Linux-RISC-V Archive on lore.kernel.org
 help / color / Atom feed
* [PATCH v4 0/5] Add Microchip PolarFire Soc Support
@ 2021-03-03 20:02 Atish Patra
  2021-03-03 20:02 ` [PATCH v4 1/5] RISC-V: Add Microchip PolarFire SoC kconfig option Atish Patra
                   ` (5 more replies)
  0 siblings, 6 replies; 21+ messages in thread
From: Atish Patra @ 2021-03-03 20:02 UTC (permalink / raw)
  To: linux-kernel
  Cc: Atish Patra, Albert Ou, Alistair Francis, Anup Patel,
	Björn Töpel, devicetree, linux-riscv, Palmer Dabbelt,
	Paul Walmsley, Rob Herring, Conor.Dooley, Daire McNamara,
	Ivan.Griffin, Lewis.Hanly

This series adds minimal support for Microchip Polar Fire Soc Icicle kit.
It is rebased on v5.12-rc1 and depends on clock support. 
Only MMC and ethernet drivers are enabled via this series.
The idea here is to add the foundational patches so that other drivers
can be added to on top of this. The device tree may change based on
feedback on bindings of individual driver support patches.

This series has been tested on Qemu and Polar Fire Soc Icicle kit.
It depends on the updated clock-series[2] and macb fix[3].
The series is also tested by Lewis from Microchip.

The series can also be found at.
https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4

[1] https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
[2] https://www.spinics.net/lists/linux-clk/msg54579.html 

Changes from v3->v4:
1. Fixed few DT specific issues.
2. Rebased on top of new clock driver.
3. SD card functionality is verified.

Changes from v2->v3:
1. Fixed a typo in dt binding.
2. Included MAINTAINERS entry for PolarFire SoC.
3. Improved the dts file by using lowercase clock names and keeping phy
   details in board specific dts file.

Changes from v1->v2:
1. Modified the DT to match the device tree in U-Boot.
2. Added both eMMC & SDcard entries in DT. However, SD card is only enabled
   as it allows larger storage option for linux distros.

Atish Patra (4):
RISC-V: Add Microchip PolarFire SoC kconfig option
dt-bindings: riscv: microchip: Add YAML documentation for the
PolarFire SoC
RISC-V: Initial DTS for Microchip ICICLE board
RISC-V: Enable Microchip PolarFire ICICLE SoC

Conor Dooley (1):
MAINTAINERS: add microchip polarfire soc support

.../devicetree/bindings/riscv/microchip.yaml  |  27 ++
MAINTAINERS                                   |   8 +
arch/riscv/Kconfig.socs                       |   7 +
arch/riscv/boot/dts/Makefile                  |   1 +
arch/riscv/boot/dts/microchip/Makefile        |   2 +
.../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
.../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
arch/riscv/configs/defconfig                  |   4 +
8 files changed, 450 insertions(+)
create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml
create mode 100644 arch/riscv/boot/dts/microchip/Makefile
create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi

--
2.25.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH v4 1/5] RISC-V: Add Microchip PolarFire SoC kconfig option
  2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
@ 2021-03-03 20:02 ` Atish Patra
  2021-03-03 20:02 ` [PATCH v4 2/5] dt-bindings: riscv: microchip: Add YAML documentation for the PolarFire SoC Atish Patra
                   ` (4 subsequent siblings)
  5 siblings, 0 replies; 21+ messages in thread
From: Atish Patra @ 2021-03-03 20:02 UTC (permalink / raw)
  To: linux-kernel
  Cc: Atish Patra, Bin Meng, Anup Patel, Albert Ou, Alistair Francis,
	Anup Patel, Björn Töpel, devicetree, linux-riscv,
	Palmer Dabbelt, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

Add Microchip PolarFire kconfig option which selects SoC specific
and common drivers that is required for this SoC.

Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
---
 arch/riscv/Kconfig.socs | 7 +++++++
 1 file changed, 7 insertions(+)

diff --git a/arch/riscv/Kconfig.socs b/arch/riscv/Kconfig.socs
index 7efcece8896c..82b298bfd3be 100644
--- a/arch/riscv/Kconfig.socs
+++ b/arch/riscv/Kconfig.socs
@@ -1,5 +1,12 @@
 menu "SoC selection"
 
+config SOC_MICROCHIP_POLARFIRE
+	bool "Microchip PolarFire SoCs"
+	select MCHP_CLK_MPFS
+	select SIFIVE_PLIC
+	help
+	  This enables support for Microchip PolarFire SoC platforms.
+
 config SOC_SIFIVE
 	bool "SiFive SoCs"
 	select SERIAL_SIFIVE if TTY
-- 
2.25.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH v4 2/5] dt-bindings: riscv: microchip: Add YAML documentation for the PolarFire SoC
  2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
  2021-03-03 20:02 ` [PATCH v4 1/5] RISC-V: Add Microchip PolarFire SoC kconfig option Atish Patra
@ 2021-03-03 20:02 ` Atish Patra
  2021-03-08 20:11   ` Rob Herring
  2021-03-03 20:02 ` [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
                   ` (3 subsequent siblings)
  5 siblings, 1 reply; 21+ messages in thread
From: Atish Patra @ 2021-03-03 20:02 UTC (permalink / raw)
  To: linux-kernel
  Cc: Atish Patra, Albert Ou, Alistair Francis, Anup Patel,
	Björn Töpel, devicetree, linux-riscv, Palmer Dabbelt,
	Paul Walmsley, Rob Herring, Conor.Dooley, Daire McNamara,
	Ivan.Griffin, Lewis.Hanly

Add YAML DT binding documentation for the Microchip PolarFire SoC.
It is documented at:

https://www.microsemi.com/products/fpga-soc/polarfire-soc-icicle-quick-start-guide

Signed-off-by: Atish Patra <atish.patra@wdc.com>
---
 .../devicetree/bindings/riscv/microchip.yaml  | 27 +++++++++++++++++++
 1 file changed, 27 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml

diff --git a/Documentation/devicetree/bindings/riscv/microchip.yaml b/Documentation/devicetree/bindings/riscv/microchip.yaml
new file mode 100644
index 000000000000..3f981e897126
--- /dev/null
+++ b/Documentation/devicetree/bindings/riscv/microchip.yaml
@@ -0,0 +1,27 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/riscv/microchip.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Microchip PolarFire SoC-based boards device tree bindings
+
+maintainers:
+  - Cyril Jean <Cyril.Jean@microchip.com>
+  - Lewis Hanly <lewis.hanly@microchip.com>
+
+description:
+  Microchip PolarFire SoC-based boards
+
+properties:
+  $nodename:
+    const: '/'
+  compatible:
+    items:
+      - enum:
+          - microchip,mpfs-icicle-kit
+      - const: microchip,mpfs
+
+additionalProperties: true
+
+...
-- 
2.25.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
  2021-03-03 20:02 ` [PATCH v4 1/5] RISC-V: Add Microchip PolarFire SoC kconfig option Atish Patra
  2021-03-03 20:02 ` [PATCH v4 2/5] dt-bindings: riscv: microchip: Add YAML documentation for the PolarFire SoC Atish Patra
@ 2021-03-03 20:02 ` Atish Patra
  2021-03-09 10:56   ` Ben Dooks
                     ` (2 more replies)
  2021-03-03 20:02 ` [PATCH v4 4/5] RISC-V: Enable Microchip PolarFire ICICLE SoC Atish Patra
                   ` (2 subsequent siblings)
  5 siblings, 3 replies; 21+ messages in thread
From: Atish Patra @ 2021-03-03 20:02 UTC (permalink / raw)
  To: linux-kernel
  Cc: Atish Patra, Albert Ou, Alistair Francis, Anup Patel,
	Björn Töpel, devicetree, linux-riscv, Palmer Dabbelt,
	Paul Walmsley, Rob Herring, Conor.Dooley, Daire McNamara,
	Ivan.Griffin, Lewis.Hanly

Add initial DTS for Microchip ICICLE board having only
essential devices (clocks, sdhci, ethernet, serial, etc).
The device tree is based on the U-Boot patch.

https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/

Signed-off-by: Atish Patra <atish.patra@wdc.com>
---
 arch/riscv/boot/dts/Makefile                  |   1 +
 arch/riscv/boot/dts/microchip/Makefile        |   2 +
 .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
 .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
 4 files changed, 404 insertions(+)
 create mode 100644 arch/riscv/boot/dts/microchip/Makefile
 create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
 create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi

diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
index 7ffd502e3e7b..fe996b88319e 100644
--- a/arch/riscv/boot/dts/Makefile
+++ b/arch/riscv/boot/dts/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 subdir-y += sifive
 subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
+subdir-y += microchip
 
 obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
new file mode 100644
index 000000000000..622b12771fd3
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
new file mode 100644
index 000000000000..ec79944065c9
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
@@ -0,0 +1,72 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2020 Microchip Technology Inc */
+
+/dts-v1/;
+
+#include "microchip-mpfs.dtsi"
+
+/* Clock frequency (in Hz) of the rtcclk */
+#define RTCCLK_FREQ		1000000
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "Microchip PolarFire-SoC Icicle Kit";
+	compatible = "microchip,mpfs-icicle-kit";
+
+	chosen {
+		stdout-path = &serial0;
+	};
+
+	cpus {
+		timebase-frequency = <RTCCLK_FREQ>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x0 0x40000000>;
+		clocks = <&clkcfg 26>;
+	};
+
+	soc {
+	};
+};
+
+&serial0 {
+	status = "okay";
+};
+
+&serial1 {
+	status = "okay";
+};
+
+&serial2 {
+	status = "okay";
+};
+
+&serial3 {
+	status = "okay";
+};
+
+&sdcard {
+	status = "okay";
+};
+
+&emac0 {
+	phy-mode = "sgmii";
+	phy-handle = <&phy0>;
+	phy0: ethernet-phy@8 {
+		reg = <8>;
+		ti,fifo-depth = <0x01>;
+	};
+};
+
+&emac1 {
+	status = "okay";
+	phy-mode = "sgmii";
+	phy-handle = <&phy1>;
+	phy1: ethernet-phy@9 {
+		reg = <9>;
+		ti,fifo-depth = <0x01>;
+	};
+};
diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
new file mode 100644
index 000000000000..b9819570a7d1
--- /dev/null
+++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
@@ -0,0 +1,329 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (c) 2020 Microchip Technology Inc */
+
+/dts-v1/;
+
+/ {
+	#address-cells = <2>;
+	#size-cells = <2>;
+	model = "Microchip MPFS Icicle Kit";
+	compatible = "microchip,mpfs-icicle-kit";
+
+	chosen {
+	};
+
+	cpus {
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		cpu@0 {
+			clock-frequency = <0>;
+			compatible = "sifive,e51", "sifive,rocket0", "riscv";
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <128>;
+			i-cache-size = <16384>;
+			reg = <0>;
+			riscv,isa = "rv64imac";
+			status = "disabled";
+
+			cpu0_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+
+		cpu@1 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <1>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			status = "okay";
+
+			cpu1_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+
+		cpu@2 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <2>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			status = "okay";
+
+			cpu2_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+
+		cpu@3 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <3>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			status = "okay";
+
+			cpu3_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+
+		cpu@4 {
+			clock-frequency = <0>;
+			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
+			d-cache-block-size = <64>;
+			d-cache-sets = <64>;
+			d-cache-size = <32768>;
+			d-tlb-sets = <1>;
+			d-tlb-size = <32>;
+			device_type = "cpu";
+			i-cache-block-size = <64>;
+			i-cache-sets = <64>;
+			i-cache-size = <32768>;
+			i-tlb-sets = <1>;
+			i-tlb-size = <32>;
+			mmu-type = "riscv,sv39";
+			reg = <4>;
+			riscv,isa = "rv64imafdc";
+			tlb-split;
+			status = "okay";
+			cpu4_intc: interrupt-controller {
+				#interrupt-cells = <1>;
+				compatible = "riscv,cpu-intc";
+				interrupt-controller;
+			};
+		};
+	};
+
+	soc {
+		#address-cells = <2>;
+		#size-cells = <2>;
+		compatible = "simple-bus";
+		ranges;
+
+		cache-controller@2010000 {
+			compatible = "sifive,fu540-c000-ccache", "cache";
+			cache-block-size = <64>;
+			cache-level = <2>;
+			cache-sets = <1024>;
+			cache-size = <2097152>;
+			cache-unified;
+			interrupt-parent = <&plic>;
+			interrupts = <1 2 3>;
+			reg = <0x0 0x2010000 0x0 0x1000>;
+		};
+
+		clint@2000000 {
+			compatible = "sifive,clint0";
+			reg = <0x0 0x2000000 0x0 0xC000>;
+			interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
+						&cpu1_intc 3 &cpu1_intc 7
+						&cpu2_intc 3 &cpu2_intc 7
+						&cpu3_intc 3 &cpu3_intc 7
+						&cpu4_intc 3 &cpu4_intc 7>;
+		};
+
+		plic: interrupt-controller@c000000 {
+			#interrupt-cells = <1>;
+			compatible = "sifive,plic-1.0.0";
+			reg = <0x0 0xc000000 0x0 0x4000000>;
+			riscv,ndev = <186>;
+			interrupt-controller;
+			interrupts-extended = <&cpu0_intc 11
+					&cpu1_intc 11 &cpu1_intc 9
+					&cpu2_intc 11 &cpu2_intc 9
+					&cpu3_intc 11 &cpu3_intc 9
+					&cpu4_intc 11 &cpu4_intc 9>;
+		};
+
+		dma@3000000 {
+			compatible = "sifive,fu540-c000-pdma";
+			reg = <0x0 0x3000000 0x0 0x8000>;
+			interrupt-parent = <&plic>;
+			interrupts = <23 24 25 26 27 28 29 30>;
+			#dma-cells = <1>;
+		};
+
+		refclk: refclk {
+			compatible = "fixed-clock";
+			#clock-cells = <0>;
+			clock-frequency = <600000000>;
+			clock-output-names = "msspllclk";
+		};
+
+		clkcfg: clkcfg@20002000 {
+			compatible = "microchip,mpfs-clkcfg";
+			reg = <0x0 0x20002000 0x0 0x1000>;
+			reg-names = "mss_sysreg";
+			clocks = <&refclk>;
+			#clock-cells = <1>;
+			clock-output-names = "cpu", "axi", "ahb", "envm",	/* 0-3   */
+				 "mac0", "mac1", "mmc", "timer",		/* 4-7   */
+				"mmuart0", "mmuart1", "mmuart2", "mmuart3",	/* 8-11  */
+				"mmuart4", "spi0", "spi1", "i2c0",		/* 12-15 */
+				"i2c1", "can0", "can1", "usb",			/* 16-19 */
+				"rsvd", "rtc", "qspi", "gpio0",			/* 20-23 */
+				"gpio1", "gpio2", "ddrc", "fic0",		/* 24-27 */
+				"fic1", "fic2", "fic3", "athena", "cfm";	/* 28-32 */
+		};
+
+		serial0: serial@20000000 {
+			compatible = "ns16550a";
+			reg = <0x0 0x20000000 0x0 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupt-parent = <&plic>;
+			interrupts = <90>;
+			current-speed = <115200>;
+			clocks = <&clkcfg 8>;
+			status = "disabled";
+		};
+
+		serial1: serial@20100000 {
+			compatible = "ns16550a";
+			reg = <0x0 0x20100000 0x0 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupt-parent = <&plic>;
+			interrupts = <91>;
+			current-speed = <115200>;
+			clocks = <&clkcfg 9>;
+			status = "disabled";
+		};
+
+		serial2: serial@20102000 {
+			compatible = "ns16550a";
+			reg = <0x0 0x20102000 0x0 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupt-parent = <&plic>;
+			interrupts = <92>;
+			current-speed = <115200>;
+			clocks = <&clkcfg 10>;
+			status = "disabled";
+		};
+
+		serial3: serial@20104000 {
+			compatible = "ns16550a";
+			reg = <0x0 0x20104000 0x0 0x400>;
+			reg-io-width = <4>;
+			reg-shift = <2>;
+			interrupt-parent = <&plic>;
+			interrupts = <93>;
+			current-speed = <115200>;
+			clocks = <&clkcfg 11>;
+			status = "disabled";
+		};
+
+		emmc: mmc@20008000 {
+			compatible = "cdns,sd4hc";
+			reg = <0x0 0x20008000 0x0 0x1000>;
+			interrupt-parent = <&plic>;
+			interrupts = <88 89>;
+			pinctrl-names = "default";
+			clocks = <&clkcfg 6>;
+			bus-width = <4>;
+			cap-mmc-highspeed;
+			mmc-ddr-3_3v;
+			max-frequency = <200000000>;
+			non-removable;
+			no-sd;
+			no-sdio;
+			voltage-ranges = <3300 3300>;
+			status = "disabled";
+		};
+
+		sdcard: sdhc@20008000 {
+			compatible = "cdns,sd4hc";
+			reg = <0x0 0x20008000 0x0 0x1000>;
+			interrupt-parent = <&plic>;
+			interrupts = <88>;
+			pinctrl-names = "default";
+			clocks = <&clkcfg 6>;
+			bus-width = <4>;
+			disable-wp;
+			cap-sd-highspeed;
+			card-detect-delay = <200>;
+			sd-uhs-sdr12;
+			sd-uhs-sdr25;
+			sd-uhs-sdr50;
+			sd-uhs-sdr104;
+			max-frequency = <200000000>;
+			status = "disabled";
+		};
+
+		emac0: ethernet@20110000 {
+			compatible = "cdns,macb";
+			reg = <0x0 0x20110000 0x0 0x2000>;
+			interrupt-parent = <&plic>;
+			interrupts = <64 65 66 67>;
+			local-mac-address = [00 00 00 00 00 00];
+			clocks = <&clkcfg 4>, <&clkcfg 2>;
+			clock-names = "pclk", "hclk";
+			status = "disabled";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+		emac1: ethernet@20112000 {
+			compatible = "cdns,macb";
+			reg = <0x0 0x20112000 0x0 0x2000>;
+			interrupt-parent = <&plic>;
+			interrupts = <70 71 72 73>;
+			mac-address = [00 00 00 00 00 00];
+			clocks = <&clkcfg 5>, <&clkcfg 2>;
+			status = "disabled";
+			clock-names = "pclk", "hclk";
+			#address-cells = <1>;
+			#size-cells = <0>;
+		};
+
+	};
+};
-- 
2.25.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH v4 4/5] RISC-V: Enable Microchip PolarFire ICICLE SoC
  2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
                   ` (2 preceding siblings ...)
  2021-03-03 20:02 ` [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
@ 2021-03-03 20:02 ` Atish Patra
  2021-03-03 20:02 ` [PATCH v4 5/5] MAINTAINERS: add microchip polarfire soc support Atish Patra
  2021-03-30  4:17 ` [PATCH v4 0/5] Add Microchip PolarFire Soc Support Palmer Dabbelt
  5 siblings, 0 replies; 21+ messages in thread
From: Atish Patra @ 2021-03-03 20:02 UTC (permalink / raw)
  To: linux-kernel
  Cc: Atish Patra, Anup Patel, Bin Meng, Albert Ou, Alistair Francis,
	Anup Patel, Björn Töpel, devicetree, linux-riscv,
	Palmer Dabbelt, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

