Linux-remoteproc Archive on lore.kernel.org
 help / color / Atom feed
From: Arnaud POULIQUEN <arnaud.pouliquen@foss.st.com>
To: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Ohad Ben-Cohen <ohad@wizery.com>,
	Mathieu Poirier <mathieu.poirier@linaro.org>,
	Rob Herring <robh@kernel.org>,
	Alexandre Torgue <alexandre.torgue@foss.st.com>,
	<devicetree@vger.kernel.org>,
	<linux-stm32@st-md-mailman.stormreply.com>,
	<linux-arm-kernel@lists.infradead.org>,
	<linux-remoteproc@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v4 2/2] remoteproc: stm32: add capability to detach
Date: Wed, 14 Apr 2021 09:23:56 +0200
Message-ID: <3df5317b-d28a-9362-6876-99442fdb8ef5@foss.st.com> (raw)
In-Reply-To: <YHYOd/vqeZCiqkpJ@builder.lan>

Hello Bjorn

On 4/13/21 11:34 PM, Bjorn Andersson wrote:
> On Wed 31 Mar 02:33 CDT 2021, Arnaud Pouliquen wrote:
> 
>> A mechanism similar to the shutdown mailbox signal is implemented to
>> detach a remote processor.
>>
>> Upon detachment, a signal is sent to the remote firmware, allowing it
>> to perform specific actions such as stopping rpmsg communication.
>>
>> The Cortex-M hold boot is also disabled to allow the remote processor
>> to restart in case of crash.
>>
>> Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
>> Reviewed-by: Mathieu Poirier <mathieu.poirier@linaro.org>
>> Tested-by: Mathieu Poirier <mathieu.poirier@linaro.org>
>> ---
>>  drivers/remoteproc/stm32_rproc.c | 39 ++++++++++++++++++++++++++++++--
>>  1 file changed, 37 insertions(+), 2 deletions(-)
>>
>> diff --git a/drivers/remoteproc/stm32_rproc.c b/drivers/remoteproc/stm32_rproc.c
>> index 3d45f51de4d0..7353f9e7e7af 100644
>> --- a/drivers/remoteproc/stm32_rproc.c
>> +++ b/drivers/remoteproc/stm32_rproc.c
>> @@ -28,7 +28,7 @@
>>  #define RELEASE_BOOT		1
>>  
>>  #define MBOX_NB_VQ		2
>> -#define MBOX_NB_MBX		3
>> +#define MBOX_NB_MBX		4
>>  
>>  #define STM32_SMC_RCC		0x82001000
>>  #define STM32_SMC_REG_WRITE	0x1
>> @@ -38,6 +38,7 @@
>>  #define STM32_MBX_VQ1		"vq1"
>>  #define STM32_MBX_VQ1_ID	1
>>  #define STM32_MBX_SHUTDOWN	"shutdown"
>> +#define STM32_MBX_DETACH	"detach"
>>  
>>  #define RSC_TBL_SIZE		1024
>>  
>> @@ -336,6 +337,15 @@ static const struct stm32_mbox stm32_rproc_mbox[MBOX_NB_MBX] = {
>>  			.tx_done = NULL,
>>  			.tx_tout = 500, /* 500 ms time out */
>>  		},
>> +	},
>> +	{
>> +		.name = STM32_MBX_DETACH,
>> +		.vq_id = -1,
>> +		.client = {
>> +			.tx_block = true,
>> +			.tx_done = NULL,
>> +			.tx_tout = 200, /* 200 ms time out to detach should be fair enough */
>> +		},
>>  	}
>>  };
>>  
>> @@ -461,6 +471,25 @@ static int stm32_rproc_attach(struct rproc *rproc)
>>  	return stm32_rproc_set_hold_boot(rproc, true);
>>  }
>>  
>> +static int stm32_rproc_detach(struct rproc *rproc)
>> +{
>> +	struct stm32_rproc *ddata = rproc->priv;
>> +	int err, dummy_data, idx;
>> +
>> +	/* Inform the remote processor of the detach */
>> +	idx = stm32_rproc_mbox_idx(rproc, STM32_MBX_DETACH);
>> +	if (idx >= 0 && ddata->mb[idx].chan) {
>> +		/* A dummy data is sent to allow to block on transmit */
>> +		err = mbox_send_message(ddata->mb[idx].chan,
>> +					&dummy_data);
> 
> Seems I posted my comment on v1, rather than this latest version. Please
> let me know if we should do anything about this dummy_data.

