From: Konrad Dybcio <konradybcio@gmail.com>
To: Amit Kucheria <amit.kucheria@linaro.org>
Cc: skrzynka@konradybcio.pl, Andy Gross <agross@kernel.org>,
Bjorn Andersson <bjorn.andersson@linaro.org>,
Zhang Rui <rui.zhang@intel.com>,
Daniel Lezcano <daniel.lezcano@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Linux PM list <linux-pm@vger.kernel.org>,
linux-arm-msm <linux-arm-msm@vger.kernel.org>,
DTML <devicetree@vger.kernel.org>,
Linux Kernel Mailing List <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 1/2] thermal: qcom: tsens-v0_1: Add support for MSM8939
Date: Mon, 4 May 2020 10:04:14 +0200 [thread overview]
Message-ID: <CAMS8qEXAPTcCYTKSA1VYnHtqT1zuUdYNNskRfgPiFykdKdqsKA@mail.gmail.com> (raw)
In-Reply-To: <CAP245DUOcsort1B1ftWW251Bzxp8=SuaGdZuZBmUubO9tw78cw@mail.gmail.com>
Thanks for your review. I'll hopefully send a v2 later today.
As for the sensor count, I don't know how many there actually are. I'm
an independent dev and don't have access to any documentation and I'm
solely basing on what I find in downstream, and I think it's 10,
unless mainline expects the _0_4 and _5 to be counted separately.. [1]
I will also make sure to test it again before sending and will give
you the results in the v2 cover letter.
[1] https://github.com/konradybcio/android_kernel_asus_msm8916-1/blob/minimal/drivers/thermal/msm8974-tsens.c#L396
pon., 4 maj 2020 o 08:31 Amit Kucheria <amit.kucheria@linaro.org> napisał(a):
>
> On Sat, May 2, 2020 at 2:03 AM Konrad Dybcio <konradybcio@gmail.com> wrote:
> >
> > Signed-off-by: Konrad Dybcio <konradybcio@gmail.com>
> > ---
> > drivers/thermal/qcom/tsens-v0_1.c | 142 +++++++++++++++++++++++++++++-
> > drivers/thermal/qcom/tsens.c | 3 +
> > drivers/thermal/qcom/tsens.h | 2 +-
> > 3 files changed, 145 insertions(+), 2 deletions(-)
> >
> > diff --git a/drivers/thermal/qcom/tsens-v0_1.c b/drivers/thermal/qcom/tsens-v0_1.c
> > index 959a9371d205c..29b95886273b7 100644
> > --- a/drivers/thermal/qcom/tsens-v0_1.c
> > +++ b/drivers/thermal/qcom/tsens-v0_1.c
> > @@ -48,6 +48,64 @@
> > #define MSM8916_CAL_SEL_MASK 0xe0000000
> > #define MSM8916_CAL_SEL_SHIFT 29
> >
> > +/* eeprom layout data for 8939 */
> > +#define MSM8939_BASE0_MASK 0x000000ff
> > +#define MSM8939_BASE1_MASK 0xff000000
> > +#define MSM8939_BASE0_SHIFT
>
> Use 0?
>
> > +#define MSM8939_BASE1_SHIFT 24
> > +
> > +#define MSM8939_S0_P1_MASK 0x000001f8
> > +#define MSM8939_S1_P1_MASK 0x001f8000
> > +#define MSM8939_S2_P1_MASK_0_4 0xf8000000
> > +#define MSM8939_S2_P1_MASK_5 0x00000001
> > +#define MSM8939_S3_P1_MASK 0x00001f80
> > +#define MSM8939_S4_P1_MASK 0x01f80000
> > +#define MSM8939_S5_P1_MASK 0x00003f00
> > +#define MSM8939_S6_P1_MASK 0x03f00000
> > +#define MSM8939_S7_P1_MASK 0x0000003f
> > +#define MSM8939_S8_P1_MASK 0x0003f000
> > +#define MSM8939_S9_P1_MASK 0x07e00000
> > +
> > +#define MSM8939_S0_P2_MASK 0x00007e00
> > +#define MSM8939_S1_P2_MASK 0x07e00000
> > +#define MSM8939_S2_P2_MASK 0x0000007e
> > +#define MSM8939_S3_P2_MASK 0x0007e000
> > +#define MSM8939_S4_P2_MASK 0x7e000000
> > +#define MSM8939_S5_P2_MASK 0x000fc000
> > +#define MSM8939_S6_P2_MASK 0xfc000000
> > +#define MSM8939_S7_P2_MASK 0x00000fc0
> > +#define MSM8939_S8_P2_MASK 0x00fc0000
> > +#define MSM8939_S9_P2_MASK_0_4 0xf8000000
> > +#define MSM8939_S9_P2_MASK_5 0x00002000
> > +
> > +#define MSM8939_CAL_SEL_MASK 0xc0000000
> > +#define MSM8939_CAL_SEL_SHIFT 0
> > +
> > +
>
> Get rid of extra line.
