From: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
To: "Hans Verkuil" <hverkuil@xs4all.nl>,
"Koji Matsuoka" <koji.matsuoka.xm@renesas.com>,
"Jacopo Mondi" <jacopo@jmondi.org>,
"Laurent Pinchart" <laurent.pinchart@ideasonboard.com>,
"Niklas Söderlund" <niklas.soderlund@ragnatech.se>,
"Steve Longerbeam" <steve_longerbeam@mentor.com>
Cc: linux-renesas-soc@vger.kernel.org, linux-media@vger.kernel.org
Subject: Re: [PATCH 1/2] media: i2c: adv748x: Convert SW reset routine to function
Date: Fri, 18 Jan 2019 13:34:01 +0000 [thread overview]
Message-ID: <12e24971-e5e7-dc80-ebfc-8e789d114ddb@ideasonboard.com> (raw)
In-Reply-To: <9d32186f-1024-d014-0123-d8e6a944ee12@xs4all.nl>
Hi Hans,
On 18/01/2019 12:09, Hans Verkuil wrote:
> On 1/11/19 6:41 PM, Kieran Bingham wrote:
>> The ADV748x is currently reset by writting a small table of registers to
>> the device.
s/writting/writing/
>>
>> The table lacks documentation and contains magic values to perform the
>> actions, including using a fake register address to introduce a delay
>> loop.
>>
>> Remove the table, and convert to code, documenting the purpose of the
>> specific writes along the way.
>>
>> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
>
> Hmm, this patch doesn't apply to the master branch.
>
> Does it depend on other patches being merged first, or it is just out-of-date?
Hi Hans,
Sorry - I should have specified - They are dependant upon Jacopo's series.
--
Kieran
>
> Regards,
>
> Hans
>
>> ---
>> drivers/media/i2c/adv748x/adv748x-core.c | 32 ++++++++++++++++--------
>> drivers/media/i2c/adv748x/adv748x.h | 16 ++++++++++++
>> 2 files changed, 38 insertions(+), 10 deletions(-)
>>
>> diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c
>> index 02f9c440301c..252bdb28b18b 100644
>> --- a/drivers/media/i2c/adv748x/adv748x-core.c
>> +++ b/drivers/media/i2c/adv748x/adv748x-core.c
>> @@ -389,15 +389,6 @@ static const struct media_entity_operations adv748x_media_ops = {
>> * HW setup
>> */
>>
>> -static const struct adv748x_reg_value adv748x_sw_reset[] = {
>> -
>> - {ADV748X_PAGE_IO, 0xff, 0xff}, /* SW reset */
>> - {ADV748X_PAGE_WAIT, 0x00, 0x05},/* delay 5 */
>> - {ADV748X_PAGE_IO, 0x01, 0x76}, /* ADI Required Write */
>> - {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */
>> - {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */
>> -};
>> -
>> /* Initialize CP Core with RGB888 format. */
>> static const struct adv748x_reg_value adv748x_init_hdmi[] = {
>> /* Disable chip powerdown & Enable HDMI Rx block */
>> @@ -474,12 +465,33 @@ static const struct adv748x_reg_value adv748x_init_afe[] = {
>> {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */
>> };
>>
>> +static int adv748x_sw_reset(struct adv748x_state *state)
>> +{
>> + int ret;
>> +
>> + ret = io_write(state, ADV748X_IO_REG_FF, ADV748X_IO_REG_FF_MAIN_RESET);
>> + if (ret)
>> + return ret;
>> +
>> + usleep_range(5000, 6000);
>> +
>> + /* Disable CEC Wakeup from power-down mode */
>> + ret = io_clrset(state, ADV748X_IO_REG_01, ADV748X_IO_REG_01_PWRDN_MASK,
