From: Michael Auchter <michael.auchter@ni.com>
To: Ben Levinsky <ben.levinsky@xilinx.com>
Cc: stefanos@xilinx.com, michals@xilinx.com,
devicetree@vger.kernel.org, mathieu.poirier@linaro.org,
ed.mooring@xilinx.com, linux-remoteproc@vger.kernel.org,
linux-kernel@vger.kernel.org, wendy.liang@xilinx.com,
robh+dt@kernel.org, linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v8 3/5] firmware: xilinx: Add RPU configuration APIs
Date: Tue, 25 Aug 2020 15:59:56 -0500 [thread overview]
Message-ID: <20200825205956.GA12885@xaphan> (raw)
In-Reply-To: <20200811033213.20088-4-ben.levinsky@xilinx.com>
Hey Ben,
On Mon, Aug 10, 2020 at 08:32:11PM -0700, Ben Levinsky wrote:
> This patch adds APIs to provide access and a configuration interface
> to the current power state of a sub-system on Zynqmp sub-system.
>
> Signed-off-by: Ben Levinsky <ben.levinsky@xilinx.com>
> ---
> v3:
> - add xilinx-related platform mgmt fn's instead of wrapping around
> function pointer in xilinx eemi ops struct
> v4:
> - add default values for enums
> ---
> drivers/firmware/xilinx/zynqmp.c | 99 ++++++++++++++++++++++++++++
> include/linux/firmware/xlnx-zynqmp.h | 34 ++++++++++
> 2 files changed, 133 insertions(+)
>
> diff --git a/drivers/firmware/xilinx/zynqmp.c b/drivers/firmware/xilinx/zynqmp.c
> index f1a0bd35deeb..fdd61d258e55 100644
> --- a/drivers/firmware/xilinx/zynqmp.c
> +++ b/drivers/firmware/xilinx/zynqmp.c
> @@ -846,6 +846,61 @@ int zynqmp_pm_release_node(const u32 node)
> }
> EXPORT_SYMBOL_GPL(zynqmp_pm_release_node);
>
> +/**
> + * zynqmp_pm_get_rpu_mode() - Get RPU mode
> + * @node_id: Node ID of the device
> + * @arg1: Argument 1 to requested IOCTL call
> + * @arg2: Argument 2 to requested IOCTL call
> + * @out: Returned output value
> + *
> + * Return: RPU mode
> + */
> +int zynqmp_pm_get_rpu_mode(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out)
> +{
> + return zynqmp_pm_invoke_fn(PM_IOCTL, node_id,
> + IOCTL_GET_RPU_OPER_MODE, 0, 0, out);
> +}
> +EXPORT_SYMBOL_GPL(zynqmp_pm_get_rpu_mode);
> +
> +/**
> + * zynqmp_pm_set_rpu_mode() - Set RPU mode
> + * @node_id: Node ID of the device
> + * @ioctl_id: ID of the requested IOCTL
> + * @arg2: Argument 2 to requested IOCTL call
> + * @out: Returned output value
> + *
> + * This function is used to set RPU mode.
> + *
> + * Return: Returns status, either success or error+reason
> + */
> +int zynqmp_pm_set_rpu_mode(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out)
> +{
> + return zynqmp_pm_invoke_fn(PM_IOCTL, node_id,
> + IOCTL_SET_RPU_OPER_MODE, 0, 0, out);
This should pass through arg1 instead of 0 for the argument after
IOCTL_SET_RPU_OPER_MODE. As this is, the RPU will always be configured
in lockstep mode regardless of a request to switch to split mode.
Also, the kerneldoc for these functions could use some love (ioctl_id no
longer exists, arg1 isn't documented, arg2 is documented by very
non-specifically).
> +}
> +EXPORT_SYMBOL_GPL(zynqmp_pm_set_rpu_mode);
> +
> +/**
> + * zynqmp_pm_tcm_comb_config - configure TCM
> + * @node_id: Node ID of the device
> + * @arg1: Argument 1 to requested IOCTL call
> + * @arg2: Argument 2 to requested IOCTL call
> + * @out: Returned output value
> + *
> + * This function is used to set RPU mode.
> + *
> + * Return: Returns status, either success or error+reason
> + */
> +int zynqmp_pm_set_tcm_config(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out)
> +{
> + return zynqmp_pm_invoke_fn(PM_IOCTL, node_id,
> + IOCTL_TCM_COMB_CONFIG, 0, 0, out);
> +}
> +EXPORT_SYMBOL_GPL(zynqmp_pm_set_tcm_config);
> +
> /**
> * zynqmp_pm_force_powerdown - PM call to request for another PU or subsystem to
> * be powered down forcefully
> @@ -881,6 +936,50 @@ int zynqmp_pm_request_wakeup(const u32 node,
> }
> EXPORT_SYMBOL_GPL(zynqmp_pm_request_wakeup);
>
> +/**
> + * zynqmp_pm_get_node_status - PM call to request a node's current power state
> + * @node: ID of the component or sub-system in question
> + * @status: Current operating state of the requested node
> + * @requirements: Current requirements asserted on the node,
> + * used for slave nodes only.
