC_CFG,
+ SC7180_MASTER_CNOC_DC_NOC,
+ SC7180_MASTER_GEM_NOC_CFG,
+ SC7180_MASTER_CNOC_MNOC_CFG,
+ SC7180_MASTER_NPU_NOC_CFG,
+ SC7180_MASTER_QDSS_BAM,
+ SC7180_MASTER_QSPI,
+ SC7180_MASTER_QUP_0,
+ SC7180_MASTER_QUP_1,
+ SC7180_MASTER_SNOC_CFG,
+ SC7180_MASTER_A1NOC_SNOC,
+ SC7180_MASTER_A2NOC_SNOC,
+ SC7180_MASTER_COMPUTE_NOC,
+ SC7180_MASTER_GEM_NOC_SNOC,
+ SC7180_MASTER_MNOC_HF_MEM_NOC,
+ SC7180_MASTER_MNOC_SF_MEM_NOC,
+ SC7180_MASTER_NPU,
+ SC7180_MASTER_SNOC_CNOC,
+ SC7180_MASTER_SNOC_GC_MEM_NOC,
+ SC7180_MASTER_SNOC_SF_MEM_NOC,
+ SC7180_MASTER_QUP_CORE_0,
+ SC7180_MASTER_QUP_CORE_1,
+ SC7180_MASTER_CAMNOC_HF0,
+ SC7180_MASTER_CAMNOC_HF1,
+ SC7180_MASTER_CAMNOC_HF0_UNCOMP,
+ SC7180_MASTER_CAMNOC_HF1_UNCOMP,
+ SC7180_MASTER_CAMNOC_SF,
+ SC7180_MASTER_CAMNOC_SF_UNCOMP,
+ SC7180_MASTER_CRYPTO,
+ SC7180_MASTER_GFX3D,
+ SC7180_MASTER_IPA,
+ SC7180_MASTER_MDP0,
+ SC7180_MASTER_NPU_PROC,
+ SC7180_MASTER_PIMEM,
+ SC7180_MASTER_ROTATOR,
+ SC7180_MASTER_VIDEO_P0,
+ SC7180_MASTER_VIDEO_PROC,
+ SC7180_MASTER_QDSS_DAP,
+ SC7180_MASTER_QDSS_ETR,
+ SC7180_MASTER_SDCC_2,
+ SC7180_MASTER_UFS_MEM,
+ SC7180_MASTER_USB3,
+ SC7180_MASTER_EMMC,
+ SC7180_SLAVE_EBI1,
+ SC7180_SLAVE_IPA_CORE,
+ SC7180_SLAVE_A1NOC_CFG,
+ SC7180_SLAVE_A2NOC_CFG,
+ SC7180_SLAVE_AHB2PHY_SOUTH,
+ SC7180_SLAVE_AHB2PHY_CENTER,
+ SC7180_SLAVE_AOP,
+ SC7180_SLAVE_AOSS,
+ SC7180_SLAVE_APPSS,
+ SC7180_SLAVE_BOOT_ROM,
+ SC7180_SLAVE_NPU_CAL_DP0,
+ SC7180_SLAVE_CAMERA_CFG,
+ SC7180_SLAVE_CAMERA_NRT_THROTTLE_CFG,
+ SC7180_SLAVE_CAMERA_RT_THROTTLE_CFG,
+ SC7180_SLAVE_CLK_CTL,
+ SC7180_SLAVE_NPU_CP,
+ SC7180_SLAVE_RBCPR_CX_CFG,
+ SC7180_SLAVE_RBCPR_MX_CFG,
+ SC7180_SLAVE_CRYPTO_0_CFG,
+ SC7180_SLAVE_DCC_CFG,
+ SC7180_SLAVE_CNOC_DDRSS,
+ SC7180_SLAVE_DISPLAY_CFG,
+ SC7180_SLAVE_DISPLAY_RT_THROTTLE_CFG,
+ SC7180_SLAVE_DISPLAY_THROTTLE_CFG,
+ SC7180_SLAVE_NPU_INT_DMA_BWMON_CFG,
+ SC7180_SLAVE_NPU_DPM,
+ SC7180_SLAVE_EMMC_CFG,
+ SC7180_SLAVE_GEM_NOC_CFG,
+ SC7180_SLAVE_GLM,
+ SC7180_SLAVE_GFX3D_CFG,
+ SC7180_SLAVE_IMEM_CFG,
+ SC7180_SLAVE_IPA_CFG,
+ SC7180_SLAVE_ISENSE_CFG,
+ SC7180_SLAVE_LLCC_CFG,
+ SC7180_SLAVE_NPU_LLM_CFG,
+ SC7180_SLAVE_MSS_PROC_MS_MPU_CFG,
+ SC7180_SLAVE_CNOC_MNOC_CFG,
+ SC7180_SLAVE_CNOC_MSS,
+ SC7180_SLAVE_NPU_CFG,
+ SC7180_SLAVE_NPU_DMA_BWMON_CFG,
+ SC7180_SLAVE_NPU_PROC_BWMON_CFG,
+ SC7180_SLAVE_PDM,
+ SC7180_SLAVE_PIMEM_CFG,
+ SC7180_SLAVE_PRNG,
+ SC7180_SLAVE_QDSS_CFG,
+ SC7180_SLAVE_QM_CFG,
+ SC7180_SLAVE_QM_MPU_CFG,
+ SC7180_SLAVE_QSPI_0,
+ SC7180_SLAVE_QUP_0,
+ SC7180_SLAVE_QUP_1,
+ SC7180_SLAVE_SDCC_2,
+ SC7180_SLAVE_SECURITY,
+ SC7180_SLAVE_SNOC_CFG,
+ SC7180_SLAVE_NPU_TCM,
+ SC7180_SLAVE_TCSR,
+ SC7180_SLAVE_TLMM_WEST,
+ SC7180_SLAVE_TLMM_NORTH,
+ SC7180_SLAVE_TLMM_SOUTH,
+ SC7180_SLAVE_UFS_MEM_CFG,
+ SC7180_SLAVE_USB3,
+ SC7180_SLAVE_VENUS_CFG,
+ SC7180_SLAVE_VENUS_THROTTLE_CFG,
+ SC7180_SLAVE_VSENSE_CTRL_CFG,
+ SC7180_SLAVE_A1NOC_SNOC,
+ SC7180_SLAVE_A2NOC_SNOC,
+ SC7180_SLAVE_CAMNOC_UNCOMP,
+ SC7180_SLAVE_CDSP_GEM_NOC,
+ SC7180_SLAVE_SNOC_CNOC,
+ SC7180_SLAVE_GEM_NOC_SNOC,
+ SC7180_SLAVE_SNOC_GEM_NOC_GC,
+ SC7180_SLAVE_SNOC_GEM_NOC_SF,
+ SC7180_SLAVE_LLCC,
+ SC7180_SLAVE_MNOC_HF_MEM_NOC,
+ SC7180_SLAVE_MNOC_SF_MEM_NOC,
+ SC7180_SLAVE_NPU_COMPUTE_NOC,
+ SC7180_SLAVE_QUP_CORE_0,
+ SC7180_SLAVE_QUP_CORE_1,
+ SC7180_SLAVE_IMEM,
+ SC7180_SLAVE_PIMEM,
+ SC7180_SLAVE_SERVICE_A1NOC,
+ SC7180_SLAVE_SERVICE_A2NOC,
+ SC7180_SLAVE_SERVICE_CNOC,
+ SC7180_SLAVE_SERVICE_GEM_NOC,
+ SC7180_SLAVE_SERVICE_MNOC,
+ SC7180_SLAVE_SERVICE_NPU_NOC,
+ SC7180_SLAVE_SERVICE_SNOC,
+ SC7180_SLAVE_QDSS_STM,
+ SC7180_SLAVE_TCU
+};
+
+DEFINE_QNODE(qhm_a1noc_cfg, SC7180_MASTER_A1NOC_CFG, 1, 4, 1, SC7180_SLAVE_SERVICE_A1NOC);
+DEFINE_QNODE(qhm_qspi, SC7180_MASTER_QSPI, 1, 4, 1, SC7180_SLAVE_A1NOC_SNOC);
+DEFINE_QNODE(qhm_qup_0, SC7180_MASTER_QUP_0, 1, 4, 1, SC7180_SLAVE_A1NOC_SNOC);
+DEFINE_QNODE(xm_sdc2, SC7180_MASTER_SDCC_2, 1, 8, 1, SC7180_SLAVE_A1NOC_SNOC);
+DEFINE_QNODE(xm_emmc, SC7180_MASTER_EMMC, 1, 8, 1, SC7180_SLAVE_A1NOC_SNOC);
+DEFINE_QNODE(xm_ufs_mem, SC7180_MASTER_UFS_MEM, 1, 8, 1, SC7180_SLAVE_A1NOC_SNOC);
+DEFINE_QNODE(qhm_a2noc_cfg, SC7180_MASTER_A2NOC_CFG, 1, 4, 1, SC7180_SLAVE_SERVICE_A2NOC);
+DEFINE_QNODE(qhm_qdss_bam, SC7180_MASTER_QDSS_BAM, 1, 4, 1, SC7180_SLAVE_A2NOC_SNOC);
+DEFINE_QNODE(qhm_qup_1, SC7180_MASTER_QUP_1, 1, 4, 1, SC7180_SLAVE_A2NOC_SNOC);
+DEFINE_QNODE(qxm_crypto, SC7180_MASTER_CRYPTO, 1, 8, 1, SC7180_SLAVE_A2NOC_SNOC);
+DEFINE_QNODE(qxm_ipa, SC7180_MASTER_IPA, 1, 8, 1, SC7180_SLAVE_A2NOC_SNOC);
+DEFINE_QNODE(xm_qdss_etr, SC7180_MASTER_QDSS_ETR, 1, 8, 1, SC7180_SLAVE_A2NOC_SNOC);
+DEFINE_QNODE(qhm_usb3, SC7180_MASTER_USB3, 1, 8, 1, SC7180_SLAVE_A2NOC_SNOC);
+DEFINE_QNODE(qxm_camnoc_hf0_uncomp, SC7180_MASTER_CAMNOC_HF0_UNCOMP, 1, 32, 1, SC7180_SLAVE_CAMNOC_UNCOMP);
+DEFINE_QNODE(qxm_camnoc_hf1_uncomp, SC7180_MASTER_CAMNOC_HF1_UNCOMP, 1, 32, 1, SC7180_SLAVE_CAMNOC_UNCOMP);
+DEFINE_QNODE(qxm_camnoc_sf_uncomp, SC7180_MASTER_CAMNOC_SF_UNCOMP, 1, 32, 1, SC7180_SLAVE_CAMNOC_UNCOMP);
+DEFINE_QNODE(qnm_npu, SC7180_MASTER_NPU, 2, 32, 1, SC7180_SLAVE_CDSP_GEM_NOC);
+DEFINE_QNODE(qxm_npu_dsp, SC7180_MASTER_NPU_PROC, 1, 8, 1, SC7180_SLAVE_CDSP_GEM_NOC);
+DEFINE_QNODE(qnm_snoc, SC7180_MASTER_SNOC_CNOC, 1, 8, 51, SC7180_SLAVE_A1NOC_CFG, SC7180_SLAVE_A2NOC_CFG, SC7180_SLAVE_AHB2PHY_SOUTH, SC7180_SLAVE_AHB2PHY_CENTER, SC7180_SLAVE_AOP, SC7180_SLAVE_AOSS, SC7180_SLAVE_BOOT_ROM, SC7180_SLAVE_CAMERA_CFG, SC7180_SLAVE_CAMERA_NRT_THROTTLE_CFG, SC7180_SLAVE_CAMERA_RT_THROTTLE_CFG, SC7180_SLAVE_CLK_CTL, SC7180_SLAVE_RBCPR_CX_CFG, SC7180_SLAVE_RBCPR_MX_CFG, SC7180_SLAVE_CRYPTO_0_CFG, SC7180_SLAVE_DCC_CFG, SC7180_SLAVE_CNOC_DDRSS, SC7180_SLAVE_DISPLAY_CFG, SC7180_SLAVE_DISPLAY_RT_THROTTLE_CFG, SC7180_SLAVE_DISPLAY_THROTTLE_CFG, SC7180_SLAVE_EMMC_CFG, SC7180_SLAVE_GLM,
+ SC7180_SLAVE_GFX3D_CFG, SC7180_SLAVE_IMEM_CFG, SC7180_SLAVE_IPA_CFG, SC7180_SLAVE_CNOC_MNOC_CFG, SC7180_SLAVE_CNOC_MSS, SC7180_SLAVE_NPU_CFG, SC7180_SLAVE_NPU_DMA_BWMON_CFG, SC7180_SLAVE_NPU_PROC_BWMON_CFG, SC7180_SLAVE_PDM, SC7180_SLAVE_PIMEM_CFG, SC7180_SLAVE_PRNG, SC7180_SLAVE_QDSS_CFG, SC7180_SLAVE_QM_CFG, SC7180_SLAVE_QM_MPU_CFG, SC7180_SLAVE_QSPI_0, SC7180_SLAVE_QUP_0, SC7180_SLAVE_QUP_1, SC7180_SLAVE_SDCC_2, SC7180_SLAVE_SECURITY, SC7180_SLAVE_SNOC_CFG, SC7180_SLAVE_TCSR, SC7180_SLAVE_TLMM_WEST, SC7180_SLAVE_TLMM_NORTH, SC7180_SLAVE_TLMM_SOUTH, SC7180_SLAVE_UFS_MEM_CFG, SC7180_SLAVE_USB3, SC7180_SLAVE_VENUS_CFG, SC7180_SLAVE_VENUS_THROTTLE_CFG, SC7180_SLAVE_VSENSE_CTRL_CFG, SC7180_SLAVE_SERVICE_CNOC);
+DEFINE_QNODE(xm_qdss_dap, SC7180_MASTER_QDSS_DAP, 1, 8, 51, SC7180_SLAVE_A1NOC_CFG, SC7180_SLAVE_A2NOC_CFG, SC7180_SLAVE_AHB2PHY_SOUTH, SC7180_SLAVE_AHB2PHY_CENTER, SC7180_SLAVE_AOP, SC7180_SLAVE_AOSS, SC7180_SLAVE_BOOT_ROM, SC7180_SLAVE_CAMERA_CFG, SC7180_SLAVE_CAMERA_NRT_THROTTLE_CFG, SC7180_SLAVE_CAMERA_RT_THROTTLE_CFG, SC7180_SLAVE_CLK_CTL, SC7180_SLAVE_RBCPR_CX_CFG, SC7180_SLAVE_RBCPR_MX_CFG, SC7180_SLAVE_CRYPTO_0_CFG, SC7180_SLAVE_DCC_CFG, SC7180_SLAVE_CNOC_DDRSS, SC7180_SLAVE_DISPLAY_CFG, SC7180_SLAVE_DISPLAY_RT_THROTTLE_CFG, SC7180_SLAVE_DISPLAY_THROTTLE_CFG, SC7180_SLAVE_EMMC_CFG, SC7180_SLAVE_GLM, SC7180_SLAVE_GFX3D_CFG, SC7180_SLAVE_IMEM_CFG, SC7180_SLAVE_IPA_CFG, SC7180_SLAVE_CNOC_MNOC_CFG, SC7180_SLAVE_CNOC_MSS, SC7180_SLAVE_NPU_CFG, SC7180_SLAVE_NPU_DMA_BWMON_CFG,
