linux-renesas-soc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Alex Riesen <alexander.riesen@cetitec.com>
To: Kieran Bingham <kieran.bingham@ideasonboard.com>
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>,
	Hans Verkuil <hverkuil-cisco@xs4all.nl>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	Rob Herring <robh+dt@kernel.org>,
	"Mark Rutland" <mark.rutland@arm.com>,
	<devel@driverdev.osuosl.org>, <linux-media@vger.kernel.org>,
	<linux-kernel@vger.kernel.org>, <devicetree@vger.kernel.org>,
	<linux-renesas-soc@vger.kernel.org>
Subject: [PATCH 8/8] arm64: dts: renesas: salvator: add a connection from adv748x codec (HDMI input) to the R-Car SoC
Date: Mon, 13 Jan 2020 15:15:56 +0100	[thread overview]
Message-ID: <20200113141556.GI3606@pflmari> (raw)
In-Reply-To: <cover.1578924232.git.alexander.riesen@cetitec.com>

Not sure if all variants of the Salvator board have the HDMI decoder
chip (the ADV7482) connected to the SSI4 on R-Car SoC, as it is on
Salvator-X ES1, so the the ADV7482 endpoint and connection definitions
are placed in the board file.

I do assume though that all Salvator variants have the CLK_C clock line
hard-wired to the ADV7482 HDMI decoder, and remove it from the list of
clocks provided by the R-Car sound system.

The I2C wiring is also likely to persist across the variants (similar
to ak4613, connected to the same interface), so that is in the common
file.

Signed-off-by: Alexander Riesen <alexander.riesen@cetitec.com>
---
 .../dts/renesas/r8a7795-es1-salvator-x.dts    | 24 ++++++++++++-
 .../boot/dts/renesas/salvator-common.dtsi     | 35 ++++++++++++++++---
 2 files changed, 53 insertions(+), 6 deletions(-)

diff --git a/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts b/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
index c72968623e94..10f74f7a0efe 100644
--- a/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
+++ b/arch/arm64/boot/dts/renesas/r8a7795-es1-salvator-x.dts
@@ -136,9 +136,29 @@
 				playback = <&ssi3>;
 			};
 		};
+		rsnd_port3: port@3 {
+			reg = <3>;
+			rsnd_endpoint3: endpoint {
+				remote-endpoint = <&adv7482_i2s>;
+
+				dai-tdm-slot-num = <8>;
+				dai-tdm-slot-width = <32>;
+				dai-format = "left_j";
+				mclk-fs = <256>;
+				bitclock-master = <&adv7482_i2s>;
+				frame-master = <&adv7482_i2s>;
+				system-clock-direction-out;
+
+				capture = <&ssi4>;
+			};
+		};
 	};
 };
 
+&adv7482_i2s {
+	remote-endpoint = <&rsnd_endpoint3>;
+};
+
 &sata {
 	status = "okay";
 };
@@ -146,9 +166,11 @@
 &sound_card {
 	dais = <&rsnd_port0	/* ak4613 */
 		&rsnd_port1	/* HDMI0  */
-		&rsnd_port2>;	/* HDMI1  */
+		&rsnd_port2	/* HDMI1  */
+		&rsnd_port3>;	/* adv7482 hdmi-in  */
 };
 
+
 &usb2_phy2 {
 	pinctrl-0 = <&usb2_pins>;
 	pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/renesas/salvator-common.dtsi b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
index 21e01056e759..e887805b16fc 100644
--- a/arch/arm64/boot/dts/renesas/salvator-common.dtsi
+++ b/arch/arm64/boot/dts/renesas/salvator-common.dtsi
@@ -322,6 +322,10 @@
 	clock-frequency = <22579200>;
 };
 
+&audio_clk_c {
+	clock-frequency = <12288000>;
+};
+
 &avb {
 	pinctrl-0 = <&avb_pins>;
 	pinctrl-names = "default";
@@ -471,12 +475,14 @@
 
 		#address-cells = <1>;
 		#size-cells = <0>;
+		#sound-dai-cells = <0>;
 
 		interrupt-parent = <&gpio6>;
 		interrupt-names = "intrq1", "intrq2";
 		interrupts = <30 IRQ_TYPE_LEVEL_LOW>,
 			     <31 IRQ_TYPE_LEVEL_LOW>;
-
+		clocks = <&rcar_sound 3>, <&audio_clk_c>;
+		clock-names = "clk-hdmi-video", "clk-hdmi-i2s-mclk";
 		port@7 {
 			reg = <7>;
 
