* [PATCH AUTOSEL 4.14 013/186] pinctrl: sh-pfc: sh7264: Fix CAN function GPIOs
[not found] <20200214161715.18113-1-sashal@kernel.org>
@ 2020-02-14 16:14 ` Sasha Levin
2020-02-14 16:15 ` [PATCH AUTOSEL 4.14 088/186] ARM: dts: r8a7779: Add device node for ARM global timer Sasha Levin
` (2 subsequent siblings)
3 siblings, 0 replies; 4+ messages in thread
From: Sasha Levin @ 2020-02-14 16:14 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Geert Uytterhoeven, Sasha Levin, linux-renesas-soc, linux-gpio
From: Geert Uytterhoeven <geert+renesas@glider.be>
[ Upstream commit 55b1cb1f03ad5eea39897d0c74035e02deddcff2 ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
two CAN outputs.
Fix this by:
- Renaming CRX0_CRX1_MARK to CTX0_CTX1_MARK, as PJ2MD[2:0]=010
configures the combined "CTX0&CTX1" output signal,
- Renaming CRX0X1_MARK to CRX0_CRX1_MARK, as PJ3MD[1:0]=10 configures
the shared "CRX0/CRX1" input signal, which is fed to both CAN
inputs,
- Adding the missing function GPIO definition for "CTX0&CTX1" to
pinmux_func_gpios[],
- Moving all CAN enums next to each other.
See SH7262 Group, SH7264 Group User's Manual: Hardware, Rev. 4.00:
[1] Figure 1.2 (3) (Pin Assignment for the SH7264 Group (1-Mbyte
Version),
[2] Figure 1.2 (4) Pin Assignment for the SH7264 Group (640-Kbyte
Version,
[3] Table 1.4 List of Pins,
[4] Figure 20.29 Connection Example when Using This Module as 1-Channel
Module (64 Mailboxes x 1 Channel),
[5] Table 32.10 Multiplexed Pins (Port J),
[6] Section 32.2.30 (3) Port J Control Register 0 (PJCR0).
Note that the last 2 disagree about PJ2MD[2:0], which is probably the
root cause of this bug. But considering [4], "CTx0&CTx1" in [5] must
be correct, and "CRx0&CRx1" in [6] must be wrong.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-4-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/pinctrl/sh-pfc/pfc-sh7264.c | 9 ++++-----
1 file changed, 4 insertions(+), 5 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/pfc-sh7264.c b/drivers/pinctrl/sh-pfc/pfc-sh7264.c
index e1c34e19222ee..3ddb9565ed804 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh7264.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh7264.c
@@ -500,17 +500,15 @@ enum {
SD_WP_MARK, SD_CLK_MARK, SD_CMD_MARK,
CRX0_MARK, CRX1_MARK,
CTX0_MARK, CTX1_MARK,
+ CRX0_CRX1_MARK, CTX0_CTX1_MARK,
PWM1A_MARK, PWM1B_MARK, PWM1C_MARK, PWM1D_MARK,
PWM1E_MARK, PWM1F_MARK, PWM1G_MARK, PWM1H_MARK,
PWM2A_MARK, PWM2B_MARK, PWM2C_MARK, PWM2D_MARK,
PWM2E_MARK, PWM2F_MARK, PWM2G_MARK, PWM2H_MARK,
IERXD_MARK, IETXD_MARK,
- CRX0_CRX1_MARK,
WDTOVF_MARK,
- CRX0X1_MARK,
-
/* DMAC */
TEND0_MARK, DACK0_MARK, DREQ0_MARK,
TEND1_MARK, DACK1_MARK, DREQ1_MARK,
@@ -998,12 +996,12 @@ static const u16 pinmux_data[] = {
PINMUX_DATA(PJ3_DATA, PJ3MD_00),
PINMUX_DATA(CRX1_MARK, PJ3MD_01),
- PINMUX_DATA(CRX0X1_MARK, PJ3MD_10),