Thanks for pointing this out, you are right, the mailbox driver is stm32_ipcc
and it only sends a signal to the remote processor.

As message can be queued by the mailbox framework using a local variable seems
not a good option. As this code is a copy/past of the kick and stop?
I propose to get this one and I will send a new patch to fix the usage in the
whole driver.

Thanks,
Arnaud

> 
> Regards,
> Bjorn
> 
>> +		if (err < 0)
>> +			dev_warn(&rproc->dev, "warning: remote FW detach without ack\n");
>> +	}
>> +
>> +	/* Allow remote processor to auto-reboot */
>> +	return stm32_rproc_set_hold_boot(rproc, false);
>> +}
>> +
>>  static int stm32_rproc_stop(struct rproc *rproc)
>>  {
>>  	struct stm32_rproc *ddata = rproc->priv;
>> @@ -597,7 +626,12 @@ stm32_rproc_get_loaded_rsc_table(struct rproc *rproc, size_t *table_sz)
>>  	}
>>  
>>  done:
>> -	/* Assuming the resource table fits in 1kB is fair */
>> +	/*
>> +	 * Assuming the resource table fits in 1kB is fair.
>> +	 * Notice for the detach, that this 1 kB memory area has to be reserved in the coprocessor
>> +	 * firmware for the resource table. On detach, the remoteproc core re-initializes this
>> +	 * entire area by overwriting it with the initial values stored in rproc->clean_table.
>> +	 */
>>  	*table_sz = RSC_TBL_SIZE;
>>  	return (struct resource_table *)ddata->rsc_va;
>>  }
>> @@ -607,6 +641,7 @@ static const struct rproc_ops st_rproc_ops = {
>>  	.start		= stm32_rproc_start,
>>  	.stop		= stm32_rproc_stop,
>>  	.attach		= stm32_rproc_attach,
>> +	.detach		= stm32_rproc_detach,
>>  	.kick		= stm32_rproc_kick,
>>  	.load		= rproc_elf_load_segments,
>>  	.parse_fw	= stm32_rproc_parse_fw,
>> -- 
>> 2.17.1
>>

  reply index

Thread overview: 7+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2021-03-31  7:33 [PATCH v4 0/2] remoteproc: stm32: add support of detaching a remote processor Arnaud Pouliquen
2021-03-31  7:33 ` [PATCH v4 1/2] dt-bindings: remoteproc: stm32-rproc: add new mailbox channel for detach Arnaud Pouliquen
2021-03-31  7:33 ` [PATCH v4 2/2] remoteproc: stm32: add capability to detach Arnaud Pouliquen
2021-04-13 21:34   ` Bjorn Andersson
2021-04-14  7:23     ` Arnaud POULIQUEN [this message]
2021-04-14 15:01       ` Bjorn Andersson
2021-04-14 15:10 ` [PATCH v4 0/2] remoteproc: stm32: add support of detaching a remote processor patchwork-bot+linux-remoteproc

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=3df5317b-d28a-9362-6876-99442fdb8ef5@foss.st.com \
    --to=arnaud.pouliquen@foss.st.com \
    --cc=alexandre.torgue@foss.st.com \
    --cc=bjorn.andersson@linaro.org \
    --cc=devicetree@vger.kernel.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-remoteproc@vger.kernel.org \
    --cc=linux-stm32@st-md-mailman.stormreply.com \
    --cc=mathieu.poirier@linaro.org \
    --cc=ohad@wizery.com \
    --cc=robh@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-remoteproc Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-remoteproc/0 linux-remoteproc/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-remoteproc linux-remoteproc/ https://lore.kernel.org/linux-remoteproc \
		linux-remoteproc@vger.kernel.org
	public-inbox-index linux-remoteproc

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-remoteproc


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git