* [PATCH 0/2] Add LVDS panel support to HiHope RZ/G2M
@ 2019-08-29 10:21 Fabrizio Castro
2019-08-29 10:21 ` [PATCH 1/2] dt-bindings: display: Add idk-1110wr binding Fabrizio Castro
2019-08-29 10:21 ` [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display Fabrizio Castro
0 siblings, 2 replies; 5+ messages in thread
From: Fabrizio Castro @ 2019-08-29 10:21 UTC (permalink / raw)
To: Geert Uytterhoeven, Laurent Pinchart, Thierry Reding,
David Airlie, Daniel Vetter, Rob Herring, Mark Rutland
Cc: Fabrizio Castro, Sam Ravnborg, Simon Horman, Magnus Damm,
dri-devel, devicetree, linux-renesas-soc, linux-kernel,
Chris Paterson, Biju Das, Kieran Bingham, Jacopo Mondi,
xu_shunji, ebiharaml
Dear All,
the HiHope RZ/G2M is advertised as supporting panel idk-1110wr from
Advantech, but the panel doesn't come with the board, it has to purchased
separatey, therefore this series adds panel support to a new DT.
Thanks,
Fab
Fabrizio Castro (2):
dt-bindings: display: Add idk-1110wr binding
arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
.../display/panel/advantech,idk-1110wr.yaml | 69 +++++++++++++++++
arch/arm64/boot/dts/renesas/Makefile | 1 +
.../r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts | 86 ++++++++++++++++++++++
3 files changed, 156 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/advantech,idk-1110wr.yaml
create mode 100644 arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
--
2.7.4
^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH 1/2] dt-bindings: display: Add idk-1110wr binding
2019-08-29 10:21 [PATCH 0/2] Add LVDS panel support to HiHope RZ/G2M Fabrizio Castro
@ 2019-08-29 10:21 ` Fabrizio Castro
2019-08-29 10:21 ` [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display Fabrizio Castro
1 sibling, 0 replies; 5+ messages in thread
From: Fabrizio Castro @ 2019-08-29 10:21 UTC (permalink / raw)
To: Geert Uytterhoeven, Laurent Pinchart, Thierry Reding,
David Airlie, Daniel Vetter, Rob Herring, Mark Rutland
Cc: Fabrizio Castro, Sam Ravnborg, Simon Horman, Magnus Damm,
dri-devel, devicetree, linux-renesas-soc, linux-kernel,
Chris Paterson, Biju Das, Kieran Bingham, Jacopo Mondi,
xu_shunji, ebiharaml
Add binding for the idk-1110wr LVDS panel from Advantech.
Some panel-specific documentation can be found here:
https://buy.advantech.eu/Displays/Embedded-LCD-Kits-LCD-Kit-Modules/model-IDK-1110WR-55WSA1E.htm
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
---
.../display/panel/advantech,idk-1110wr.yaml | 69 ++++++++++++++++++++++
1 file changed, 69 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/panel/advantech,idk-1110wr.yaml
diff --git a/Documentation/devicetree/bindings/display/panel/advantech,idk-1110wr.yaml b/Documentation/devicetree/bindings/display/panel/advantech,idk-1110wr.yaml
new file mode 100644
index 0000000..e5fdaa0
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/panel/advantech,idk-1110wr.yaml
@@ -0,0 +1,69 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/display/panel/advantech,idk-1110wr.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Advantech IDK-1110WR 10.1" WSVGA LVDS Display Panel
+
+maintainers:
+ - Fabrizio Castro <fabrizio.castro@bp.renesas.com>
+ - Thierry Reding <thierry.reding@gmail.com>
+
+allOf:
+ - $ref: lvds.yaml#
+
+properties:
+ compatible:
+ items:
+ - const: advantech,idk-1110wr
+ - {} # panel-lvds, but not listed here to avoid false select
+
+ data-mapping:
+ const: jeida-24
+
+ width-mm:
+ const: 223
+
+ height-mm:
+ const: 125
+
+ panel-timing: true
+ port: true
+
+additionalProperties: false
+
+required:
+ - compatible
+
+examples:
+ - |+
+ panel {
+ compatible = "advantech,idk-1110wr", "panel-lvds";
+
+ width-mm = <223>;
+ height-mm = <125>;
+
+ data-mapping = "jeida-24";
+
+ panel-timing {
+ /* 1024x600 @60Hz */
+ clock-frequency = <51200000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hsync-len = <240>;
+ hfront-porch = <40>;
+ hback-porch = <40>;
+ vsync-len = <10>;
+ vfront-porch = <15>;
+ vback-porch = <10>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds_encoder>;
+ };
+ };
+ };
+
+...