@@ -512,6 +518,14 @@
 				remote-endpoint = <&csi20_in>;
 			};
 		};
+
+		port@c {
+			reg = <12>;
+
+			adv7482_i2s: endpoint {
+				/* remote-endpoint defined in the board file */
+			};
+		};
 	};
 
 	csa_vdd: adc@7c {
@@ -686,7 +700,8 @@
 	};
 
 	sound_pins: sound {
-		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a";
+		groups = "ssi01239_ctrl", "ssi0_data", "ssi1_data_a",
+			 "ssi4_data";
 		function = "ssi";
 	};
 
@@ -735,8 +750,8 @@
 	pinctrl-0 = <&sound_pins &sound_clk_pins>;
 	pinctrl-names = "default";
 
-	/* Single DAI */
-	#sound-dai-cells = <0>;
+	/* multi DAI */
+	#sound-dai-cells = <1>;
 
 	/* audio_clkout0/1/2/3 */
 	#clock-cells = <1>;
@@ -760,8 +775,18 @@
 		 <&cpg CPG_MOD 1020>, <&cpg CPG_MOD 1021>,
 		 <&cpg CPG_MOD 1019>, <&cpg CPG_MOD 1018>,
 		 <&audio_clk_a>, <&cs2000>,
-		 <&audio_clk_c>,
 		 <&cpg CPG_CORE CPG_AUDIO_CLK_I>;
+	clock-names = "ssi-all",
+		      "ssi.9", "ssi.8", "ssi.7", "ssi.6",
+		      "ssi.5", "ssi.4", "ssi.3", "ssi.2",
+		      "ssi.1", "ssi.0",
+		      "src.9", "src.8", "src.7", "src.6",
+		      "src.5", "src.4", "src.3", "src.2",
+		      "src.1", "src.0",
+		      "mix.1", "mix.0",
+		      "ctu.1", "ctu.0",
+		      "dvc.0", "dvc.1",
+		      "clk_a", "clk_b", "clk_i";
 
 	ports {
 		#address-cells = <1>;
-- 
2.24.1.508.g91d2dafee0

  parent reply	other threads:[~2020-01-13 14:24 UTC|newest]

Thread overview: 31+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-01-13 14:19 [PATCH 0/8] media: i2c: adv748x: add support for HDMI audio Alex Riesen
2020-01-13 14:15 ` [PATCH 1/8] media: adv748x: add a device-specific wrapper for register block read Alex Riesen
2020-01-13 14:15 ` [PATCH 2/8] media: adv748x: add audio mute control and output selection ioctls Alex Riesen
2020-03-13  8:16   ` Hans Verkuil
2020-03-13 10:26     ` Alex Riesen
2020-03-13 10:52       ` Hans Verkuil
2020-03-13 11:00         ` Alex Riesen
2020-01-13 14:15 ` [PATCH 3/8] media: adv748x: add log_status ioctl Alex Riesen
2020-01-13 14:15 ` [PATCH 4/8] media: adv748x: reserve space for the audio (I2S) port in the driver structures Alex Riesen
2020-01-13 14:15 ` [PATCH 5/8] media: adv748x: add an ASoC DAI definition to the driver Alex Riesen
2020-01-13 14:15 ` [PATCH 6/8] media: adv748x: reduce amount of code for bitwise modification of device registers Alex Riesen
2020-01-13 14:15 ` [PATCH 7/8] dt-bindings: adv748x: add information about serial audio interface (I2S/TDM) Alex Riesen
2020-01-13 22:32   ` Rob Herring
2020-01-13 14:15 ` Alex Riesen [this message]
2020-03-02 12:28   ` [PATCH 8/8] arm64: dts: renesas: salvator: add a connection from adv748x codec (HDMI input) to the R-Car SoC Geert Uytterhoeven
2020-03-02 13:40     ` Alex Riesen
2020-03-02 13:47       ` Geert Uytterhoeven
2020-03-02 15:07         ` Alex Riesen
2020-03-02 15:32           ` Geert Uytterhoeven
2020-03-02 16:09             ` Alex Riesen
2020-03-02 16:13               ` Geert Uytterhoeven
2020-03-05 14:36                 ` Alex Riesen
2020-03-06 12:21                   ` Geert Uytterhoeven
2020-03-06 13:16                   ` Laurent Pinchart
2020-03-06 13:41                     ` Alex Riesen
2020-03-06 13:45                       ` Laurent Pinchart
2020-03-09  1:31                         ` Kuninori Morimoto
2020-03-09 11:09                           ` Alex Riesen
2020-03-10  1:07                             ` Kuninori Morimoto
2020-03-10  8:17                               ` Alex Riesen
2020-03-10 10:39                                 ` Laurent Pinchart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20200113141556.GI3606@pflmari \
    --to=alexander.riesen@cetitec.com \
    --cc=devel@driverdev.osuosl.org \
    --cc=devicetree@vger.kernel.org \
    --cc=hverkuil-cisco@xs4all.nl \
    --cc=kieran.bingham@ideasonboard.com \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=mark.rutland@arm.com \
    --cc=mchehab@kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).