From: Chris Brandt <Chris.Brandt@renesas.com>
To: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Mark Brown <broonie@kernel.org>, Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Geert Uytterhoeven <geert+renesas@glider.be>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
linux-spi <linux-spi@vger.kernel.org>,
"open list:OPEN FIRMWARE AND FLATTENED DEVICE TREE BINDINGS"
<devicetree@vger.kernel.org>,
Linux-Renesas <linux-renesas-soc@vger.kernel.org>,
linux-clk <linux-clk@vger.kernel.org>,
Mason Yang <masonccyang@mxic.com.tw>,
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Subject: RE: [PATCH 6/6] dt-bindings: spi: Document Renesas SPIBSC bindings
Date: Thu, 5 Dec 2019 16:00:45 +0000 [thread overview]
Message-ID: <TY1PR01MB1562F5908AC7A9643F51FEBE8A5C0@TY1PR01MB1562.jpnprd01.prod.outlook.com> (raw)
In-Reply-To: <CAMuHMdVy_0e5_94a-G83Tt14XsxmLFOpstvSP6Yw8m9oRW_eZg@mail.gmail.com>
Hi Geert,
On Thu, Dec 5, 2019 1, Geert Uytterhoeven wrote:
> Your spibsc driver does:
>
> master->mode_bits = SPI_CPOL | SPI_CPHA;
>
> i.e. SPI_[TR]X_{QUAD,DUAL} are not set, so it should not try those modes.
OK, Thank you!
> At least on RSK+RZA1, the FLASHes are wired in quad mode, so you should
> describe the hardware in DT.
OK.
> > > BTW, when using spibsc in direct-mapped mode: if you turn of and on
> > > again the module clock, does the spibsc need reprogramming?
> >
> > Nope. Everything will stay the same (just like all the other peripherals).
> The only thing you 'might' want to do is flush the read cache (especially if
> you disconnected it because you were going to go out and re-write some of the
> flash in SPI mode).
>
> Good. So that means the MTD driver can be modular. Unused clocks are turned
> off at boot, and can be turned on when the mtd-rom driver is loaded and
> activated.
I'm going to do some testing now and then send out a V2 to see if we are
getting closer to a consensus.
Chris
next prev parent reply other threads:[~2019-12-05 16:01 UTC|newest]
Thread overview: 50+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-12-03 3:45 [PATCH 0/6] spi: Add Renesas SPIBSC controller Chris Brandt
2019-12-03 3:45 ` [PATCH 1/6] clk: renesas: mstp: Add critical clock from device tree support Chris Brandt
2019-12-03 18:32 ` Geert Uytterhoeven
2019-12-03 18:46 ` Chris Brandt
2019-12-03 18:51 ` Geert Uytterhoeven
2019-12-03 3:45 ` [PATCH 2/6] ARM: dts: r7s72100: Add SPIBSC clocks Chris Brandt
2019-12-03 18:42 ` Geert Uytterhoeven
2019-12-03 18:57 ` Chris Brandt
2019-12-03 19:12 ` Geert Uytterhoeven
2019-12-04 8:38 ` Lee Jones
2019-12-04 9:03 ` Geert Uytterhoeven
2019-12-04 9:47 ` Lee Jones
2019-12-04 11:00 ` Chris Brandt
2019-12-03 3:45 ` [PATCH 3/6] clk: renesas: r7s9210: Add SPIBSC clock Chris Brandt
2019-12-03 18:49 ` Geert Uytterhoeven
2019-12-03 19:09 ` Chris Brandt
2019-12-03 20:40 ` Geert Uytterhoeven
2019-12-04 3:09 ` Chris Brandt
2019-12-03 3:45 ` [PATCH 4/6] spi: Add SPIBSC driver Chris Brandt
2019-12-03 14:19 ` Mark Brown
2019-12-03 15:00 ` Chris Brandt
2019-12-03 18:29 ` Geert Uytterhoeven
2019-12-04 11:25 ` Mark Brown
2019-12-04 12:14 ` Geert Uytterhoeven
2019-12-04 15:51 ` Chris Brandt
2019-12-04 16:49 ` Mark Brown
2019-12-03 18:28 ` Geert Uytterhoeven
2019-12-04 11:18 ` Mark Brown
2019-12-04 22:12 ` Chris Brandt
2019-12-03 3:45 ` [PATCH 5/6] ARM: dts: r7s9210: Add SPIBSC Device support Chris Brandt
2019-12-03 18:59 ` Geert Uytterhoeven
2019-12-03 22:38 ` Chris Brandt
2019-12-04 7:57 ` Geert Uytterhoeven
2019-12-04 11:04 ` Chris Brandt
2019-12-03 3:45 ` [PATCH 6/6] dt-bindings: spi: Document Renesas SPIBSC bindings Chris Brandt
2019-12-03 9:14 ` Sergei Shtylyov
2019-12-03 13:27 ` Chris Brandt
2019-12-03 16:04 ` Sergei Shtylyov
2019-12-03 16:35 ` Chris Brandt
2019-12-03 18:57 ` Geert Uytterhoeven
2019-12-03 20:39 ` Geert Uytterhoeven
2019-12-04 2:54 ` Chris Brandt
2019-12-04 8:56 ` Geert Uytterhoeven
2019-12-04 13:31 ` Chris Brandt
2019-12-05 15:48 ` Geert Uytterhoeven
2019-12-05 16:00 ` Chris Brandt [this message]
2019-12-04 8:40 ` Geert Uytterhoeven
2019-12-03 22:33 ` Chris Brandt
2019-12-04 8:43 ` Geert Uytterhoeven
2019-12-04 11:19 ` Chris Brandt
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=TY1PR01MB1562F5908AC7A9643F51FEBE8A5C0@TY1PR01MB1562.jpnprd01.prod.outlook.com \
--to=chris.brandt@renesas.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=geert+renesas@glider.be \
--cc=geert@linux-m68k.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-renesas-soc@vger.kernel.org \
--cc=linux-spi@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=masonccyang@mxic.com.tw \
--cc=mturquette@baylibre.com \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
--cc=sergei.shtylyov@cogentembedded.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).