linux-renesas-soc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: "Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>
To: Kieran Bingham <kieran.bingham@ideasonboard.com>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	Jacopo Mondi <jacopo@jmondi.org>,
	linux-media@vger.kernel.org
Cc: linux-renesas-soc@vger.kernel.org,
	"Niklas Söderlund" <niklas.soderlund+renesas@ragnatech.se>
Subject: [PATCH v4 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter
Date: Thu, 29 Nov 2018 03:01:47 +0100	[thread overview]
Message-ID: <20181129020147.22115-5-niklas.soderlund+renesas@ragnatech.se> (raw)
In-Reply-To: <20181129020147.22115-1-niklas.soderlund+renesas@ragnatech.se>

The driver fixed the TXA CSI-2 transmitter in 4-lane mode while it could
operate using 1-, 2- and 4-lanes. Update the driver to support all
available modes.

The driver makes use of large tables of static register/value writes
when powering up/down the TXA and TXB transmitters which include the
write to the NUM_LANES register. By converting the tables into functions
and using parameters the power up/down functions for TXA and TXB power
up/down can be merged and used for both transmitters.

Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org>

---
* Changes since v3
- Fix spelling in commit message, thanks Laurent!
* Changes since v2
- Fix typos in comments.
- Remove unneeded boiler plait code in adv748x_tx_power() as suggested
  by Jacopo and Laurent.
- Take into account the two different register used when powering up TXA
  and TXB due to an earlier patch in this series aligns the power
  sequence with the manual.

* Changes since v1
- Convert tables of register/value writes into functions instead of
  intercepting and modifying the writes to the NUM_LANES register.
---
 drivers/media/i2c/adv748x/adv748x-core.c | 157 ++++++++++++-----------
 1 file changed, 79 insertions(+), 78 deletions(-)

diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c
index 9d80d7f3062b16bc..d94c63cb6a2efdba 100644
--- a/drivers/media/i2c/adv748x/adv748x-core.c
+++ b/drivers/media/i2c/adv748x/adv748x-core.c
@@ -125,6 +125,16 @@ int adv748x_write(struct adv748x_state *state, u8 page, u8 reg, u8 value)
 	return regmap_write(state->regmap[page], reg, value);
 }
 
+static int adv748x_write_check(struct adv748x_state *state, u8 page, u8 reg,
+			       u8 value, int *error)
+{
+	if (*error)
+		return *error;
+
+	*error = adv748x_write(state, page, reg, value);
+	return *error;
+}
+
 /* adv748x_write_block(): Write raw data with a maximum of I2C_SMBUS_BLOCK_MAX
  * size to one or more registers.
  *
@@ -231,79 +241,77 @@ static int adv748x_write_regs(struct adv748x_state *state,
  * TXA and TXB
  */
 
