Linux-Renesas-SoC Archive on lore.kernel.org
 help / color / Atom feed
From: "Lad, Prabhakar" <prabhakar.csengg@gmail.com>
To: Sakari Ailus <sakari.ailus@linux.intel.com>
Cc: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>,
	Jacopo Mondi <jacopo@jmondi.org>,
	Mauro Carvalho Chehab <mchehab@kernel.org>,
	Steve Longerbeam <slongerbeam@gmail.com>,
	linux-media <linux-media@vger.kernel.org>,
	Hugues Fruchet <hugues.fruchet@st.com>,
	Laurent Pinchart <laurent.pinchart@ideasonboard.com>,
	Linux-Renesas <linux-renesas-soc@vger.kernel.org>,
	LKML <linux-kernel@vger.kernel.org>,
	Biju Das <biju.das.jz@bp.renesas.com>
Subject: Re: [PATCH 1/2] media: i2c: ov5640: Enable data pins on startup for DVP mode
Date: Fri, 31 Jul 2020 16:23:13 +0100
Message-ID: <CA+V-a8srhDcjjHe73UBTxqz8jooNp4nLvaScLY5jFSNtwYkCcg@mail.gmail.com> (raw)
In-Reply-To: <20200731151927.GR13316@paasikivi.fi.intel.com>

Hi Sakari,

On Fri, Jul 31, 2020 at 4:19 PM Sakari Ailus
<sakari.ailus@linux.intel.com> wrote:
>
> Hi Prabhakar,
>
> On Fri, Jul 31, 2020 at 02:18:12PM +0100, Lad, Prabhakar wrote:
> > Hi Sakari,
> >
> > Thank you for the review.
> >
> > On Fri, Jul 31, 2020 at 2:03 PM Sakari Ailus
> > <sakari.ailus@linux.intel.com> wrote:
> > >
> > > Hi Prabhakar,
> > >
> > > Thank you for the patch.
> > >
> > > On Fri, Jul 31, 2020 at 10:24:46AM +0100, Lad Prabhakar wrote:
> > > > During testing this sensor on iW-RainboW-G21D-Qseven platform noticed the
> > > > capture worked only for first run and for subsequent runs it failed.
> > > >
> > > > This patch does the following in DVP mode:
> > > > 1: Enables data lines on power up
> > > > 2: Configures HVP lines on power up instead of configuring everytime on
> > > >    stream ON/OFF
> > > > 3: Disables MIPI interface.
> > > > 4: Puts the sensor in power down mode during stream OFF.
>
> Does this last one only apply to DVP (parallel) mode?
>
Yes only in DVP mode.

> > >
> > > Could you detail a little the underlying problem, the environment where it
> > > can be reproduced and how the patch addresses it, please?
> > >
> > my bad.
> >
> > > Are you using CSI-2 or the parallel interface, for instance?
> > >
> > while using the sensor in parallel interface mode (DVP) 8-bit mode,
> > with rcar-vin bridge noticed the capture worked fine for the first run
> > (with yavta), but for subsequent runs the bridge driver waited for the
> > frame to be captured. Debugging further noticed the data lines were
> > enabled/disabled in stream on/off callback. But enabling the data
> > lines in startup (as done in the patch) fixed this issue.
>
> Could you add a note on this bug to the commit message, please?
>
Sure will do.