Enable Microchip PolarFire ICICLE soc config in defconfig.
It allows the default upstream kernel to boot on PolarFire ICICLE board.

Signed-off-by: Atish Patra <atish.patra@wdc.com>
Reviewed-by: Anup Patel <anup@brainfault.org>
Reviewed-by: Bin Meng <bin.meng@windriver.com>
---
 arch/riscv/configs/defconfig | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/riscv/configs/defconfig b/arch/riscv/configs/defconfig
index 6c0625aa96c7..1f2be234b11c 100644
--- a/arch/riscv/configs/defconfig
+++ b/arch/riscv/configs/defconfig
@@ -16,6 +16,7 @@ CONFIG_EXPERT=y
 CONFIG_BPF_SYSCALL=y
 CONFIG_SOC_SIFIVE=y
 CONFIG_SOC_VIRT=y
+CONFIG_SOC_MICROCHIP_POLARFIRE=y
 CONFIG_SMP=y
 CONFIG_HOTPLUG_CPU=y
 CONFIG_JUMP_LABEL=y
@@ -82,6 +83,9 @@ CONFIG_USB_OHCI_HCD=y
 CONFIG_USB_OHCI_HCD_PLATFORM=y
 CONFIG_USB_STORAGE=y
 CONFIG_USB_UAS=y
+CONFIG_MMC_SDHCI=y
+CONFIG_MMC_SDHCI_PLTFM=y
+CONFIG_MMC_SDHCI_CADENCE=y
 CONFIG_MMC=y
 CONFIG_MMC_SPI=y
 CONFIG_RTC_CLASS=y
-- 
2.25.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* [PATCH v4 5/5] MAINTAINERS: add microchip polarfire soc support
  2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
                   ` (3 preceding siblings ...)
  2021-03-03 20:02 ` [PATCH v4 4/5] RISC-V: Enable Microchip PolarFire ICICLE SoC Atish Patra
@ 2021-03-03 20:02 ` Atish Patra
  2021-03-30  4:17 ` [PATCH v4 0/5] Add Microchip PolarFire Soc Support Palmer Dabbelt
  5 siblings, 0 replies; 21+ messages in thread
From: Atish Patra @ 2021-03-03 20:02 UTC (permalink / raw)
  To: linux-kernel
  Cc: Conor Dooley, Albert Ou, Alistair Francis, Anup Patel,
	Atish Patra, Björn Töpel, devicetree, linux-riscv,
	Palmer Dabbelt, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

From: Conor Dooley <conor.dooley@microchip.com>

Add Cyril Jean and Lewis Hanly as maintainers for the Microchip SoC
directory

Signed-off-by: Conor Dooley <conor.dooley@microchip.com>
---
 MAINTAINERS | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index d92f85ca831d..cf186eca1784 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -15358,6 +15358,14 @@ F:	arch/riscv/
 N:	riscv
 K:	riscv
 
+RISC-V/MICROCHIP POLARFIRE SOC SUPPORT
+M:	Lewis Hanly <lewis.hanly@microchip.com>
+M:	Cyril Jean <cyril.jean@microchip.com>
+L:	linux-riscv@lists.infradead.org
+S:	Supported
+F:	drivers/soc/microchip/
+F:	include/soc/microchip/mpfs.h
+
 RNBD BLOCK DRIVERS
 M:	Danil Kipnis <danil.kipnis@cloud.ionos.com>
 M:	Jack Wang <jinpu.wang@cloud.ionos.com>
-- 
2.25.1


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 2/5] dt-bindings: riscv: microchip: Add YAML documentation for the PolarFire SoC
  2021-03-03 20:02 ` [PATCH v4 2/5] dt-bindings: riscv: microchip: Add YAML documentation for the PolarFire SoC Atish Patra
@ 2021-03-08 20:11   ` Rob Herring
  0 siblings, 0 replies; 21+ messages in thread
From: Rob Herring @ 2021-03-08 20:11 UTC (permalink / raw)
  To: Atish Patra
  Cc: Ivan.Griffin, Anup Patel, Alistair Francis, linux-riscv,
	Albert Ou, Palmer Dabbelt, devicetree, Björn Töpel,
	Daire McNamara, Paul Walmsley, Conor.Dooley, linux-kernel,
	Lewis.Hanly, Rob Herring

On Wed, 03 Mar 2021 12:02:50 -0800, Atish Patra wrote:
> Add YAML DT binding documentation for the Microchip PolarFire SoC.
> It is documented at:
> 
> https://www.microsemi.com/products/fpga-soc/polarfire-soc-icicle-quick-start-guide
> 
> Signed-off-by: Atish Patra <atish.patra@wdc.com>
> ---
>  .../devicetree/bindings/riscv/microchip.yaml  | 27 +++++++++++++++++++
>  1 file changed, 27 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml
> 

Reviewed-by: Rob Herring <robh@kernel.org>

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-03-03 20:02 ` [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
@ 2021-03-09 10:56   ` Ben Dooks
       [not found]     ` <DM6PR11MB3770E7FA8121AA91D9EDC4FEE5929@DM6PR11MB3770.namprd11.prod.outlook.com>
  2021-03-22  6:04   ` Bin Meng
  2021-03-27 17:22   ` Alex Ghiti
  2 siblings, 1 reply; 21+ messages in thread
From: Ben Dooks @ 2021-03-09 10:56 UTC (permalink / raw)
  To: Atish Patra, linux-kernel
  Cc: Albert Ou, Alistair Francis, Anup Patel, Björn Töpel,
	devicetree, linux-riscv, Palmer Dabbelt, Paul Walmsley,
	Rob Herring, Conor.Dooley, Daire McNamara, Ivan.Griffin,
	Lewis.Hanly

On 03/03/2021 20:02, Atish Patra wrote:
> Add initial DTS for Microchip ICICLE board having only
> essential devices (clocks, sdhci, ethernet, serial, etc).
> The device tree is based on the U-Boot patch.
> 
> https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> 
> Signed-off-by: Atish Patra <atish.patra@wdc.com>
> ---
>   arch/riscv/boot/dts/Makefile                  |   1 +
>   arch/riscv/boot/dts/microchip/Makefile        |   2 +
>   .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
>   .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
>   4 files changed, 404 insertions(+)
>   create mode 100644 arch/riscv/boot/dts/microchip/Makefile
>   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
>   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> 
> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> index 7ffd502e3e7b..fe996b88319e 100644
> --- a/arch/riscv/boot/dts/Makefile
> +++ b/arch/riscv/boot/dts/Makefile
> @@ -1,5 +1,6 @@
>   # SPDX-License-Identifier: GPL-2.0
>   subdir-y += sifive
>   subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> +subdir-y += microchip
>   
>   obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> new file mode 100644
> index 000000000000..622b12771fd3
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> new file mode 100644
> index 000000000000..ec79944065c9
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/* Copyright (c) 2020 Microchip Technology Inc */
> +
> +/dts-v1/;
> +
> +#include "microchip-mpfs.dtsi"
> +
> +/* Clock frequency (in Hz) of the rtcclk */
> +#define RTCCLK_FREQ		1000000
> +
> +/ {
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +	model = "Microchip PolarFire-SoC Icicle Kit";
> +	compatible = "microchip,mpfs-icicle-kit";
> +
> +	chosen {
> +		stdout-path = &serial0;
> +	};
> +
> +	cpus {
> +		timebase-frequency = <RTCCLK_FREQ>;
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x0 0x80000000 0x0 0x40000000>;
> +		clocks = <&clkcfg 26>;
> +	};
> +

The latest Microchip releases have two memory nodes to provide the
full 2GiB of memory space.

> +	soc {
> +	};
> +};
> +
> +&serial0 {
> +	status = "okay";
> +};
> +
> +&serial1 {
> +	status = "okay";
> +};
> +
> +&serial2 {
> +	status = "okay";
> +};
> +
> +&serial3 {
> +	status = "okay";
> +};
> +
> +&sdcard {
> +	status = "okay";
> +};
> +
> +&emac0 {
> +	phy-mode = "sgmii";
> +	phy-handle = <&phy0>;
> +	phy0: ethernet-phy@8 {
> +		reg = <8>;
> +		ti,fifo-depth = <0x01>;
> +	};
> +};
> +
> +&emac1 {
> +	status = "okay";
> +	phy-mode = "sgmii";
> +	phy-handle = <&phy1>;
> +	phy1: ethernet-phy@9 {
> +		reg = <9>;
> +		ti,fifo-depth = <0x01>;
> +	};
> +};



-- 
Ben Dooks				http://www.codethink.co.uk/
Senior Engineer				Codethink - Providing Genius

https://www.codethink.co.uk/privacy.html

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
       [not found]     ` <DM6PR11MB3770E7FA8121AA91D9EDC4FEE5929@DM6PR11MB3770.namprd11.prod.outlook.com>
@ 2021-03-09 19:34       ` Atish Patra
  0 siblings, 0 replies; 21+ messages in thread
From: Atish Patra @ 2021-03-09 19:34 UTC (permalink / raw)
  To: ben.dooks, Lewis.Hanly, linux-kernel
  Cc: Cyril.Jean, linux-riscv, Alistair Francis, Anup Patel,
	Conor.Dooley, devicetree, bjorn, aou, palmer, paul.walmsley,
	Ivan.Griffin, Daire.McNamara, robh+dt

