Hello Paul, On Mon, Aug 12, 2019 at 10:43:10PM +0200, Paul Cercueil wrote:Le lun. 12 août 2019 à 8:15, Uwe =?iso-8859-1?q?Kleine-K=F6nig?= <u.kleine-koenig@pengutronix.de> a écrit : > On Fri, Aug 09, 2019 at 07:14:45PM +0200, Paul Cercueil wrote: > > Le ven. 9 août 2019 à 19:05, Uwe =?iso-8859-1?q?Kleine-K=F6nig?= > > <u.kleine-koenig@pengutronix.de> a écrit : > > > On Fri, Aug 09, 2019 at 02:30:28PM +0200, Paul Cercueil wrote: > > > > [...] > > > > + /* Reset the clock to the maximum rate, and we'll reduce it if needed */ > > > > + ret = clk_set_max_rate(clk, parent_rate); > > > > > > What is the purpose of this call? IIUC this limits the allowed range of > > > rates for clk. I assume the idea is to prevent other consumers to change > > > the rate in a way that makes it unsuitable for this pwm. But this only > > > makes sense if you had a notifier for clk changes, doesn't it? I'm > > > confused. > > > > Nothing like that. The second call to clk_set_max_rate() might have set > > a maximum clock rate that's lower than the parent's rate, and we want to > > undo that. > > I still don't get the purpose of this call. Why do you limit the clock > rate at all? As it says below, we "limit the clock to a maximum rate that still gives us a period value which fits in 16 bits". So that the computed hardware values won't overflow.But why not just using clk_set_rate? You want to have the clock running at a certain rate, not any rate below that certain rate, don't you?
E.g. if at a rate of 12 MHz your computed hardware value for the period is 0xf000, then at a rate of 24 MHz it won't fit in 16 bits. So the clock rate must be reduced to the highest possible that will still give you a < 16-bit value. We always want the highest possible clock rate that works, for the sake of precision.This is dubious; but ok to keep the driver simple. (Consider a PWM that can run at i MHz for i in [1, .. 30]. If a period of 120 ns and a duty cycle of 40 ns is requested you can get an exact match with 25 MHz, but not with 30 MHz.)
> > Basically, we start from the maximum clock rate we can get for that PWM > > - which is the rate of the parent clk - and from that compute the maximum > > clock rate that we can support that still gives us < 16-bits hardware > > values for the period and duty. > > > > We then pass that computed maximum clock rate to clk_set_max_rate(), which > > may or may not update the current PWM clock's rate to match the new limits. > > Finally we read back the PWM clock's rate and compute the period and duty > > from that. > > If you change the clk rate, is this externally visible on the PWM > output? Does this affect other PWM instances? The clock rate doesn't change the PWM output because the hardware values for the period and duty are adapted accordingly to reflect the change.It doesn't change it in the end. But in the (short) time frame between the call to change the clock and the update of the PWM registers there is a glitch, right?
You didn't answer to the question about other PWM instances. Does that mean others are not affected?
Best regards Uwe PS: It would be great if you could fix your mailer to not damage the quoted mail. Also it doesn't seem to understand how my name is encoded in the From line. I fixed up the quotes in my reply.
--Pengutronix e.K. | Uwe Kleine-König | Industrial Linux Solutions | http://www.pengutronix.de/ |