+SC7180_SLAVE_NPU_PROC_BWMON_CFG, SC7180_SLAVE_PDM, SC7180_SLAVE_PIMEM_CFG, SC7180_SLAVE_PRNG, SC7180_SLAVE_QDSS_CFG, SC7180_SLAVE_QM_CFG, SC7180_SLAVE_QM_MPU_CFG, SC7180_SLAVE_QSPI_0, SC7180_SLAVE_QUP_0, SC7180_SLAVE_QUP_1, SC7180_SLAVE_SDCC_2, SC7180_SLAVE_SECURITY, SC7180_SLAVE_SNOC_CFG, SC7180_SLAVE_TCSR, SC7180_SLAVE_TLMM_WEST, SC7180_SLAVE_TLMM_NORTH, SC7180_SLAVE_TLMM_SOUTH, SC7180_SLAVE_UFS_MEM_CFG, SC7180_SLAVE_USB3, SC7180_SLAVE_VENUS_CFG, SC7180_SLAVE_VENUS_THROTTLE_CFG, SC7180_SLAVE_VSENSE_CTRL_CFG, SC7180_SLAVE_SERVICE_CNOC);
+DEFINE_QNODE(qhm_cnoc_dc_noc, SC7180_MASTER_CNOC_DC_NOC, 1, 4, 2, SC7180_SLAVE_GEM_NOC_CFG, SC7180_SLAVE_LLCC_CFG);
+DEFINE_QNODE(acm_apps0, SC7180_MASTER_APPSS_PROC, 1, 16, 2, SC7180_SLAVE_GEM_NOC_SNOC, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(acm_sys_tcu, SC7180_MASTER_SYS_TCU, 1, 8, 2, SC7180_SLAVE_GEM_NOC_SNOC, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(qhm_gemnoc_cfg, SC7180_MASTER_GEM_NOC_CFG, 1, 4, 2, SC7180_SLAVE_MSS_PROC_MS_MPU_CFG, SC7180_SLAVE_SERVICE_GEM_NOC);
+DEFINE_QNODE(qnm_cmpnoc, SC7180_MASTER_COMPUTE_NOC, 1, 32, 2, SC7180_SLAVE_GEM_NOC_SNOC, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(qnm_mnoc_hf, SC7180_MASTER_MNOC_HF_MEM_NOC, 1, 32, 1, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(qnm_mnoc_sf, SC7180_MASTER_MNOC_SF_MEM_NOC, 1, 32, 2, SC7180_SLAVE_GEM_NOC_SNOC, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(qnm_snoc_gc, SC7180_MASTER_SNOC_GC_MEM_NOC, 1, 8, 1, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(qnm_snoc_sf, SC7180_MASTER_SNOC_SF_MEM_NOC, 1, 16, 1, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(qxm_gpu, SC7180_MASTER_GFX3D, 2, 32, 2, SC7180_SLAVE_GEM_NOC_SNOC, SC7180_SLAVE_LLCC);
+DEFINE_QNODE(ipa_core_master, SC7180_MASTER_IPA_CORE, 1, 8, 1, SC7180_SLAVE_IPA_CORE);
+DEFINE_QNODE(llcc_mc, SC7180_MASTER_LLCC, 2, 4, 1, SC7180_SLAVE_EBI1);
+DEFINE_QNODE(qhm_mnoc_cfg, SC7180_MASTER_CNOC_MNOC_CFG, 1, 4, 1, SC7180_SLAVE_SERVICE_MNOC);
+DEFINE_QNODE(qxm_camnoc_hf0, SC7180_MASTER_CAMNOC_HF0, 2, 32, 1, SC7180_SLAVE_MNOC_HF_MEM_NOC);
+DEFINE_QNODE(qxm_camnoc_hf1, SC7180_MASTER_CAMNOC_HF1, 2, 32, 1, SC7180_SLAVE_MNOC_HF_MEM_NOC);
+DEFINE_QNODE(qxm_camnoc_sf, SC7180_MASTER_CAMNOC_SF, 1, 32, 1, SC7180_SLAVE_MNOC_SF_MEM_NOC);
+DEFINE_QNODE(qxm_mdp0, SC7180_MASTER_MDP0, 1, 32, 1, SC7180_SLAVE_MNOC_HF_MEM_NOC);
+DEFINE_QNODE(qxm_rot, SC7180_MASTER_ROTATOR, 1, 16, 1, SC7180_SLAVE_MNOC_SF_MEM_NOC);
+DEFINE_QNODE(qxm_venus0, SC7180_MASTER_VIDEO_P0, 1, 32, 1, SC7180_SLAVE_MNOC_SF_MEM_NOC);
+DEFINE_QNODE(qxm_venus_arm9, SC7180_MASTER_VIDEO_PROC, 1, 8, 1, SC7180_SLAVE_MNOC_SF_MEM_NOC);
+DEFINE_QNODE(amm_npu_sys, SC7180_MASTER_NPU_SYS, 2, 32, 1, SC7180_SLAVE_NPU_COMPUTE_NOC);
+DEFINE_QNODE(qhm_npu_cfg, SC7180_MASTER_NPU_NOC_CFG, 1, 4, 8, SC7180_SLAVE_NPU_CAL_DP0, SC7180_SLAVE_NPU_CP, SC7180_SLAVE_NPU_INT_DMA_BWMON_CFG, SC7180_SLAVE_NPU_DPM, SC7180_SLAVE_ISENSE_CFG, SC7180_SLAVE_NPU_LLM_CFG, SC7180_SLAVE_NPU_TCM, SC7180_SLAVE_SERVICE_NPU_NOC);
+DEFINE_QNODE(qup_core_master_1, SC7180_MASTER_QUP_CORE_0, 1, 4, 1, SC7180_SLAVE_QUP_CORE_0);
+DEFINE_QNODE(qup_core_master_2, SC7180_MASTER_QUP_CORE_1, 1, 4, 1, SC7180_SLAVE_QUP_CORE_1);
+DEFINE_QNODE(qhm_snoc_cfg, SC7180_MASTER_SNOC_CFG, 1, 4, 1, SC7180_SLAVE_SERVICE_SNOC);
+DEFINE_QNODE(qnm_aggre1_noc, SC7180_MASTER_A1NOC_SNOC, 1, 16, 6, SC7180_SLAVE_APPSS, SC7180_SLAVE_SNOC_CNOC, SC7180_SLAVE_SNOC_GEM_NOC_SF, SC7180_SLAVE_IMEM, SC7180_SLAVE_PIMEM, SC7180_SLAVE_QDSS_STM);
+DEFINE_QNODE(qnm_aggre2_noc, SC7180_MASTER_A2NOC_SNOC, 1, 16, 7, SC7180_SLAVE_APPSS, SC7180_SLAVE_SNOC_CNOC, SC7180_SLAVE_SNOC_GEM_NOC_SF, SC7180_SLAVE_IMEM, SC7180_SLAVE_PIMEM, SC7180_SLAVE_QDSS_STM, SC7180_SLAVE_TCU);
+DEFINE_QNODE(qnm_gemnoc, SC7180_MASTER_GEM_NOC_SNOC, 1, 8, 6, SC7180_SLAVE_APPSS, SC7180_SLAVE_SNOC_CNOC, SC7180_SLAVE_IMEM, SC7180_SLAVE_PIMEM, SC7180_SLAVE_QDSS_STM, SC7180_SLAVE_TCU);
+DEFINE_QNODE(qxm_pimem, SC7180_MASTER_PIMEM, 1, 8, 2, SC7180_SLAVE_SNOC_GEM_NOC_GC, SC7180_SLAVE_IMEM);
+DEFINE_QNODE(qns_a1noc_snoc, SC7180_SLAVE_A1NOC_SNOC, 1, 16, 1, SC7180_MASTER_A1NOC_SNOC);
+DEFINE_QNODE(srvc_aggre1_noc, SC7180_SLAVE_SERVICE_A1NOC, 1, 4, 0);
+DEFINE_QNODE(qns_a2noc_snoc, SC7180_SLAVE_A2NOC_SNOC, 1, 16, 1, SC7180_MASTER_A2NOC_SNOC);
+DEFINE_QNODE(srvc_aggre2_noc, SC7180_SLAVE_SERVICE_A2NOC, 1, 4, 0);
+DEFINE_QNODE(qns_camnoc_uncomp, SC7180_SLAVE_CAMNOC_UNCOMP, 1, 32, 0);
+DEFINE_QNODE(qns_cdsp_gemnoc, SC7180_SLAVE_CDSP_GEM_NOC, 1, 32, 1, SC7180_MASTER_COMPUTE_NOC);
+DEFINE_QNODE(qhs_a1_noc_cfg, SC7180_SLAVE_A1NOC_CFG, 1, 4, 1, SC7180_MASTER_A1NOC_CFG);
+DEFINE_QNODE(qhs_a2_noc_cfg, SC7180_SLAVE_A2NOC_CFG, 1, 4, 1, SC7180_MASTER_A2NOC_CFG);
+DEFINE_QNODE(qhs_ahb2phy0, SC7180_SLAVE_AHB2PHY_SOUTH, 1, 4, 0);
+DEFINE_QNODE(qhs_ahb2phy2, SC7180_SLAVE_AHB2PHY_CENTER, 1, 4, 0);
+DEFINE_QNODE(qhs_aop, SC7180_SLAVE_AOP, 1, 4, 0);
+DEFINE_QNODE(qhs_aoss, SC7180_SLAVE_AOSS, 1, 4, 0);
+DEFINE_QNODE(qhs_boot_rom, SC7180_SLAVE_BOOT_ROM, 1, 4, 0);
+DEFINE_QNODE(qhs_camera_cfg, SC7180_SLAVE_CAMERA_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_camera_nrt_throttle_cfg, SC7180_SLAVE_CAMERA_NRT_THROTTLE_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_camera_rt_throttle_cfg, SC7180_SLAVE_CAMERA_RT_THROTTLE_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_clk_ctl, SC7180_SLAVE_CLK_CTL, 1, 4, 0);
+DEFINE_QNODE(qhs_cpr_cx, SC7180_SLAVE_RBCPR_CX_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_cpr_mx, SC7180_SLAVE_RBCPR_MX_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_crypto0_cfg, SC7180_SLAVE_CRYPTO_0_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_dcc_cfg, SC7180_SLAVE_DCC_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_ddrss_cfg, SC7180_SLAVE_CNOC_DDRSS, 1, 4, 1, SC7180_MASTER_CNOC_DC_NOC);
+DEFINE_QNODE(qhs_display_cfg, SC7180_SLAVE_DISPLAY_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_display_rt_throttle_cfg, SC7180_SLAVE_DISPLAY_RT_THROTTLE_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_display_throttle_cfg, SC7180_SLAVE_DISPLAY_THROTTLE_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_emmc_cfg, SC7180_SLAVE_EMMC_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_glm, SC7180_SLAVE_GLM, 1, 4, 0);
+DEFINE_QNODE(qhs_gpuss_cfg, SC7180_SLAVE_GFX3D_CFG, 1, 8, 0);
+DEFINE_QNODE(qhs_imem_cfg, SC7180_SLAVE_IMEM_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_ipa, SC7180_SLAVE_IPA_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_mnoc_cfg, SC7180_SLAVE_CNOC_MNOC_CFG, 1, 4, 1, SC7180_MASTER_CNOC_MNOC_CFG);
