From: "Niklas Söderlund" <niklas.soderlund@ragnatech.se>
To: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Cc: Koji Matsuoka <koji.matsuoka.xm@renesas.com>,
Jacopo Mondi <jacopo@jmondi.org>,
Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
Steve Longerbeam <steve_longerbeam@mentor.com>,
linux-renesas-soc@vger.kernel.org, linux-media@vger.kernel.org
Subject: Re: [PATCH 1/2] media: i2c: adv748x: Convert SW reset routine to function
Date: Mon, 14 Jan 2019 15:43:45 +0100 [thread overview]
Message-ID: <20190114144345.GG30160@bigcity.dyn.berto.se> (raw)
In-Reply-To: <20190111174141.12594-2-kieran.bingham+renesas@ideasonboard.com>
Hi Kieran,
Thanks for your work.
On 2019-01-11 17:41:40 +0000, Kieran Bingham wrote:
> The ADV748x is currently reset by writting a small table of registers to
> the device.
>
> The table lacks documentation and contains magic values to perform the
> actions, including using a fake register address to introduce a delay
> loop.
>
> Remove the table, and convert to code, documenting the purpose of the
> specific writes along the way.
>
> Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
> ---
> drivers/media/i2c/adv748x/adv748x-core.c | 32 ++++++++++++++++--------
> drivers/media/i2c/adv748x/adv748x.h | 16 ++++++++++++
> 2 files changed, 38 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/media/i2c/adv748x/adv748x-core.c b/drivers/media/i2c/adv748x/adv748x-core.c
> index 02f9c440301c..252bdb28b18b 100644
> --- a/drivers/media/i2c/adv748x/adv748x-core.c
> +++ b/drivers/media/i2c/adv748x/adv748x-core.c
> @@ -389,15 +389,6 @@ static const struct media_entity_operations adv748x_media_ops = {
> * HW setup
> */
>
> -static const struct adv748x_reg_value adv748x_sw_reset[] = {
> -
> - {ADV748X_PAGE_IO, 0xff, 0xff}, /* SW reset */
> - {ADV748X_PAGE_WAIT, 0x00, 0x05},/* delay 5 */
> - {ADV748X_PAGE_IO, 0x01, 0x76}, /* ADI Required Write */
> - {ADV748X_PAGE_IO, 0xf2, 0x01}, /* Enable I2C Read Auto-Increment */
> - {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */
> -};
> -
> /* Initialize CP Core with RGB888 format. */
> static const struct adv748x_reg_value adv748x_init_hdmi[] = {
> /* Disable chip powerdown & Enable HDMI Rx block */
> @@ -474,12 +465,33 @@ static const struct adv748x_reg_value adv748x_init_afe[] = {
> {ADV748X_PAGE_EOR, 0xff, 0xff} /* End of register table */
> };
>
> +static int adv748x_sw_reset(struct adv748x_state *state)
> +{
> + int ret;
> +
> + ret = io_write(state, ADV748X_IO_REG_FF, ADV748X_IO_REG_FF_MAIN_RESET);
> + if (ret)
> + return ret;
> +
> + usleep_range(5000, 6000);
> +
> + /* Disable CEC Wakeup from power-down mode */
> + ret = io_clrset(state, ADV748X_IO_REG_01, ADV748X_IO_REG_01_PWRDN_MASK,
> + ADV748X_IO_REG_01_PWRDNB);
> + if (ret)
> + return ret;
> +
> + /* Enable I2C Read Auto-Increment for consecutive reads */
> + return io_write(state, ADV748X_IO_REG_F2,
> + ADV748X_IO_REG_F2_READ_AUTO_INC);
> +}
> +
> static int adv748x_reset(struct adv748x_state *state)
> {
> int ret;
> u8 regval = 0;
>
> - ret = adv748x_write_regs(state, adv748x_sw_reset);
> + ret = adv748x_sw_reset(state);
> if (ret < 0)
> return ret;
>
> diff --git a/drivers/media/i2c/adv748x/adv748x.h b/drivers/media/i2c/adv748x/adv748x.h
> index b00c1995efb0..2f8d751cfbb0 100644
> --- a/drivers/media/i2c/adv748x/adv748x.h
> +++ b/drivers/media/i2c/adv748x/adv748x.h
> @@ -211,6 +211,11 @@ struct adv748x_state {
> #define ADV748X_IO_PD 0x00 /* power down controls */
> #define ADV748X_IO_PD_RX_EN BIT(6)
>
> +#define ADV748X_IO_REG_01 0x01 /* pwrdn{2}b, prog_xtal_freq */
> +#define ADV748X_IO_REG_01_PWRDN_MASK (BIT(7) | BIT(6))
> +#define ADV748X_IO_REG_01_PWRDN2B BIT(7) /* CEC Wakeup Support */
> +#define ADV748X_IO_REG_01_PWRDNB BIT(6) /* CEC Wakeup Support */
> +
> #define ADV748X_IO_REG_04 0x04
> #define ADV748X_IO_REG_04_FORCE_FR BIT(0) /* Force CP free-run */
>
> @@ -229,8 +234,19 @@ struct adv748x_state {
> #define ADV748X_IO_CHIP_REV_ID_1 0xdf
> #define ADV748X_IO_CHIP_REV_ID_2 0xe0
>
> +#define ADV748X_IO_REG_F2 0xf2
> +#define ADV748X_IO_REG_F2_READ_AUTO_INC BIT(0)
> +
> +/* For PAGE slave address offsets */
> #define ADV748X_IO_SLAVE_ADDR_BASE 0xf2
>
> +/*
> + * The ADV748x_Recommended_Settings_PrA_2014-08-20.pdf details both 0x80 and
> + * 0xff as examples for performing a software reset.
> + */
> +#define ADV748X_IO_REG_FF 0xff
> +#define ADV748X_IO_REG_FF_MAIN_RESET 0xff
> +
> /* HDMI RX Map */
> #define ADV748X_HDMI_LW1 0x07 /* line width_1 */
> #define ADV748X_HDMI_LW1_VERT_FILTER BIT(7)
> --
> 2.17.1
>
--
Regards,
Niklas Söderlund
next prev parent reply other threads:[~2019-01-14 14:43 UTC|newest]
Thread overview: 12+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-01-11 17:41 [PATCH 0/2] media: i2c: adv748x: Refactor sw_reset handling Kieran Bingham
2019-01-11 17:41 ` [PATCH 1/2] media: i2c: adv748x: Convert SW reset routine to function Kieran Bingham
2019-01-11 20:15 ` Laurent Pinchart
2019-01-12 16:50 ` Kieran Bingham
2019-01-18 12:26 ` Laurent Pinchart
2019-01-14 14:43 ` Niklas Söderlund [this message]
2019-01-18 12:09 ` Hans Verkuil
2019-01-18 13:34 ` Kieran Bingham
2019-01-11 17:41 ` [PATCH 2/2] media: i2c: adv748x: Remove PAGE_WAIT Kieran Bingham
2019-01-11 20:23 ` Laurent Pinchart
2019-01-12 16:51 ` Kieran Bingham
2019-01-14 14:44 ` Niklas Söderlund
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20190114144345.GG30160@bigcity.dyn.berto.se \
--to=niklas.soderlund@ragnatech.se \
--cc=jacopo@jmondi.org \
--cc=kieran.bingham+renesas@ideasonboard.com \
--cc=koji.matsuoka.xm@renesas.com \
--cc=laurent.pinchart@ideasonboard.com \
--cc=linux-media@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=steve_longerbeam@mentor.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).