+ PINMUX_DATA(CRX0_CRX1_MARK, PJ3MD_10),
PINMUX_DATA(IRQ1_PJ_MARK, PJ3MD_11),
PINMUX_DATA(PJ2_DATA, PJ2MD_000),
PINMUX_DATA(CTX1_MARK, PJ2MD_001),
- PINMUX_DATA(CRX0_CRX1_MARK, PJ2MD_010),
+ PINMUX_DATA(CTX0_CTX1_MARK, PJ2MD_010),
PINMUX_DATA(CS2_MARK, PJ2MD_011),
PINMUX_DATA(SCK0_MARK, PJ2MD_100),
PINMUX_DATA(LCD_M_DISP_MARK, PJ2MD_101),
@@ -1248,6 +1246,7 @@ static const struct pinmux_func pinmux_func_gpios[] = {
GPIO_FN(CTX1),
GPIO_FN(CRX1),
GPIO_FN(CTX0),
+ GPIO_FN(CTX0_CTX1),
GPIO_FN(CRX0),
GPIO_FN(CRX0_CRX1),
--
2.20.1
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH AUTOSEL 4.14 094/186] pinctrl: sh-pfc: r8a7778: Fix duplicate SDSELF_B and SD1_CLK_B
[not found] <20200214161715.18113-1-sashal@kernel.org>
2020-02-14 16:14 ` [PATCH AUTOSEL 4.14 013/186] pinctrl: sh-pfc: sh7264: Fix CAN function GPIOs Sasha Levin
2020-02-14 16:15 ` [PATCH AUTOSEL 4.14 088/186] ARM: dts: r8a7779: Add device node for ARM global timer Sasha Levin
@ 2020-02-14 16:15 ` Sasha Levin
2020-02-14 16:15 ` [PATCH AUTOSEL 4.14 095/186] pinctrl: sh-pfc: sh7269: Fix CAN function GPIOs Sasha Levin
3 siblings, 0 replies; 4+ messages in thread
From: Sasha Levin @ 2020-02-14 16:15 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Geert Uytterhoeven, Sasha Levin, linux-renesas-soc, linux-gpio
From: Geert Uytterhoeven <geert+renesas@glider.be>
[ Upstream commit 805f635703b2562b5ddd822c62fc9124087e5dd5 ]
The FN_SDSELF_B and FN_SD1_CLK_B enum IDs are used twice, which means
one set of users must be wrong. Replace them by the correct enum IDs.
Fixes: 87f8c988636db0d4 ("sh-pfc: Add r8a7778 pinmux support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-2-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
drivers/pinctrl/sh-pfc/pfc-r8a7778.c | 4 ++--
1 file changed, 2 insertions(+), 2 deletions(-)
diff --git a/drivers/pinctrl/sh-pfc/pfc-r8a7778.c b/drivers/pinctrl/sh-pfc/pfc-r8a7778.c
index c3af9ebee4afc..28c0405ba396f 100644
--- a/drivers/pinctrl/sh-pfc/pfc-r8a7778.c
+++ b/drivers/pinctrl/sh-pfc/pfc-r8a7778.c
@@ -2325,7 +2325,7 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
FN_ATAG0_A, 0, FN_REMOCON_B, 0,
/* IP0_11_8 [4] */
FN_SD1_DAT2_A, FN_MMC_D2, 0, FN_BS,
- FN_ATADIR0_A, 0, FN_SDSELF_B, 0,
+ FN_ATADIR0_A, 0, FN_SDSELF_A, 0,
FN_PWM4_B, 0, 0, 0,
0, 0, 0, 0,
/* IP0_7_5 [3] */
@@ -2367,7 +2367,7 @@ static const struct pinmux_cfg_reg pinmux_config_regs[] = {
FN_TS_SDAT0_A, 0, 0, 0,
0, 0, 0, 0,
/* IP1_10_8 [3] */
- FN_SD1_CLK_B, FN_MMC_D6, 0, FN_A24,
+ FN_SD1_CD_A, FN_MMC_D6, 0, FN_A24,
FN_DREQ1_A, 0, FN_HRX0_B, FN_TS_SPSYNC0_A,
/* IP1_7_5 [3] */
FN_A23, FN_HTX0_B, FN_TX2_B, FN_DACK2_A,
--
2.20.1
^ permalink raw reply related [flat|nested] 4+ messages in thread* [PATCH AUTOSEL 4.14 095/186] pinctrl: sh-pfc: sh7269: Fix CAN function GPIOs
[not found] <20200214161715.18113-1-sashal@kernel.org>
` (2 preceding siblings ...)