+DEFINE_QNODE(qhs_mss_cfg, SC7180_SLAVE_CNOC_MSS, 1, 4, 0);
+DEFINE_QNODE(qhs_npu_cfg, SC7180_SLAVE_NPU_CFG, 1, 4, 1, SC7180_MASTER_NPU_NOC_CFG);
+DEFINE_QNODE(qhs_npu_dma_throttle_cfg, SC7180_SLAVE_NPU_DMA_BWMON_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_npu_dsp_throttle_cfg, SC7180_SLAVE_NPU_PROC_BWMON_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_pdm, SC7180_SLAVE_PDM, 1, 4, 0);
+DEFINE_QNODE(qhs_pimem_cfg, SC7180_SLAVE_PIMEM_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_prng, SC7180_SLAVE_PRNG, 1, 4, 0);
+DEFINE_QNODE(qhs_qdss_cfg, SC7180_SLAVE_QDSS_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_qm_cfg, SC7180_SLAVE_QM_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_qm_mpu_cfg, SC7180_SLAVE_QM_MPU_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_qspi, SC7180_SLAVE_QSPI_0, 1, 4, 0);
+DEFINE_QNODE(qhs_qup0, SC7180_SLAVE_QUP_0, 1, 4, 0);
+DEFINE_QNODE(qhs_qup1, SC7180_SLAVE_QUP_1, 1, 4, 0);
+DEFINE_QNODE(qhs_sdc2, SC7180_SLAVE_SDCC_2, 1, 4, 0);
+DEFINE_QNODE(qhs_security, SC7180_SLAVE_SECURITY, 1, 4, 0);
+DEFINE_QNODE(qhs_snoc_cfg, SC7180_SLAVE_SNOC_CFG, 1, 4, 1, SC7180_MASTER_SNOC_CFG);
+DEFINE_QNODE(qhs_tcsr, SC7180_SLAVE_TCSR, 1, 4, 0);
+DEFINE_QNODE(qhs_tlmm_1, SC7180_SLAVE_TLMM_WEST, 1, 4, 0);
+DEFINE_QNODE(qhs_tlmm_2, SC7180_SLAVE_TLMM_NORTH, 1, 4, 0);
+DEFINE_QNODE(qhs_tlmm_3, SC7180_SLAVE_TLMM_SOUTH, 1, 4, 0);
+DEFINE_QNODE(qhs_ufs_mem_cfg, SC7180_SLAVE_UFS_MEM_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_usb3, SC7180_SLAVE_USB3, 1, 4, 0);
+DEFINE_QNODE(qhs_venus_cfg, SC7180_SLAVE_VENUS_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_venus_throttle_cfg, SC7180_SLAVE_VENUS_THROTTLE_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_vsense_ctrl_cfg, SC7180_SLAVE_VSENSE_CTRL_CFG, 1, 4, 0);
+DEFINE_QNODE(srvc_cnoc, SC7180_SLAVE_SERVICE_CNOC, 1, 4, 0);
+DEFINE_QNODE(qhs_gemnoc, SC7180_SLAVE_GEM_NOC_CFG, 1, 4, 1, SC7180_MASTER_GEM_NOC_CFG);
+DEFINE_QNODE(qhs_llcc, SC7180_SLAVE_LLCC_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_mdsp_ms_mpu_cfg, SC7180_SLAVE_MSS_PROC_MS_MPU_CFG, 1, 4, 0);
+DEFINE_QNODE(qns_gem_noc_snoc, SC7180_SLAVE_GEM_NOC_SNOC, 1, 8, 1, SC7180_MASTER_GEM_NOC_SNOC);
+DEFINE_QNODE(qns_llcc, SC7180_SLAVE_LLCC, 1, 16, 1, SC7180_MASTER_LLCC);
+DEFINE_QNODE(srvc_gemnoc, SC7180_SLAVE_SERVICE_GEM_NOC, 1, 4, 0);
+DEFINE_QNODE(ipa_core_slave, SC7180_SLAVE_IPA_CORE, 1, 8, 0);
+DEFINE_QNODE(ebi, SC7180_SLAVE_EBI1, 2, 4, 0);
+DEFINE_QNODE(qns_mem_noc_hf, SC7180_SLAVE_MNOC_HF_MEM_NOC, 1, 32, 1, SC7180_MASTER_MNOC_HF_MEM_NOC);
+DEFINE_QNODE(qns_mem_noc_sf, SC7180_SLAVE_MNOC_SF_MEM_NOC, 1, 32, 1, SC7180_MASTER_MNOC_SF_MEM_NOC);
+DEFINE_QNODE(srvc_mnoc, SC7180_SLAVE_SERVICE_MNOC, 1, 4, 0);
+DEFINE_QNODE(qhs_cal_dp0, SC7180_SLAVE_NPU_CAL_DP0, 1, 4, 0);
+DEFINE_QNODE(qhs_cp, SC7180_SLAVE_NPU_CP, 1, 4, 0);
+DEFINE_QNODE(qhs_dma_bwmon, SC7180_SLAVE_NPU_INT_DMA_BWMON_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_dpm, SC7180_SLAVE_NPU_DPM, 1, 4, 0);
+DEFINE_QNODE(qhs_isense, SC7180_SLAVE_ISENSE_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_llm, SC7180_SLAVE_NPU_LLM_CFG, 1, 4, 0);
+DEFINE_QNODE(qhs_tcm, SC7180_SLAVE_NPU_TCM, 1, 4, 0);
+DEFINE_QNODE(qns_npu_sys, SC7180_SLAVE_NPU_COMPUTE_NOC, 2, 32, 0);
+DEFINE_QNODE(srvc_noc, SC7180_SLAVE_SERVICE_NPU_NOC, 1, 4, 0);
+DEFINE_QNODE(qup_core_slave_1, SC7180_SLAVE_QUP_CORE_0, 1, 4, 0);
+DEFINE_QNODE(qup_core_slave_2, SC7180_SLAVE_QUP_CORE_1, 1, 4, 0);
+DEFINE_QNODE(qhs_apss, SC7180_SLAVE_APPSS, 1, 8, 0);
+DEFINE_QNODE(qns_cnoc, SC7180_SLAVE_SNOC_CNOC, 1, 8, 1, SC7180_MASTER_SNOC_CNOC);
+DEFINE_QNODE(qns_gemnoc_gc, SC7180_SLAVE_SNOC_GEM_NOC_GC, 1, 8, 1, SC7180_MASTER_SNOC_GC_MEM_NOC);
+DEFINE_QNODE(qns_gemnoc_sf, SC7180_SLAVE_SNOC_GEM_NOC_SF, 1, 16, 1, SC7180_MASTER_SNOC_SF_MEM_NOC);
+DEFINE_QNODE(qxs_imem, SC7180_SLAVE_IMEM, 1, 8, 0);
+DEFINE_QNODE(qxs_pimem, SC7180_SLAVE_PIMEM, 1, 8, 0);
+DEFINE_QNODE(srvc_snoc, SC7180_SLAVE_SERVICE_SNOC, 1, 4, 0);
+DEFINE_QNODE(xs_qdss_stm, SC7180_SLAVE_QDSS_STM, 1, 4, 0);
+DEFINE_QNODE(xs_sys_tcu_cfg, SC7180_SLAVE_TCU, 1, 8, 0);
+
+DEFINE_QBCM(bcm_acv, "ACV", false, 1, &ebi);
+DEFINE_QBCM(bcm_mc0, "MC0", true, 1, &ebi);
+DEFINE_QBCM(bcm_sh0, "SH0", true, 1, &qns_llcc);
+DEFINE_QBCM(bcm_mm0, "MM0", false, 1, &qns_mem_noc_hf);
+DEFINE_QBCM(bcm_ce0, "CE0", false, 1, &qxm_crypto);
+DEFINE_QBCM(bcm_ip0, "IP0", false, 1, &ipa_core_slave);
+DEFINE_QBCM(bcm_cn0, "CN0", true, 48, &qnm_snoc, &xm_qdss_dap, &qhs_a1_noc_cfg, &qhs_a2_noc_cfg, &qhs_ahb2phy0, &qhs_aop, &qhs_aoss, &qhs_boot_rom, &qhs_camera_cfg, &qhs_camera_nrt_throttle_cfg, &qhs_camera_rt_throttle_cfg, &qhs_clk_ctl, &qhs_cpr_cx, &qhs_cpr_mx, &qhs_crypto0_cfg, &qhs_dcc_cfg, &qhs_ddrss_cfg, &qhs_display_cfg, &qhs_display_rt_throttle_cfg, &qhs_display_throttle_cfg, &qhs_glm, &qhs_gpuss_cfg, &qhs_imem_cfg, &qhs_ipa, &qhs_mnoc_cfg, &qhs_mss_cfg, &qhs_npu_cfg, &qhs_npu_dma_throttle_cfg, &qhs_npu_dsp_throttle_cfg, &qhs_pimem_cfg, &qhs_prng, &qhs_qdss_cfg, &qhs_qm_cfg, &qhs_qm_mpu_cfg, &qhs_qup0, &qhs_qup1, &qhs_security, &qhs_snoc_cfg, &qhs_tcsr, &qhs_tlmm_1, &qhs_tlmm_2, &qhs_tlmm_3, &qhs_ufs_mem_cfg, &qhs_usb3, &qhs_venus_cfg, &qhs_venus_throttle_cfg, &qhs_vsense_ctrl_cfg, &srvc_cnoc);
+DEFINE_QBCM(bcm_mm1, "MM1", false, 8, &qxm_camnoc_hf0_uncomp, &qxm_camnoc_hf1_uncomp, &qxm_camnoc_sf_uncomp, &qhm_mnoc_cfg, &qxm_mdp0, &qxm_rot, &qxm_venus0, &qxm_venus_arm9);
+DEFINE_QBCM(bcm_sh2, "SH2", false, 1, &acm_sys_tcu);
+DEFINE_QBCM(bcm_mm2, "MM2", false, 1, &qns_mem_noc_sf);
+DEFINE_QBCM(bcm_qup0, "QUP0", false, 2, &qup_core_master_1, &qup_core_master_2);
+DEFINE_QBCM(bcm_sh3, "SH3", false, 1, &qnm_cmpnoc);
+DEFINE_QBCM(bcm_sh4, "SH4", false, 1, &acm_apps0);
+DEFINE_QBCM(bcm_sn0, "SN0", true, 1, &qns_gemnoc_sf);
+DEFINE_QBCM(bcm_co0, "CO0", false, 1, &qns_cdsp_gemnoc);
+DEFINE_QBCM(bcm_sn1, "SN1", false, 1, &qxs_imem);
+DEFINE_QBCM(bcm_cn1, "CN1", false, 8, &qhm_qspi, &xm_sdc2, &xm_emmc, &qhs_ahb2phy2, &qhs_emmc_cfg, &qhs_pdm, &qhs_qspi, &qhs_sdc2);
+DEFINE_QBCM(bcm_sn2, "SN2", false, 2, &qxm_pimem, &qns_gemnoc_gc);
+DEFINE_QBCM(bcm_co2, "CO2", false, 1, &qnm_npu);
+DEFINE_QBCM(bcm_sn3, "SN3", false, 1, &qxs_pimem);
+DEFINE_QBCM(bcm_co3, "CO3", false, 1, &qxm_npu_dsp);
+DEFINE_QBCM(bcm_sn4, "SN4", false, 1, &xs_qdss_stm);
+DEFINE_QBCM(bcm_sn7, "SN7", false, 1, &qnm_aggre1_noc);
+DEFINE_QBCM(bcm_sn9, "SN9", false, 1, &qnm_aggre2_noc);
+DEFINE_QBCM(bcm_sn12, "SN12", false, 1, &qnm_gemnoc);
+
+static struct qcom_icc_bcm *aggre1_noc_bcms[] = {
+ &bcm_cn1,
+};
+
+static struct qcom_icc_node *aggre1_noc_nodes[] = {
+ [MASTER_A1NOC_CFG] = &qhm_a1noc_cfg,
+ [MASTER_QSPI] = &qhm_qspi,
+ [MASTER_QUP_0] = &qhm_qup_0,
+ [MASTER_SDCC_2] = &xm_sdc2,
+ [MASTER_EMMC] = &xm_emmc,
+ [MASTER_UFS_MEM] = &xm_ufs_mem,
+ [SLAVE_A1NOC_SNOC] = &qns_a1noc_snoc,
+ [SLAVE_SERVICE_A1NOC] = &srvc_aggre1_noc,
+};
+
+static struct qcom_icc_desc sc7180_aggre1_noc = {