>> + ADV748X_IO_REG_01_PWRDNB);
>> + if (ret)
>> + return ret;
>> +
>> + /* Enable I2C Read Auto-Increment for consecutive reads */
>> + return io_write(state, ADV748X_IO_REG_F2,
>> + ADV748X_IO_REG_F2_READ_AUTO_INC);
>> +}
>> +
>> static int adv748x_reset(struct adv748x_state *state)
>> {
>> int ret;
>> u8 regval = 0;
>>
>> - ret = adv748x_write_regs(state, adv748x_sw_reset);
>> + ret = adv748x_sw_reset(state);
>> if (ret < 0)
>> return ret;
>>
>> diff --git a/drivers/media/i2c/adv748x/adv748x.h b/drivers/media/i2c/adv748x/adv748x.h
>> index b00c1995efb0..2f8d751cfbb0 100644
>> --- a/drivers/media/i2c/adv748x/adv748x.h
>> +++ b/drivers/media/i2c/adv748x/adv748x.h
>> @@ -211,6 +211,11 @@ struct adv748x_state {
>> #define ADV748X_IO_PD 0x00 /* power down controls */
>> #define ADV748X_IO_PD_RX_EN BIT(6)
>>
>> +#define ADV748X_IO_REG_01 0x01 /* pwrdn{2}b, prog_xtal_freq */
>> +#define ADV748X_IO_REG_01_PWRDN_MASK (BIT(7) | BIT(6))
>> +#define ADV748X_IO_REG_01_PWRDN2B BIT(7) /* CEC Wakeup Support */
>> +#define ADV748X_IO_REG_01_PWRDNB BIT(6) /* CEC Wakeup Support */
>> +
>> #define ADV748X_IO_REG_04 0x04
>> #define ADV748X_IO_REG_04_FORCE_FR BIT(0) /* Force CP free-run */
>>
>> @@ -229,8 +234,19 @@ struct adv748x_state {
>> #define ADV748X_IO_CHIP_REV_ID_1 0xdf
>> #define ADV748X_IO_CHIP_REV_ID_2 0xe0
>>
>> +#define ADV748X_IO_REG_F2 0xf2
>> +#define ADV748X_IO_REG_F2_READ_AUTO_INC BIT(0)
>> +
>> +/* For PAGE slave address offsets */
>> #define ADV748X_IO_SLAVE_ADDR_BASE 0xf2
>>
>> +/*
>> + * The ADV748x_Recommended_Settings_PrA_2014-08-20.pdf details both 0x80 and
>> + * 0xff as examples for performing a software reset.
>> + */
>> +#define ADV748X_IO_REG_FF 0xff
>> +#define ADV748X_IO_REG_FF_MAIN_RESET 0xff
>> +
>> /* HDMI RX Map */
>> #define ADV748X_HDMI_LW1 0x07 /* line width_1 */
>> #define ADV748X_HDMI_LW1_VERT_FILTER BIT(7)
>>
>
next prev parent reply other threads:[~2019-01-18 13:34 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-11 17:41 [PATCH 0/2] media: i2c: adv748x: Refactor sw_reset handling Kieran Bingham
2019-01-11 17:41 ` [PATCH 1/2] media: i2c: adv748x: Convert SW reset routine to function Kieran Bingham
2019-01-11 20:15 ` Laurent Pinchart
2019-01-12 16:50 ` Kieran Bingham
2019-01-18 12:26 ` Laurent Pinchart
2019-01-14 14:43 ` Niklas Söderlund
2019-01-18 12:09 ` Hans Verkuil
2019-01-18 13:34 ` Kieran Bingham [this message]
2019-01-11 17:41 ` [PATCH 2/2] media: i2c: adv748x: Remove PAGE_WAIT Kieran Bingham
2019-01-11 20:23 ` Laurent Pinchart
2019-01-12 16:51 ` Kieran Bingham
2019-01-14 14:44 ` Niklas Söderlund
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=12e24971-e5e7-dc80-ebfc-8e789d114ddb@ideasonboard.com \
--to=kieran.bingham+renesas@ideasonboard.com \
--cc=hverkuil@xs4all.nl \
--cc=jacopo@jmondi.org \
--cc=koji.matsuoka.xm@renesas.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=niklas.soderlund@ragnatech.se \
--cc=steve_longerbeam@mentor.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).