2020-02-14 16:15 ` [PATCH AUTOSEL 4.14 094/186] pinctrl: sh-pfc: r8a7778: Fix duplicate SDSELF_B and SD1_CLK_B Sasha Levin
@ 2020-02-14 16:15 ` Sasha Levin
3 siblings, 0 replies; 4+ messages in thread
From: Sasha Levin @ 2020-02-14 16:15 UTC (permalink / raw)
To: linux-kernel, stable
Cc: Geert Uytterhoeven, Sasha Levin, linux-sh, linux-renesas-soc, linux-gpio
From: Geert Uytterhoeven <geert+renesas@glider.be>
[ Upstream commit 02aeb2f21530c98fc3ca51028eda742a3fafbd9f ]
pinmux_func_gpios[] contains a hole due to the missing function GPIO
definition for the "CTX0&CTX1" signal, which is the logical "AND" of the
first two CAN outputs.
A closer look reveals other issues:
- Some functionality is available on alternative pins, but the
PINMUX_DATA() entries is using the wrong marks,
- Several configurations are missing.
Fix this by:
- Renaming CTX0CTX1CTX2_MARK, CRX0CRX1_PJ22_MARK, and
CRX0CRX1CRX2_PJ20_MARK to CTX0_CTX1_CTX2_MARK, CRX0_CRX1_PJ22_MARK,
resp. CRX0_CRX1_CRX2_PJ20_MARK for consistency with the
corresponding enum IDs,
- Adding all missing enum IDs and marks,
- Use the right (*_PJ2x) variants for alternative pins,
- Adding all missing configurations to pinmux_data[],
- Adding all missing function GPIO definitions to pinmux_func_gpios[].
See SH7268 Group, SH7269 Group User’s Manual: Hardware, Rev. 2.00:
[1] Table 1.4 List of Pins
[2] Figure 23.29 Connection Example when Using Channels 0 and 1 as One
Channel (64 Mailboxes × 1 Channel) and Channel 2 as One Channel
(32 Mailboxes × 1 Channel),
[3] Figure 23.30 Connection Example when Using Channels 0, 1, and 2 as
One Channel (96 Mailboxes × 1 Channel),
[4] Table 48.3 Multiplexed Pins (Port B),
[5] Table 48.4 Multiplexed Pins (Port C),
[6] Table 48.10 Multiplexed Pins (Port J),
[7] Section 48.2.4 Port B Control Registers 0 to 5 (PBCR0 to PBCR5).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20191218194812.12741-5-geert+renesas@glider.be
Signed-off-by: Sasha Levin <sashal@kernel.org>
---
arch/sh/include/cpu-sh2a/cpu/sh7269.h | 11 ++++++--
drivers/pinctrl/sh-pfc/pfc-sh7269.c | 39 ++++++++++++++++++---------
2 files changed, 36 insertions(+), 14 deletions(-)