+ .nodes = aggre1_noc_nodes,
+ .num_nodes = ARRAY_SIZE(aggre1_noc_nodes),
+ .bcms = aggre1_noc_bcms,
+ .num_bcms = ARRAY_SIZE(aggre1_noc_bcms),
+};
+
+static struct qcom_icc_bcm *aggre2_noc_bcms[] = {
+ &bcm_ce0,
+};
+
+static struct qcom_icc_node *aggre2_noc_nodes[] = {
+ [MASTER_A2NOC_CFG] = &qhm_a2noc_cfg,
+ [MASTER_QDSS_BAM] = &qhm_qdss_bam,
+ [MASTER_QUP_1] = &qhm_qup_1,
+ [MASTER_USB3] = &qhm_usb3,
+ [MASTER_CRYPTO] = &qxm_crypto,
+ [MASTER_IPA] = &qxm_ipa,
+ [MASTER_QDSS_ETR] = &xm_qdss_etr,
+ [SLAVE_A2NOC_SNOC] = &qns_a2noc_snoc,
+ [SLAVE_SERVICE_A2NOC] = &srvc_aggre2_noc,
+};
+
+static struct qcom_icc_desc sc7180_aggre2_noc = {
+ .nodes = aggre2_noc_nodes,
+ .num_nodes = ARRAY_SIZE(aggre2_noc_nodes),
+ .bcms = aggre2_noc_bcms,
+ .num_bcms = ARRAY_SIZE(aggre2_noc_bcms),
+};
+
+static struct qcom_icc_bcm *camnoc_virt_bcms[] = {
+ &bcm_mm1,
+};
+
+static struct qcom_icc_node *camnoc_virt_nodes[] = {
+ [MASTER_CAMNOC_HF0_UNCOMP] = &qxm_camnoc_hf0_uncomp,
+ [MASTER_CAMNOC_HF1_UNCOMP] = &qxm_camnoc_hf1_uncomp,
+ [MASTER_CAMNOC_SF_UNCOMP] = &qxm_camnoc_sf_uncomp,
+ [SLAVE_CAMNOC_UNCOMP] = &qns_camnoc_uncomp,
+};
+
+static struct qcom_icc_desc sc7180_camnoc_virt = {
+ .nodes = camnoc_virt_nodes,
+ .num_nodes = ARRAY_SIZE(camnoc_virt_nodes),
+ .bcms = camnoc_virt_bcms,
+ .num_bcms = ARRAY_SIZE(camnoc_virt_bcms),
+};
+
+static struct qcom_icc_bcm *compute_noc_bcms[] = {
+ &bcm_co0,
+ &bcm_co2,
+ &bcm_co3,
+};
+
+static struct qcom_icc_node *compute_noc_nodes[] = {
+ [MASTER_NPU] = &qnm_npu,
+ [MASTER_NPU_PROC] = &qxm_npu_dsp,
+ [SLAVE_CDSP_GEM_NOC] = &qns_cdsp_gemnoc,
+};
+
+static struct qcom_icc_desc sc7180_compute_noc = {
+ .nodes = compute_noc_nodes,
+ .num_nodes = ARRAY_SIZE(compute_noc_nodes),
+ .bcms = compute_noc_bcms,
+ .num_bcms = ARRAY_SIZE(compute_noc_bcms),
+};
+
+static struct qcom_icc_bcm *config_noc_bcms[] = {
+ &bcm_cn0,
+ &bcm_cn1,
+};
+
+static struct qcom_icc_node *config_noc_nodes[] = {
+ [MASTER_SNOC_CNOC] = &qnm_snoc,
+ [MASTER_QDSS_DAP] = &xm_qdss_dap,
+ [SLAVE_A1NOC_CFG] = &qhs_a1_noc_cfg,
+ [SLAVE_A2NOC_CFG] = &qhs_a2_noc_cfg,
+ [SLAVE_AHB2PHY_SOUTH] = &qhs_ahb2phy0,
+ [SLAVE_AHB2PHY_CENTER] = &qhs_ahb2phy2,
+ [SLAVE_AOP] = &qhs_aop,
+ [SLAVE_AOSS] = &qhs_aoss,
+ [SLAVE_BOOT_ROM] = &qhs_boot_rom,
+ [SLAVE_CAMERA_CFG] = &qhs_camera_cfg,
+ [SLAVE_CAMERA_NRT_THROTTLE_CFG] = &qhs_camera_nrt_throttle_cfg,
+ [SLAVE_CAMERA_RT_THROTTLE_CFG] = &qhs_camera_rt_throttle_cfg,
+ [SLAVE_CLK_CTL] = &qhs_clk_ctl,
+ [SLAVE_RBCPR_CX_CFG] = &qhs_cpr_cx,
+ [SLAVE_RBCPR_MX_CFG] = &qhs_cpr_mx,
+ [SLAVE_CRYPTO_0_CFG] = &qhs_crypto0_cfg,
+ [SLAVE_DCC_CFG] = &qhs_dcc_cfg,
+ [SLAVE_CNOC_DDRSS] = &qhs_ddrss_cfg,
+ [SLAVE_DISPLAY_CFG] = &qhs_display_cfg,
+ [SLAVE_DISPLAY_RT_THROTTLE_CFG] = &qhs_display_rt_throttle_cfg,
+ [SLAVE_DISPLAY_THROTTLE_CFG] = &qhs_display_throttle_cfg,
+ [SLAVE_EMMC_CFG] = &qhs_emmc_cfg,
+ [SLAVE_GLM] = &qhs_glm,
+ [SLAVE_GFX3D_CFG] = &qhs_gpuss_cfg,
+ [SLAVE_IMEM_CFG] = &qhs_imem_cfg,
+ [SLAVE_IPA_CFG] = &qhs_ipa,
+ [SLAVE_CNOC_MNOC_CFG] = &qhs_mnoc_cfg,
+ [SLAVE_CNOC_MSS] = &qhs_mss_cfg,
+ [SLAVE_NPU_CFG] = &qhs_npu_cfg,
+ [SLAVE_NPU_DMA_BWMON_CFG] = &qhs_npu_dma_throttle_cfg,
+ [SLAVE_NPU_PROC_BWMON_CFG] = &qhs_npu_dsp_throttle_cfg,
+ [SLAVE_PDM] = &qhs_pdm,
+ [SLAVE_PIMEM_CFG] = &qhs_pimem_cfg,
+ [SLAVE_PRNG] = &qhs_prng,
+ [SLAVE_QDSS_CFG] = &qhs_qdss_cfg,
+ [SLAVE_QM_CFG] = &qhs_qm_cfg,
+ [SLAVE_QM_MPU_CFG] = &qhs_qm_mpu_cfg,
+ [SLAVE_QSPI_0] = &qhs_qspi,
+ [SLAVE_QUP_0] = &qhs_qup0,
+ [SLAVE_QUP_1] = &qhs_qup1,
+ [SLAVE_SDCC_2] = &qhs_sdc2,
+ [SLAVE_SECURITY] = &qhs_security,
+ [SLAVE_SNOC_CFG] = &qhs_snoc_cfg,
+ [SLAVE_TCSR] = &qhs_tcsr,
+ [SLAVE_TLMM_WEST] = &qhs_tlmm_1,
+ [SLAVE_TLMM_NORTH] = &qhs_tlmm_2,
+ [SLAVE_TLMM_SOUTH] = &qhs_tlmm_3,
+ [SLAVE_UFS_MEM_CFG] = &qhs_ufs_mem_cfg,
+ [SLAVE_USB3] = &qhs_usb3,
+ [SLAVE_VENUS_CFG] = &qhs_venus_cfg,
+ [SLAVE_VENUS_THROTTLE_CFG] = &qhs_venus_throttle_cfg,
+ [SLAVE_VSENSE_CTRL_CFG] = &qhs_vsense_ctrl_cfg,
+ [SLAVE_SERVICE_CNOC] = &srvc_cnoc,
+};
+
+static struct qcom_icc_desc sc7180_config_noc = {
+ .nodes = config_noc_nodes,
+ .num_nodes = ARRAY_SIZE(config_noc_nodes),
+ .bcms = config_noc_bcms,
+ .num_bcms = ARRAY_SIZE(config_noc_bcms),
+};
+
+static struct qcom_icc_node *dc_noc_nodes[] = {
+ [MASTER_CNOC_DC_NOC] = &qhm_cnoc_dc_noc,
+ [SLAVE_GEM_NOC_CFG] = &qhs_gemnoc,
+ [SLAVE_LLCC_CFG] = &qhs_llcc,
+};
+
+static struct qcom_icc_desc sc7180_dc_noc = {
+ .nodes = dc_noc_nodes,
+ .num_nodes = ARRAY_SIZE(dc_noc_nodes),
+};
+
+static struct qcom_icc_bcm *gem_noc_bcms[] = {
+ &bcm_sh0,
+ &bcm_sh2,
+ &bcm_sh3,
+ &bcm_sh4,
+};
+
+static struct qcom_icc_node *gem_noc_nodes[] = {
+ [MASTER_APPSS_PROC] = &acm_apps0,
+ [MASTER_SYS_TCU] = &acm_sys_tcu,
+ [MASTER_GEM_NOC_CFG] = &qhm_gemnoc_cfg,
+ [MASTER_COMPUTE_NOC] = &qnm_cmpnoc,
+ [MASTER_MNOC_HF_MEM_NOC] = &qnm_mnoc_hf,
+ [MASTER_MNOC_SF_MEM_NOC] = &qnm_mnoc_sf,
+ [MASTER_SNOC_GC_MEM_NOC] = &qnm_snoc_gc,
+ [MASTER_SNOC_SF_MEM_NOC] = &qnm_snoc_sf,
+ [MASTER_GFX3D] = &qxm_gpu,
+ [SLAVE_MSS_PROC_MS_MPU_CFG] = &qhs_mdsp_ms_mpu_cfg,
+ [SLAVE_GEM_NOC_SNOC] = &qns_gem_noc_snoc,
+ [SLAVE_LLCC] = &qns_llcc,
+ [SLAVE_SERVICE_GEM_NOC] = &srvc_gemnoc,
+};
+
+static struct qcom_icc_desc sc7180_gem_noc = {
+ .nodes = gem_noc_nodes,
+ .num_nodes = ARRAY_SIZE(gem_noc_nodes),
+ .bcms = gem_noc_bcms,
+ .num_bcms = ARRAY_SIZE(gem_noc_bcms),
+};
+
+static struct qcom_icc_bcm *ipa_virt_bcms[] = {
+ &bcm_ip0,
+};
+
+static struct qcom_icc_node *ipa_virt_nodes[] = {
+ [MASTER_IPA_CORE] = &ipa_core_master,
+ [SLAVE_IPA_CORE] = &ipa_core_slave,
+};
+
+static struct qcom_icc_desc sc7180_ipa_virt = {
+ .nodes = ipa_virt_nodes,
+ .num_nodes = ARRAY_SIZE(ipa_virt_nodes),
+ .bcms = ipa_virt_bcms,
+ .num_bcms = ARRAY_SIZE(ipa_virt_bcms),
+};
+
+static struct qcom_icc_bcm *mc_virt_bcms[] = {
+ &bcm_acv,
+ &bcm_mc0,
+};
+
+static struct qcom_icc_node *mc_virt_nodes[] = {
+ [MASTER_LLCC] = &llcc_mc,
+ [SLAVE_EBI1] = &ebi,
+};
+
+static struct qcom_icc_desc sc7180_mc_virt = {
+ .nodes = mc_virt_nodes,
+ .num_nodes = ARRAY_SIZE(mc_virt_nodes),
+ .bcms = mc_virt_bcms,
+ .num_bcms = ARRAY_SIZE(mc_virt_bcms),
+};
+
+static struct qcom_icc_bcm *mmss_noc_bcms[] = {
+ &bcm_mm0,
+ &bcm_mm1,
+ &bcm_mm2,
+};
+
+static struct qcom_icc_node *mmss_noc_nodes[] = {
+ [MASTER_CNOC_MNOC_CFG] = &qhm_mnoc_cfg,
+ [MASTER_CAMNOC_HF0] = &qxm_camnoc_hf0,
+ [MASTER_CAMNOC_HF1] = &qxm_camnoc_hf1,
+ [MASTER_CAMNOC_SF] = &qxm_camnoc_sf,
+ [MASTER_MDP0] = &qxm_mdp0,
+ [MASTER_ROTATOR] = &qxm_rot,
+ [MASTER_VIDEO_P0] = &qxm_venus0,
+ [MASTER_VIDEO_PROC] = &qxm_venus_arm9,
+ [SLAVE_MNOC_HF_MEM_NOC] = &qns_mem_noc_hf,
+ [SLAVE_MNOC_SF_MEM_NOC] = &qns_mem_noc_sf,
+ [SLAVE_SERVICE_MNOC] = &srvc_mnoc,
+};
+
+static struct qcom_icc_desc sc7180_mmss_noc = {
+ .nodes = mmss_noc_nodes,
+ .num_nodes = ARRAY_SIZE(mmss_noc_nodes),
+ .bcms = mmss_noc_bcms,
+ .num_bcms = ARRAY_SIZE(mmss_noc_bcms),