On Tue, 2021-03-09 at 13:30 +0000, Lewis.Hanly@microchip.com wrote:
> 
> 
> From: Ben Dooks <ben.dooks@codethink.co.uk>
> Sent: Tuesday, March 9, 2021 10:56 AM
> To: Atish Patra <atish.patra@wdc.com>; linux-kernel@vger.kernel.org <
> linux-kernel@vger.kernel.org>
> Cc: Albert Ou <aou@eecs.berkeley.edu>; Alistair Francis <
> alistair.francis@wdc.com>; Anup Patel <anup.patel@wdc.com>; Björn
> Töpel <bjorn@kernel.org>; devicetree@vger.kernel.org <
> devicetree@vger.kernel.org>; linux-riscv@lists.infradead.org <
> linux-riscv@lists.infradead.org>; Palmer Dabbelt
> <palmer@dabbelt.com>; Paul Walmsley <paul.walmsley@sifive.com>; Rob
> Herring < robh+dt@kernel.org>; Conor Dooley - M52691 <
> Conor.Dooley@microchip.com>; Daire McNamara - X61553 <
> Daire.McNamara@microchip.com>; Ivan Griffin - X61451 <
> Ivan.Griffin@microchip.com>; Lewis Hanly - M34782 <
> Lewis.Hanly@microchip.com>
> Subject: Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE
> board 
> EXTERNAL EMAIL: Do not click links or open attachments unless you
> know the content is safe
> 
> On 03/03/2021 20:02, Atish Patra wrote:
> > Add initial DTS for Microchip ICICLE board having only
> > essential devices (clocks, sdhci, ethernet, serial, etc).
> > The device tree is based on the U-Boot patch.
> > 
> > https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> > 
> > Signed-off-by: Atish Patra <atish.patra@wdc.com>
> > ---
> >    arch/riscv/boot/dts/Makefile                  |   1 +
> >    arch/riscv/boot/dts/microchip/Makefile        |   2 +
> >    .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> >    .../boot/dts/microchip/microchip-mpfs.dtsi    | 329
> > ++++++++++++++++++
> >    4 files changed, 404 insertions(+)
> >    create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> >    create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-
> > icicle-kit.dts
> >    create mode 100644 arch/riscv/boot/dts/microchip/microchip-
> > mpfs.dtsi
> > 
> > diff --git a/arch/riscv/boot/dts/Makefile
> > b/arch/riscv/boot/dts/Makefile
> > index 7ffd502e3e7b..fe996b88319e 100644
> > --- a/arch/riscv/boot/dts/Makefile
> > +++ b/arch/riscv/boot/dts/Makefile
> > @@ -1,5 +1,6 @@
> >    # SPDX-License-Identifier: GPL-2.0
> >    subdir-y += sifive
> >    subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > +subdir-y += microchip
> > 
> >    obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> > diff --git a/arch/riscv/boot/dts/microchip/Makefile
> > b/arch/riscv/boot/dts/microchip/Makefile
> > new file mode 100644
> > index 000000000000..622b12771fd3
> > --- /dev/null
> > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > @@ -0,0 +1,2 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-
> > kit.dtb
> > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-
> > kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-
> > kit.dts
> > new file mode 100644
> > index 000000000000..ec79944065c9
> > --- /dev/null
> > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > @@ -0,0 +1,72 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/* Copyright (c) 2020 Microchip Technology Inc */
> > +
> > +/dts-v1/;
> > +
> > +#include "microchip-mpfs.dtsi"
> > +
> > +/* Clock frequency (in Hz) of the rtcclk */
> > +#define RTCCLK_FREQ          1000000
> > +
> > +/ {
> > +     #address-cells = <2>;
> > +     #size-cells = <2>;
> > +     model = "Microchip PolarFire-SoC Icicle Kit";
> > +     compatible = "microchip,mpfs-icicle-kit";
> > +
> > +     chosen {
> > +             stdout-path = &serial0;
> > +     };
> > +
> > +     cpus {
> > +             timebase-frequency = <RTCCLK_FREQ>;
> > +     };
> > +
> > +     memory@80000000 {
> > +             device_type = "memory";
> > +             reg = <0x0 0x80000000 0x0 0x40000000>;
> > +             clocks = <&clkcfg 26>;
> > +     };
> > +
> 
> The latest Microchip releases have two memory nodes to provide the
> full 2GiB of memory space.
> > > For this release we want to leave it at 1GB, wip memory remapping
> > > with the newer releases.
> 

Thanks for the clarification. For some reason, your reply did not land
in the mailing lists.


> > +     soc {
> > +     };
> > +};
> > +
> > +&serial0 {
> > +     status = "okay";
> > +};
> > +
> > +&serial1 {
> > +     status = "okay";
> > +};
> > +
> > +&serial2 {
> > +     status = "okay";
> > +};
> > +
> > +&serial3 {
> > +     status = "okay";
> > +};
> > +
> > +&sdcard {
> > +     status = "okay";
> > +};
> > +
> > +&emac0 {
> > +     phy-mode = "sgmii";
> > +     phy-handle = <&phy0>;
> > +     phy0: ethernet-phy@8 {
> > +             reg = <8>;
> > +             ti,fifo-depth = <0x01>;
> > +     };
> > +};
> > +
> > +&emac1 {
> > +     status = "okay";
> > +     phy-mode = "sgmii";
> > +     phy-handle = <&phy1>;
> > +     phy1: ethernet-phy@9 {
> > +             reg = <9>;
> > +             ti,fifo-depth = <0x01>;
> > +     };
> > +};
> 
> 
> 
> --
> Ben Dooks                               http://www.codethink.co.uk/
> Senior Engineer                         Codethink - Providing Genius
> 
> https://www.codethink.co.uk/privacy.html

-- 
Regards,
Atish
_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-03-03 20:02 ` [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
  2021-03-09 10:56   ` Ben Dooks
@ 2021-03-22  6:04   ` Bin Meng
  2021-03-27 17:22   ` Alex Ghiti
  2 siblings, 0 replies; 21+ messages in thread
From: Bin Meng @ 2021-03-22  6:04 UTC (permalink / raw)
  To: Atish Patra
  Cc: linux-kernel, Albert Ou, Alistair Francis, Anup Patel,
	Björn Töpel, devicetree, linux-riscv, Palmer Dabbelt,
	Paul Walmsley, Rob Herring, Conor Dooley, Daire McNamara,
	Ivan.Griffin, Lewis.Hanly

On Thu, Mar 4, 2021 at 8:48 PM Atish Patra <atish.patra@wdc.com> wrote:
>
> Add initial DTS for Microchip ICICLE board having only
> essential devices (clocks, sdhci, ethernet, serial, etc).
> The device tree is based on the U-Boot patch.
>
> https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
>
> Signed-off-by: Atish Patra <atish.patra@wdc.com>
> ---
>  arch/riscv/boot/dts/Makefile                  |   1 +
>  arch/riscv/boot/dts/microchip/Makefile        |   2 +
>  .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
>  .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
>  4 files changed, 404 insertions(+)
>  create mode 100644 arch/riscv/boot/dts/microchip/Makefile
>  create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
>  create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
>

Reviewed-by: Bin Meng <bin.meng@windriver.com>

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-03-03 20:02 ` [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
  2021-03-09 10:56   ` Ben Dooks
  2021-03-22  6:04   ` Bin Meng
@ 2021-03-27 17:22   ` Alex Ghiti
  2021-03-28 15:22     ` Vitaly Wool
  2 siblings, 1 reply; 21+ messages in thread
From: Alex Ghiti @ 2021-03-27 17:22 UTC (permalink / raw)
  To: Atish Patra, linux-kernel
  Cc: Albert Ou, Alistair Francis, Anup Patel, Björn Töpel,
	devicetree, linux-riscv, Palmer Dabbelt, Paul Walmsley,
	Rob Herring, Conor.Dooley, Daire McNamara, Ivan.Griffin,
	Lewis.Hanly

Hi Atish,

Le 3/3/21 à 3:02 PM, Atish Patra a écrit :
> Add initial DTS for Microchip ICICLE board having only
> essential devices (clocks, sdhci, ethernet, serial, etc).
> The device tree is based on the U-Boot patch.
> 
> https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> 
> Signed-off-by: Atish Patra <atish.patra@wdc.com>
> ---
>   arch/riscv/boot/dts/Makefile                  |   1 +
>   arch/riscv/boot/dts/microchip/Makefile        |   2 +
>   .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
>   .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
>   4 files changed, 404 insertions(+)
>   create mode 100644 arch/riscv/boot/dts/microchip/Makefile
>   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
>   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> 
> diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> index 7ffd502e3e7b..fe996b88319e 100644
> --- a/arch/riscv/boot/dts/Makefile
> +++ b/arch/riscv/boot/dts/Makefile
> @@ -1,5 +1,6 @@
>   # SPDX-License-Identifier: GPL-2.0
>   subdir-y += sifive
>   subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> +subdir-y += microchip
>   
>   obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> new file mode 100644
> index 000000000000..622b12771fd3
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/Makefile
> @@ -0,0 +1,2 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb

I'm playing (or trying to...) with XIP_KERNEL and I had to add the 
following to have the device tree actually builtin the kernel:

diff --git a/arch/riscv/boot/dts/microchip/Makefile 
b/arch/riscv/boot/dts/microchip/Makefile
index 622b12771fd3..855c1502d912 100644
--- a/arch/riscv/boot/dts/microchip/Makefile
+++ b/arch/riscv/boot/dts/microchip/Makefile
@@ -1,2 +1,3 @@
  # SPDX-License-Identifier: GPL-2.0
  dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
+obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))