> >
> > Without this patch I can confirm the i2c writes were happening in
> > stream on/off callback and the values were updated in the respective
> > register to enable/disable datalines. (I didn't find any information
> > relating to sequence of enabling the data lines in data sheet [1])
> >
> > [1] https://cdn.sparkfun.com/datasheets/Sensors/LightImaging/OV5640_datasheet.pdf
> >
> > > >
> > > > Fixes: f22996db44e2d ("media: ov5640: add support of DVP parallel interface")
> > > > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
> > > > Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
> > > > ---
> > > >  drivers/media/i2c/ov5640.c | 253 +++++++++++++++++++++------------------------
> > > >  1 file changed, 120 insertions(+), 133 deletions(-)
> > > >
> > > > diff --git a/drivers/media/i2c/ov5640.c b/drivers/media/i2c/ov5640.c
> > > > index 2fe4a7a..ac305a5 100644
> > > > --- a/drivers/media/i2c/ov5640.c
> > > > +++ b/drivers/media/i2c/ov5640.c
> > > > @@ -274,7 +274,7 @@ static inline struct v4l2_subdev *ctrl_to_sd(struct v4l2_ctrl *ctrl)
> > > >  /* YUV422 UYVY VGA@30fps */
> > > >  static const struct reg_value ov5640_init_setting_30fps_VGA[] = {
> > > >       {0x3103, 0x11, 0, 0}, {0x3008, 0x82, 0, 5}, {0x3008, 0x42, 0, 0},
> > > > -     {0x3103, 0x03, 0, 0}, {0x3017, 0x00, 0, 0}, {0x3018, 0x00, 0, 0},
> > > > +     {0x3103, 0x03, 0, 0},
> > > >       {0x3630, 0x36, 0, 0},
> > > >       {0x3631, 0x0e, 0, 0}, {0x3632, 0xe2, 0, 0}, {0x3633, 0x12, 0, 0},
> > > >       {0x3621, 0xe0, 0, 0}, {0x3704, 0xa0, 0, 0}, {0x3703, 0x5a, 0, 0},
> > > > @@ -1210,96 +1210,7 @@ static int ov5640_set_autogain(struct ov5640_dev *sensor, bool on)
> > > >
> > > >  static int ov5640_set_stream_dvp(struct ov5640_dev *sensor, bool on)
> > > >  {
> > > > -     int ret;
> > > > -     unsigned int flags = sensor->ep.bus.parallel.flags;
> > > > -     u8 pclk_pol = 0;
> > > > -     u8 hsync_pol = 0;
> > > > -     u8 vsync_pol = 0;
> > > > -
> > > > -     /*
> > > > -      * Note about parallel port configuration.
> > > > -      *
> > > > -      * When configured in parallel mode, the OV5640 will
> > > > -      * output 10 bits data on DVP data lines [9:0].
> > > > -      * If only 8 bits data are wanted, the 8 bits data lines
> > > > -      * of the camera interface must be physically connected
> > > > -      * on the DVP data lines [9:2].
> > > > -      *
> > > > -      * Control lines polarity can be configured through
> > > > -      * devicetree endpoint control lines properties.
> > > > -      * If no endpoint control lines properties are set,
> > > > -      * polarity will be as below:
> > > > -      * - VSYNC:     active high
> > > > -      * - HREF:      active low
> > > > -      * - PCLK:      active low
> > > > -      */
> > > > -
> > > > -     if (on) {
> > > > -             /*
> > > > -              * configure parallel port control lines polarity
> > > > -              *
> > > > -              * POLARITY CTRL0
> > > > -              * - [5]:       PCLK polarity (0: active low, 1: active high)
> > > > -              * - [1]:       HREF polarity (0: active low, 1: active high)
> > > > -              * - [0]:       VSYNC polarity (mismatch here between
> > > > -              *              datasheet and hardware, 0 is active high
> > > > -              *              and 1 is active low...)
> > > > -              */
> > > > -             if (flags & V4L2_MBUS_PCLK_SAMPLE_RISING)
> > > > -                     pclk_pol = 1;
> > > > -             if (flags & V4L2_MBUS_HSYNC_ACTIVE_HIGH)
> > > > -                     hsync_pol = 1;
> > > > -             if (flags & V4L2_MBUS_VSYNC_ACTIVE_LOW)
> > > > -                     vsync_pol = 1;
> > > > -
> > > > -             ret = ov5640_write_reg(sensor,
> > > > -                                    OV5640_REG_POLARITY_CTRL00,
> > > > -                                    (pclk_pol << 5) |
> > > > -                                    (hsync_pol << 1) |
> > > > -                                    vsync_pol);
> > > > -
> > > > -             if (ret)
> > > > -                     return ret;
> > > > -     }
> > > > -
> > > > -     /*
> > > > -      * powerdown MIPI TX/RX PHY & disable MIPI
> > > > -      *
> > > > -      * MIPI CONTROL 00
> > > > -      * 4:    PWDN PHY TX
> > > > -      * 3:    PWDN PHY RX
> > > > -      * 2:    MIPI enable
> > > > -      */
> > > > -     ret = ov5640_write_reg(sensor,
> > > > -                            OV5640_REG_IO_MIPI_CTRL00, on ? 0x18 : 0);
> > > > -     if (ret)
> > > > -             return ret;
> > > > -
> > > > -     /*
> > > > -      * enable VSYNC/HREF/PCLK DVP control lines
> > > > -      * & D[9:6] DVP data lines
> > > > -      *
> > > > -      * PAD OUTPUT ENABLE 01
> > > > -      * - 6:         VSYNC output enable
> > > > -      * - 5:         HREF output enable
> > > > -      * - 4:         PCLK output enable
> > > > -      * - [3:0]:     D[9:6] output enable
> > > > -      */
> > > > -     ret = ov5640_write_reg(sensor,
> > > > -                            OV5640_REG_PAD_OUTPUT_ENABLE01,
> > > > -                            on ? 0x7f : 0);
> > > > -     if (ret)
> > > > -             return ret;
> > > > -
> > > > -     /*
> > > > -      * enable D[5:0] DVP data lines
> > > > -      *
> > > > -      * PAD OUTPUT ENABLE 02
> > > > -      * - [7:2]:     D[5:0] output enable
> > > > -      */
> > > > -     return ov5640_write_reg(sensor,
> > > > -                             OV5640_REG_PAD_OUTPUT_ENABLE02,
> > > > -                             on ? 0xfc : 0);
> > > > +     return ov5640_write_reg(sensor, OV5640_REG_SYS_CTRL0, on ? 0x2 : 0x42);
> > > >  }
> > > >
> > > >  static int ov5640_set_stream_mipi(struct ov5640_dev *sensor, bool on)
> > > > @@ -2003,6 +1914,10 @@ static void ov5640_set_power_off(struct ov5640_dev *sensor)
> > > >
> > > >  static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
> > > >  {
> > > > +     unsigned int flags = sensor->ep.bus.parallel.flags;
> > > > +     u8 pclk_pol = 0;
> > > > +     u8 hsync_pol = 0;
> > > > +     u8 vsync_pol = 0;
> > > >       int ret = 0;
> > > >
> > > >       if (on) {
> > > > @@ -2014,52 +1929,124 @@ static int ov5640_set_power(struct ov5640_dev *sensor, bool on)
> > > >               if (ret)
> > > >                       goto power_off;
> > > >
> > > > -             /* We're done here for DVP bus, while CSI-2 needs setup. */
> > > > -             if (sensor->ep.bus_type != V4L2_MBUS_CSI2_DPHY)
> > > > -                     return 0;
> > > > +             /* CSI-2 setup. */
> > > > +             if (sensor->ep.bus_type == V4L2_MBUS_CSI2_DPHY) {
> > > > +                     /*
> > > > +                      * Power up MIPI HS Tx and LS Rx; 2 data lanes mode
> > > > +                      *
> > > > +                      * 0x300e = 0x40
> > > > +                      * [7:5] = 010  : 2 data lanes mode (see FIXME note in
> > > > +                      *                "ov5640_set_stream_mipi()")
> > > > +                      * [4] = 0      : Power up MIPI HS Tx
> > > > +                      * [3] = 0      : Power up MIPI LS Rx
> > > > +                      * [2] = 0      : MIPI interface disabled
> > > > +                      */
> > > > +                     ret = ov5640_write_reg(sensor, OV5640_REG_IO_MIPI_CTRL00, 0x40);
> > >
> > > Please wrap lines over 80 if it can be reasonably one.
> > >
> > checkpatch doesn't complain about it  (size is increased to 100)?
>
> That's not a reason leave it as-is.
>
OK.