+};
+
+static struct qcom_icc_node *npu_noc_nodes[] = {
+ [MASTER_NPU_SYS] = &amm_npu_sys,
+ [MASTER_NPU_NOC_CFG] = &qhm_npu_cfg,
+ [SLAVE_NPU_CAL_DP0] = &qhs_cal_dp0,
+ [SLAVE_NPU_CP] = &qhs_cp,
+ [SLAVE_NPU_INT_DMA_BWMON_CFG] = &qhs_dma_bwmon,
+ [SLAVE_NPU_DPM] = &qhs_dpm,
+ [SLAVE_ISENSE_CFG] = &qhs_isense,
+ [SLAVE_NPU_LLM_CFG] = &qhs_llm,
+ [SLAVE_NPU_TCM] = &qhs_tcm,
+ [SLAVE_NPU_COMPUTE_NOC] = &qns_npu_sys,
+ [SLAVE_SERVICE_NPU_NOC] = &srvc_noc,
+};
+
+static struct qcom_icc_desc sc7180_npu_noc = {
+ .nodes = npu_noc_nodes,
+ .num_nodes = ARRAY_SIZE(npu_noc_nodes),
+};
+
+static struct qcom_icc_bcm *qup_virt_bcms[] = {
+ &bcm_qup0,
+};
+
+static struct qcom_icc_node *qup_virt_nodes[] = {
+ [MASTER_QUP_CORE_0] = &qup_core_master_1,
+ [MASTER_QUP_CORE_1] = &qup_core_master_2,
+ [SLAVE_QUP_CORE_0] = &qup_core_slave_1,
+ [SLAVE_QUP_CORE_1] = &qup_core_slave_2,
+};
+
+static struct qcom_icc_desc sc7180_qup_virt = {
+ .nodes = qup_virt_nodes,
+ .num_nodes = ARRAY_SIZE(qup_virt_nodes),
+ .bcms = qup_virt_bcms,
+ .num_bcms = ARRAY_SIZE(qup_virt_bcms),
+};
+
+static struct qcom_icc_bcm *system_noc_bcms[] = {
+ &bcm_sn0,
+ &bcm_sn1,
+ &bcm_sn2,
+ &bcm_sn3,
+ &bcm_sn4,
+ &bcm_sn7,
+ &bcm_sn9,
+ &bcm_sn12,
+};
+
+static struct qcom_icc_node *system_noc_nodes[] = {
+ [MASTER_SNOC_CFG] = &qhm_snoc_cfg,
+ [MASTER_A1NOC_SNOC] = &qnm_aggre1_noc,
+ [MASTER_A2NOC_SNOC] = &qnm_aggre2_noc,
+ [MASTER_GEM_NOC_SNOC] = &qnm_gemnoc,
+ [MASTER_PIMEM] = &qxm_pimem,
+ [SLAVE_APPSS] = &qhs_apss,
+ [SLAVE_SNOC_CNOC] = &qns_cnoc,
+ [SLAVE_SNOC_GEM_NOC_GC] = &qns_gemnoc_gc,
+ [SLAVE_SNOC_GEM_NOC_SF] = &qns_gemnoc_sf,
+ [SLAVE_IMEM] = &qxs_imem,
+ [SLAVE_PIMEM] = &qxs_pimem,
+ [SLAVE_SERVICE_SNOC] = &srvc_snoc,
+ [SLAVE_QDSS_STM] = &xs_qdss_stm,
+ [SLAVE_TCU] = &xs_sys_tcu_cfg,
+};
+
+static struct qcom_icc_desc sc7180_system_noc = {
+ .nodes = system_noc_nodes,
+ .num_nodes = ARRAY_SIZE(system_noc_nodes),
+ .bcms = system_noc_bcms,
+ .num_bcms = ARRAY_SIZE(system_noc_bcms),
+};
+
+static int qnoc_probe(struct platform_device *pdev)
+{
+ const struct qcom_icc_desc *desc;
+ struct icc_onecell_data *data;
+ struct icc_provider *provider;
+ struct qcom_icc_node **qnodes;
+ struct qcom_icc_provider *qp;
+ struct icc_node *node;
+ size_t num_nodes, i;
+ int ret;
+
+ desc = of_device_get_match_data(&pdev->dev);
+ if (!desc)
+ return -EINVAL;
+
+ qnodes = desc->nodes;
+ num_nodes = desc->num_nodes;
+
+ qp = devm_kzalloc(&pdev->dev, sizeof(*qp), GFP_KERNEL);
+ if (!qp)
+ return -ENOMEM;
+
+ data = devm_kcalloc(&pdev->dev, num_nodes, sizeof(*node), GFP_KERNEL);
+ if (!data)
+ return -ENOMEM;
+
+ provider = &qp->provider;
+ provider->dev = &pdev->dev;
+ provider->set = qcom_icc_set;
+ provider->pre_aggregate = qcom_icc_pre_aggregate;
+ provider->aggregate = qcom_icc_aggregate;
+ provider->xlate = of_icc_xlate_onecell;
+ INIT_LIST_HEAD(&provider->nodes);
+ provider->data = data;
+
+ qp->dev = &pdev->dev;
+ qp->bcms = desc->bcms;
+ qp->num_bcms = desc->num_bcms;
+
+ qp->voter = of_bcm_voter_get(qp->dev, NULL);
+ if (IS_ERR(qp->voter))
+ return PTR_ERR(qp->voter);
+
+ ret = icc_provider_add(provider);
+ if (ret) {
+ dev_err(&pdev->dev, "error adding interconnect provider\n");
+ return ret;
+ }
+
+ for (i = 0; i < num_nodes; i++) {
+ size_t j;
+
+ if (!qnodes[i])
+ continue;
+
+ node = icc_node_create(qnodes[i]->id);
+ if (IS_ERR(node)) {
+ ret = PTR_ERR(node);
+ goto err;
+ }
+
+ node->name = qnodes[i]->name;
+ node->data = qnodes[i];
+ icc_node_add(node, provider);
+
+ dev_dbg(&pdev->dev, "registered node %pK %s %d\n", node,
+ qnodes[i]->name, node->id);
+
+ /* populate links */
+ for (j = 0; j < qnodes[i]->num_links; j++)
+ icc_link_create(node, qnodes[i]->links[j]);
+
+ data->nodes[i] = node;
+ }
+ data->num_nodes = num_nodes;
+
+ for (i = 0; i < qp->num_bcms; i++)
+ qcom_icc_bcm_init(qp->bcms[i], &pdev->dev);
+
+ platform_set_drvdata(pdev, qp);
+
+ dev_dbg(&pdev->dev, "Registered SC7180 ICC\n");
+
+ return ret;
+err:
+ icc_nodes_remove(provider);
+ icc_provider_del(provider);
+ return ret;
+}
+
+static int qnoc_remove(struct platform_device *pdev)
+{
+ struct qcom_icc_provider *qp = platform_get_drvdata(pdev);
+
+ icc_nodes_remove(&qp->provider);
+ return icc_provider_del(&qp->provider);
+}
+
+static const struct of_device_id qnoc_of_match[] = {
+ { .compatible = "qcom,sc7180-aggre1-noc",
+ .data = &sc7180_aggre1_noc},
+ { .compatible = "qcom,sc7180-aggre2-noc",
+ .data = &sc7180_aggre2_noc},
+ { .compatible = "qcom,sc7180-camnoc-virt",
+ .data = &sc7180_camnoc_virt},
+ { .compatible = "qcom,sc7180-compute-noc",
+ .data = &sc7180_compute_noc},
+ { .compatible = "qcom,sc7180-config-noc",
+ .data = &sc7180_config_noc},
+ { .compatible = "qcom,sc7180-dc-noc",
+ .data = &sc7180_dc_noc},
+ { .compatible = "qcom,sc7180-gem-noc",
+ .data = &sc7180_gem_noc},
+ { .compatible = "qcom,sc7180-ipa-virt",
+ .data = &sc7180_ipa_virt},
+ { .compatible = "qcom,sc7180-mc-virt",
+ .data = &sc7180_mc_virt},
+ { .compatible = "qcom,sc7180-mmss-noc",
+ .data = &sc7180_mmss_noc},
+ { .compatible = "qcom,sc7180-npu-noc",
+ .data = &sc7180_npu_noc},
+ { .compatible = "qcom,sc7180-qup-virt",
+ .data = &sc7180_qup_virt},
+ { .compatible = "qcom,sc7180-system-noc",
+ .data = &sc7180_system_noc},
+ { },
+};
+MODULE_DEVICE_TABLE(of, qnoc_of_match);
+
+static struct platform_driver qnoc_driver = {
+ .probe = qnoc_probe,
+ .remove = qnoc_remove,
+ .driver = {
+ .name = "qnoc-sc7180",
+ .of_match_table = qnoc_of_match,
+ },
+};
+module_platform_driver(qnoc_driver);
+
+MODULE_DESCRIPTION("Qualcomm SC7180 NoC driver");
+MODULE_LICENSE("GPL v2");
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 12+ messages in thread
* [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes
2019-12-31 8:58 [V2, 0/3] Add SC7180 interconnect provider driver Odelu Kukatla
2019-12-31 8:58 ` [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings Odelu Kukatla
2019-12-31 8:58 ` [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver Odelu Kukatla
@ 2019-12-31 8:58 ` Odelu Kukatla
2020-01-06 17:29 ` Georgi Djakov
2020-02-04 20:52 ` Evan Green
2 siblings, 2 replies; 12+ messages in thread
From: Odelu Kukatla @ 2019-12-31 8:58 UTC (permalink / raw)
To: georgi.djakov, daidavid1, bjorn.andersson, evgreen, Andy Gross,
Rob Herring, Mark Rutland, linux-arm-msm, devicetree,
linux-kernel
Cc: sboyd, ilina, seansw, elder, linux-pm, linux-arm-msm-owner,
Odelu Kukatla
Add the DT nodes for the network-on-chip interconnect buses found
on sc7180-based platforms.
---
arch/arm64/boot/dts/qcom/sc7180.dtsi | 96 ++++++++++++++++++++++++++++++++++++
1 file changed, 96 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
index 3676bfd..077b1e5 100644
--- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
+++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
@@ -8,6 +8,7 @@
#include <dt-bindings/clock/qcom,gcc-sc7180.h>
#include <dt-bindings/clock/qcom,rpmh.h>