--
2.7.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
2019-08-29 10:21 [PATCH 0/2] Add LVDS panel support to HiHope RZ/G2M Fabrizio Castro
2019-08-29 10:21 ` [PATCH 1/2] dt-bindings: display: Add idk-1110wr binding Fabrizio Castro
@ 2019-08-29 10:21 ` Fabrizio Castro
2019-08-29 10:50 ` Geert Uytterhoeven
1 sibling, 1 reply; 5+ messages in thread
From: Fabrizio Castro @ 2019-08-29 10:21 UTC (permalink / raw)
To: Geert Uytterhoeven, Laurent Pinchart, Thierry Reding,
David Airlie, Daniel Vetter, Rob Herring, Mark Rutland
Cc: Fabrizio Castro, Sam Ravnborg, Simon Horman, Magnus Damm,
dri-devel, devicetree, linux-renesas-soc, Chris Paterson,
Biju Das, Kieran Bingham, Jacopo Mondi, xu_shunji, ebiharaml
The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
from Advantech, however the panel isn't sold alongside the board.
A new dts, adding everything that's required to get the panel to
work the HiHope RZ/G2M, is the most convenient way to support the
HiHope RZ/G2M when it's connected to the idk-1110wr.
Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/Makefile | 1 +
.../r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts | 86 ++++++++++++++++++++++
2 files changed, 87 insertions(+)
create mode 100644 arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
diff --git a/arch/arm64/boot/dts/renesas/Makefile b/arch/arm64/boot/dts/renesas/Makefile
index 42b74c2..5d94301 100644
--- a/arch/arm64/boot/dts/renesas/Makefile
+++ b/arch/arm64/boot/dts/renesas/Makefile
@@ -1,6 +1,7 @@
# SPDX-License-Identifier: GPL-2.0
dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m.dtb
dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-ex.dtb
+dtb-$(CONFIG_ARCH_R8A774A1) += r8a774a1-hihope-rzg2m-ex-idk-1110wr.dtb
dtb-$(CONFIG_ARCH_R8A774C0) += r8a774c0-cat874.dtb r8a774c0-ek874.dtb
dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-salvator-x.dtb r8a7795-h3ulcb.dtb
dtb-$(CONFIG_ARCH_R8A7795) += r8a7795-h3ulcb-kf.dtb
diff --git a/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
new file mode 100644
index 0000000..67fe04c
--- /dev/null
+++ b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
@@ -0,0 +1,86 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device Tree Source for the HiHope RZ/G2M sub board connected to an
+ * Advantech IDK-1110WR 10.1" LVDS panel
+ *
+ * Copyright (C) 2019 Renesas Electronics Corp.
+ */
+
+#include "r8a774a1-hihope-rzg2m-ex.dts"
+
+/ {
+ backlight {
+ compatible = "pwm-backlight";
+ pwms = <&pwm0 0 50000>;
+
+ brightness-levels = <0 2 8 16 32 64 128 255>;
+ default-brightness-level = <6>;
+ };
+
+ panel-lvds {
+ compatible = "advantech,idk-1110wr", "panel-lvds";
+
+ width-mm = <223>;
+ height-mm = <125>;
+
+ data-mapping = "jeida-24";
+
+ panel-timing {
+ /* 1024x600 @60Hz */
+ clock-frequency = <51200000>;
+ hactive = <1024>;
+ vactive = <600>;
+ hsync-len = <240>;
+ hfront-porch = <40>;
+ hback-porch = <40>;
+ vfront-porch = <15>;
+ vback-porch = <10>;
+ vsync-len = <10>;
+ };
+
+ port {
+ panel_in: endpoint {
+ remote-endpoint = <&lvds0_out>;
+ };
+ };
+ };
+};
+
+&gpio1 {
+ /*
+ * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
+ * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
+ */
+ lvds-connector-en-gpio{
+ gpio-hog;
+ gpios = <20 GPIO_ACTIVE_HIGH>;
+ output-low;
+ line-name = "lvds-connector-en-gpio";
+ };
+};
+
+&lvds0 {
+ status = "okay";
+
+ ports {
+ port@1 {
+ lvds0_out: endpoint {
+ remote-endpoint = <&panel_in>;
+ };
+ };
+ };
+};
+
+&pfc {
+ pwm0_pins: pwm0 {
+ groups = "pwm0";
+ function = "pwm0";
+ };
+};
+
+&pwm0 {
+ pinctrl-0 = <&pwm0_pins>;
+ pinctrl-names = "default";
+
+ status = "okay";
+};
--
2.7.4
^ permalink raw reply related [flat|nested] 5+ messages in thread
* Re: [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
2019-08-29 10:21 ` [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display Fabrizio Castro
@ 2019-08-29 10:50 ` Geert Uytterhoeven
2019-08-29 11:08 ` Fabrizio Castro
0 siblings, 1 reply; 5+ messages in thread
From: Geert Uytterhoeven @ 2019-08-29 10:50 UTC (permalink / raw)
To: Fabrizio Castro
Cc: Geert Uytterhoeven, Laurent Pinchart, Thierry Reding,
David Airlie, Daniel Vetter, Rob Herring, Mark Rutland,
Sam Ravnborg, Simon Horman, Magnus Damm, DRI Development,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux-Renesas, Chris Paterson, Biju Das, Kieran Bingham,
Jacopo Mondi, xu_shunji, ebiharaml
Hi Fabrizio,
On Thu, Aug 29, 2019 at 12:22 PM Fabrizio Castro
<fabrizio.castro@bp.renesas.com> wrote:
> The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
> from Advantech, however the panel isn't sold alongside the board.