Alex

> diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> new file mode 100644
> index 000000000000..ec79944065c9
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> @@ -0,0 +1,72 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/* Copyright (c) 2020 Microchip Technology Inc */
> +
> +/dts-v1/;
> +
> +#include "microchip-mpfs.dtsi"
> +
> +/* Clock frequency (in Hz) of the rtcclk */
> +#define RTCCLK_FREQ		1000000
> +
> +/ {
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +	model = "Microchip PolarFire-SoC Icicle Kit";
> +	compatible = "microchip,mpfs-icicle-kit";
> +
> +	chosen {
> +		stdout-path = &serial0;
> +	};
> +
> +	cpus {
> +		timebase-frequency = <RTCCLK_FREQ>;
> +	};
> +
> +	memory@80000000 {
> +		device_type = "memory";
> +		reg = <0x0 0x80000000 0x0 0x40000000>;
> +		clocks = <&clkcfg 26>;
> +	};
> +
> +	soc {
> +	};
> +};
> +
> +&serial0 {
> +	status = "okay";
> +};
> +
> +&serial1 {
> +	status = "okay";
> +};
> +
> +&serial2 {
> +	status = "okay";
> +};
> +
> +&serial3 {
> +	status = "okay";
> +};
> +
> +&sdcard {
> +	status = "okay";
> +};
> +
> +&emac0 {
> +	phy-mode = "sgmii";
> +	phy-handle = <&phy0>;
> +	phy0: ethernet-phy@8 {
> +		reg = <8>;
> +		ti,fifo-depth = <0x01>;
> +	};
> +};
> +
> +&emac1 {
> +	status = "okay";
> +	phy-mode = "sgmii";
> +	phy-handle = <&phy1>;
> +	phy1: ethernet-phy@9 {
> +		reg = <9>;
> +		ti,fifo-depth = <0x01>;
> +	};
> +};
> diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> new file mode 100644
> index 000000000000..b9819570a7d1
> --- /dev/null
> +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> @@ -0,0 +1,329 @@
> +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> +/* Copyright (c) 2020 Microchip Technology Inc */
> +
> +/dts-v1/;
> +
> +/ {
> +	#address-cells = <2>;
> +	#size-cells = <2>;
> +	model = "Microchip MPFS Icicle Kit";
> +	compatible = "microchip,mpfs-icicle-kit";
> +
> +	chosen {
> +	};
> +
> +	cpus {
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		cpu@0 {
> +			clock-frequency = <0>;
> +			compatible = "sifive,e51", "sifive,rocket0", "riscv";
> +			device_type = "cpu";
> +			i-cache-block-size = <64>;
> +			i-cache-sets = <128>;
> +			i-cache-size = <16384>;
> +			reg = <0>;
> +			riscv,isa = "rv64imac";
> +			status = "disabled";
> +
> +			cpu0_intc: interrupt-controller {
> +				#interrupt-cells = <1>;
> +				compatible = "riscv,cpu-intc";
> +				interrupt-controller;
> +			};
> +		};
> +
> +		cpu@1 {
> +			clock-frequency = <0>;
> +			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> +			d-cache-block-size = <64>;
> +			d-cache-sets = <64>;
> +			d-cache-size = <32768>;
> +			d-tlb-sets = <1>;
> +			d-tlb-size = <32>;
> +			device_type = "cpu";
> +			i-cache-block-size = <64>;
> +			i-cache-sets = <64>;
> +			i-cache-size = <32768>;
> +			i-tlb-sets = <1>;
> +			i-tlb-size = <32>;
> +			mmu-type = "riscv,sv39";
> +			reg = <1>;
> +			riscv,isa = "rv64imafdc";
> +			tlb-split;
> +			status = "okay";
> +
> +			cpu1_intc: interrupt-controller {
> +				#interrupt-cells = <1>;
> +				compatible = "riscv,cpu-intc";
> +				interrupt-controller;
> +			};
> +		};
> +
> +		cpu@2 {
> +			clock-frequency = <0>;
> +			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> +			d-cache-block-size = <64>;
> +			d-cache-sets = <64>;
> +			d-cache-size = <32768>;
> +			d-tlb-sets = <1>;
> +			d-tlb-size = <32>;
> +			device_type = "cpu";
> +			i-cache-block-size = <64>;
> +			i-cache-sets = <64>;
> +			i-cache-size = <32768>;
> +			i-tlb-sets = <1>;
> +			i-tlb-size = <32>;
> +			mmu-type = "riscv,sv39";
> +			reg = <2>;
> +			riscv,isa = "rv64imafdc";
> +			tlb-split;
> +			status = "okay";
> +
> +			cpu2_intc: interrupt-controller {
> +				#interrupt-cells = <1>;
> +				compatible = "riscv,cpu-intc";
> +				interrupt-controller;
> +			};
> +		};
> +
> +		cpu@3 {
> +			clock-frequency = <0>;
> +			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> +			d-cache-block-size = <64>;
> +			d-cache-sets = <64>;
> +			d-cache-size = <32768>;
> +			d-tlb-sets = <1>;
> +			d-tlb-size = <32>;
> +			device_type = "cpu";
> +			i-cache-block-size = <64>;
> +			i-cache-sets = <64>;
> +			i-cache-size = <32768>;
> +			i-tlb-sets = <1>;
> +			i-tlb-size = <32>;
> +			mmu-type = "riscv,sv39";
> +			reg = <3>;
> +			riscv,isa = "rv64imafdc";
> +			tlb-split;
> +			status = "okay";
> +
> +			cpu3_intc: interrupt-controller {
> +				#interrupt-cells = <1>;
> +				compatible = "riscv,cpu-intc";
> +				interrupt-controller;
> +			};
> +		};
> +
> +		cpu@4 {
> +			clock-frequency = <0>;
> +			compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> +			d-cache-block-size = <64>;
> +			d-cache-sets = <64>;
> +			d-cache-size = <32768>;
> +			d-tlb-sets = <1>;
> +			d-tlb-size = <32>;
> +			device_type = "cpu";
> +			i-cache-block-size = <64>;
> +			i-cache-sets = <64>;
> +			i-cache-size = <32768>;
> +			i-tlb-sets = <1>;
> +			i-tlb-size = <32>;
> +			mmu-type = "riscv,sv39";
> +			reg = <4>;
> +			riscv,isa = "rv64imafdc";
> +			tlb-split;
> +			status = "okay";
> +			cpu4_intc: interrupt-controller {
> +				#interrupt-cells = <1>;
> +				compatible = "riscv,cpu-intc";
> +				interrupt-controller;
> +			};
> +		};
> +	};
> +
> +	soc {
> +		#address-cells = <2>;
> +		#size-cells = <2>;
> +		compatible = "simple-bus";
> +		ranges;
> +
> +		cache-controller@2010000 {
> +			compatible = "sifive,fu540-c000-ccache", "cache";
> +			cache-block-size = <64>;
> +			cache-level = <2>;
> +			cache-sets = <1024>;
> +			cache-size = <2097152>;
> +			cache-unified;
> +			interrupt-parent = <&plic>;
> +			interrupts = <1 2 3>;
> +			reg = <0x0 0x2010000 0x0 0x1000>;
> +		};
> +
> +		clint@2000000 {
> +			compatible = "sifive,clint0";
> +			reg = <0x0 0x2000000 0x0 0xC000>;
> +			interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> +						&cpu1_intc 3 &cpu1_intc 7
> +						&cpu2_intc 3 &cpu2_intc 7
> +						&cpu3_intc 3 &cpu3_intc 7
> +						&cpu4_intc 3 &cpu4_intc 7>;
> +		};
> +
> +		plic: interrupt-controller@c000000 {
> +			#interrupt-cells = <1>;
> +			compatible = "sifive,plic-1.0.0";
> +			reg = <0x0 0xc000000 0x0 0x4000000>;
> +			riscv,ndev = <186>;
> +			interrupt-controller;
> +			interrupts-extended = <&cpu0_intc 11
> +					&cpu1_intc 11 &cpu1_intc 9
> +					&cpu2_intc 11 &cpu2_intc 9
> +					&cpu3_intc 11 &cpu3_intc 9
> +					&cpu4_intc 11 &cpu4_intc 9>;
> +		};
> +
> +		dma@3000000 {
> +			compatible = "sifive,fu540-c000-pdma";
> +			reg = <0x0 0x3000000 0x0 0x8000>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <23 24 25 26 27 28 29 30>;
> +			#dma-cells = <1>;
> +		};
> +
> +		refclk: refclk {
> +			compatible = "fixed-clock";
> +			#clock-cells = <0>;
> +			clock-frequency = <600000000>;
> +			clock-output-names = "msspllclk";
> +		};
> +
> +		clkcfg: clkcfg@20002000 {
> +			compatible = "microchip,mpfs-clkcfg";
> +			reg = <0x0 0x20002000 0x0 0x1000>;
> +			reg-names = "mss_sysreg";
> +			clocks = <&refclk>;
> +			#clock-cells = <1>;
> +			clock-output-names = "cpu", "axi", "ahb", "envm",	/* 0-3   */
> +				 "mac0", "mac1", "mmc", "timer",		/* 4-7   */
> +				"mmuart0", "mmuart1", "mmuart2", "mmuart3",	/* 8-11  */
> +				"mmuart4", "spi0", "spi1", "i2c0",		/* 12-15 */
> +				"i2c1", "can0", "can1", "usb",			/* 16-19 */
> +				"rsvd", "rtc", "qspi", "gpio0",			/* 20-23 */
> +				"gpio1", "gpio2", "ddrc", "fic0",		/* 24-27 */
> +				"fic1", "fic2", "fic3", "athena", "cfm";	/* 28-32 */
> +		};
> +
> +		serial0: serial@20000000 {
> +			compatible = "ns16550a";
> +			reg = <0x0 0x20000000 0x0 0x400>;
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <90>;
> +			current-speed = <115200>;
> +			clocks = <&clkcfg 8>;
> +			status = "disabled";
> +		};
> +
> +		serial1: serial@20100000 {
> +			compatible = "ns16550a";
> +			reg = <0x0 0x20100000 0x0 0x400>;
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <91>;
> +			current-speed = <115200>;
> +			clocks = <&clkcfg 9>;
> +			status = "disabled";
> +		};
> +
> +		serial2: serial@20102000 {
> +			compatible = "ns16550a";
> +			reg = <0x0 0x20102000 0x0 0x400>;
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <92>;
> +			current-speed = <115200>;
> +			clocks = <&clkcfg 10>;
> +			status = "disabled";
> +		};
> +
> +		serial3: serial@20104000 {
> +			compatible = "ns16550a";
> +			reg = <0x0 0x20104000 0x0 0x400>;
> +			reg-io-width = <4>;
> +			reg-shift = <2>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <93>;
> +			current-speed = <115200>;
> +			clocks = <&clkcfg 11>;
> +			status = "disabled";
> +		};
> +
> +		emmc: mmc@20008000 {
> +			compatible = "cdns,sd4hc";
> +			reg = <0x0 0x20008000 0x0 0x1000>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <88 89>;
> +			pinctrl-names = "default";
> +			clocks = <&clkcfg 6>;
> +			bus-width = <4>;
> +			cap-mmc-highspeed;
> +			mmc-ddr-3_3v;
> +			max-frequency = <200000000>;
> +			non-removable;
> +			no-sd;
> +			no-sdio;
> +			voltage-ranges = <3300 3300>;
> +			status = "disabled";
> +		};
> +
> +		sdcard: sdhc@20008000 {
> +			compatible = "cdns,sd4hc";
> +			reg = <0x0 0x20008000 0x0 0x1000>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <88>;
> +			pinctrl-names = "default";
> +			clocks = <&clkcfg 6>;
> +			bus-width = <4>;
> +			disable-wp;
> +			cap-sd-highspeed;
> +			card-detect-delay = <200>;
> +			sd-uhs-sdr12;
> +			sd-uhs-sdr25;
> +			sd-uhs-sdr50;
> +			sd-uhs-sdr104;
> +			max-frequency = <200000000>;
> +			status = "disabled";
> +		};
> +
> +		emac0: ethernet@20110000 {
> +			compatible = "cdns,macb";
> +			reg = <0x0 0x20110000 0x0 0x2000>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <64 65 66 67>;
> +			local-mac-address = [00 00 00 00 00 00];
> +			clocks = <&clkcfg 4>, <&clkcfg 2>;
> +			clock-names = "pclk", "hclk";
> +			status = "disabled";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +		emac1: ethernet@20112000 {
> +			compatible = "cdns,macb";
> +			reg = <0x0 0x20112000 0x0 0x2000>;
> +			interrupt-parent = <&plic>;
> +			interrupts = <70 71 72 73>;
> +			mac-address = [00 00 00 00 00 00];
> +			clocks = <&clkcfg 5>, <&clkcfg 2>;
> +			status = "disabled";
> +			clock-names = "pclk", "hclk";
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +		};
> +
> +	};
> +};
> 

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-03-27 17:22   ` Alex Ghiti
@ 2021-03-28 15:22     ` Vitaly Wool
  2021-04-18  3:36       ` Atish Patra
  0 siblings, 1 reply; 21+ messages in thread
From: Vitaly Wool @ 2021-03-28 15:22 UTC (permalink / raw)
  To: Alex Ghiti
  Cc: Atish Patra, LKML, Albert Ou, Alistair Francis, Anup Patel,
	Björn Töpel, devicetree, linux-riscv, Palmer Dabbelt,
	Paul Walmsley, Rob Herring, Conor.Dooley, Daire McNamara,
	Ivan.Griffin, Lewis.Hanly

On Sat, Mar 27, 2021 at 6:24 PM Alex Ghiti <alex@ghiti.fr> wrote:
>
> Hi Atish,
>
> Le 3/3/21 à 3:02 PM, Atish Patra a écrit :
> > Add initial DTS for Microchip ICICLE board having only
> > essential devices (clocks, sdhci, ethernet, serial, etc).
> > The device tree is based on the U-Boot patch.
> >
> > https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> >
> > Signed-off-by: Atish Patra <atish.patra@wdc.com>
> > ---
> >   arch/riscv/boot/dts/Makefile                  |   1 +
> >   arch/riscv/boot/dts/microchip/Makefile        |   2 +
> >   .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> >   .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> >   4 files changed, 404 insertions(+)
> >   create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> >
> > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> > index 7ffd502e3e7b..fe996b88319e 100644
> > --- a/arch/riscv/boot/dts/Makefile
> > +++ b/arch/riscv/boot/dts/Makefile
> > @@ -1,5 +1,6 @@
> >   # SPDX-License-Identifier: GPL-2.0
> >   subdir-y += sifive
> >   subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > +subdir-y += microchip
> >
> >   obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> > diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> > new file mode 100644
> > index 000000000000..622b12771fd3
> > --- /dev/null
> > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > @@ -0,0 +1,2 @@
> > +# SPDX-License-Identifier: GPL-2.0
> > +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
>
> I'm playing (or trying to...) with XIP_KERNEL and I had to add the
> following to have the device tree actually builtin the kernel:
>
> diff --git a/arch/riscv/boot/dts/microchip/Makefile
> b/arch/riscv/boot/dts/microchip/Makefile
> index 622b12771fd3..855c1502d912 100644
> --- a/arch/riscv/boot/dts/microchip/Makefile
> +++ b/arch/riscv/boot/dts/microchip/Makefile
> @@ -1,2 +1,3 @@
>   # SPDX-License-Identifier: GPL-2.0
>   dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> +obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
>
> Alex

Yes, I believe this is necessary for BUILTIN_DTB to work on Polarfire,
regardless of whether the kernel is XIP or not.

