From mboxrd@z Thu Jan 1 00:00:00 1970 Return-Path: From: Fabien Dessenne Subject: [PATCH v3 2/8] dt-bindings: remoteproc: add bindings for stm32 remote processor driver Date: Thu, 2 May 2019 10:10:00 +0200 Message-ID: <1556784606-3016-3-git-send-email-fabien.dessenne@st.com> In-Reply-To: <1556784606-3016-1-git-send-email-fabien.dessenne@st.com> References: <1556784606-3016-1-git-send-email-fabien.dessenne@st.com> MIME-Version: 1.0 Content-Type: text/plain To: Rob Herring , Mark Rutland , Maxime Coquelin , Alexandre Torgue , Ohad Ben-Cohen , Bjorn Andersson , devicetree@vger.kernel.org, linux-stm32@st-md-mailman.stormreply.com, linux-arm-kernel@lists.infradead.org, linux-kernel@vger.kernel.org, linux-remoteproc@vger.kernel.org Cc: Fabien Dessenne , Loic Pallardy , Arnaud Pouliquen , "Ludovic Barre , Benjamin Gaignard" List-ID: Add the device tree bindings document for the stm32 remoteproc devices. Signed-off-by: Fabien Dessenne --- .../devicetree/bindings/remoteproc/stm32-rproc.txt | 63 ++++++++++++++++++++++ 1 file changed, 63 insertions(+) create mode 100644 Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt diff --git a/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt new file mode 100644 index 0000000..a495757 --- /dev/null +++ b/Documentation/devicetree/bindings/remoteproc/stm32-rproc.txt @@ -0,0 +1,63 @@ +STMicroelectronics STM32 Remoteproc +----------------------------------- +This document defines the binding for the remoteproc component that loads and +boots firmwares on the ST32MP family chipset. + +Required properties: +- compatible: Must be "st,stm32mp1-m4" +- reg: Address ranges of the RETRAM and MCU SRAM memories used by the + remote processor. +- resets: Reference to a reset controller asserting the remote processor. +- st,syscfg-holdboot: Reference to the system configuration which holds the + remote processor reset hold boot + 1st cell: phandle of syscon block + 2nd cell: register offset containing the hold boot setting + 3rd cell: register bitmask for the hold boot field +- st,syscfg-tz: Reference to the system configuration which holds the RCC trust + zone mode + 1st cell: phandle to syscon block + 2nd cell: register offset containing the RCC trust zone mode setting + 3rd cell: register bitmask for the RCC trust zone mode bit + +Optional properties: +- interrupts: Should contain the watchdog interrupt +- mboxes: This property is required only if the rpmsg/virtio functionality + is used. List of phandle and mailbox channel specifiers: + - a channel (a) used to communicate through virtqueues with the + remote proc. + Bi-directional channel: + - from local to remote = send message + - from remote to local = send message ack + - a channel (b) working the opposite direction of channel (a) + - a channel (c) used by the local proc to notify the remote proc + that it is about to be shut down. + Unidirectional channel: + - from local to remote, where ACK from the remote means + that it is ready for shutdown +- mbox-names: This property is required if the mboxes property is used. + - must be "vq0" for channel (a) + - must be "vq1" for channel (b) + - must be "shutdown" for channel (c) +- memory-region: List of phandles to the reserved memory regions associated with + the remoteproc device. This is variable and describes the + memories shared with the remote processor (eg: remoteproc + firmware and carveouts, rpmsg vrings, ...). + (see ../reserved-memory/reserved-memory.txt) +- st,syscfg-pdds: Reference to the system configuration which holds the remote + processor deep sleep setting + 1st cell: phandle to syscon block + 2nd cell: register offset containing the deep sleep setting + 3rd cell: register bitmask for the deep sleep bit +- st,auto_boot: If defined, when remoteproc is probed, it loads the default + firmware and starts the remote processor. + +Example: + m4_rproc: m4@38000000 { + compatible = "st,stm32mp1-m4"; + reg = <0x00000000 0x10000>, + <0x10000000 0x40000>, + <0x30000000 0x40000>; + resets = <&rcc MCU_R>; + st,syscfg-holdboot = <&rcc 0x10C 0x1>; + st,syscfg-tz = <&rcc 0x000 0x1>; + }; -- 2.7.4