-static const struct adv748x_reg_value adv748x_power_up_txa_4lane[] = {
-
-	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
-	{ADV748X_PAGE_TXA, 0x00, 0xa4},	/* Set Auto DPHY Timing */
-	{ADV748X_PAGE_TXA, 0xdb, 0x10},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0xd6, 0x07},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0xc4, 0x0a},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0x71, 0x33},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0x72, 0x11},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
-
-	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0x1e, 0x40},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
-	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
-	{ADV748X_PAGE_TXA, 0x00, 0x24 },/* Power-up CSI-TX */
-	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
-	{ADV748X_PAGE_TXA, 0xc1, 0x2b},	/* ADI Required Write */
-	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
-	{ADV748X_PAGE_TXA, 0x31, 0x80},	/* ADI Required Write */
-
-	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
-};
-
-static const struct adv748x_reg_value adv748x_power_down_txa_4lane[] = {
-
-	{ADV748X_PAGE_TXA, 0x31, 0x82},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0x1e, 0x00},	/* ADI Required Write */
-	{ADV748X_PAGE_TXA, 0x00, 0x84},	/* Enable 4-lane MIPI */
-	{ADV748X_PAGE_TXA, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
-	{ADV748X_PAGE_TXA, 0xc1, 0x3b},	/* ADI Required Write */
-
-	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
-};
-
-static const struct adv748x_reg_value adv748x_power_up_txb_1lane[] = {
-
-	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
-	{ADV748X_PAGE_TXB, 0x00, 0xa1},	/* Set Auto DPHY Timing */
-	{ADV748X_PAGE_TXB, 0xd2, 0x40},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0xc4, 0x0a},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0x71, 0x33},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0x72, 0x11},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0xf0, 0x00},	/* i2c_dphy_pwdn - 1'b0 */
-
-	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0x1e, 0x40},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
-	{ADV748X_PAGE_WAIT, 0x00, 0x02},/* delay 2 */
-	{ADV748X_PAGE_TXB, 0x00, 0x21 },/* Power-up CSI-TX */
-	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
-	{ADV748X_PAGE_TXB, 0xc1, 0x2b},	/* ADI Required Write */
-	{ADV748X_PAGE_WAIT, 0x00, 0x01},/* delay 1 */
-	{ADV748X_PAGE_TXB, 0x31, 0x80},	/* ADI Required Write */
-
-	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
-};
-
-static const struct adv748x_reg_value adv748x_power_down_txb_1lane[] = {
-
-	{ADV748X_PAGE_TXB, 0x31, 0x82},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0x1e, 0x00},	/* ADI Required Write */
-	{ADV748X_PAGE_TXB, 0x00, 0x81},	/* Enable 1-lane MIPI */
-	{ADV748X_PAGE_TXB, 0xda, 0x01},	/* i2c_mipi_pll_en - 1'b1 */
-	{ADV748X_PAGE_TXB, 0xc1, 0x3b},	/* ADI Required Write */
-
-	{ADV748X_PAGE_EOR, 0xff, 0xff}	/* End of register table */
-};
+static int adv748x_power_up_tx(struct adv748x_csi2 *tx)
+{
+	struct adv748x_state *state = tx->state;
+	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
+	int ret = 0;
+
+	/* Enable n-lane MIPI */
+	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
+
+	/* Set Auto DPHY Timing */
+	adv748x_write_check(state, page, 0x00, 0xa0 | tx->num_lanes, &ret);
+
+	/* ADI Required Write */
+	if (is_txa(tx)) {
+		adv748x_write_check(state, page, 0xdb, 0x10, &ret);
+		adv748x_write_check(state, page, 0xd6, 0x07, &ret);
+	} else {
+		adv748x_write_check(state, page, 0xd2, 0x40, &ret);
+	}
+
+	adv748x_write_check(state, page, 0xc4, 0x0a, &ret);
+	adv748x_write_check(state, page, 0x71, 0x33, &ret);
+	adv748x_write_check(state, page, 0x72, 0x11, &ret);
+
+	/* i2c_dphy_pwdn - 1'b0 */
+	adv748x_write_check(state, page, 0xf0, 0x00, &ret);
+
+	/* ADI Required Writes*/
+	adv748x_write_check(state, page, 0x31, 0x82, &ret);
+	adv748x_write_check(state, page, 0x1e, 0x40, &ret);
+
+	/* i2c_mipi_pll_en - 1'b1 */
+	adv748x_write_check(state, page, 0xda, 0x01, &ret);
+	usleep_range(2000, 2500);
+
+	/* Power-up CSI-TX */
+	adv748x_write_check(state, page, 0x00, 0x20 | tx->num_lanes, &ret);
+	usleep_range(1000, 1500);
+
+	/* ADI Required Writes */
+	adv748x_write_check(state, page, 0xc1, 0x2b, &ret);
+	usleep_range(1000, 1500);
+	adv748x_write_check(state, page, 0x31, 0x80, &ret);
+
+	return ret;
+}
+
+static int adv748x_power_down_tx(struct adv748x_csi2 *tx)
+{
+	struct adv748x_state *state = tx->state;
+	u8 page = is_txa(tx) ? ADV748X_PAGE_TXA : ADV748X_PAGE_TXB;
+	int ret = 0;
+
+	/* ADI Required Writes */
+	adv748x_write_check(state, page, 0x31, 0x82, &ret);
+	adv748x_write_check(state, page, 0x1e, 0x00, &ret);
+
+	/* Enable n-lane MIPI */
+	adv748x_write_check(state, page, 0x00, 0x80 | tx->num_lanes, &ret);
+
+	/* i2c_mipi_pll_en - 1'b1 */
+	adv748x_write_check(state, page, 0xda, 0x01, &ret);
+
+	/* ADI Required Write */
+	adv748x_write_check(state, page, 0xc1, 0x3b, &ret);
+
+	return ret;
+}
 
 int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
 {
-	struct adv748x_state *state = tx->state;
-	const struct adv748x_reg_value *reglist;
 	int val;
 
 	if (!is_tx_enabled(tx))
@@ -321,14 +329,7 @@ int adv748x_tx_power(struct adv748x_csi2 *tx, bool on)
 	WARN_ONCE((on && val & ADV748X_CSI_FS_AS_LS_UNKNOWN),
 			"Enabling with unknown bit set");
 
-	if (on)
-		reglist = is_txa(tx) ? adv748x_power_up_txa_4lane :
-				       adv748x_power_up_txb_1lane;
-	else
-		reglist = is_txa(tx) ? adv748x_power_down_txa_4lane :
-				       adv748x_power_down_txb_1lane;
-
-	return adv748x_write_regs(state, reglist);
+	return on ? adv748x_power_up_tx(tx) : adv748x_power_down_tx(tx);
 }
 
 /* -----------------------------------------------------------------------------
-- 
2.19.1

  parent reply	other threads:[~2018-11-29 13:07 UTC|newest]

Thread overview: 12+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2018-11-29  2:01 [PATCH v4 0/4] i2c: adv748x: add support for CSI-2 TXA to work in 1-, 2- and 4-lane mode Niklas Söderlund
2018-11-29  2:01 ` [PATCH v4 1/4] dt-bindings: adv748x: make data-lanes property mandatory for CSI-2 endpoints Niklas Söderlund
2018-11-29 18:58   ` Laurent Pinchart
2018-12-07 23:08   ` Rob Herring
2019-01-11 12:47   ` Kieran Bingham
2018-11-29  2:01 ` [PATCH v4 2/4] i2c: adv748x: reuse power up sequence when initializing CSI-2 Niklas Söderlund
2019-01-11 12:48   ` Kieran Bingham
2018-11-29  2:01 ` [PATCH v4 3/4] i2c: adv748x: store number of CSI-2 lanes described in device tree Niklas Söderlund
2019-01-11 12:50   ` Kieran Bingham
2018-11-29  2:01 ` Niklas Söderlund [this message]
2019-01-11 12:51   ` [PATCH v4 4/4] i2c: adv748x: configure number of lanes used for TXA CSI-2 transmitter Kieran Bingham
2019-01-11 12:52 ` [PATCH v4 0/4] i2c: adv748x: add support for CSI-2 TXA to work in 1-, 2- and 4-lane mode Kieran Bingham

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20181129020147.22115-5-niklas.soderlund+renesas@ragnatech.se \
    --to=niklas.soderlund+renesas@ragnatech.se \
    --cc=jacopo@jmondi.org \
    --cc=kieran.bingham@ideasonboard.com \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body. 
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).