Best regards,
   Vitaly

> > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > new file mode 100644
> > index 000000000000..ec79944065c9
> > --- /dev/null
> > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > @@ -0,0 +1,72 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/* Copyright (c) 2020 Microchip Technology Inc */
> > +
> > +/dts-v1/;
> > +
> > +#include "microchip-mpfs.dtsi"
> > +
> > +/* Clock frequency (in Hz) of the rtcclk */
> > +#define RTCCLK_FREQ          1000000
> > +
> > +/ {
> > +     #address-cells = <2>;
> > +     #size-cells = <2>;
> > +     model = "Microchip PolarFire-SoC Icicle Kit";
> > +     compatible = "microchip,mpfs-icicle-kit";
> > +
> > +     chosen {
> > +             stdout-path = &serial0;
> > +     };
> > +
> > +     cpus {
> > +             timebase-frequency = <RTCCLK_FREQ>;
> > +     };
> > +
> > +     memory@80000000 {
> > +             device_type = "memory";
> > +             reg = <0x0 0x80000000 0x0 0x40000000>;
> > +             clocks = <&clkcfg 26>;
> > +     };
> > +
> > +     soc {
> > +     };
> > +};
> > +
> > +&serial0 {
> > +     status = "okay";
> > +};
> > +
> > +&serial1 {
> > +     status = "okay";
> > +};
> > +
> > +&serial2 {
> > +     status = "okay";
> > +};
> > +
> > +&serial3 {
> > +     status = "okay";
> > +};
> > +
> > +&sdcard {
> > +     status = "okay";
> > +};
> > +
> > +&emac0 {
> > +     phy-mode = "sgmii";
> > +     phy-handle = <&phy0>;
> > +     phy0: ethernet-phy@8 {
> > +             reg = <8>;
> > +             ti,fifo-depth = <0x01>;
> > +     };
> > +};
> > +
> > +&emac1 {
> > +     status = "okay";
> > +     phy-mode = "sgmii";
> > +     phy-handle = <&phy1>;
> > +     phy1: ethernet-phy@9 {
> > +             reg = <9>;
> > +             ti,fifo-depth = <0x01>;
> > +     };
> > +};
> > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > new file mode 100644
> > index 000000000000..b9819570a7d1
> > --- /dev/null
> > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > @@ -0,0 +1,329 @@
> > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > +/* Copyright (c) 2020 Microchip Technology Inc */
> > +
> > +/dts-v1/;
> > +
> > +/ {
> > +     #address-cells = <2>;
> > +     #size-cells = <2>;
> > +     model = "Microchip MPFS Icicle Kit";
> > +     compatible = "microchip,mpfs-icicle-kit";
> > +
> > +     chosen {
> > +     };
> > +
> > +     cpus {
> > +             #address-cells = <1>;
> > +             #size-cells = <0>;
> > +
> > +             cpu@0 {
> > +                     clock-frequency = <0>;
> > +                     compatible = "sifive,e51", "sifive,rocket0", "riscv";
> > +                     device_type = "cpu";
> > +                     i-cache-block-size = <64>;
> > +                     i-cache-sets = <128>;
> > +                     i-cache-size = <16384>;
> > +                     reg = <0>;
> > +                     riscv,isa = "rv64imac";
> > +                     status = "disabled";
> > +
> > +                     cpu0_intc: interrupt-controller {
> > +                             #interrupt-cells = <1>;
> > +                             compatible = "riscv,cpu-intc";
> > +                             interrupt-controller;
> > +                     };
> > +             };
> > +
> > +             cpu@1 {
> > +                     clock-frequency = <0>;
> > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > +                     d-cache-block-size = <64>;
> > +                     d-cache-sets = <64>;
> > +                     d-cache-size = <32768>;
> > +                     d-tlb-sets = <1>;
> > +                     d-tlb-size = <32>;
> > +                     device_type = "cpu";
> > +                     i-cache-block-size = <64>;
> > +                     i-cache-sets = <64>;
> > +                     i-cache-size = <32768>;
> > +                     i-tlb-sets = <1>;
> > +                     i-tlb-size = <32>;
> > +                     mmu-type = "riscv,sv39";
> > +                     reg = <1>;
> > +                     riscv,isa = "rv64imafdc";
> > +                     tlb-split;
> > +                     status = "okay";
> > +
> > +                     cpu1_intc: interrupt-controller {
> > +                             #interrupt-cells = <1>;
> > +                             compatible = "riscv,cpu-intc";
> > +                             interrupt-controller;
> > +                     };
> > +             };
> > +
> > +             cpu@2 {
> > +                     clock-frequency = <0>;
> > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > +                     d-cache-block-size = <64>;
> > +                     d-cache-sets = <64>;
> > +                     d-cache-size = <32768>;
> > +                     d-tlb-sets = <1>;
> > +                     d-tlb-size = <32>;
> > +                     device_type = "cpu";
> > +                     i-cache-block-size = <64>;
> > +                     i-cache-sets = <64>;
> > +                     i-cache-size = <32768>;
> > +                     i-tlb-sets = <1>;
> > +                     i-tlb-size = <32>;
> > +                     mmu-type = "riscv,sv39";
> > +                     reg = <2>;
> > +                     riscv,isa = "rv64imafdc";
> > +                     tlb-split;
> > +                     status = "okay";
> > +
> > +                     cpu2_intc: interrupt-controller {
> > +                             #interrupt-cells = <1>;
> > +                             compatible = "riscv,cpu-intc";
> > +                             interrupt-controller;
> > +                     };
> > +             };
> > +
> > +             cpu@3 {
> > +                     clock-frequency = <0>;
> > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > +                     d-cache-block-size = <64>;
> > +                     d-cache-sets = <64>;
> > +                     d-cache-size = <32768>;
> > +                     d-tlb-sets = <1>;
> > +                     d-tlb-size = <32>;
> > +                     device_type = "cpu";
> > +                     i-cache-block-size = <64>;
> > +                     i-cache-sets = <64>;
> > +                     i-cache-size = <32768>;
> > +                     i-tlb-sets = <1>;
> > +                     i-tlb-size = <32>;
> > +                     mmu-type = "riscv,sv39";
> > +                     reg = <3>;
> > +                     riscv,isa = "rv64imafdc";
> > +                     tlb-split;
> > +                     status = "okay";
> > +
> > +                     cpu3_intc: interrupt-controller {
> > +                             #interrupt-cells = <1>;
> > +                             compatible = "riscv,cpu-intc";
> > +                             interrupt-controller;
> > +                     };
> > +             };
> > +
> > +             cpu@4 {
> > +                     clock-frequency = <0>;
> > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > +                     d-cache-block-size = <64>;
> > +                     d-cache-sets = <64>;
> > +                     d-cache-size = <32768>;
> > +                     d-tlb-sets = <1>;
> > +                     d-tlb-size = <32>;
> > +                     device_type = "cpu";
> > +                     i-cache-block-size = <64>;
> > +                     i-cache-sets = <64>;
> > +                     i-cache-size = <32768>;
> > +                     i-tlb-sets = <1>;
> > +                     i-tlb-size = <32>;
> > +                     mmu-type = "riscv,sv39";
> > +                     reg = <4>;
> > +                     riscv,isa = "rv64imafdc";
> > +                     tlb-split;
> > +                     status = "okay";
> > +                     cpu4_intc: interrupt-controller {
> > +                             #interrupt-cells = <1>;
> > +                             compatible = "riscv,cpu-intc";
> > +                             interrupt-controller;
> > +                     };
> > +             };
> > +     };
> > +
> > +     soc {
> > +             #address-cells = <2>;
> > +             #size-cells = <2>;
> > +             compatible = "simple-bus";
> > +             ranges;
> > +
> > +             cache-controller@2010000 {
> > +                     compatible = "sifive,fu540-c000-ccache", "cache";
> > +                     cache-block-size = <64>;
> > +                     cache-level = <2>;
> > +                     cache-sets = <1024>;
> > +                     cache-size = <2097152>;
> > +                     cache-unified;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <1 2 3>;
> > +                     reg = <0x0 0x2010000 0x0 0x1000>;
> > +             };
> > +
> > +             clint@2000000 {
> > +                     compatible = "sifive,clint0";
> > +                     reg = <0x0 0x2000000 0x0 0xC000>;
> > +                     interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> > +                                             &cpu1_intc 3 &cpu1_intc 7
> > +                                             &cpu2_intc 3 &cpu2_intc 7
> > +                                             &cpu3_intc 3 &cpu3_intc 7
> > +                                             &cpu4_intc 3 &cpu4_intc 7>;
> > +             };
> > +
> > +             plic: interrupt-controller@c000000 {
> > +                     #interrupt-cells = <1>;
> > +                     compatible = "sifive,plic-1.0.0";
> > +                     reg = <0x0 0xc000000 0x0 0x4000000>;
> > +                     riscv,ndev = <186>;
> > +                     interrupt-controller;
> > +                     interrupts-extended = <&cpu0_intc 11
> > +                                     &cpu1_intc 11 &cpu1_intc 9
> > +                                     &cpu2_intc 11 &cpu2_intc 9
> > +                                     &cpu3_intc 11 &cpu3_intc 9
> > +                                     &cpu4_intc 11 &cpu4_intc 9>;
> > +             };
> > +
> > +             dma@3000000 {
> > +                     compatible = "sifive,fu540-c000-pdma";
> > +                     reg = <0x0 0x3000000 0x0 0x8000>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <23 24 25 26 27 28 29 30>;
> > +                     #dma-cells = <1>;
> > +             };
> > +
> > +             refclk: refclk {
> > +                     compatible = "fixed-clock";
> > +                     #clock-cells = <0>;
> > +                     clock-frequency = <600000000>;
> > +                     clock-output-names = "msspllclk";
> > +             };
> > +
> > +             clkcfg: clkcfg@20002000 {
> > +                     compatible = "microchip,mpfs-clkcfg";
> > +                     reg = <0x0 0x20002000 0x0 0x1000>;
> > +                     reg-names = "mss_sysreg";
> > +                     clocks = <&refclk>;
> > +                     #clock-cells = <1>;
> > +                     clock-output-names = "cpu", "axi", "ahb", "envm",       /* 0-3   */
> > +                              "mac0", "mac1", "mmc", "timer",                /* 4-7   */
> > +                             "mmuart0", "mmuart1", "mmuart2", "mmuart3",     /* 8-11  */
> > +                             "mmuart4", "spi0", "spi1", "i2c0",              /* 12-15 */
> > +                             "i2c1", "can0", "can1", "usb",                  /* 16-19 */
> > +                             "rsvd", "rtc", "qspi", "gpio0",                 /* 20-23 */
> > +                             "gpio1", "gpio2", "ddrc", "fic0",               /* 24-27 */
> > +                             "fic1", "fic2", "fic3", "athena", "cfm";        /* 28-32 */
> > +             };
> > +
> > +             serial0: serial@20000000 {
> > +                     compatible = "ns16550a";
> > +                     reg = <0x0 0x20000000 0x0 0x400>;
> > +                     reg-io-width = <4>;
> > +                     reg-shift = <2>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <90>;
> > +                     current-speed = <115200>;
> > +                     clocks = <&clkcfg 8>;
> > +                     status = "disabled";
> > +             };
> > +
> > +             serial1: serial@20100000 {
> > +                     compatible = "ns16550a";
> > +                     reg = <0x0 0x20100000 0x0 0x400>;
> > +                     reg-io-width = <4>;
> > +                     reg-shift = <2>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <91>;
> > +                     current-speed = <115200>;
> > +                     clocks = <&clkcfg 9>;
> > +                     status = "disabled";
> > +             };
> > +
> > +             serial2: serial@20102000 {
> > +                     compatible = "ns16550a";
> > +                     reg = <0x0 0x20102000 0x0 0x400>;
> > +                     reg-io-width = <4>;
> > +                     reg-shift = <2>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <92>;
> > +                     current-speed = <115200>;
> > +                     clocks = <&clkcfg 10>;
> > +                     status = "disabled";
> > +             };
> > +
> > +             serial3: serial@20104000 {
> > +                     compatible = "ns16550a";
> > +                     reg = <0x0 0x20104000 0x0 0x400>;
> > +                     reg-io-width = <4>;
> > +                     reg-shift = <2>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <93>;
> > +                     current-speed = <115200>;
> > +                     clocks = <&clkcfg 11>;
> > +                     status = "disabled";
> > +             };
> > +
> > +             emmc: mmc@20008000 {
> > +                     compatible = "cdns,sd4hc";
> > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <88 89>;
> > +                     pinctrl-names = "default";
> > +                     clocks = <&clkcfg 6>;
> > +                     bus-width = <4>;
> > +                     cap-mmc-highspeed;
> > +                     mmc-ddr-3_3v;
> > +                     max-frequency = <200000000>;
> > +                     non-removable;
> > +                     no-sd;
> > +                     no-sdio;
> > +                     voltage-ranges = <3300 3300>;
> > +                     status = "disabled";
> > +             };
> > +
> > +             sdcard: sdhc@20008000 {
> > +                     compatible = "cdns,sd4hc";
> > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <88>;
> > +                     pinctrl-names = "default";
> > +                     clocks = <&clkcfg 6>;
> > +                     bus-width = <4>;
> > +                     disable-wp;
> > +                     cap-sd-highspeed;
> > +                     card-detect-delay = <200>;
> > +                     sd-uhs-sdr12;
> > +                     sd-uhs-sdr25;
> > +                     sd-uhs-sdr50;
> > +                     sd-uhs-sdr104;
> > +                     max-frequency = <200000000>;
> > +                     status = "disabled";
> > +             };
> > +
> > +             emac0: ethernet@20110000 {
> > +                     compatible = "cdns,macb";
> > +                     reg = <0x0 0x20110000 0x0 0x2000>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <64 65 66 67>;
> > +                     local-mac-address = [00 00 00 00 00 00];
> > +                     clocks = <&clkcfg 4>, <&clkcfg 2>;
> > +                     clock-names = "pclk", "hclk";
> > +                     status = "disabled";
> > +                     #address-cells = <1>;
> > +                     #size-cells = <0>;
> > +             };
> > +
> > +             emac1: ethernet@20112000 {
> > +                     compatible = "cdns,macb";
> > +                     reg = <0x0 0x20112000 0x0 0x2000>;
> > +                     interrupt-parent = <&plic>;
> > +                     interrupts = <70 71 72 73>;
> > +                     mac-address = [00 00 00 00 00 00];
> > +                     clocks = <&clkcfg 5>, <&clkcfg 2>;
> > +                     status = "disabled";
> > +                     clock-names = "pclk", "hclk";
> > +                     #address-cells = <1>;
> > +                     #size-cells = <0>;
> > +             };
> > +
> > +     };
> > +};
> >
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 0/5] Add Microchip PolarFire Soc Support
  2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
                   ` (4 preceding siblings ...)
  2021-03-03 20:02 ` [PATCH v4 5/5] MAINTAINERS: add microchip polarfire soc support Atish Patra
@ 2021-03-30  4:17 ` Palmer Dabbelt
  2021-04-18  3:26   ` Atish Patra
  5 siblings, 1 reply; 21+ messages in thread
From: Palmer Dabbelt @ 2021-03-30  4:17 UTC (permalink / raw)
  To: Atish Patra
  Cc: linux-kernel, Atish Patra, aou, Alistair Francis, Anup Patel,
	bjorn, devicetree, linux-riscv, Paul Walmsley, robh+dt,
	Conor.Dooley, daire.mcnamara, Ivan.Griffin, Lewis.Hanly

On Wed, 03 Mar 2021 12:02:48 PST (-0800), Atish Patra wrote:
> This series adds minimal support for Microchip Polar Fire Soc Icicle kit.
> It is rebased on v5.12-rc1 and depends on clock support.
> Only MMC and ethernet drivers are enabled via this series.
> The idea here is to add the foundational patches so that other drivers
> can be added to on top of this. The device tree may change based on
> feedback on bindings of individual driver support patches.
>
> This series has been tested on Qemu and Polar Fire Soc Icicle kit.
> It depends on the updated clock-series[2] and macb fix[3].
> The series is also tested by Lewis from Microchip.
>
> The series can also be found at.
> https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4
>
> [1] https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
> [2] https://www.spinics.net/lists/linux-clk/msg54579.html
>
> Changes from v3->v4:
> 1. Fixed few DT specific issues.
> 2. Rebased on top of new clock driver.
> 3. SD card functionality is verified.
>
> Changes from v2->v3:
> 1. Fixed a typo in dt binding.
> 2. Included MAINTAINERS entry for PolarFire SoC.
> 3. Improved the dts file by using lowercase clock names and keeping phy
>    details in board specific dts file.
>
> Changes from v1->v2:
> 1. Modified the DT to match the device tree in U-Boot.
> 2. Added both eMMC & SDcard entries in DT. However, SD card is only enabled
>    as it allows larger storage option for linux distros.
>
> Atish Patra (4):
> RISC-V: Add Microchip PolarFire SoC kconfig option
> dt-bindings: riscv: microchip: Add YAML documentation for the
> PolarFire SoC
> RISC-V: Initial DTS for Microchip ICICLE board
> RISC-V: Enable Microchip PolarFire ICICLE SoC
>
> Conor Dooley (1):
> MAINTAINERS: add microchip polarfire soc support
>
> .../devicetree/bindings/riscv/microchip.yaml  |  27 ++
> MAINTAINERS                                   |   8 +
> arch/riscv/Kconfig.socs                       |   7 +
> arch/riscv/boot/dts/Makefile                  |   1 +
> arch/riscv/boot/dts/microchip/Makefile        |   2 +
> .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> arch/riscv/configs/defconfig                  |   4 +
> 8 files changed, 450 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml
> create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi

I had this left in my inbox waiting for either some reviews to come in or a v2,
but I don't see any.  Did I miss something?

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 0/5] Add Microchip PolarFire Soc Support
  2021-03-30  4:17 ` [PATCH v4 0/5] Add Microchip PolarFire Soc Support Palmer Dabbelt
@ 2021-04-18  3:26   ` Atish Patra
  2021-04-22 22:33     ` Atish Patra
  0 siblings, 1 reply; 21+ messages in thread
From: Atish Patra @ 2021-04-18  3:26 UTC (permalink / raw)
  To: Palmer Dabbelt
  Cc: Atish Patra, linux-kernel@vger.kernel.org List, Albert Ou,
	Alistair Francis, Anup Patel, bjorn, devicetree, linux-riscv,
	Paul Walmsley, Rob Herring, Conor.Dooley, Daire McNamara,
	Ivan.Griffin, Lewis.Hanly

On Mon, Mar 29, 2021 at 9:17 PM Palmer Dabbelt <palmer@dabbelt.com> wrote:
>
> On Wed, 03 Mar 2021 12:02:48 PST (-0800), Atish Patra wrote:
> > This series adds minimal support for Microchip Polar Fire Soc Icicle kit.
> > It is rebased on v5.12-rc1 and depends on clock support.
> > Only MMC and ethernet drivers are enabled via this series.
> > The idea here is to add the foundational patches so that other drivers
> > can be added to on top of this. The device tree may change based on
> > feedback on bindings of individual driver support patches.
> >
> > This series has been tested on Qemu and Polar Fire Soc Icicle kit.
> > It depends on the updated clock-series[2] and macb fix[3].
> > The series is also tested by Lewis from Microchip.
> >
> > The series can also be found at.
> > https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4
> >
> > [1] https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
> > [2] https://www.spinics.net/lists/linux-clk/msg54579.html
> >
> > Changes from v3->v4:
> > 1. Fixed few DT specific issues.
> > 2. Rebased on top of new clock driver.
> > 3. SD card functionality is verified.
> >
> > Changes from v2->v3:
> > 1. Fixed a typo in dt binding.
> > 2. Included MAINTAINERS entry for PolarFire SoC.
> > 3. Improved the dts file by using lowercase clock names and keeping phy
> >    details in board specific dts file.
> >
> > Changes from v1->v2:
> > 1. Modified the DT to match the device tree in U-Boot.
> > 2. Added both eMMC & SDcard entries in DT. However, SD card is only enabled
> >    as it allows larger storage option for linux distros.
> >
> > Atish Patra (4):
> > RISC-V: Add Microchip PolarFire SoC kconfig option
> > dt-bindings: riscv: microchip: Add YAML documentation for the
> > PolarFire SoC
> > RISC-V: Initial DTS for Microchip ICICLE board
> > RISC-V: Enable Microchip PolarFire ICICLE SoC
> >
> > Conor Dooley (1):
> > MAINTAINERS: add microchip polarfire soc support
> >
> > .../devicetree/bindings/riscv/microchip.yaml  |  27 ++
> > MAINTAINERS                                   |   8 +
> > arch/riscv/Kconfig.socs                       |   7 +
> > arch/riscv/boot/dts/Makefile                  |   1 +
> > arch/riscv/boot/dts/microchip/Makefile        |   2 +
> > .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> > .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> > arch/riscv/configs/defconfig                  |   4 +
> > 8 files changed, 450 insertions(+)
> > create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml
> > create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> > create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
>
> I had this left in my inbox waiting for either some reviews to come in or a v2,
> but I don't see any.  Did I miss something?
>
Sorry for the late reply. I am on vacation until May. I think I saw
all the patches have already been reviewed.
Let me know if it is not the case.

> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv



-- 
Regards,
Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-03-28 15:22     ` Vitaly Wool
@ 2021-04-18  3:36       ` Atish Patra
  2021-04-18  4:24         ` Atish Patra
  2021-04-18 18:39         ` Vitaly Wool
  0 siblings, 2 replies; 21+ messages in thread
From: Atish Patra @ 2021-04-18  3:36 UTC (permalink / raw)
  To: Vitaly Wool
  Cc: Alex Ghiti, Atish Patra, LKML, Albert Ou, Alistair Francis,
	Anup Patel, Björn Töpel, devicetree, linux-riscv,
	Palmer Dabbelt, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

On Mon, Mar 29, 2021 at 10:04 AM Vitaly Wool <vitaly.wool@konsulko.com> wrote:
>
> On Sat, Mar 27, 2021 at 6:24 PM Alex Ghiti <alex@ghiti.fr> wrote:
> >
> > Hi Atish,
> >
> > Le 3/3/21 à 3:02 PM, Atish Patra a écrit :
> > > Add initial DTS for Microchip ICICLE board having only
> > > essential devices (clocks, sdhci, ethernet, serial, etc).
> > > The device tree is based on the U-Boot patch.
> > >
> > > https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> > >
> > > Signed-off-by: Atish Patra <atish.patra@wdc.com>
> > > ---
> > >   arch/riscv/boot/dts/Makefile                  |   1 +
> > >   arch/riscv/boot/dts/microchip/Makefile        |   2 +
> > >   .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> > >   .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> > >   4 files changed, 404 insertions(+)
> > >   create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> > >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > >
> > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> > > index 7ffd502e3e7b..fe996b88319e 100644
> > > --- a/arch/riscv/boot/dts/Makefile
> > > +++ b/arch/riscv/boot/dts/Makefile
> > > @@ -1,5 +1,6 @@
> > >   # SPDX-License-Identifier: GPL-2.0
> > >   subdir-y += sifive
> > >   subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > > +subdir-y += microchip
> > >
> > >   obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> > > diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> > > new file mode 100644
> > > index 000000000000..622b12771fd3
> > > --- /dev/null
> > > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > > @@ -0,0 +1,2 @@
> > > +# SPDX-License-Identifier: GPL-2.0
> > > +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> >
> > I'm playing (or trying to...) with XIP_KERNEL and I had to add the
> > following to have the device tree actually builtin the kernel:
> >
> > diff --git a/arch/riscv/boot/dts/microchip/Makefile
> > b/arch/riscv/boot/dts/microchip/Makefile
> > index 622b12771fd3..855c1502d912 100644
> > --- a/arch/riscv/boot/dts/microchip/Makefile
> > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > @@ -1,2 +1,3 @@
> >   # SPDX-License-Identifier: GPL-2.0
> >   dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> > +obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
> >
> > Alex
>
> Yes, I believe this is necessary for BUILTIN_DTB to work on Polarfire,
> regardless of whether the kernel is XIP or not.
>

But there is no usecase for BUILTIN_DTB for polarfire except XIP kernel.
The bootloaders for polarfire is capable of providing a DTB to kernel.

If XIP kernel is enabled, the following line in
arch/riscv/boot/dts/Makefile should take care of things


> Best regards,
>    Vitaly
>
> > > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > new file mode 100644
> > > index 000000000000..ec79944065c9
> > > --- /dev/null
> > > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > @@ -0,0 +1,72 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/* Copyright (c) 2020 Microchip Technology Inc */
> > > +
> > > +/dts-v1/;
> > > +
> > > +#include "microchip-mpfs.dtsi"
> > > +
> > > +/* Clock frequency (in Hz) of the rtcclk */
> > > +#define RTCCLK_FREQ          1000000
> > > +
> > > +/ {
> > > +     #address-cells = <2>;
> > > +     #size-cells = <2>;
> > > +     model = "Microchip PolarFire-SoC Icicle Kit";
> > > +     compatible = "microchip,mpfs-icicle-kit";
> > > +
> > > +     chosen {
> > > +             stdout-path = &serial0;
> > > +     };
> > > +
> > > +     cpus {
> > > +             timebase-frequency = <RTCCLK_FREQ>;
> > > +     };
> > > +
> > > +     memory@80000000 {
> > > +             device_type = "memory";
> > > +             reg = <0x0 0x80000000 0x0 0x40000000>;
> > > +             clocks = <&clkcfg 26>;
> > > +     };
> > > +
> > > +     soc {
> > > +     };
> > > +};
> > > +
> > > +&serial0 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&serial1 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&serial2 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&serial3 {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&sdcard {
> > > +     status = "okay";
> > > +};
> > > +
> > > +&emac0 {
> > > +     phy-mode = "sgmii";
> > > +     phy-handle = <&phy0>;
> > > +     phy0: ethernet-phy@8 {
> > > +             reg = <8>;
> > > +             ti,fifo-depth = <0x01>;
> > > +     };
> > > +};
> > > +
> > > +&emac1 {
> > > +     status = "okay";
> > > +     phy-mode = "sgmii";
> > > +     phy-handle = <&phy1>;
> > > +     phy1: ethernet-phy@9 {
> > > +             reg = <9>;
> > > +             ti,fifo-depth = <0x01>;
> > > +     };
> > > +};
> > > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > new file mode 100644
> > > index 000000000000..b9819570a7d1
> > > --- /dev/null
> > > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > @@ -0,0 +1,329 @@
> > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > +/* Copyright (c) 2020 Microchip Technology Inc */
> > > +
> > > +/dts-v1/;
> > > +
> > > +/ {
> > > +     #address-cells = <2>;
> > > +     #size-cells = <2>;
> > > +     model = "Microchip MPFS Icicle Kit";
> > > +     compatible = "microchip,mpfs-icicle-kit";
> > > +
> > > +     chosen {
> > > +     };
> > > +
> > > +     cpus {
> > > +             #address-cells = <1>;
> > > +             #size-cells = <0>;
> > > +
> > > +             cpu@0 {
> > > +                     clock-frequency = <0>;
> > > +                     compatible = "sifive,e51", "sifive,rocket0", "riscv";
> > > +                     device_type = "cpu";
> > > +                     i-cache-block-size = <64>;
> > > +                     i-cache-sets = <128>;
> > > +                     i-cache-size = <16384>;
> > > +                     reg = <0>;
> > > +                     riscv,isa = "rv64imac";
> > > +                     status = "disabled";
> > > +
> > > +                     cpu0_intc: interrupt-controller {
> > > +                             #interrupt-cells = <1>;
> > > +                             compatible = "riscv,cpu-intc";
> > > +                             interrupt-controller;
> > > +                     };
> > > +             };
> > > +
> > > +             cpu@1 {
> > > +                     clock-frequency = <0>;
> > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > +                     d-cache-block-size = <64>;
> > > +                     d-cache-sets = <64>;
> > > +                     d-cache-size = <32768>;
> > > +                     d-tlb-sets = <1>;
> > > +                     d-tlb-size = <32>;
> > > +                     device_type = "cpu";
> > > +                     i-cache-block-size = <64>;
> > > +                     i-cache-sets = <64>;
> > > +                     i-cache-size = <32768>;
> > > +                     i-tlb-sets = <1>;
> > > +                     i-tlb-size = <32>;
> > > +                     mmu-type = "riscv,sv39";
> > > +                     reg = <1>;
> > > +                     riscv,isa = "rv64imafdc";
> > > +                     tlb-split;
> > > +                     status = "okay";
> > > +
> > > +                     cpu1_intc: interrupt-controller {
> > > +                             #interrupt-cells = <1>;
> > > +                             compatible = "riscv,cpu-intc";
> > > +                             interrupt-controller;
> > > +                     };
> > > +             };
> > > +
> > > +             cpu@2 {
> > > +                     clock-frequency = <0>;
> > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > +                     d-cache-block-size = <64>;
> > > +                     d-cache-sets = <64>;
> > > +                     d-cache-size = <32768>;
> > > +                     d-tlb-sets = <1>;
> > > +                     d-tlb-size = <32>;
> > > +                     device_type = "cpu";
> > > +                     i-cache-block-size = <64>;
> > > +                     i-cache-sets = <64>;
> > > +                     i-cache-size = <32768>;
> > > +                     i-tlb-sets = <1>;
> > > +                     i-tlb-size = <32>;
> > > +                     mmu-type = "riscv,sv39";
> > > +                     reg = <2>;
> > > +                     riscv,isa = "rv64imafdc";
> > > +                     tlb-split;
> > > +                     status = "okay";
> > > +
> > > +                     cpu2_intc: interrupt-controller {
> > > +                             #interrupt-cells = <1>;
> > > +                             compatible = "riscv,cpu-intc";
> > > +                             interrupt-controller;
> > > +                     };
> > > +             };
> > > +
> > > +             cpu@3 {
> > > +                     clock-frequency = <0>;
> > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > +                     d-cache-block-size = <64>;
> > > +                     d-cache-sets = <64>;
> > > +                     d-cache-size = <32768>;
> > > +                     d-tlb-sets = <1>;
> > > +                     d-tlb-size = <32>;
> > > +                     device_type = "cpu";
> > > +                     i-cache-block-size = <64>;
> > > +                     i-cache-sets = <64>;
> > > +                     i-cache-size = <32768>;
> > > +                     i-tlb-sets = <1>;
> > > +                     i-tlb-size = <32>;
> > > +                     mmu-type = "riscv,sv39";
> > > +                     reg = <3>;
> > > +                     riscv,isa = "rv64imafdc";
> > > +                     tlb-split;
> > > +                     status = "okay";
> > > +
> > > +                     cpu3_intc: interrupt-controller {
> > > +                             #interrupt-cells = <1>;
> > > +                             compatible = "riscv,cpu-intc";
> > > +                             interrupt-controller;
> > > +                     };
> > > +             };
> > > +
> > > +             cpu@4 {
> > > +                     clock-frequency = <0>;
> > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > +                     d-cache-block-size = <64>;
> > > +                     d-cache-sets = <64>;
> > > +                     d-cache-size = <32768>;
> > > +                     d-tlb-sets = <1>;
> > > +                     d-tlb-size = <32>;
> > > +                     device_type = "cpu";
> > > +                     i-cache-block-size = <64>;
> > > +                     i-cache-sets = <64>;
> > > +                     i-cache-size = <32768>;
> > > +                     i-tlb-sets = <1>;
> > > +                     i-tlb-size = <32>;
> > > +                     mmu-type = "riscv,sv39";
> > > +                     reg = <4>;
> > > +                     riscv,isa = "rv64imafdc";
> > > +                     tlb-split;
> > > +                     status = "okay";
> > > +                     cpu4_intc: interrupt-controller {
> > > +                             #interrupt-cells = <1>;
> > > +                             compatible = "riscv,cpu-intc";
> > > +                             interrupt-controller;
> > > +                     };
> > > +             };
> > > +     };
> > > +
> > > +     soc {
> > > +             #address-cells = <2>;
> > > +             #size-cells = <2>;
> > > +             compatible = "simple-bus";
> > > +             ranges;
> > > +
> > > +             cache-controller@2010000 {
> > > +                     compatible = "sifive,fu540-c000-ccache", "cache";
> > > +                     cache-block-size = <64>;
> > > +                     cache-level = <2>;
> > > +                     cache-sets = <1024>;
> > > +                     cache-size = <2097152>;
> > > +                     cache-unified;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <1 2 3>;
> > > +                     reg = <0x0 0x2010000 0x0 0x1000>;
> > > +             };
> > > +
> > > +             clint@2000000 {
> > > +                     compatible = "sifive,clint0";
> > > +                     reg = <0x0 0x2000000 0x0 0xC000>;
> > > +                     interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> > > +                                             &cpu1_intc 3 &cpu1_intc 7
> > > +                                             &cpu2_intc 3 &cpu2_intc 7
> > > +                                             &cpu3_intc 3 &cpu3_intc 7
> > > +                                             &cpu4_intc 3 &cpu4_intc 7>;
> > > +             };
> > > +
> > > +             plic: interrupt-controller@c000000 {
> > > +                     #interrupt-cells = <1>;
> > > +                     compatible = "sifive,plic-1.0.0";
> > > +                     reg = <0x0 0xc000000 0x0 0x4000000>;
> > > +                     riscv,ndev = <186>;
> > > +                     interrupt-controller;
> > > +                     interrupts-extended = <&cpu0_intc 11
> > > +                                     &cpu1_intc 11 &cpu1_intc 9
> > > +                                     &cpu2_intc 11 &cpu2_intc 9
> > > +                                     &cpu3_intc 11 &cpu3_intc 9
> > > +                                     &cpu4_intc 11 &cpu4_intc 9>;
> > > +             };
> > > +
> > > +             dma@3000000 {
> > > +                     compatible = "sifive,fu540-c000-pdma";
> > > +                     reg = <0x0 0x3000000 0x0 0x8000>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <23 24 25 26 27 28 29 30>;
> > > +                     #dma-cells = <1>;
> > > +             };
> > > +
> > > +             refclk: refclk {
> > > +                     compatible = "fixed-clock";
> > > +                     #clock-cells = <0>;
> > > +                     clock-frequency = <600000000>;
> > > +                     clock-output-names = "msspllclk";
> > > +             };
> > > +
> > > +             clkcfg: clkcfg@20002000 {
> > > +                     compatible = "microchip,mpfs-clkcfg";
> > > +                     reg = <0x0 0x20002000 0x0 0x1000>;
> > > +                     reg-names = "mss_sysreg";
> > > +                     clocks = <&refclk>;
> > > +                     #clock-cells = <1>;
> > > +                     clock-output-names = "cpu", "axi", "ahb", "envm",       /* 0-3   */
> > > +                              "mac0", "mac1", "mmc", "timer",                /* 4-7   */
> > > +                             "mmuart0", "mmuart1", "mmuart2", "mmuart3",     /* 8-11  */
> > > +                             "mmuart4", "spi0", "spi1", "i2c0",              /* 12-15 */
> > > +                             "i2c1", "can0", "can1", "usb",                  /* 16-19 */
> > > +                             "rsvd", "rtc", "qspi", "gpio0",                 /* 20-23 */
> > > +                             "gpio1", "gpio2", "ddrc", "fic0",               /* 24-27 */
> > > +                             "fic1", "fic2", "fic3", "athena", "cfm";        /* 28-32 */
> > > +             };
> > > +
> > > +             serial0: serial@20000000 {
> > > +                     compatible = "ns16550a";
> > > +                     reg = <0x0 0x20000000 0x0 0x400>;
> > > +                     reg-io-width = <4>;
> > > +                     reg-shift = <2>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <90>;
> > > +                     current-speed = <115200>;
> > > +                     clocks = <&clkcfg 8>;
> > > +                     status = "disabled";
> > > +             };
> > > +
> > > +             serial1: serial@20100000 {
> > > +                     compatible = "ns16550a";
> > > +                     reg = <0x0 0x20100000 0x0 0x400>;
> > > +                     reg-io-width = <4>;
> > > +                     reg-shift = <2>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <91>;
> > > +                     current-speed = <115200>;
> > > +                     clocks = <&clkcfg 9>;
> > > +                     status = "disabled";
> > > +             };
> > > +
> > > +             serial2: serial@20102000 {
> > > +                     compatible = "ns16550a";
> > > +                     reg = <0x0 0x20102000 0x0 0x400>;
> > > +                     reg-io-width = <4>;
> > > +                     reg-shift = <2>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <92>;
> > > +                     current-speed = <115200>;
> > > +                     clocks = <&clkcfg 10>;
> > > +                     status = "disabled";
> > > +             };
> > > +
> > > +             serial3: serial@20104000 {
> > > +                     compatible = "ns16550a";
> > > +                     reg = <0x0 0x20104000 0x0 0x400>;
> > > +                     reg-io-width = <4>;
> > > +                     reg-shift = <2>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <93>;
> > > +                     current-speed = <115200>;
> > > +                     clocks = <&clkcfg 11>;
> > > +                     status = "disabled";
> > > +             };
> > > +
> > > +             emmc: mmc@20008000 {
> > > +                     compatible = "cdns,sd4hc";
> > > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <88 89>;
> > > +                     pinctrl-names = "default";
> > > +                     clocks = <&clkcfg 6>;
> > > +                     bus-width = <4>;
> > > +                     cap-mmc-highspeed;
> > > +                     mmc-ddr-3_3v;
> > > +                     max-frequency = <200000000>;
> > > +                     non-removable;
> > > +                     no-sd;
> > > +                     no-sdio;
> > > +                     voltage-ranges = <3300 3300>;
> > > +                     status = "disabled";
> > > +             };
> > > +
> > > +             sdcard: sdhc@20008000 {
> > > +                     compatible = "cdns,sd4hc";
> > > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <88>;
> > > +                     pinctrl-names = "default";
> > > +                     clocks = <&clkcfg 6>;
> > > +                     bus-width = <4>;
> > > +                     disable-wp;
> > > +                     cap-sd-highspeed;
> > > +                     card-detect-delay = <200>;
> > > +                     sd-uhs-sdr12;
> > > +                     sd-uhs-sdr25;
> > > +                     sd-uhs-sdr50;
> > > +                     sd-uhs-sdr104;
> > > +                     max-frequency = <200000000>;
> > > +                     status = "disabled";
> > > +             };
> > > +
> > > +             emac0: ethernet@20110000 {
> > > +                     compatible = "cdns,macb";
> > > +                     reg = <0x0 0x20110000 0x0 0x2000>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <64 65 66 67>;
> > > +                     local-mac-address = [00 00 00 00 00 00];
> > > +                     clocks = <&clkcfg 4>, <&clkcfg 2>;
> > > +                     clock-names = "pclk", "hclk";
> > > +                     status = "disabled";
> > > +                     #address-cells = <1>;
> > > +                     #size-cells = <0>;
> > > +             };
> > > +
> > > +             emac1: ethernet@20112000 {
> > > +                     compatible = "cdns,macb";
> > > +                     reg = <0x0 0x20112000 0x0 0x2000>;
> > > +                     interrupt-parent = <&plic>;
> > > +                     interrupts = <70 71 72 73>;
> > > +                     mac-address = [00 00 00 00 00 00];
> > > +                     clocks = <&clkcfg 5>, <&clkcfg 2>;
> > > +                     status = "disabled";
> > > +                     clock-names = "pclk", "hclk";
> > > +                     #address-cells = <1>;
> > > +                     #size-cells = <0>;
> > > +             };
> > > +
> > > +     };
> > > +};
> > >
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>
> _______________________________________________
> linux-riscv mailing list
> linux-riscv@lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-riscv