diff --git a/arch/sh/include/cpu-sh2a/cpu/sh7269.h b/arch/sh/include/cpu-sh2a/cpu/sh7269.h
index d516e5d488180..b887cc402b712 100644
--- a/arch/sh/include/cpu-sh2a/cpu/sh7269.h
+++ b/arch/sh/include/cpu-sh2a/cpu/sh7269.h
@@ -78,8 +78,15 @@ enum {
GPIO_FN_WDTOVF,
/* CAN */
- GPIO_FN_CTX1, GPIO_FN_CRX1, GPIO_FN_CTX0, GPIO_FN_CTX0_CTX1,
- GPIO_FN_CRX0, GPIO_FN_CRX0_CRX1, GPIO_FN_CRX0_CRX1_CRX2,
+ GPIO_FN_CTX2, GPIO_FN_CRX2,
+ GPIO_FN_CTX1, GPIO_FN_CRX1,
+ GPIO_FN_CTX0, GPIO_FN_CRX0,
+ GPIO_FN_CTX0_CTX1, GPIO_FN_CRX0_CRX1,
+ GPIO_FN_CTX0_CTX1_CTX2, GPIO_FN_CRX0_CRX1_CRX2,
+ GPIO_FN_CTX2_PJ21, GPIO_FN_CRX2_PJ20,
+ GPIO_FN_CTX1_PJ23, GPIO_FN_CRX1_PJ22,
+ GPIO_FN_CTX0_CTX1_PJ23, GPIO_FN_CRX0_CRX1_PJ22,
+ GPIO_FN_CTX0_CTX1_CTX2_PJ21, GPIO_FN_CRX0_CRX1_CRX2_PJ20,
/* DMAC */
GPIO_FN_TEND0, GPIO_FN_DACK0, GPIO_FN_DREQ0,
diff --git a/drivers/pinctrl/sh-pfc/pfc-sh7269.c b/drivers/pinctrl/sh-pfc/pfc-sh7269.c
index cfdb4fc177c3e..3df0c0d139d08 100644
--- a/drivers/pinctrl/sh-pfc/pfc-sh7269.c
+++ b/drivers/pinctrl/sh-pfc/pfc-sh7269.c
@@ -740,13 +740,12 @@ enum {
CRX0_MARK, CTX0_MARK,
CRX1_MARK, CTX1_MARK,
CRX2_MARK, CTX2_MARK,
- CRX0_CRX1_MARK,
- CRX0_CRX1_CRX2_MARK,
- CTX0CTX1CTX2_MARK,
+ CRX0_CRX1_MARK, CTX0_CTX1_MARK,
+ CRX0_CRX1_CRX2_MARK, CTX0_CTX1_CTX2_MARK,
CRX1_PJ22_MARK, CTX1_PJ23_MARK,
CRX2_PJ20_MARK, CTX2_PJ21_MARK,
- CRX0CRX1_PJ22_MARK,
- CRX0CRX1CRX2_PJ20_MARK,
+ CRX0_CRX1_PJ22_MARK, CTX0_CTX1_PJ23_MARK,
+ CRX0_CRX1_CRX2_PJ20_MARK, CTX0_CTX1_CTX2_PJ21_MARK,
/* VDC */
DV_CLK_MARK,
@@ -824,6 +823,7 @@ static const u16 pinmux_data[] = {
PINMUX_DATA(CS3_MARK, PC8MD_001),
PINMUX_DATA(TXD7_MARK, PC8MD_010),
PINMUX_DATA(CTX1_MARK, PC8MD_011),
+ PINMUX_DATA(CTX0_CTX1_MARK, PC8MD_100),
PINMUX_DATA(PC7_DATA, PC7MD_000),
PINMUX_DATA(CKE_MARK, PC7MD_001),
@@ -836,11 +836,12 @@ static const u16 pinmux_data[] = {
PINMUX_DATA(CAS_MARK, PC6MD_001),
PINMUX_DATA(SCK7_MARK, PC6MD_010),
PINMUX_DATA(CTX0_MARK, PC6MD_011),
+ PINMUX_DATA(CTX0_CTX1_CTX2_MARK, PC6MD_100),
PINMUX_DATA(PC5_DATA, PC5MD_000),
PINMUX_DATA(RAS_MARK, PC5MD_001),
PINMUX_DATA(CRX0_MARK, PC5MD_011),
- PINMUX_DATA(CTX0CTX1CTX2_MARK, PC5MD_100),
+ PINMUX_DATA(CTX0_CTX1_CTX2_MARK, PC5MD_100),
