Linux-Renesas-SoC Archive on lore.kernel.org
 help / color / Atom feed
From: Chris Brandt <chris.brandt@renesas.com>
To: Rob Herring <robh+dt@kernel.org>,
	Mark Rutland <mark.rutland@arm.com>,
	Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
	Simon Horman <horms@verge.net.au>,
	Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>,
	Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>,
	Chunfeng Yun <chunfeng.yun@mediatek.com>,
	Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>,
	<linux-usb@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-renesas-soc@vger.kernel.org>,
	"Chris Brandt" <chris.brandt@renesas.com>
Subject: [PATCH v4 00/13] usb: Add host and device support for RZ/A2
Date: Wed, 15 May 2019 10:20:35 -0500
Message-ID: <20190515152048.42363-1-chris.brandt@renesas.com> (raw)


NOTE 1:
This series requires the follow patch from Shimoda-san.
  [PATCH v2] usb: renesas_usbhs: Use specific struct instead of USBHS_TYPE_* enums


NOTE 2:
The first 2 patches from the V3 series (add USB_X1 clock) were removed from this
V4 series because Simon already applied them.



For the most part, the RZ/A2 has the same USB 2.0 host and device
HW as the R-Car Gen3, so we can reuse a lot of the code.

However, there are a couple extra register bits, and the CFIFO
register 8-bit access works a little different.

There is a dedicated DMAC for the RZ/A2 USB Device HW, but we
have not been able to reliably get that working yet, so device
operation is pio only at the moment.

On the RZ/A2M eval board, both USB channels can be used as either
host or device. But, it's not set up for otg (ie, there are jumpers
and separate connectors). Therefore, below is an example of what it
would look like to enable USB channel 0 as a device instead of a host.

&usb2_phy0 {
	pinctrl-names = "default";
	pinctrl-0 = <&usb0_pins>;
	dr_mode = "peripheral";
	status = "okay";
};

&usbhs0 {
	status = "okay";
};

Chris Brandt (13):
  phy: renesas: rcar-gen3-usb2: detect usb_x1 clock
  dt-bindings: rcar-gen3-phy-usb2: Document use of usb_x1
  phy: renesas: rcar-gen3-usb2: Check dr_mode when not using OTG
  dt-bindings: rcar-gen3-phy-usb2: Document dr_mode
  dt-bindings: rcar-gen3-phy-usb2: Add r7s9210 support
  usb: renesas_usbhs: move flags to param
  usb: renesas_usbhs: add support for CNEN bit
  usb: renesas_usbhs: support byte addressable CFIFO
  usb: renesas_usbhs: Add support for RZ/A2
  dt-bindings: usb: renesas_usbhs: Add support for r7s9210
  ARM: dts: r7s9210: Add USB Host support
  ARM: dts: r7s9210: Add USB Device support
  ARM: dts: rza2mevb: Add USB Host support

 .../devicetree/bindings/phy/rcar-gen3-phy-usb2.txt | 19 +++--
 .../devicetree/bindings/usb/renesas_usbhs.txt      |  2 +
 arch/arm/boot/dts/r7s9210-rza2mevb.dts             | 36 +++++++++
 arch/arm/boot/dts/r7s9210.dtsi                     | 90 ++++++++++++++++++++++
 drivers/phy/renesas/phy-rcar-gen3-usb2.c           | 26 +++++++
 drivers/usb/renesas_usbhs/Makefile                 |  2 +-
 drivers/usb/renesas_usbhs/common.c                 | 44 +++++++----
 drivers/usb/renesas_usbhs/common.h                 |  3 +-
 drivers/usb/renesas_usbhs/fifo.c                   |  9 ++-
 drivers/usb/renesas_usbhs/rza.h                    |  1 +
 drivers/usb/renesas_usbhs/rza2.c                   | 72 +++++++++++++++++
 include/linux/usb/renesas_usbhs.h                  |  4 +
 12 files changed, 282 insertions(+), 26 deletions(-)
 create mode 100644 drivers/usb/renesas_usbhs/rza2.c

-- 
2.16.1


             reply index

Thread overview: 17+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2019-05-15 15:20 Chris Brandt [this message]
2019-05-15 15:20 ` [PATCH v4 01/13] phy: renesas: rcar-gen3-usb2: detect usb_x1 clock Chris Brandt
2019-05-15 15:20 ` [PATCH v4 02/13] dt-bindings: rcar-gen3-phy-usb2: Document use of usb_x1 Chris Brandt
2019-05-15 15:20 ` [PATCH v4 03/13] phy: renesas: rcar-gen3-usb2: Check dr_mode when not using OTG Chris Brandt
2019-05-15 15:20 ` [PATCH v4 04/13] dt-bindings: rcar-gen3-phy-usb2: Document dr_mode Chris Brandt
2019-05-15 15:20 ` [PATCH v4 05/13] dt-bindings: rcar-gen3-phy-usb2: Add r7s9210 support Chris Brandt
2019-05-15 15:20 ` [PATCH v4 06/13] usb: renesas_usbhs: move flags to param Chris Brandt
2019-05-15 15:20 ` [PATCH v4 07/13] usb: renesas_usbhs: add support for CNEN bit Chris Brandt
2019-05-15 15:20 ` [PATCH v4 08/13] usb: renesas_usbhs: support byte addressable CFIFO Chris Brandt
2019-05-15 15:20 ` [PATCH v4 09/13] usb: renesas_usbhs: Add support for RZ/A2 Chris Brandt
2019-05-15 15:20 ` [PATCH v4 10/13] dt-bindings: usb: renesas_usbhs: Add support for r7s9210 Chris Brandt
2019-05-15 15:20 ` [PATCH v4 11/13] ARM: dts: r7s9210: Add USB Host support Chris Brandt
2019-05-20 11:42   ` Simon Horman
2019-05-15 15:20 ` [PATCH v4 12/13] ARM: dts: r7s9210: Add USB Device support Chris Brandt
2019-05-20 11:43   ` Simon Horman
2019-05-15 15:20 ` [PATCH v4 13/13] ARM: dts: rza2mevb: Add USB Host support Chris Brandt
2019-05-20 11:43   ` Simon Horman

Reply instructions:

You may reply publically to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20190515152048.42363-1-chris.brandt@renesas.com \
    --to=chris.brandt@renesas.com \
    --cc=chunfeng.yun@mediatek.com \
    --cc=devicetree@vger.kernel.org \
    --cc=geert@linux-m68k.org \
    --cc=gregkh@linuxfoundation.org \
    --cc=horms@verge.net.au \
    --cc=kuninori.morimoto.gx@renesas.com \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=linux-usb@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=robh+dt@kernel.org \
    --cc=sergei.shtylyov@cogentembedded.com \
    --cc=yoshihiro.shimoda.uh@renesas.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Renesas-SoC Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-renesas-soc/0 linux-renesas-soc/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-renesas-soc linux-renesas-soc/ https://lore.kernel.org/linux-renesas-soc \
		linux-renesas-soc@vger.kernel.org linux-renesas-soc@archiver.kernel.org
	public-inbox-index linux-renesas-soc


Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-renesas-soc


AGPL code for this site: git clone https://public-inbox.org/ public-inbox