>
> > +#define MSM8939_S0_P1_SHIFT 3
> > +#define MSM8939_S1_P1_SHIFT 15
> > +#define MSM8939_S2_P1_SHIFT_0_4 27
> > +#define MSM8939_S2_P1_SHIFT_5 5
> > +#define MSM8939_S3_P1_SHIFT 7
> > +#define MSM8939_S4_P1_SHIFT 19
> > +#define MSM8939_S5_P1_SHIFT 8
> > +#define MSM8939_S6_P1_SHIFT 20
> > +//yes, 7 is missing in downstream
>
> Use C style comments.
>
> > +#define MSM8939_S8_P1_SHIFT 12
> > +#define MSM8939_S9_P1_SHIFT 21
> > +
> > +#define MSM8939_S0_P2_SHIFT 9
> > +#define MSM8939_S1_P2_SHIFT 21
> > +#define MSM8939_S2_P2_SHIFT 1
> > +#define MSM8939_S3_P2_SHIFT 13
> > +#define MSM8939_S4_P2_SHIFT 25
> > +#define MSM8939_S5_P2_SHIFT 14
> > +#define MSM8939_S6_P2_SHIFT 26
> > +#define MSM8939_S7_P2_SHIFT 6
> > +#define MSM8939_S8_P2_SHIFT 18
> > +#define MSM8939_S9_P2_SHIFT_0_4 27
> > +#define MSM8939_S9_P2_SHIFT_5 8
> > +
> > /* eeprom layout data for 8974 */
> > #define BASE1_MASK 0xff
> > #define S0_P1_MASK 0x3f00
> > @@ -189,6 +247,73 @@ static int calibrate_8916(struct tsens_priv *priv)
> > return 0;
> > }
> >
> > +static int calibrate_8939(struct tsens_priv *priv)
> > +{
> > + int base0 = 0, base1 = 0, i;
> > + u32 p1[11], p2[11];
> > + int mode = 0;
> > + u32 *qfprom_cdata, *qfprom_csel;
> > +
> > + qfprom_cdata = (u32 *)qfprom_read(priv->dev, "calib");
> > + if (IS_ERR(qfprom_cdata))
> > + return PTR_ERR(qfprom_cdata);
> > +
> > + qfprom_csel = (u32 *)qfprom_read(priv->dev, "calib_sel");
> > + if (IS_ERR(qfprom_csel)) {
> > + kfree(qfprom_cdata);
> > + return PTR_ERR(qfprom_csel);
> > + }
> > +
> > + mode = (qfprom_csel[0] & MSM8939_CAL_SEL_MASK) >> MSM8939_CAL_SEL_SHIFT;
> > + dev_dbg(priv->dev, "calibration mode is %d\n", mode);
>
> Add an extra line here.