-- 
Regards,
Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-04-18  3:36       ` Atish Patra
@ 2021-04-18  4:24         ` Atish Patra
  2021-04-18 18:39         ` Vitaly Wool
  1 sibling, 0 replies; 21+ messages in thread
From: Atish Patra @ 2021-04-18  4:24 UTC (permalink / raw)
  To: Vitaly Wool
  Cc: Alex Ghiti, Atish Patra, LKML, Albert Ou, Alistair Francis,
	Anup Patel, Björn Töpel, devicetree, linux-riscv,
	Palmer Dabbelt, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

On Sat, Apr 17, 2021 at 8:36 PM Atish Patra <atishp@atishpatra.org> wrote:
>
> On Mon, Mar 29, 2021 at 10:04 AM Vitaly Wool <vitaly.wool@konsulko.com> wrote:
> >
> > On Sat, Mar 27, 2021 at 6:24 PM Alex Ghiti <alex@ghiti.fr> wrote:
> > >
> > > Hi Atish,
> > >
> > > Le 3/3/21 à 3:02 PM, Atish Patra a écrit :
> > > > Add initial DTS for Microchip ICICLE board having only
> > > > essential devices (clocks, sdhci, ethernet, serial, etc).
> > > > The device tree is based on the U-Boot patch.
> > > >
> > > > https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> > > >
> > > > Signed-off-by: Atish Patra <atish.patra@wdc.com>
> > > > ---
> > > >   arch/riscv/boot/dts/Makefile                  |   1 +
> > > >   arch/riscv/boot/dts/microchip/Makefile        |   2 +
> > > >   .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> > > >   .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> > > >   4 files changed, 404 insertions(+)
> > > >   create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> > > >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > >
> > > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> > > > index 7ffd502e3e7b..fe996b88319e 100644
> > > > --- a/arch/riscv/boot/dts/Makefile
> > > > +++ b/arch/riscv/boot/dts/Makefile
> > > > @@ -1,5 +1,6 @@
> > > >   # SPDX-License-Identifier: GPL-2.0
> > > >   subdir-y += sifive
> > > >   subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > > > +subdir-y += microchip
> > > >
> > > >   obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> > > > diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> > > > new file mode 100644
> > > > index 000000000000..622b12771fd3
> > > > --- /dev/null
> > > > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > > > @@ -0,0 +1,2 @@
> > > > +# SPDX-License-Identifier: GPL-2.0
> > > > +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> > >
> > > I'm playing (or trying to...) with XIP_KERNEL and I had to add the
> > > following to have the device tree actually builtin the kernel:
> > >
> > > diff --git a/arch/riscv/boot/dts/microchip/Makefile
> > > b/arch/riscv/boot/dts/microchip/Makefile
> > > index 622b12771fd3..855c1502d912 100644
> > > --- a/arch/riscv/boot/dts/microchip/Makefile
> > > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > > @@ -1,2 +1,3 @@
> > >   # SPDX-License-Identifier: GPL-2.0
> > >   dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> > > +obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
> > >
> > > Alex
> >
> > Yes, I believe this is necessary for BUILTIN_DTB to work on Polarfire,
> > regardless of whether the kernel is XIP or not.
> >
>
> But there is no usecase for BUILTIN_DTB for polarfire except XIP kernel.
> The bootloaders for polarfire is capable of providing a DTB to kernel.
>
> If XIP kernel is enabled, the following line in
> arch/riscv/boot/dts/Makefile should take care of things
>
(Sorry. The mail was sent by mistake earlier with incomplete response)
Otherwise, we need a similar change for unleashed as well. No ?

>
> > Best regards,
> >    Vitaly
> >
> > > > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > > new file mode 100644
> > > > index 000000000000..ec79944065c9
> > > > --- /dev/null
> > > > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > > @@ -0,0 +1,72 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/* Copyright (c) 2020 Microchip Technology Inc */
> > > > +
> > > > +/dts-v1/;
> > > > +
> > > > +#include "microchip-mpfs.dtsi"
> > > > +
> > > > +/* Clock frequency (in Hz) of the rtcclk */
> > > > +#define RTCCLK_FREQ          1000000
> > > > +
> > > > +/ {
> > > > +     #address-cells = <2>;
> > > > +     #size-cells = <2>;
> > > > +     model = "Microchip PolarFire-SoC Icicle Kit";
> > > > +     compatible = "microchip,mpfs-icicle-kit";
> > > > +
> > > > +     chosen {
> > > > +             stdout-path = &serial0;
> > > > +     };
> > > > +
> > > > +     cpus {
> > > > +             timebase-frequency = <RTCCLK_FREQ>;
> > > > +     };
> > > > +
> > > > +     memory@80000000 {
> > > > +             device_type = "memory";
> > > > +             reg = <0x0 0x80000000 0x0 0x40000000>;
> > > > +             clocks = <&clkcfg 26>;
> > > > +     };
> > > > +
> > > > +     soc {
> > > > +     };
> > > > +};
> > > > +
> > > > +&serial0 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&serial1 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&serial2 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&serial3 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&sdcard {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&emac0 {
> > > > +     phy-mode = "sgmii";
> > > > +     phy-handle = <&phy0>;
> > > > +     phy0: ethernet-phy@8 {
> > > > +             reg = <8>;
> > > > +             ti,fifo-depth = <0x01>;
> > > > +     };
> > > > +};
> > > > +
> > > > +&emac1 {
> > > > +     status = "okay";
> > > > +     phy-mode = "sgmii";
> > > > +     phy-handle = <&phy1>;
> > > > +     phy1: ethernet-phy@9 {
> > > > +             reg = <9>;
> > > > +             ti,fifo-depth = <0x01>;
> > > > +     };
> > > > +};
> > > > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > > new file mode 100644
> > > > index 000000000000..b9819570a7d1
> > > > --- /dev/null
> > > > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > > @@ -0,0 +1,329 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/* Copyright (c) 2020 Microchip Technology Inc */
> > > > +
> > > > +/dts-v1/;
> > > > +
> > > > +/ {
> > > > +     #address-cells = <2>;
> > > > +     #size-cells = <2>;
> > > > +     model = "Microchip MPFS Icicle Kit";
> > > > +     compatible = "microchip,mpfs-icicle-kit";
> > > > +
> > > > +     chosen {
> > > > +     };
> > > > +
> > > > +     cpus {
> > > > +             #address-cells = <1>;
> > > > +             #size-cells = <0>;
> > > > +
> > > > +             cpu@0 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,e51", "sifive,rocket0", "riscv";
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <128>;
> > > > +                     i-cache-size = <16384>;
> > > > +                     reg = <0>;
> > > > +                     riscv,isa = "rv64imac";
> > > > +                     status = "disabled";
> > > > +
> > > > +                     cpu0_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@1 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <1>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +
> > > > +                     cpu1_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@2 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <2>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +
> > > > +                     cpu2_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@3 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <3>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +
> > > > +                     cpu3_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@4 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <4>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +                     cpu4_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +     };
> > > > +
> > > > +     soc {
> > > > +             #address-cells = <2>;
> > > > +             #size-cells = <2>;
> > > > +             compatible = "simple-bus";
> > > > +             ranges;
> > > > +
> > > > +             cache-controller@2010000 {
> > > > +                     compatible = "sifive,fu540-c000-ccache", "cache";
> > > > +                     cache-block-size = <64>;
> > > > +                     cache-level = <2>;
> > > > +                     cache-sets = <1024>;
> > > > +                     cache-size = <2097152>;
> > > > +                     cache-unified;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <1 2 3>;
> > > > +                     reg = <0x0 0x2010000 0x0 0x1000>;
> > > > +             };
> > > > +
> > > > +             clint@2000000 {
> > > > +                     compatible = "sifive,clint0";
> > > > +                     reg = <0x0 0x2000000 0x0 0xC000>;
> > > > +                     interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> > > > +                                             &cpu1_intc 3 &cpu1_intc 7
> > > > +                                             &cpu2_intc 3 &cpu2_intc 7
> > > > +                                             &cpu3_intc 3 &cpu3_intc 7
> > > > +                                             &cpu4_intc 3 &cpu4_intc 7>;
> > > > +             };
> > > > +
> > > > +             plic: interrupt-controller@c000000 {
> > > > +                     #interrupt-cells = <1>;
> > > > +                     compatible = "sifive,plic-1.0.0";
> > > > +                     reg = <0x0 0xc000000 0x0 0x4000000>;
> > > > +                     riscv,ndev = <186>;
> > > > +                     interrupt-controller;
> > > > +                     interrupts-extended = <&cpu0_intc 11
> > > > +                                     &cpu1_intc 11 &cpu1_intc 9
> > > > +                                     &cpu2_intc 11 &cpu2_intc 9
> > > > +                                     &cpu3_intc 11 &cpu3_intc 9
> > > > +                                     &cpu4_intc 11 &cpu4_intc 9>;
> > > > +             };
> > > > +
> > > > +             dma@3000000 {
> > > > +                     compatible = "sifive,fu540-c000-pdma";
> > > > +                     reg = <0x0 0x3000000 0x0 0x8000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <23 24 25 26 27 28 29 30>;
> > > > +                     #dma-cells = <1>;
> > > > +             };
> > > > +
> > > > +             refclk: refclk {
> > > > +                     compatible = "fixed-clock";
> > > > +                     #clock-cells = <0>;
> > > > +                     clock-frequency = <600000000>;
> > > > +                     clock-output-names = "msspllclk";
> > > > +             };
> > > > +
> > > > +             clkcfg: clkcfg@20002000 {
> > > > +                     compatible = "microchip,mpfs-clkcfg";
> > > > +                     reg = <0x0 0x20002000 0x0 0x1000>;
> > > > +                     reg-names = "mss_sysreg";
> > > > +                     clocks = <&refclk>;
> > > > +                     #clock-cells = <1>;
> > > > +                     clock-output-names = "cpu", "axi", "ahb", "envm",       /* 0-3   */
> > > > +                              "mac0", "mac1", "mmc", "timer",                /* 4-7   */
> > > > +                             "mmuart0", "mmuart1", "mmuart2", "mmuart3",     /* 8-11  */
> > > > +                             "mmuart4", "spi0", "spi1", "i2c0",              /* 12-15 */
> > > > +                             "i2c1", "can0", "can1", "usb",                  /* 16-19 */
> > > > +                             "rsvd", "rtc", "qspi", "gpio0",                 /* 20-23 */
> > > > +                             "gpio1", "gpio2", "ddrc", "fic0",               /* 24-27 */
> > > > +                             "fic1", "fic2", "fic3", "athena", "cfm";        /* 28-32 */
> > > > +             };
> > > > +
> > > > +             serial0: serial@20000000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20000000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <90>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 8>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             serial1: serial@20100000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20100000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <91>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 9>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             serial2: serial@20102000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20102000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <92>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 10>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             serial3: serial@20104000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20104000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <93>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 11>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             emmc: mmc@20008000 {
> > > > +                     compatible = "cdns,sd4hc";
> > > > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <88 89>;
> > > > +                     pinctrl-names = "default";
> > > > +                     clocks = <&clkcfg 6>;
> > > > +                     bus-width = <4>;
> > > > +                     cap-mmc-highspeed;
> > > > +                     mmc-ddr-3_3v;
> > > > +                     max-frequency = <200000000>;
> > > > +                     non-removable;
> > > > +                     no-sd;
> > > > +                     no-sdio;
> > > > +                     voltage-ranges = <3300 3300>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             sdcard: sdhc@20008000 {
> > > > +                     compatible = "cdns,sd4hc";
> > > > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <88>;
> > > > +                     pinctrl-names = "default";
> > > > +                     clocks = <&clkcfg 6>;
> > > > +                     bus-width = <4>;
> > > > +                     disable-wp;
> > > > +                     cap-sd-highspeed;
> > > > +                     card-detect-delay = <200>;
> > > > +                     sd-uhs-sdr12;
> > > > +                     sd-uhs-sdr25;
> > > > +                     sd-uhs-sdr50;
> > > > +                     sd-uhs-sdr104;
> > > > +                     max-frequency = <200000000>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             emac0: ethernet@20110000 {
> > > > +                     compatible = "cdns,macb";
> > > > +                     reg = <0x0 0x20110000 0x0 0x2000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <64 65 66 67>;
> > > > +                     local-mac-address = [00 00 00 00 00 00];
> > > > +                     clocks = <&clkcfg 4>, <&clkcfg 2>;
> > > > +                     clock-names = "pclk", "hclk";
> > > > +                     status = "disabled";
> > > > +                     #address-cells = <1>;
> > > > +                     #size-cells = <0>;
> > > > +             };
> > > > +
> > > > +             emac1: ethernet@20112000 {
> > > > +                     compatible = "cdns,macb";
> > > > +                     reg = <0x0 0x20112000 0x0 0x2000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <70 71 72 73>;
> > > > +                     mac-address = [00 00 00 00 00 00];
> > > > +                     clocks = <&clkcfg 5>, <&clkcfg 2>;
> > > > +                     status = "disabled";
> > > > +                     clock-names = "pclk", "hclk";
> > > > +                     #address-cells = <1>;
> > > > +                     #size-cells = <0>;
> > > > +             };
> > > > +
> > > > +     };
> > > > +};
> > > >
> > >
> > > _______________________________________________
> > > linux-riscv mailing list
> > > linux-riscv@lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-riscv
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>
>
>
> --
> Regards,
> Atish