PINMUX_DATA(IRQ0_PC_MARK, PC5MD_101),
PINMUX_DATA(PC4_DATA, PC4MD_00),
@@ -1292,30 +1293,32 @@ static const u16 pinmux_data[] = {
PINMUX_DATA(LCD_DATA23_PJ23_MARK, PJ23MD_010),
PINMUX_DATA(LCD_TCON6_MARK, PJ23MD_011),
PINMUX_DATA(IRQ3_PJ_MARK, PJ23MD_100),
- PINMUX_DATA(CTX1_MARK, PJ23MD_101),
+ PINMUX_DATA(CTX1_PJ23_MARK, PJ23MD_101),
+ PINMUX_DATA(CTX0_CTX1_PJ23_MARK, PJ23MD_110),
PINMUX_DATA(PJ22_DATA, PJ22MD_000),
PINMUX_DATA(DV_DATA22_MARK, PJ22MD_001),
PINMUX_DATA(LCD_DATA22_PJ22_MARK, PJ22MD_010),
PINMUX_DATA(LCD_TCON5_MARK, PJ22MD_011),
PINMUX_DATA(IRQ2_PJ_MARK, PJ22MD_100),
- PINMUX_DATA(CRX1_MARK, PJ22MD_101),
- PINMUX_DATA(CRX0_CRX1_MARK, PJ22MD_110),
+ PINMUX_DATA(CRX1_PJ22_MARK, PJ22MD_101),
+ PINMUX_DATA(CRX0_CRX1_PJ22_MARK, PJ22MD_110),
PINMUX_DATA(PJ21_DATA, PJ21MD_000),
PINMUX_DATA(DV_DATA21_MARK, PJ21MD_001),
PINMUX_DATA(LCD_DATA21_PJ21_MARK, PJ21MD_010),
PINMUX_DATA(LCD_TCON4_MARK, PJ21MD_011),
PINMUX_DATA(IRQ1_PJ_MARK, PJ21MD_100),
- PINMUX_DATA(CTX2_MARK, PJ21MD_101),
+ PINMUX_DATA(CTX2_PJ21_MARK, PJ21MD_101),
+ PINMUX_DATA(CTX0_CTX1_CTX2_PJ21_MARK, PJ21MD_110),
PINMUX_DATA(PJ20_DATA, PJ20MD_000),
PINMUX_DATA(DV_DATA20_MARK, PJ20MD_001),
PINMUX_DATA(LCD_DATA20_PJ20_MARK, PJ20MD_010),
PINMUX_DATA(LCD_TCON3_MARK, PJ20MD_011),
PINMUX_DATA(IRQ0_PJ_MARK, PJ20MD_100),
- PINMUX_DATA(CRX2_MARK, PJ20MD_101),
- PINMUX_DATA(CRX0CRX1CRX2_PJ20_MARK, PJ20MD_110),
+ PINMUX_DATA(CRX2_PJ20_MARK, PJ20MD_101),
+ PINMUX_DATA(CRX0_CRX1_CRX2_PJ20_MARK, PJ20MD_110),
PINMUX_DATA(PJ19_DATA, PJ19MD_000),
PINMUX_DATA(DV_DATA19_MARK, PJ19MD_001),
@@ -1666,12 +1669,24 @@ static const struct pinmux_func pinmux_func_gpios[] = {
GPIO_FN(WDTOVF),
/* CAN */
+ GPIO_FN(CTX2),
+ GPIO_FN(CRX2),
GPIO_FN(CTX1),
GPIO_FN(CRX1),
GPIO_FN(CTX0),
GPIO_FN(CRX0),
+ GPIO_FN(CTX0_CTX1),
GPIO_FN(CRX0_CRX1),
+ GPIO_FN(CTX0_CTX1_CTX2),
GPIO_FN(CRX0_CRX1_CRX2),
+ GPIO_FN(CTX2_PJ21),
+ GPIO_FN(CRX2_PJ20),
+ GPIO_FN(CTX1_PJ23),
+ GPIO_FN(CRX1_PJ22),
+ GPIO_FN(CTX0_CTX1_PJ23),
+ GPIO_FN(CRX0_CRX1_PJ22),
+ GPIO_FN(CTX0_CTX1_CTX2_PJ21),
+ GPIO_FN(CRX0_CRX1_CRX2_PJ20),
/* DMAC */
GPIO_FN(TEND0),
--
2.20.1
^ permalink raw reply related [flat|nested] 4+ messages in thread