Cheers,
Prabhakar

> --
> Regards,
>
> Sakari Ailus

  reply index

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2020-07-31  9:24 [PATCH 0/2] media: ov5640 feature enhancement and fixes Lad Prabhakar
2020-07-31  9:24 ` [PATCH 1/2] media: i2c: ov5640: Enable data pins on startup for DVP mode Lad Prabhakar
2020-07-31 13:03   ` Sakari Ailus
2020-07-31 13:18     ` Lad, Prabhakar
2020-07-31 15:19       ` Sakari Ailus
2020-07-31 15:23         ` Lad, Prabhakar [this message]
2020-07-31 15:31       ` Laurent Pinchart
2020-08-01  8:51         ` Lad, Prabhakar
2020-07-31 15:27   ` Laurent Pinchart
2020-08-01  8:46     ` Lad, Prabhakar
2020-07-31  9:24 ` [PATCH 2/2] media: i2c: ov5640: Add support for BT656 mode Lad Prabhakar
2020-07-31 15:23   ` Sakari Ailus
2020-07-31 15:28     ` Lad, Prabhakar

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=CA+V-a8srhDcjjHe73UBTxqz8jooNp4nLvaScLY5jFSNtwYkCcg@mail.gmail.com \
    --to=prabhakar.csengg@gmail.com \
    --cc=biju.das.jz@bp.renesas.com \
    --cc=hugues.fruchet@st.com \
    --cc=jacopo@jmondi.org \
    --cc=laurent.pinchart@ideasonboard.com \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-media@vger.kernel.org \
    --cc=linux-renesas-soc@vger.kernel.org \
    --cc=mchehab@kernel.org \
    --cc=prabhakar.mahadev-lad.rj@bp.renesas.com \
    --cc=sakari.ailus@linux.intel.com \
    --cc=slongerbeam@gmail.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link

Linux-Renesas-SoC Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-renesas-soc/0 linux-renesas-soc/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-renesas-soc linux-renesas-soc/ https://lore.kernel.org/linux-renesas-soc \
		linux-renesas-soc@vger.kernel.org
	public-inbox-index linux-renesas-soc

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.kernel.vger.linux-renesas-soc


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git