From: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
To: Chris Brandt <Chris.Brandt@renesas.com>
Cc: "linux-usb@vger.kernel.org" <linux-usb@vger.kernel.org>,
"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
"linux-renesas-soc@vger.kernel.org"
<linux-renesas-soc@vger.kernel.org>,
Chris Brandt <Chris.Brandt@renesas.com>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
Simon Horman <horms@verge.net.au>
Subject: RE: [PATCH 03/10] phy: renesas: rcar-gen3-usb2: Check dr_mode when not using OTG
Date: Thu, 9 May 2019 07:14:02 +0000 [thread overview]
Message-ID: <OSBPR01MB3174708A983E7148D0F2F7CCD8330@OSBPR01MB3174.jpnprd01.prod.outlook.com> (raw)
In-Reply-To: <20190506234631.113226-4-chris.brandt@renesas.com>
Hi Chrisさん
Thank you for the patch!
> From: Chris Brandt, Sent: Tuesday, May 7, 2019 8:46 AM
>
> When not using OTG, the PHY will need to know if it should function as
> host or peripheral by checking dr_mode in the PHY node (not the parent
> controller node).
>
> Signed-off-by: Chris Brandt <chris.brandt@renesas.com>
> ---
> drivers/phy/renesas/phy-rcar-gen3-usb2.c | 8 +++++++-
> 1 file changed, 7 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/phy/renesas/phy-rcar-gen3-usb2.c b/drivers/phy/renesas/phy-rcar-gen3-usb2.c
> index 218b32e458cb..4eaa228ebd30 100644
> --- a/drivers/phy/renesas/phy-rcar-gen3-usb2.c
> +++ b/drivers/phy/renesas/phy-rcar-gen3-usb2.c
> @@ -408,7 +408,12 @@ static int rcar_gen3_phy_usb2_init(struct phy *p)
> if (rcar_gen3_needs_init_otg(channel))
> rcar_gen3_init_otg(channel);
> rphy->otg_initialized = true;
> - }
> + } else
As Sergei-san said, this should be "} else {"
> + /* Not OTG, so dr_mode should be set in PHY node */
> + if (usb_get_dr_mode(channel->dev) == USB_DR_MODE_PERIPHERAL)
> + writel(0x80000000, usb2_base + USB2_COMMCTRL);
> + else
I would like to add "else if usb_get_dr_mode(channel->dev) == USB_DR_MODE_HOST)"
for a PHY node without "dr_mode" property. In other words, if the PHY node
doesn't have dr_mode property like R-Car, this condition can be the same behavior as previous.
> + writel(0x00000000, usb2_base + USB2_COMMCTRL);
>
> rphy->initialized = true;
>
> @@ -638,6 +643,7 @@ static int rcar_gen3_phy_usb2_probe(struct platform_device *pdev)
> if (of_property_read_bool(dev->of_node, "renesas,uses_usb_x1"))
> channel->uses_usb_x1 = true;
>
> +
As Sergei-san said, this is not needed :)
Best regards,
Yoshihiro Shimoda
next prev parent reply other threads:[~2019-05-09 7:14 UTC|newest]
Thread overview: 39+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-05-06 23:46 [PATCH 00/10] usb: Add host and device support for RZ/A2 Chris Brandt
2019-05-06 23:46 ` [PATCH 01/10] phy: renesas: rcar-gen3-usb2: Add uses_usb_x1 option Chris Brandt
2019-05-07 8:01 ` Geert Uytterhoeven
2019-05-07 11:00 ` Chris Brandt
2019-05-07 11:26 ` Geert Uytterhoeven
2019-05-07 15:43 ` Chris Brandt
2019-05-07 16:32 ` Geert Uytterhoeven
2019-05-07 20:27 ` Chris Brandt
2019-05-08 6:59 ` Geert Uytterhoeven
2019-05-06 23:46 ` [PATCH 02/10] dt-bindings: rcar-gen3-phy-usb2: Document uses_usb_x1 Chris Brandt
2019-05-07 1:05 ` Rob Herring
2019-05-07 1:17 ` Chris Brandt
2019-05-07 8:37 ` Sergei Shtylyov
2019-05-06 23:46 ` [PATCH 03/10] phy: renesas: rcar-gen3-usb2: Check dr_mode when not using OTG Chris Brandt
2019-05-07 8:40 ` Sergei Shtylyov
2019-05-07 11:26 ` Sergei Shtylyov
2019-05-07 11:45 ` Chris Brandt
2019-05-07 14:28 ` Sergei Shtylyov
2019-05-07 14:43 ` Chris Brandt
2019-05-09 7:14 ` Yoshihiro Shimoda [this message]
2019-05-06 23:46 ` [PATCH 04/10] dt-bindings: rcar-gen3-phy-usb2: Document dr_mode Chris Brandt
2019-05-06 23:46 ` [PATCH 05/10] dt-bindings: rcar-gen3-phy-usb2: Add r7s9210 support Chris Brandt
2019-05-06 23:46 ` [PATCH 06/10] usb: renesas_usbhs: Add support for RZ/A2 Chris Brandt
2019-05-09 7:04 ` Yoshihiro Shimoda
2019-05-09 14:42 ` Chris Brandt
2019-05-06 23:46 ` [PATCH 07/10] dt-bindings: usb: renesas_usbhs: Add support for r7s9210 Chris Brandt
2019-05-06 23:46 ` [PATCH 08/10] ARM: dts: r7s9210: Add USB Host support Chris Brandt
2019-05-08 9:44 ` Simon Horman
2019-05-06 23:46 ` [PATCH 09/10] ARM: dts: r7s9210: Add USB Device support Chris Brandt
2019-05-07 8:44 ` Sergei Shtylyov
2019-05-07 11:05 ` Chris Brandt
2019-05-08 9:43 ` Simon Horman
2019-05-08 9:45 ` Simon Horman
2019-05-06 23:46 ` [PATCH 10/10] ARM: dts: r7s9210-rza2mevb: Add USB host support Chris Brandt
2019-05-08 9:42 ` Simon Horman
2019-05-08 12:48 ` Chris Brandt
2019-05-07 9:17 ` [PATCH 00/10] usb: Add host and device support for RZ/A2 Yoshihiro Shimoda
2019-05-08 18:07 ` Chris Brandt
2019-05-09 6:23 ` Yoshihiro Shimoda
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=OSBPR01MB3174708A983E7148D0F2F7CCD8330@OSBPR01MB3174.jpnprd01.prod.outlook.com \
--to=yoshihiro.shimoda.uh@renesas.com \
--cc=Chris.Brandt@renesas.com \
--cc=devicetree@vger.kernel.org \
--cc=gregkh@linuxfoundation.org \
--cc=horms@verge.net.au \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=linux-usb@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).