#include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/interconnect/qcom,sc7180.h>
#include <dt-bindings/phy/phy-qcom-qusb2.h>
#include <dt-bindings/soc/qcom,rpmh-rsc.h>
@@ -1286,6 +1287,10 @@
clock-names = "xo";
#clock-cells = <1>;
};
+
+ apps_bcm_voter: bcm_voter {
+ compatible = "qcom,sc7180-bcm-voter";
+ };
};
cpufreq_hw: cpufreq@18323000 {
@@ -1298,6 +1303,97 @@
#freq-domain-cells = <1>;
};
+
+ config_noc: interconnect@1500000 {
+ compatible = "qcom,sc7180-config-noc";
+ reg = <0 0x01500000 0 0x28000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ system_noc: interconnect@1620000 {
+ compatible = "qcom,sc7180-system-noc";
+ reg = <0 0x01620000 0 0x17080>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mc_virt: interconnect@1630000 {
+ compatible = "qcom,sc7180-mc-virt";
+ reg = <0 0x01630000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ qup_virt: interconnect@1650000 {
+ compatible = "qcom,sc7180-qup-virt";
+ reg = <0 0x01650000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre1_noc: interconnect@16e0000 {
+ compatible = "qcom,sc7180-aggre1-noc";
+ reg = <0 0x016e0000 0 0x15080>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ aggre2_noc: interconnect@1700000 {
+ compatible = "qcom,sc7180-aggre2-noc";
+ reg = <0 0x01700000 0 0x1f880>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ compute_noc: interconnect@170e000 {
+ compatible = "qcom,sc7180-compute-noc";
+ reg = <0 0x0170e000 0 0x11880>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ mmss_noc: interconnect@1740000 {
+ compatible = "qcom,sc7180-mmss-noc";
+ reg = <0 0x01740000 0 0x1c100>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ ipa_virt: interconnect@1e00000 {
+ compatible = "qcom,sc7180-ipa-virt";
+ reg = <0 0x01e00000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ dc_noc: interconnect@9160000 {
+ compatible = "qcom,sc7180-dc-noc";
+ reg = <0 0x09160000 0 0x03200>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ gem_noc: interconnect@9680000 {
+ compatible = "qcom,sc7180-gem-noc";
+ reg = <0 0x09680000 0 0x3e200>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ npu_noc: interconnect@9990000 {
+ compatible = "qcom,sc7180-npu-noc";
+ reg = <0 0x09990000 0 0x1600>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
+
+ camnoc_virt: interconnect@ac00000 {
+ compatible = "qcom,sc7180-camnoc-virt";
+ reg = <0 0x0ac00000 0 0x4000>;
+ #interconnect-cells = <1>;
+ qcom,bcm-voters = <&apps_bcm_voter>;
+ };
};
thermal-zones {
--
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project
^ permalink raw reply related [flat|nested] 12+ messages in thread
* Re: [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
2019-12-31 8:58 ` [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings Odelu Kukatla
@ 2020-01-04 22:01 ` Rob Herring
2020-01-04 23:08 ` Aaro Koskinen
2020-02-21 7:33 ` okukatla
0 siblings, 2 replies; 12+ messages in thread
From: Rob Herring @ 2020-01-04 22:01 UTC (permalink / raw)
To: Odelu Kukatla
Cc: georgi.djakov, daidavid1, bjorn.andersson, evgreen, Andy Gross,
Mark Rutland, linux-arm-msm, linux-pm, devicetree, linux-kernel,
sboyd, ilina, seansw, elder, linux-arm-msm-owner
On Tue, Dec 31, 2019 at 02:28:55PM +0530, Odelu Kukatla wrote:
> The Qualcomm SC7180 platform has several bus fabrics that could be
> controlled and tuned dynamically according to the bandwidth demand.
>
> Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
> ---
> .../bindings/interconnect/qcom,bcm-voter.yaml | 1 +
> .../bindings/interconnect/qcom,sc7180.yaml | 155 ++++++++++++++++++++
> include/dt-bindings/interconnect/qcom,sc7180.h | 161 +++++++++++++++++++++
> 3 files changed, 317 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> create mode 100644 include/dt-bindings/interconnect/qcom,sc7180.h
>
> diff --git a/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml b/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
> index 74f0715..55c9f34 100644
> --- a/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
> +++ b/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
> @@ -19,6 +19,7 @@ description: |
> properties:
> compatible:
> enum:
> + - qcom,sc7180-bcm-voter
> - qcom,sdm845-bcm-voter
>
> required:
> diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> new file mode 100644
> index 0000000..487da5e
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> @@ -0,0 +1,155 @@
> +# SPDX-License-Identifier: GPL-2.0
Dual license new bindings:
(GPL-2.0-only OR BSD-2-Clause)
With that,
Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
2020-01-04 22:01 ` Rob Herring
@ 2020-01-04 23:08 ` Aaro Koskinen
2020-01-05 23:07 ` Rob Herring
2020-02-21 7:33 ` okukatla
1 sibling, 1 reply; 12+ messages in thread
From: Aaro Koskinen @ 2020-01-04 23:08 UTC (permalink / raw)
To: Rob Herring
Cc: Odelu Kukatla, georgi.djakov, daidavid1, bjorn.andersson,
evgreen, Andy Gross, Mark Rutland, linux-arm-msm, linux-pm,
devicetree, linux-kernel, sboyd, ilina, seansw, elder,
linux-arm-msm-owner
Hi,
On Sat, Jan 04, 2020 at 03:01:42PM -0700, Rob Herring wrote:
> On Tue, Dec 31, 2019 at 02:28:55PM +0530, Odelu Kukatla wrote:
> > diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> > new file mode 100644
> > index 0000000..487da5e
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> > @@ -0,0 +1,155 @@
> > +# SPDX-License-Identifier: GPL-2.0
>
> Dual license new bindings:
>
> (GPL-2.0-only OR BSD-2-Clause)
Just curious, is that mandatory for any new bindings?
A.
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver
2019-12-31 8:58 ` [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver Odelu Kukatla
@ 2020-01-05 6:55 ` Stephen Boyd
2020-02-21 8:43 ` okukatla
0 siblings, 1 reply; 12+ messages in thread
From: Stephen Boyd @ 2020-01-05 6:55 UTC (permalink / raw)
To: Andy Gross, Odelu Kukatla, bjorn.andersson, daidavid1, evgreen,
georgi.djakov, linux-arm-msm, linux-kernel, linux-pm
Cc: ilina, seansw, elder, linux-arm-msm-owner, Odelu Kukatla
Quoting Odelu Kukatla (2019-12-31 00:58:56)
> diff --git a/drivers/interconnect/qcom/sc7180.c b/drivers/interconnect/qcom/sc7180.c
> new file mode 100644
> index 0000000..4a398e0
> --- /dev/null
> +++ b/drivers/interconnect/qcom/sc7180.c
> @@ -0,0 +1,788 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019, The Linux Foundation. All rights reserved.
> + *
> + */
> +
> +#include <dt-bindings/interconnect/qcom,sc7180.h>
Can you include this after linux/ headers? That is the "preferred" way
to include headers.
> +#include <linux/device.h>
> +#include <linux/interconnect.h>
> +#include <linux/interconnect-provider.h>
> +#include <linux/module.h>
> +#include <linux/of_device.h>
Hopefully this include isn't used and can be removed.
> +#include <linux/of_platform.h>
Is this include used?
> +#include <linux/platform_device.h>
> +
> +#include "icc-rpmh.h"
> +#include "bcm-voter.h"
> +
[...]