> A new dts, adding everything that's required to get the panel to
> work the HiHope RZ/G2M, is the most convenient way to support the
> HiHope RZ/G2M when it's connected to the idk-1110wr.
>
> Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Thanks for your patch!
> --- /dev/null
> +++ b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
> +&gpio1 {
> + /*
> + * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
> + * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
> + */
> + lvds-connector-en-gpio{
Missing space before curly brace.
Gr{oetje,eeting}s,
Geert
--
Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
In personal conversations with technical people, I call myself a hacker. But
when I'm talking to journalists I just say "programmer" or something like that.
-- Linus Torvalds
^ permalink raw reply [flat|nested] 5+ messages in thread
* RE: [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
2019-08-29 10:50 ` Geert Uytterhoeven
@ 2019-08-29 11:08 ` Fabrizio Castro
0 siblings, 0 replies; 5+ messages in thread
From: Fabrizio Castro @ 2019-08-29 11:08 UTC (permalink / raw)
To: Geert Uytterhoeven
Cc: Geert Uytterhoeven, Laurent Pinchart, Thierry Reding,
David Airlie, Daniel Vetter, Rob Herring, Mark Rutland,
Sam Ravnborg, Simon Horman, Magnus Damm, DRI Development,
open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS,
Linux-Renesas, Chris Paterson, Biju Das, Kieran Bingham,
Jacopo Mondi, xu_shunji, ebiharaml
Hi Geert,
Thank you for your feedback!
> From: Geert Uytterhoeven <geert@linux-m68k.org>
> Sent: 29 August 2019 11:51
> Subject: Re: [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display
>
> Hi Fabrizio,
>
> On Thu, Aug 29, 2019 at 12:22 PM Fabrizio Castro
> <fabrizio.castro@bp.renesas.com> wrote:
> > The HiHope RZ/G2M is advertised as compatible with panel idk-1110wr
> > from Advantech, however the panel isn't sold alongside the board.
> > A new dts, adding everything that's required to get the panel to
> > work the HiHope RZ/G2M, is the most convenient way to support the
> > HiHope RZ/G2M when it's connected to the idk-1110wr.
> >
> > Signed-off-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
>
> Thanks for your patch!
>
> > --- /dev/null
> > +++ b/arch/arm64/boot/dts/renesas/r8a774a1-hihope-rzg2m-ex-idk-1110wr.dts
>
> > +&gpio1 {
> > + /*
> > + * When GP1_20 is LOW LVDS0 is connected to the LVDS connector
> > + * When GP1_20 is HIGH LVDS0 is connected to the LT8918L
> > + */
> > + lvds-connector-en-gpio{
>
> Missing space before curly brace.
Doh, thank you for spotting this, I'll send a v2.
Cheers,
Fab
>
> Gr{oetje,eeting}s,
>
> Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@linux-m68k.org
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
> -- Linus Torvalds
^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2019-08-29 11:08 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2019-08-29 10:21 [PATCH 0/2] Add LVDS panel support to HiHope RZ/G2M Fabrizio Castro
2019-08-29 10:21 ` [PATCH 1/2] dt-bindings: display: Add idk-1110wr binding Fabrizio Castro
2019-08-29 10:21 ` [PATCH 2/2] arm64: dts: renesas: Add HiHope RZ/G2M board with idk-1110wr display Fabrizio Castro
2019-08-29 10:50 ` Geert Uytterhoeven
2019-08-29 11:08 ` Fabrizio Castro
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).