[PATCH v3 1/2] arm64: dts: renesas: r8a7795: Create thermal zone to support IPA

[Simon Horman <horms+renesas@verge.net.au>]

From: Dien Pham <dien.pham.ry@renesas.com>

Setup a thermal zone driven by SoC temperature sensor.
Create passive trip points and bind them to CPUFreq cooling
device that supports power extension.

In R-Car Gen3, IPA is supported for only one channel
 (on H3/M3/M3N board, it is channel THS3). Reason:
  Currently, IPA controls base on only CPU temperature.
  And only one thermal channel is assembled closest
  CPU cores is selected as target of IPA.
  If other channels are used, IPA controlling is not properly.

The device supports 5 cooling states which can be categorised as follows:

0 & 1) boost (clocking up)
2)     default
3 & 4) cooling (clocking down)

Currently the thermal framework assumes that the default is the minimum,
or in other words there is no provision for handling boost states.
So this patch only describes the upper 3 states, default and cooling.

A single cooling device is described for all A57 CPUs as this
reflects that physically there is only one cooling device present.

This patch improves on an earlier version by:

* Omitting cooling-max-level and cooling-min-level properties which
  are no longer present in mainline as of v4.17
* Removing an unused trip-point0 node sub-property from the trips
  property.
* Using cooling-device indexes such that maximum refers to maximum cooling
  rather than the inverse.

The long signed-off by chain below reflects many revisions, mainly
internal, that this patch has been through.

Signed-off-by: Keita Kobayashi <keita.kobayashi.ym@renesas.com>
Signed-off-by: Gaku Inami <gaku.inami.xw@bp.renesas.com>
Signed-off-by: Hien Dang <hien.dang.eb@rvc.renesas.com>
Signed-off-by: An Huynh <an.huynh.uj@rvc.renesas.com>
Signed-off-by: Takeshi Kihara <takeshi.kihara.df@renesas.com>
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>

---
v3 [Simon Horman]
* Move adding dynamic-power-coefficient properties into a separate
  patch as these are properties of the CPU.
---
 arch/arm64/boot/dts/renesas/r8a7795.dtsi | 52 +++++++++-----------------------
 1 file changed, 15 insertions(+), 37 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795.dtsi b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
index abeac3059383..2b34a4b3e4d8 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795.dtsi
+++ b/arch/arm64/boot/dts/renesas/r8a7795.dtsi
@@ -207,6 +207,7 @@
 			power-domains = <&sysc R8A7795_PD_CA53_CPU0>;
 			next-level-cache = <&L2_CA53>;
 			enable-method = "psci";
+			#cooling-cells = <2>;
 			clocks = <&cpg CPG_CORE R8A7795_CLK_Z2>;
 			operating-points-v2 = <&cluster1_opp>;
 			capacity-dmips-mhz = <535>;
@@ -3098,58 +3099,30 @@
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 0>;
+			sustainable-power = <6313>;
 
 			trips {
-				sensor1_passive: sensor1-passive {
-					temperature = <95000>;
-					hysteresis = <1000>;
-					type = "passive";
-				};
 				sensor1_crit: sensor1-crit {
 					temperature = <120000>;
 					hysteresis = <1000>;
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&sensor1_passive>;
-					cooling-device = <&a57_0 4 4>,
-							 <&a57_1 4 4>,
-							 <&a57_2 4 4>,
-							 <&a57_3 4 4>;
-				};
-			};
 		};
 
 		sensor_thermal2: sensor-thermal2 {
 			polling-delay-passive = <250>;
 			polling-delay = <1000>;
 			thermal-sensors = <&tsc 1>;
+			sustainable-power = <6313>;
 
 			trips {
-				sensor2_passive: sensor2-passive {
-					temperature = <95000>;
-					hysteresis = <1000>;
-					type = "passive";
-				};
 				sensor2_crit: sensor2-crit {
 					temperature = <120000>;
 					hysteresis = <1000>;
 					type = "critical";
 				};
 			};
-
-			cooling-maps {
-				map0 {
-					trip = <&sensor2_passive>;
-					cooling-device = <&a57_0 4 4>,
-							 <&a57_1 4 4>,
-							 <&a57_2 4 4>,
-							 <&a57_3 4 4>;
-				};
-			};
 		};
 
 		sensor_thermal3: sensor-thermal3 {
@@ -3158,11 +3131,12 @@
 			thermal-sensors = <&tsc 2>;
 
 			trips {
-				sensor3_passive: sensor3-passive {
-					temperature = <95000>;
+				target: trip-point1 {
+					temperature = <100000>;
 					hysteresis = <1000>;
 					type = "passive";
 				};
+
 				sensor3_crit: sensor3-crit {
 					temperature = <120000>;
 					hysteresis = <1000>;
@@ -3172,11 +3146,15 @@
 
 			cooling-maps {
 				map0 {
-					trip = <&sensor3_passive>;
-					cooling-device = <&a57_0 4 4>,
-							 <&a57_1 4 4>,
-							 <&a57_2 4 4>,
-							 <&a57_3 4 4>;
+					trip = <&target>;
+					cooling-device = <&a57_0 2 4>;
+					contribution = <1024>;
+				};
+
+				map1 {
+					trip = <&target>;
+					cooling-device = <&a53_0 0 2>;
+					contribution = <1024>;
 				};
 			};
 		};
-- 
2.11.0