> +
> +static struct qcom_icc_node *system_noc_nodes[] = {
> + [MASTER_SNOC_CFG] = &qhm_snoc_cfg,
> + [MASTER_A1NOC_SNOC] = &qnm_aggre1_noc,
> + [MASTER_A2NOC_SNOC] = &qnm_aggre2_noc,
> + [MASTER_GEM_NOC_SNOC] = &qnm_gemnoc,
> + [MASTER_PIMEM] = &qxm_pimem,
> + [SLAVE_APPSS] = &qhs_apss,
> + [SLAVE_SNOC_CNOC] = &qns_cnoc,
> + [SLAVE_SNOC_GEM_NOC_GC] = &qns_gemnoc_gc,
> + [SLAVE_SNOC_GEM_NOC_SF] = &qns_gemnoc_sf,
> + [SLAVE_IMEM] = &qxs_imem,
> + [SLAVE_PIMEM] = &qxs_pimem,
> + [SLAVE_SERVICE_SNOC] = &srvc_snoc,
> + [SLAVE_QDSS_STM] = &xs_qdss_stm,
> + [SLAVE_TCU] = &xs_sys_tcu_cfg,
> +};
> +
> +static struct qcom_icc_desc sc7180_system_noc = {
Can this be const? And the other ones?
> + .nodes = system_noc_nodes,
> + .num_nodes = ARRAY_SIZE(system_noc_nodes),
> + .bcms = system_noc_bcms,
> + .num_bcms = ARRAY_SIZE(system_noc_bcms),
> +};
> +
> +static int qnoc_probe(struct platform_device *pdev)
> +{
> + const struct qcom_icc_desc *desc;
> + struct icc_onecell_data *data;
> + struct icc_provider *provider;
> + struct qcom_icc_node **qnodes;
> + struct qcom_icc_provider *qp;
> + struct icc_node *node;
> + size_t num_nodes, i;
> + int ret;
> +
> + desc = of_device_get_match_data(&pdev->dev);
Use device_get_match_data() instead?
> + if (!desc)
> + return -EINVAL;
> +
> + qnodes = desc->nodes;
> + num_nodes = desc->num_nodes;
> +
> + qp = devm_kzalloc(&pdev->dev, sizeof(*qp), GFP_KERNEL);
> + if (!qp)
> + return -ENOMEM;
> +
> + data = devm_kcalloc(&pdev->dev, num_nodes, sizeof(*node), GFP_KERNEL);
> + if (!data)
> + return -ENOMEM;
> +
> + provider = &qp->provider;
> + provider->dev = &pdev->dev;
> + provider->set = qcom_icc_set;
> + provider->pre_aggregate = qcom_icc_pre_aggregate;
> + provider->aggregate = qcom_icc_aggregate;
> + provider->xlate = of_icc_xlate_onecell;
> + INIT_LIST_HEAD(&provider->nodes);
> + provider->data = data;
> +
> + qp->dev = &pdev->dev;
> + qp->bcms = desc->bcms;
> + qp->num_bcms = desc->num_bcms;
> +
> + qp->voter = of_bcm_voter_get(qp->dev, NULL);
> + if (IS_ERR(qp->voter))
> + return PTR_ERR(qp->voter);
> +
> + ret = icc_provider_add(provider);
> + if (ret) {
> + dev_err(&pdev->dev, "error adding interconnect provider\n");
> + return ret;
> + }
> +
> + for (i = 0; i < num_nodes; i++) {
> + size_t j;
> +
> + if (!qnodes[i])
> + continue;
> +
> + node = icc_node_create(qnodes[i]->id);
> + if (IS_ERR(node)) {
> + ret = PTR_ERR(node);
> + goto err;
> + }
> +
> + node->name = qnodes[i]->name;
> + node->data = qnodes[i];
> + icc_node_add(node, provider);
> +
> + dev_dbg(&pdev->dev, "registered node %pK %s %d\n", node,
> + qnodes[i]->name, node->id);
Is this more debug junk? Maybe if it is useful it can be part of the
core framework instead of in this driver?
> +
> + /* populate links */
Useless comment.
> + for (j = 0; j < qnodes[i]->num_links; j++)
> + icc_link_create(node, qnodes[i]->links[j]);
> +
> + data->nodes[i] = node;
> + }
> + data->num_nodes = num_nodes;
> +
> + for (i = 0; i < qp->num_bcms; i++)
> + qcom_icc_bcm_init(qp->bcms[i], &pdev->dev);
> +
> + platform_set_drvdata(pdev, qp);
> +
> + dev_dbg(&pdev->dev, "Registered SC7180 ICC\n");
This driver debug message is pretty useless. Please remove it.
> +
> + return ret;
return 0?
> +err:
> + icc_nodes_remove(provider);
> + icc_provider_del(provider);
> + return ret;
> +}
> +
> +static int qnoc_remove(struct platform_device *pdev)
> +{
> + struct qcom_icc_provider *qp = platform_get_drvdata(pdev);
> +
> + icc_nodes_remove(&qp->provider);
> + return icc_provider_del(&qp->provider);
> +}
> +
> +static const struct of_device_id qnoc_of_match[] = {
> + { .compatible = "qcom,sc7180-aggre1-noc",
> + .data = &sc7180_aggre1_noc},
> + { .compatible = "qcom,sc7180-aggre2-noc",
> + .data = &sc7180_aggre2_noc},
> + { .compatible = "qcom,sc7180-camnoc-virt",
> + .data = &sc7180_camnoc_virt},
> + { .compatible = "qcom,sc7180-compute-noc",
> + .data = &sc7180_compute_noc},
> + { .compatible = "qcom,sc7180-config-noc",
> + .data = &sc7180_config_noc},
> + { .compatible = "qcom,sc7180-dc-noc",
> + .data = &sc7180_dc_noc},
> + { .compatible = "qcom,sc7180-gem-noc",
> + .data = &sc7180_gem_noc},
> + { .compatible = "qcom,sc7180-ipa-virt",
> + .data = &sc7180_ipa_virt},
> + { .compatible = "qcom,sc7180-mc-virt",
> + .data = &sc7180_mc_virt},
> + { .compatible = "qcom,sc7180-mmss-noc",
> + .data = &sc7180_mmss_noc},
> + { .compatible = "qcom,sc7180-npu-noc",
> + .data = &sc7180_npu_noc},
> + { .compatible = "qcom,sc7180-qup-virt",
> + .data = &sc7180_qup_virt},
> + { .compatible = "qcom,sc7180-system-noc",
> + .data = &sc7180_system_noc},
> + { },
Nitpick: Drop the comma as it's the sentinel and nothing can come after.
> +};
> +MODULE_DEVICE_TABLE(of, qnoc_of_match);
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
2020-01-04 23:08 ` Aaro Koskinen
@ 2020-01-05 23:07 ` Rob Herring
0 siblings, 0 replies; 12+ messages in thread
From: Rob Herring @ 2020-01-05 23:07 UTC (permalink / raw)
To: Aaro Koskinen
Cc: Odelu Kukatla, Georgi Djakov, David Dai, Bjorn Andersson,
evgreen, Andy Gross, Mark Rutland, linux-arm-msm,
open list:THERMAL, devicetree, linux-kernel, Stephen Boyd,
Lina Iyer, Sweeney, Sean, Alex Elder, linux-arm-msm-owner
On Sat, Jan 4, 2020 at 4:09 PM Aaro Koskinen <aaro.koskinen@iki.fi> wrote:
>
> Hi,
>
> On Sat, Jan 04, 2020 at 03:01:42PM -0700, Rob Herring wrote:
> > On Tue, Dec 31, 2019 at 02:28:55PM +0530, Odelu Kukatla wrote:
> > > diff --git a/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> > > new file mode 100644
> > > index 0000000..487da5e
> > > --- /dev/null
> > > +++ b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
> > > @@ -0,0 +1,155 @@
> > > +# SPDX-License-Identifier: GPL-2.0
> >
> > Dual license new bindings:
> >
> > (GPL-2.0-only OR BSD-2-Clause)
>
> Just curious, is that mandatory for any new bindings?
Yes.
Rob
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes
2019-12-31 8:58 ` [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes Odelu Kukatla
@ 2020-01-06 17:29 ` Georgi Djakov
2020-02-04 20:52 ` Evan Green
1 sibling, 0 replies; 12+ messages in thread
From: Georgi Djakov @ 2020-01-06 17:29 UTC (permalink / raw)
To: Odelu Kukatla, daidavid1, bjorn.andersson, evgreen, Andy Gross,
Rob Herring, Mark Rutland, linux-arm-msm, devicetree,
linux-kernel
Cc: sboyd, ilina, seansw, elder, linux-pm, linux-arm-msm-owner
On 31.12.19 г. 10:58 ч., Odelu Kukatla wrote:
> Add the DT nodes for the network-on-chip interconnect buses found
> on sc7180-based platforms.
> ---
> arch/arm64/boot/dts/qcom/sc7180.dtsi | 96 ++++++++++++++++++++++++++++++++++++
> 1 file changed, 96 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sc7180.dtsi b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> index 3676bfd..077b1e5 100644
> --- a/arch/arm64/boot/dts/qcom/sc7180.dtsi
> +++ b/arch/arm64/boot/dts/qcom/sc7180.dtsi
> @@ -8,6 +8,7 @@
> #include <dt-bindings/clock/qcom,gcc-sc7180.h>
> #include <dt-bindings/clock/qcom,rpmh.h>
> #include <dt-bindings/interrupt-controller/arm-gic.h>
> +#include <dt-bindings/interconnect/qcom,sc7180.h>
This should be moved one line up if we want to keep the headers sorted.
> #include <dt-bindings/phy/phy-qcom-qusb2.h>
> #include <dt-bindings/soc/qcom,rpmh-rsc.h>
>
> @@ -1286,6 +1287,10 @@
> clock-names = "xo";
> #clock-cells = <1>;
> };
> +
> + apps_bcm_voter: bcm_voter {
> + compatible = "qcom,sc7180-bcm-voter";
> + };
> };
>
> cpufreq_hw: cpufreq@18323000 {
> @@ -1298,6 +1303,97 @@
>
> #freq-domain-cells = <1>;
> };
> + > + config_noc: interconnect@1500000 {
All DT nodes in this file are ordered by their address. Please move these up
to keep it consistent.
Thanks,
Georgi
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes
2019-12-31 8:58 ` [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes Odelu Kukatla
2020-01-06 17:29 ` Georgi Djakov
@ 2020-02-04 20:52 ` Evan Green
1 sibling, 0 replies; 12+ messages in thread
From: Evan Green @ 2020-02-04 20:52 UTC (permalink / raw)
To: Odelu Kukatla
Cc: Georgi Djakov, David Dai, Bjorn Andersson, Andy Gross,
Rob Herring, Mark Rutland, linux-arm-msm,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS, LKML,
sboyd, Lina Iyer, Sean Sweeney, Alex Elder, linux-pm,
linux-arm-msm-owner
On Tue, Dec 31, 2019 at 1:00 AM Odelu Kukatla <okukatla@codeaurora.org> wrote:
>
> Add the DT nodes for the network-on-chip interconnect buses found
> on sc7180-based platforms.
> ---
Hi Odelu,
Are you going to spin this series?
-Evan
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings
2020-01-04 22:01 ` Rob Herring
2020-01-04 23:08 ` Aaro Koskinen
@ 2020-02-21 7:33 ` okukatla
1 sibling, 0 replies; 12+ messages in thread
From: okukatla @ 2020-02-21 7:33 UTC (permalink / raw)
To: Rob Herring
Cc: georgi.djakov, daidavid1, bjorn.andersson, evgreen, Andy Gross,
Mark Rutland, linux-arm-msm, linux-pm, devicetree, linux-kernel,
sboyd, ilina, seansw, elder, linux-arm-msm-owner
On 2020-01-05 03:31, Rob Herring wrote:
> On Tue, Dec 31, 2019 at 02:28:55PM +0530, Odelu Kukatla wrote:
>> The Qualcomm SC7180 platform has several bus fabrics that could be
>> controlled and tuned dynamically according to the bandwidth demand.