>
> > + switch (mode) {
> > + case TWO_PT_CALIB:
> > + base1 = (qfprom_cdata[1] & MSM8939_BASE1_MASK) >> MSM8939_BASE1_SHIFT;
> > + p2[0] = (qfprom_cdata[0] & MSM8939_S0_P2_MASK) >> MSM8939_S0_P2_SHIFT;
> > + p2[1] = (qfprom_cdata[0] & MSM8939_S1_P2_MASK) >> MSM8939_S1_P2_SHIFT;
> > + p2[2] = (qfprom_cdata[1] & MSM8939_S2_P2_MASK) >> MSM8939_S2_P2_SHIFT;
> > + p2[3] = (qfprom_cdata[1] & MSM8939_S3_P2_MASK) >> MSM8939_S3_P2_SHIFT;
> > + p2[4] = (qfprom_cdata[1] & MSM8939_S4_P2_MASK) >> MSM8939_S4_P2_SHIFT;
> > + p2[5] = (qfprom_cdata[1] & MSM8939_S5_P2_MASK) >> MSM8939_S5_P2_SHIFT;
> > + p2[6] = (qfprom_cdata[1] & MSM8939_S6_P2_MASK) >> MSM8939_S6_P2_SHIFT;
> > + p2[7] = (qfprom_cdata[1] & MSM8939_S7_P2_MASK) >> MSM8939_S7_P2_SHIFT;
> > + p2[8] = (qfprom_cdata[1] & MSM8939_S8_P2_MASK) >> MSM8939_S8_P2_SHIFT;
> > + p2[9] = (qfprom_cdata[1] & MSM8939_S9_P2_MASK_0_4) >> MSM8939_S9_P2_SHIFT_0_4;
> > + p2[10] = (qfprom_cdata[1] & MSM8939_S9_P2_MASK_5) >> MSM8939_S9_P2_SHIFT_5;
> > + for (i = 0; i < priv->num_sensors; i++)
> > + p2[i] = ((base1 + p2[i]) << 3);
> > + /* Fall through */
> > + case ONE_PT_CALIB2:
> > + base0 = (qfprom_cdata[0] & MSM8939_BASE0_MASK);
> > + p1[0] = (qfprom_cdata[0] & MSM8939_S0_P1_MASK) >> MSM8939_S0_P1_SHIFT;
> > + p1[1] = (qfprom_cdata[0] & MSM8939_S1_P1_MASK) >> MSM8939_S1_P1_SHIFT;
> > + p1[2] = (qfprom_cdata[0] & MSM8939_S2_P1_MASK_0_4) >> MSM8939_S2_P1_SHIFT_0_4;
> > + p1[3] = (qfprom_cdata[0] & MSM8939_S2_P1_MASK_5) >> MSM8939_S2_P1_SHIFT_5;
> > + p1[4] = (qfprom_cdata[1] & MSM8939_S3_P1_MASK) >> MSM8939_S3_P1_SHIFT;
> > + p1[5] = (qfprom_cdata[1] & MSM8939_S4_P1_MASK) >> MSM8939_S4_P1_SHIFT;
> > + p1[6] = (qfprom_cdata[1] & MSM8939_S5_P1_MASK) >> MSM8939_S5_P1_SHIFT;
> > + p1[7] = (qfprom_cdata[1] & MSM8939_S6_P1_MASK) >> MSM8939_S6_P1_SHIFT;
> > + //yes, 7 is missing in downstream
>
> Use C comment style. Might this be a bug?
>
> > + p1[8] = (qfprom_cdata[1] & MSM8939_S8_P1_MASK) >> MSM8939_S8_P1_SHIFT;
> > + p1[9] = (qfprom_cdata[1] & MSM8939_S9_P1_MASK) >> MSM8939_S9_P1_SHIFT;
> > + for (i = 0; i < priv->num_sensors; i++)
> > + p1[i] = (((base0) + p1[i]) << 3);
> > + break;
> > + default:
> > + for (i = 0; i < priv->num_sensors; i++) {
> > + p1[i] = 500;
> > + p2[i] = 780;
> > + }
> > + break;
> > + }
> > +
> > + compute_intercept_slope(priv, p1, p2, mode);
> > + kfree(qfprom_cdata);
> > + kfree(qfprom_csel);
> > +
> > + return 0;
> > +}
> > +
> > static int calibrate_8974(struct tsens_priv *priv)
> > {
> > int base1 = 0, base2 = 0, i;
> > @@ -325,7 +450,7 @@ static int calibrate_8974(struct tsens_priv *priv)
> > return 0;
> > }
> >
> > -/* v0.1: 8916, 8974 */
> > +/* v0.1: 8916, 8939, 8974 */
> >
> > static struct tsens_features tsens_v0_1_feat = {
> > .ver_major = VER_0_1,
> > @@ -386,6 +511,21 @@ struct tsens_plat_data data_8916 = {
> > .fields = tsens_v0_1_regfields,
> > };
> >
> > +static const struct tsens_ops ops_8939 = {
> > + .init = init_common,
> > + .calibrate = calibrate_8939,
> > + .get_temp = get_temp_common,
> > +};
> > +
> > +struct tsens_plat_data data_8939 = {
> > + .num_sensors = 10,
>
> I think 8939 has 11 sensors. Can you confirm?
