From: Sam Ravnborg <sam@ravnborg.org>
To: Geert Uytterhoeven <geert+renesas@glider.be>
Cc: "Noralf Trønnes" <noralf@tronnes.org>,
"David Lechner" <david@lechnology.com>,
"David Airlie" <airlied@linux.ie>,
"Daniel Vetter" <daniel@ffwll.ch>,
"Maarten Lankhorst" <maarten.lankhorst@linux.intel.com>,
"Maxime Ripard" <mripard@kernel.org>,
"Rob Herring" <robh+dt@kernel.org>,
"Mark Rutland" <mark.rutland@arm.com>,
"Chris Brandt" <chris.brandt@renesas.com>,
"Kieran Bingham" <kieran.bingham+renesas@ideasonboard.com>,
dri-devel@lists.freedesktop.org, devicetree@vger.kernel.org,
linux-renesas-soc@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH v2 0/5] drm: Add support for Okaya RH128128T
Date: Sun, 19 Jan 2020 18:15:55 +0100 [thread overview]
Message-ID: <20200119171555.GA31055@ravnborg.org> (raw)
In-Reply-To: <20200115124548.3951-1-geert+renesas@glider.be>
Hi Geert.
On Wed, Jan 15, 2020 at 01:45:43PM +0100, Geert Uytterhoeven wrote:
> Hi all,
>
> This patch series adds support for the Okaya RH128128T LCD to the
> existing ST7735R driver. This is a 128x128 1.4" TFT display driven by a
> Sitronix ST7715R TFT Controller/Driver. It is used on e.g. the Renesas
> YRSK-LCD-PMOD extension board, which is shipped with Renesas RSK+RZA1
> development boards[1], and with several other Renesas starter kits, for
> RX, Synergy, and RZ/T1 MCUs and SoCs.
>
> Changes compared to v1[2]:
> - Convert DT bindings to DT schema,
> - Add YRSK-LCD-PMOD reference and links,
> - Add Reviewed-by,
> - Split driver preparation and adding actual support in two separate
> patches,
> - Replace st7735r_priv.rgb by a pointer to struct st7735r_cfg,
> - Change prefix of jd_t18003_t01_pipe_enable() and
> jd_t18003_t01_pipe_funcs(),
> - Update Kconfig help text,
> - Improve file comment header.
>
> This has been tested using the r7s72100-rskrza1-pmod-spi.dtso and
> r7s72100-rskrza1-pmod2-lcd.dtso DT overlays[3].
> Note that for using this on RSK+RZA1, there is a dependency on RSPI
> cs-gpios support (now in linux-next).
> With DT overlays, this also depends on DT overlays[4] and gpio-hog
> overlay support[5].
>
> Thanks!
>
> [1] https://renesasrulz.com/the_vault/f/archive-forum/4981/upgrading-to-the-renesas-rz-a1h
> [1] https://lore.kernel.org/dri-devel/20200102141246.370-1-geert+renesas@glider.be/
> [2] https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git/log/?h=topic/renesas-overlays
> [4] https://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-drivers.git/log/?h=topic/overlays
> [5] "[PATCH/RFC 0/2] gpio: of: Add DT overlay support for GPIO hogs"
> https://lore.kernel.org/lkml/20191230133852.5890-1-geert+renesas@glider.be/
>
> Geert Uytterhoeven (5):
> dt-bindings: display: sitronix,st7735r: Convert to DT schema
> dt-bindings: display: sitronix,st7735r: Add Okaya RH128128T
> drm/mipi_dbi: Add support for display offsets
> drm: tiny: st7735r: Prepare for adding support for more displays
> drm: tiny: st7735r: Add support for Okaya RH128128T
Thanks, it ended up with a nice small patch adding support for
another controller/panel combo to this driver.
All 5 patches applied to drm-misc-next.
Sam
prev parent reply other threads:[~2020-01-19 17:16 UTC|newest]
Thread overview: 18+ messages / expand[flat|nested] mbox.gz Atom feed top
2020-01-15 12:45 [PATCH v2 0/5] drm: Add support for Okaya RH128128T Geert Uytterhoeven
2020-01-15 12:45 ` [PATCH v2 1/5] dt-bindings: display: sitronix,st7735r: Convert to DT schema Geert Uytterhoeven
2020-01-15 21:01 ` Sam Ravnborg
2020-01-15 22:06 ` Geert Uytterhoeven
2020-01-20 16:00 ` David Lechner
2020-01-20 19:02 ` [PATCH] dt-bindings: restrict properties for sitronix,st7735r Sam Ravnborg
2020-01-23 7:24 ` Sam Ravnborg
2020-01-23 7:43 ` Geert Uytterhoeven
2020-01-23 18:19 ` Sam Ravnborg
2020-01-23 14:41 ` Rob Herring
2020-01-15 12:45 ` [PATCH v2 2/5] dt-bindings: display: sitronix,st7735r: Add Okaya RH128128T Geert Uytterhoeven
2020-01-15 21:01 ` Sam Ravnborg
2020-01-15 12:45 ` [PATCH v2 3/5] drm/mipi_dbi: Add support for display offsets Geert Uytterhoeven
2020-01-17 21:12 ` Sam Ravnborg
2020-01-19 16:03 ` Noralf Trønnes
2020-01-15 12:45 ` [PATCH v2 4/5] drm: tiny: st7735r: Prepare for adding support for more displays Geert Uytterhoeven
2020-01-15 12:45 ` [PATCH v2 5/5] drm: tiny: st7735r: Add support for Okaya RH128128T Geert Uytterhoeven
2020-01-19 17:15 ` Sam Ravnborg [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20200119171555.GA31055@ravnborg.org \
--to=sam@ravnborg.org \
--cc=airlied@linux.ie \
--cc=chris.brandt@renesas.com \
--cc=daniel@ffwll.ch \
--cc=david@lechnology.com \
--cc=devicetree@vger.kernel.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=geert+renesas@glider.be \
--cc=kieran.bingham+renesas@ideasonboard.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=mark.rutland@arm.com \
--cc=mripard@kernel.org \
--cc=noralf@tronnes.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).