>>
>> Signed-off-by: Odelu Kukatla <okukatla@codeaurora.org>
>> ---
>> .../bindings/interconnect/qcom,bcm-voter.yaml | 1 +
>> .../bindings/interconnect/qcom,sc7180.yaml | 155
>> ++++++++++++++++++++
>> include/dt-bindings/interconnect/qcom,sc7180.h | 161
>> +++++++++++++++++++++
>> 3 files changed, 317 insertions(+)
>> create mode 100644
>> Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
>> create mode 100644 include/dt-bindings/interconnect/qcom,sc7180.h
>>
>> diff --git
>> a/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
>> b/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
>> index 74f0715..55c9f34 100644
>> ---
>> a/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
>> +++
>> b/Documentation/devicetree/bindings/interconnect/qcom,bcm-voter.yaml
>> @@ -19,6 +19,7 @@ description: |
>> properties:
>> compatible:
>> enum:
>> + - qcom,sc7180-bcm-voter
>> - qcom,sdm845-bcm-voter
>>
>> required:
>> diff --git
>> a/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
>> b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
>> new file mode 100644
>> index 0000000..487da5e
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/interconnect/qcom,sc7180.yaml
>> @@ -0,0 +1,155 @@
>> +# SPDX-License-Identifier: GPL-2.0
>
> Dual license new bindings:
>
> (GPL-2.0-only OR BSD-2-Clause)
>
Thanks Rob!
I will update it.
> With that,
>
> Reviewed-by: Rob Herring <robh@kernel.org>
^ permalink raw reply [flat|nested] 12+ messages in thread
* Re: [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver
2020-01-05 6:55 ` Stephen Boyd
@ 2020-02-21 8:43 ` okukatla
0 siblings, 0 replies; 12+ messages in thread
From: okukatla @ 2020-02-21 8:43 UTC (permalink / raw)
To: Stephen Boyd
Cc: Andy Gross, bjorn.andersson, daidavid1, evgreen, georgi.djakov,
linux-arm-msm, linux-kernel, linux-pm, ilina, seansw, elder,
linux-arm-msm-owner
On 2020-01-05 12:25, Stephen Boyd wrote:
> Quoting Odelu Kukatla (2019-12-31 00:58:56)
>> diff --git a/drivers/interconnect/qcom/sc7180.c
>> b/drivers/interconnect/qcom/sc7180.c
>> new file mode 100644
>> index 0000000..4a398e0
>> --- /dev/null
>> +++ b/drivers/interconnect/qcom/sc7180.c
>> @@ -0,0 +1,788 @@
>> +// SPDX-License-Identifier: GPL-2.0
>> +/*
>> + * Copyright (c) 2019, The Linux Foundation. All rights reserved.
>> + *
>> + */
>> +
>> +#include <dt-bindings/interconnect/qcom,sc7180.h>
>
> Can you include this after linux/ headers? That is the "preferred" way
> to include headers.
>
done.
>> +#include <linux/device.h>
>> +#include <linux/interconnect.h>
>> +#include <linux/interconnect-provider.h>
>> +#include <linux/module.h>
>> +#include <linux/of_device.h>
>
> Hopefully this include isn't used and can be removed.
>
I will remove it.
>> +#include <linux/of_platform.h>
>
> Is this include used?
>
I will remove it.
>> +#include <linux/platform_device.h>
>> +
>> +#include "icc-rpmh.h"
>> +#include "bcm-voter.h"
>> +
> [...]
>> +
>> +static struct qcom_icc_node *system_noc_nodes[] = {
>> + [MASTER_SNOC_CFG] = &qhm_snoc_cfg,
>> + [MASTER_A1NOC_SNOC] = &qnm_aggre1_noc,
>> + [MASTER_A2NOC_SNOC] = &qnm_aggre2_noc,
>> + [MASTER_GEM_NOC_SNOC] = &qnm_gemnoc,
>> + [MASTER_PIMEM] = &qxm_pimem,
>> + [SLAVE_APPSS] = &qhs_apss,
>> + [SLAVE_SNOC_CNOC] = &qns_cnoc,
>> + [SLAVE_SNOC_GEM_NOC_GC] = &qns_gemnoc_gc,
>> + [SLAVE_SNOC_GEM_NOC_SF] = &qns_gemnoc_sf,
>> + [SLAVE_IMEM] = &qxs_imem,
>> + [SLAVE_PIMEM] = &qxs_pimem,
>> + [SLAVE_SERVICE_SNOC] = &srvc_snoc,
>> + [SLAVE_QDSS_STM] = &xs_qdss_stm,
>> + [SLAVE_TCU] = &xs_sys_tcu_cfg,
>> +};
>> +
>> +static struct qcom_icc_desc sc7180_system_noc = {
>
> Can this be const? And the other ones?
> yes, will change it.
>> + .nodes = system_noc_nodes,
>> + .num_nodes = ARRAY_SIZE(system_noc_nodes),
>> + .bcms = system_noc_bcms,
>> + .num_bcms = ARRAY_SIZE(system_noc_bcms),
>> +};
>> +
>> +static int qnoc_probe(struct platform_device *pdev)
>> +{
>> + const struct qcom_icc_desc *desc;
>> + struct icc_onecell_data *data;
>> + struct icc_provider *provider;
>> + struct qcom_icc_node **qnodes;
>> + struct qcom_icc_provider *qp;
>> + struct icc_node *node;
>> + size_t num_nodes, i;
>> + int ret;
>> +
>> + desc = of_device_get_match_data(&pdev->dev);
>
> Use device_get_match_data() instead?
>
will update it.
>> + if (!desc)
>> + return -EINVAL;
>> +
>> + qnodes = desc->nodes;
>> + num_nodes = desc->num_nodes;
>> +
>> + qp = devm_kzalloc(&pdev->dev, sizeof(*qp), GFP_KERNEL);
>> + if (!qp)
>> + return -ENOMEM;
>> +
>> + data = devm_kcalloc(&pdev->dev, num_nodes, sizeof(*node),
>> GFP_KERNEL);
>> + if (!data)
>> + return -ENOMEM;
>> +
>> + provider = &qp->provider;
>> + provider->dev = &pdev->dev;
>> + provider->set = qcom_icc_set;
>> + provider->pre_aggregate = qcom_icc_pre_aggregate;
>> + provider->aggregate = qcom_icc_aggregate;
>> + provider->xlate = of_icc_xlate_onecell;
>> + INIT_LIST_HEAD(&provider->nodes);
>> + provider->data = data;
>> +
>> + qp->dev = &pdev->dev;
>> + qp->bcms = desc->bcms;
>> + qp->num_bcms = desc->num_bcms;
>> +
>> + qp->voter = of_bcm_voter_get(qp->dev, NULL);
>> + if (IS_ERR(qp->voter))
>> + return PTR_ERR(qp->voter);
>> +
>> + ret = icc_provider_add(provider);
>> + if (ret) {
>> + dev_err(&pdev->dev, "error adding interconnect
>> provider\n");
>> + return ret;
>> + }
>> +
>> + for (i = 0; i < num_nodes; i++) {
>> + size_t j;
>> +
>> + if (!qnodes[i])
>> + continue;
>> +
>> + node = icc_node_create(qnodes[i]->id);
>> + if (IS_ERR(node)) {
>> + ret = PTR_ERR(node);
>> + goto err;
>> + }
>> +
>> + node->name = qnodes[i]->name;
>> + node->data = qnodes[i];
>> + icc_node_add(node, provider);
>> +
>> + dev_dbg(&pdev->dev, "registered node %pK %s %d\n",
>> node,
>> + qnodes[i]->name, node->id);
>
> Is this more debug junk? Maybe if it is useful it can be part of the
> core framework instead of in this driver?
>
>> +
>> + /* populate links */
>
> Useless comment.
> i will clean up this.
>> + for (j = 0; j < qnodes[i]->num_links; j++)
>> + icc_link_create(node, qnodes[i]->links[j]);
>> +
>> + data->nodes[i] = node;
>> + }
>> + data->num_nodes = num_nodes;
>> +
>> + for (i = 0; i < qp->num_bcms; i++)
>> + qcom_icc_bcm_init(qp->bcms[i], &pdev->dev);
>> +
>> + platform_set_drvdata(pdev, qp);
>> +
>> + dev_dbg(&pdev->dev, "Registered SC7180 ICC\n");
>
> This driver debug message is pretty useless. Please remove it.
> i will removr it.
>> +
>> + return ret;
>
> return 0?
>
>> +err:
>> + icc_nodes_remove(provider);
>> + icc_provider_del(provider);
>> + return ret;
>> +}
>> +
>> +static int qnoc_remove(struct platform_device *pdev)
>> +{
>> + struct qcom_icc_provider *qp = platform_get_drvdata(pdev);
>> +
>> + icc_nodes_remove(&qp->provider);
>> + return icc_provider_del(&qp->provider);
>> +}
>> +
>> +static const struct of_device_id qnoc_of_match[] = {
>> + { .compatible = "qcom,sc7180-aggre1-noc",
>> + .data = &sc7180_aggre1_noc},
>> + { .compatible = "qcom,sc7180-aggre2-noc",
>> + .data = &sc7180_aggre2_noc},
>> + { .compatible = "qcom,sc7180-camnoc-virt",
>> + .data = &sc7180_camnoc_virt},
>> + { .compatible = "qcom,sc7180-compute-noc",
>> + .data = &sc7180_compute_noc},
>> + { .compatible = "qcom,sc7180-config-noc",
>> + .data = &sc7180_config_noc},
>> + { .compatible = "qcom,sc7180-dc-noc",
>> + .data = &sc7180_dc_noc},
>> + { .compatible = "qcom,sc7180-gem-noc",
>> + .data = &sc7180_gem_noc},
>> + { .compatible = "qcom,sc7180-ipa-virt",
>> + .data = &sc7180_ipa_virt},
>> + { .compatible = "qcom,sc7180-mc-virt",
>> + .data = &sc7180_mc_virt},
>> + { .compatible = "qcom,sc7180-mmss-noc",
>> + .data = &sc7180_mmss_noc},
>> + { .compatible = "qcom,sc7180-npu-noc",
>> + .data = &sc7180_npu_noc},
>> + { .compatible = "qcom,sc7180-qup-virt",
>> + .data = &sc7180_qup_virt},
>> + { .compatible = "qcom,sc7180-system-noc",
>> + .data = &sc7180_system_noc},
>> + { },
>
> Nitpick: Drop the comma as it's the sentinel and nothing can come
> after.
> will remove it.
>> +};
>> +MODULE_DEVICE_TABLE(of, qnoc_of_match);
^ permalink raw reply [flat|nested] 12+ messages in thread
end of thread, other threads:[~2020-02-21 8:43 UTC | newest]
Thread overview: 12+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-12-31 8:58 [V2, 0/3] Add SC7180 interconnect provider driver Odelu Kukatla
2019-12-31 8:58 ` [V2, 1/3] dt-bindings: interconnect: Add Qualcomm SC7180 DT bindings Odelu Kukatla
2020-01-04 22:01 ` Rob Herring
2020-01-04 23:08 ` Aaro Koskinen
2020-01-05 23:07 ` Rob Herring
2020-02-21 7:33 ` okukatla
2019-12-31 8:58 ` [V2, 2/3] interconnect: qcom: Add SC7180 interconnect provider driver Odelu Kukatla
2020-01-05 6:55 ` Stephen Boyd
2020-02-21 8:43 ` okukatla
2019-12-31 8:58 ` [V2, 3/3] arm64: dts: sc7180: Add interconnect provider DT nodes Odelu Kukatla
2020-01-06 17:29 ` Georgi Djakov
2020-02-04 20:52 ` Evan Green
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).