> + * @usage: Usage information, used for slave nodes only:
> + * PM_USAGE_NO_MASTER - No master is currently using
> + * the node
> + * PM_USAGE_CURRENT_MASTER - Only requesting master is
> + * currently using the node
> + * PM_USAGE_OTHER_MASTER - Only other masters are
> + * currently using the node
> + * PM_USAGE_BOTH_MASTERS - Both the current and at least
> + * one other master is currently
> + * using the node
> + *
> + * Return: status, either success or error+reason
> + */
> +int zynqmp_pm_get_node_status(const u32 node,
> + u32 *status, u32 *requirements,
> + u32 *usage)
> +
> +{
> + u32 ret_payload[PAYLOAD_ARG_CNT];
> + int ret;
> +
> + if (!status)
> + return -EINVAL;
> +
> + ret = zynqmp_pm_invoke_fn(PM_GET_NODE_STATUS, node, 0, 0, 0,
> + ret_payload);
> + if (ret_payload[0] == XST_PM_SUCCESS) {
> + *status = ret_payload[1];
> + if (requirements)
> + *requirements = ret_payload[2];
> + if (usage)
> + *usage = ret_payload[3];
> + }
> +
> + return ret;
> +}
> +EXPORT_SYMBOL_GPL(zynqmp_pm_get_node_status);
> +
> /**
> * zynqmp_pm_set_requirement() - PM call to set requirement for PM slaves
> * @node: Node ID of the slave
> diff --git a/include/linux/firmware/xlnx-zynqmp.h b/include/linux/firmware/xlnx-zynqmp.h
> index 4d83a7d69c4c..0caca9e2223a 100644
> --- a/include/linux/firmware/xlnx-zynqmp.h
> +++ b/include/linux/firmware/xlnx-zynqmp.h
> @@ -64,6 +64,7 @@
>
> enum pm_api_id {
> PM_GET_API_VERSION = 1,
> + PM_GET_NODE_STATUS = 3,
> PM_FORCE_POWERDOWN = 8,
> PM_REQUEST_WAKEUP = 10,
> PM_SYSTEM_SHUTDOWN = 12,
> @@ -384,6 +385,14 @@ int zynqmp_pm_request_wakeup(const u32 node,
> const bool set_addr,
> const u64 address,
> const enum zynqmp_pm_request_ack ack);
> +int zynqmp_pm_get_node_status(const u32 node, u32 *status,
> + u32 *requirements, u32 *usage);
> +int zynqmp_pm_get_rpu_mode(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out);
> +int zynqmp_pm_set_rpu_mode(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out);
> +int zynqmp_pm_set_tcm_config(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out);
> #else
> static inline struct zynqmp_eemi_ops *zynqmp_pm_get_eemi_ops(void)
> {
> @@ -548,6 +557,31 @@ static inline int zynqmp_pm_request_wakeup(const u32 node,
> {
> return -ENODEV;
> }
> +
> +static inline int zynqmp_pm_get_node_status(const u32 node,
> + u32 *status, u32 *requirements,
> + u32 *usage)
> +{
> + return -ENODEV;
> +}
> +
> +static inline int zynqmp_pm_get_rpu_mode(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out)
> +{
> + return -ENODEV;
> +}
> +
> +static inline int zynqmp_pm_set_rpu_mode(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out)
> +{
> + return -ENODEV;
> +}
> +
> +static inline int zynqmp_pm_set_tcm_config(u32 node_id,
> + u32 arg1, u32 arg2, u32 *out)
> +{
> + return -ENODEV;
> +}
> #endif
>
> #endif /* __FIRMWARE_ZYNQMP_H__ */
> --
> 2.17.1
>
Thanks,
Michael
next prev parent reply other threads:[~2020-08-25 22:09 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-08-11 3:32 [PATCH v8 0/5] Provide basic driver to control Arm R5 co-processor found on Xilinx ZynqMP Ben Levinsky
2020-08-11 3:32 ` [PATCH v8 1/5] firmware: xilinx: Add ZynqMP firmware ioctl enums for RPU configuration Ben Levinsky
2020-08-11 3:32 ` [PATCH v8 2/5] firmware: xilinx: Add shutdown/wakeup APIs Ben Levinsky
2020-08-13 20:35 ` Stefano Stabellini
2020-08-18 14:24 ` Ben Levinsky
2020-08-24 23:34 ` Ben Levinsky
2020-08-25 0:30 ` Stefano Stabellini
2020-08-11 3:32 ` [PATCH v8 3/5] firmware: xilinx: Add RPU configuration APIs Ben Levinsky
2020-08-13 20:35 ` Stefano Stabellini
2020-08-18 14:26 ` Ben Levinsky
2020-08-25 20:59 ` Michael Auchter [this message]
2020-08-11 3:32 ` [PATCH v8 4/5] dt-bindings: remoteproc: Add documentation for ZynqMP R5 rproc bindings Ben Levinsky
2020-08-11 3:32 ` [PATCH v8 5/5] remoteproc: Add initial zynqmp R5 remoteproc driver Ben Levinsky
2020-08-13 20:35 ` Stefano Stabellini
2020-08-18 14:56 ` Ben Levinsky
2020-08-19 21:21 ` Stefano Stabellini
2020-08-20 15:13 ` Ben Levinsky
2020-08-24 21:19 ` Ben Levinsky
2020-08-25 21:09 ` Michael Auchter
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200825205956.GA12885@xaphan \
--to=michael.auchter@ni.com \
--cc=ben.levinsky@xilinx.com \
--cc=devicetree@vger.kernel.org \
--cc=ed.mooring@xilinx.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-remoteproc@vger.kernel.org \
--cc=mathieu.poirier@linaro.org \
--cc=michals@xilinx.com \
--cc=robh+dt@kernel.org \
--cc=stefanos@xilinx.com \
--cc=wendy.liang@xilinx.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).