Linux-RISC-V Archive on lore.kernel.org
 help / color / Atom feed
* [RFT PATCH] riscv: mremap speedup - enable HAVE_MOVE_PUD and HAVE_MOVE_PMD
@ 2021-04-16 16:37 Jisheng Zhang
  0 siblings, 0 replies; only message in thread
From: Jisheng Zhang @ 2021-04-16 16:37 UTC (permalink / raw)
  To: Paul Walmsley, Palmer Dabbelt, Albert Ou; +Cc: linux-riscv, linux-kernel

From: Jisheng Zhang <jszhang@kernel.org>

HAVE_MOVE_PUD enables remapping pages at the PUD level if both the source
and destination addresses are PUD-aligned.
HAVE_MOVE_PMD does similar speedup on the PMD level.

With HAVE_MOVE_PUD enabled, there is about a 143x improvement on qemu
With HAVE_MOVE_PMD enabled, there is about a 5x improvement on qemu

Signed-off-by: Jisheng Zhang <jszhang@kernel.org>
---
Hi all,

After reading the risc-v privileged spec, I think it's safe to support
the HAVE_MOVE_PUD and HAVE_MOVE_PMD optimization on riscv. The patch passed
the mremap_test on QEMU. However this can't be tested on real HW due to lack
of HW boards, this is the reason why I mark this patch as RFT. I hope I can
buy a sipeed Allwiner D1 SoC powered SBC soon, at least I can test
HAVE_MOVE_PMD. Helping me to test on real HW is appreciated!

Thanks

 arch/riscv/Kconfig               |  2 ++
 arch/riscv/include/asm/pgtable.h | 12 ++++++++++++
 2 files changed, 14 insertions(+)

diff --git a/arch/riscv/Kconfig b/arch/riscv/Kconfig
index e8074d248457..37660de68b00 100644
--- a/arch/riscv/Kconfig
+++ b/arch/riscv/Kconfig
@@ -80,6 +80,8 @@ config RISCV
 	select HAVE_KPROBES
 	select HAVE_KPROBES_ON_FTRACE
 	select HAVE_KRETPROBES
+	select HAVE_MOVE_PMD
+	select HAVE_MOVE_PUD
 	select HAVE_PCI
 	select HAVE_PERF_EVENTS
 	select HAVE_PERF_REGS
diff --git a/arch/riscv/include/asm/pgtable.h b/arch/riscv/include/asm/pgtable.h
index ebf817c1bdf4..287733b95d10 100644
--- a/arch/riscv/include/asm/pgtable.h
+++ b/arch/riscv/include/asm/pgtable.h
@@ -360,6 +360,18 @@ static inline void set_pte_at(struct mm_struct *mm,
 	set_pte(ptep, pteval);
 }
 
+static inline void set_pmd_at(struct mm_struct *mm, unsigned long addr,
+			      pmd_t *pmdp, pmd_t pmd)
+{
+	set_pmd(pmdp, pmd);
+}
+
+static inline void set_pud_at(struct mm_struct *mm, unsigned long addr,
+			      pud_t *pudp, pud_t pud)
+{
+	set_pud(pudp, pud);
+}
+
 static inline void pte_clear(struct mm_struct *mm,
 	unsigned long addr, pte_t *ptep)
 {
-- 
2.31.0



_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] only message in thread

only message in thread, back to index

Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-04-16 16:37 [RFT PATCH] riscv: mremap speedup - enable HAVE_MOVE_PUD and HAVE_MOVE_PMD Jisheng Zhang

Linux-RISC-V Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-riscv/0 linux-riscv/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-riscv linux-riscv/ https://lore.kernel.org/linux-riscv \
		linux-riscv@lists.infradead.org
	public-inbox-index linux-riscv

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-riscv


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git