>
> > + .ops = &ops_8939,
> > + .hw_ids = (unsigned int []){0, 1, 2, 4, 5, 6, 7, 8, 9 },
>
> And this should be equal to the number of sensors
>
>
> > +
> > + .feat = &tsens_v0_1_feat,
> > + .fields = tsens_v0_1_regfields,
> > +};
> > +
> > static const struct tsens_ops ops_8974 = {
> > .init = init_common,
> > .calibrate = calibrate_8974,
> > diff --git a/drivers/thermal/qcom/tsens.c b/drivers/thermal/qcom/tsens.c
> > index 2f77d235cf735..f654057e96ae1 100644
> > --- a/drivers/thermal/qcom/tsens.c
> > +++ b/drivers/thermal/qcom/tsens.c
> > @@ -59,6 +59,9 @@ static const struct of_device_id tsens_table[] = {
> > {
> > .compatible = "qcom,msm8916-tsens",
> > .data = &data_8916,
> > + }, {
> > + .compatible = "qcom,msm8939-tsens",
> > + .data = &data_8939,
> > }, {
> > .compatible = "qcom,msm8974-tsens",
> > .data = &data_8974,
> > diff --git a/drivers/thermal/qcom/tsens.h b/drivers/thermal/qcom/tsens.h
> > index 502acf0e68285..403b15546f648 100644
> > --- a/drivers/thermal/qcom/tsens.h
> > +++ b/drivers/thermal/qcom/tsens.h
> > @@ -590,7 +590,7 @@ irqreturn_t tsens_critical_irq_thread(int irq, void *data);
> > extern struct tsens_plat_data data_8960;
> >
> > /* TSENS v0.1 targets */
> > -extern struct tsens_plat_data data_8916, data_8974;
> > +extern struct tsens_plat_data data_8916, data_8939, data_8974;
> >
> > /* TSENS v1 targets */
> > extern struct tsens_plat_data data_tsens_v1, data_8976;
> > --
> > 2.26.1
> >
next prev parent reply other threads:[~2020-05-04 8:04 UTC|newest]
Thread overview: 9+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-05-01 20:33 [PATCH 0/2] Add msm8939 tsensv0_1 support Konrad Dybcio
2020-05-01 20:33 ` [PATCH 1/2] thermal: qcom: tsens-v0_1: Add support for MSM8939 Konrad Dybcio
2020-05-04 6:31 ` Amit Kucheria
2020-05-04 8:04 ` Konrad Dybcio [this message]
2020-06-28 7:39 ` Shawn Guo
2020-06-28 8:02 ` Konrad Dybcio
2020-05-01 20:33 ` [PATCH 2/2] dt-bindings: tsens: qcom: Document MSM8939 compatible Konrad Dybcio
2020-05-04 6:28 ` Amit Kucheria
2020-05-04 19:51 ` Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=CAMS8qEXAPTcCYTKSA1VYnHtqT1zuUdYNNskRfgPiFykdKdqsKA@mail.gmail.com \
--to=konradybcio@gmail.com \
--cc=agross@kernel.org \
--cc=amit.kucheria@linaro.org \
--cc=bjorn.andersson@linaro.org \
--cc=daniel.lezcano@linaro.org \
--cc=devicetree@vger.kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=robh+dt@kernel.org \
--cc=rui.zhang@intel.com \
--cc=skrzynka@konradybcio.pl \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).