-- 
Regards,
Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board
  2021-04-18  3:36       ` Atish Patra
  2021-04-18  4:24         ` Atish Patra
@ 2021-04-18 18:39         ` Vitaly Wool
  1 sibling, 0 replies; 21+ messages in thread
From: Vitaly Wool @ 2021-04-18 18:39 UTC (permalink / raw)
  To: Atish Patra
  Cc: Alex Ghiti, Atish Patra, LKML, Albert Ou, Alistair Francis,
	Anup Patel, Björn Töpel, devicetree, linux-riscv,
	Palmer Dabbelt, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

Hi Atish,

On Sun, Apr 18, 2021 at 5:37 AM Atish Patra <atishp@atishpatra.org> wrote:
>
> On Mon, Mar 29, 2021 at 10:04 AM Vitaly Wool <vitaly.wool@konsulko.com> wrote:
> >
> > On Sat, Mar 27, 2021 at 6:24 PM Alex Ghiti <alex@ghiti.fr> wrote:
> > >
> > > Hi Atish,
> > >
> > > Le 3/3/21 à 3:02 PM, Atish Patra a écrit :
> > > > Add initial DTS for Microchip ICICLE board having only
> > > > essential devices (clocks, sdhci, ethernet, serial, etc).
> > > > The device tree is based on the U-Boot patch.
> > > >
> > > > https://patchwork.ozlabs.org/project/uboot/patch/20201110103414.10142-6-padmarao.begari@microchip.com/
> > > >
> > > > Signed-off-by: Atish Patra <atish.patra@wdc.com>
> > > > ---
> > > >   arch/riscv/boot/dts/Makefile                  |   1 +
> > > >   arch/riscv/boot/dts/microchip/Makefile        |   2 +
> > > >   .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> > > >   .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> > > >   4 files changed, 404 insertions(+)
> > > >   create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> > > >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > >   create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > >
> > > > diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
> > > > index 7ffd502e3e7b..fe996b88319e 100644
> > > > --- a/arch/riscv/boot/dts/Makefile
> > > > +++ b/arch/riscv/boot/dts/Makefile
> > > > @@ -1,5 +1,6 @@
> > > >   # SPDX-License-Identifier: GPL-2.0
> > > >   subdir-y += sifive
> > > >   subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
> > > > +subdir-y += microchip
> > > >
> > > >   obj-$(CONFIG_BUILTIN_DTB) := $(addsuffix /, $(subdir-y))
> > > > diff --git a/arch/riscv/boot/dts/microchip/Makefile b/arch/riscv/boot/dts/microchip/Makefile
> > > > new file mode 100644
> > > > index 000000000000..622b12771fd3
> > > > --- /dev/null
> > > > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > > > @@ -0,0 +1,2 @@
> > > > +# SPDX-License-Identifier: GPL-2.0
> > > > +dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> > >
> > > I'm playing (or trying to...) with XIP_KERNEL and I had to add the
> > > following to have the device tree actually builtin the kernel:
> > >
> > > diff --git a/arch/riscv/boot/dts/microchip/Makefile
> > > b/arch/riscv/boot/dts/microchip/Makefile
> > > index 622b12771fd3..855c1502d912 100644
> > > --- a/arch/riscv/boot/dts/microchip/Makefile
> > > +++ b/arch/riscv/boot/dts/microchip/Makefile
> > > @@ -1,2 +1,3 @@
> > >   # SPDX-License-Identifier: GPL-2.0
> > >   dtb-$(CONFIG_SOC_MICROCHIP_POLARFIRE) += microchip-mpfs-icicle-kit.dtb
> > > +obj-$(CONFIG_BUILTIN_DTB) += $(addsuffix .o, $(dtb-y))
> > >
> > > Alex
> >
> > Yes, I believe this is necessary for BUILTIN_DTB to work on Polarfire,
> > regardless of whether the kernel is XIP or not.
> >
>
> But there is no usecase for BUILTIN_DTB for polarfire except XIP kernel.
> The bootloaders for polarfire is capable of providing a DTB to kernel.

I have hard time seeing an industrial application with a bootloader
mounting a vfat partition to load a device tree file. So there has to
be a less obscure and less time consuming alternative. And if the
mainline kernel doesn't provide it (e. g. in the form of support for
BUILTIN_DTB) it opens up for error prone custom solutions from various
vendors. Is that really what we want?

Best regards,
   Vitaly

> If XIP kernel is enabled, the following line in
> arch/riscv/boot/dts/Makefile should take care of things
>
>
> > Best regards,
> >    Vitaly
> >
> > > > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > > new file mode 100644
> > > > index 000000000000..ec79944065c9
> > > > --- /dev/null
> > > > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > > @@ -0,0 +1,72 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/* Copyright (c) 2020 Microchip Technology Inc */
> > > > +
> > > > +/dts-v1/;
> > > > +
> > > > +#include "microchip-mpfs.dtsi"
> > > > +
> > > > +/* Clock frequency (in Hz) of the rtcclk */
> > > > +#define RTCCLK_FREQ          1000000
> > > > +
> > > > +/ {
> > > > +     #address-cells = <2>;
> > > > +     #size-cells = <2>;
> > > > +     model = "Microchip PolarFire-SoC Icicle Kit";
> > > > +     compatible = "microchip,mpfs-icicle-kit";
> > > > +
> > > > +     chosen {
> > > > +             stdout-path = &serial0;
> > > > +     };
> > > > +
> > > > +     cpus {
> > > > +             timebase-frequency = <RTCCLK_FREQ>;
> > > > +     };
> > > > +
> > > > +     memory@80000000 {
> > > > +             device_type = "memory";
> > > > +             reg = <0x0 0x80000000 0x0 0x40000000>;
> > > > +             clocks = <&clkcfg 26>;
> > > > +     };
> > > > +
> > > > +     soc {
> > > > +     };
> > > > +};
> > > > +
> > > > +&serial0 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&serial1 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&serial2 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&serial3 {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&sdcard {
> > > > +     status = "okay";
> > > > +};
> > > > +
> > > > +&emac0 {
> > > > +     phy-mode = "sgmii";
> > > > +     phy-handle = <&phy0>;
> > > > +     phy0: ethernet-phy@8 {
> > > > +             reg = <8>;
> > > > +             ti,fifo-depth = <0x01>;
> > > > +     };
> > > > +};
> > > > +
> > > > +&emac1 {
> > > > +     status = "okay";
> > > > +     phy-mode = "sgmii";
> > > > +     phy-handle = <&phy1>;
> > > > +     phy1: ethernet-phy@9 {
> > > > +             reg = <9>;
> > > > +             ti,fifo-depth = <0x01>;
> > > > +     };
> > > > +};
> > > > diff --git a/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > > new file mode 100644
> > > > index 000000000000..b9819570a7d1
> > > > --- /dev/null
> > > > +++ b/arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> > > > @@ -0,0 +1,329 @@
> > > > +// SPDX-License-Identifier: (GPL-2.0 OR MIT)
> > > > +/* Copyright (c) 2020 Microchip Technology Inc */
> > > > +
> > > > +/dts-v1/;
> > > > +
> > > > +/ {
> > > > +     #address-cells = <2>;
> > > > +     #size-cells = <2>;
> > > > +     model = "Microchip MPFS Icicle Kit";
> > > > +     compatible = "microchip,mpfs-icicle-kit";
> > > > +
> > > > +     chosen {
> > > > +     };
> > > > +
> > > > +     cpus {
> > > > +             #address-cells = <1>;
> > > > +             #size-cells = <0>;
> > > > +
> > > > +             cpu@0 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,e51", "sifive,rocket0", "riscv";
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <128>;
> > > > +                     i-cache-size = <16384>;
> > > > +                     reg = <0>;
> > > > +                     riscv,isa = "rv64imac";
> > > > +                     status = "disabled";
> > > > +
> > > > +                     cpu0_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@1 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <1>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +
> > > > +                     cpu1_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@2 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <2>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +
> > > > +                     cpu2_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@3 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <3>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +
> > > > +                     cpu3_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +
> > > > +             cpu@4 {
> > > > +                     clock-frequency = <0>;
> > > > +                     compatible = "sifive,u54-mc", "sifive,rocket0", "riscv";
> > > > +                     d-cache-block-size = <64>;
> > > > +                     d-cache-sets = <64>;
> > > > +                     d-cache-size = <32768>;
> > > > +                     d-tlb-sets = <1>;
> > > > +                     d-tlb-size = <32>;
> > > > +                     device_type = "cpu";
> > > > +                     i-cache-block-size = <64>;
> > > > +                     i-cache-sets = <64>;
> > > > +                     i-cache-size = <32768>;
> > > > +                     i-tlb-sets = <1>;
> > > > +                     i-tlb-size = <32>;
> > > > +                     mmu-type = "riscv,sv39";
> > > > +                     reg = <4>;
> > > > +                     riscv,isa = "rv64imafdc";
> > > > +                     tlb-split;
> > > > +                     status = "okay";
> > > > +                     cpu4_intc: interrupt-controller {
> > > > +                             #interrupt-cells = <1>;
> > > > +                             compatible = "riscv,cpu-intc";
> > > > +                             interrupt-controller;
> > > > +                     };
> > > > +             };
> > > > +     };
> > > > +
> > > > +     soc {
> > > > +             #address-cells = <2>;
> > > > +             #size-cells = <2>;
> > > > +             compatible = "simple-bus";
> > > > +             ranges;
> > > > +
> > > > +             cache-controller@2010000 {
> > > > +                     compatible = "sifive,fu540-c000-ccache", "cache";
> > > > +                     cache-block-size = <64>;
> > > > +                     cache-level = <2>;
> > > > +                     cache-sets = <1024>;
> > > > +                     cache-size = <2097152>;
> > > > +                     cache-unified;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <1 2 3>;
> > > > +                     reg = <0x0 0x2010000 0x0 0x1000>;
> > > > +             };
> > > > +
> > > > +             clint@2000000 {
> > > > +                     compatible = "sifive,clint0";
> > > > +                     reg = <0x0 0x2000000 0x0 0xC000>;
> > > > +                     interrupts-extended = <&cpu0_intc 3 &cpu0_intc 7
> > > > +                                             &cpu1_intc 3 &cpu1_intc 7
> > > > +                                             &cpu2_intc 3 &cpu2_intc 7
> > > > +                                             &cpu3_intc 3 &cpu3_intc 7
> > > > +                                             &cpu4_intc 3 &cpu4_intc 7>;
> > > > +             };
> > > > +
> > > > +             plic: interrupt-controller@c000000 {
> > > > +                     #interrupt-cells = <1>;
> > > > +                     compatible = "sifive,plic-1.0.0";
> > > > +                     reg = <0x0 0xc000000 0x0 0x4000000>;
> > > > +                     riscv,ndev = <186>;
> > > > +                     interrupt-controller;
> > > > +                     interrupts-extended = <&cpu0_intc 11
> > > > +                                     &cpu1_intc 11 &cpu1_intc 9
> > > > +                                     &cpu2_intc 11 &cpu2_intc 9
> > > > +                                     &cpu3_intc 11 &cpu3_intc 9
> > > > +                                     &cpu4_intc 11 &cpu4_intc 9>;
> > > > +             };
> > > > +
> > > > +             dma@3000000 {
> > > > +                     compatible = "sifive,fu540-c000-pdma";
> > > > +                     reg = <0x0 0x3000000 0x0 0x8000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <23 24 25 26 27 28 29 30>;
> > > > +                     #dma-cells = <1>;
> > > > +             };
> > > > +
> > > > +             refclk: refclk {
> > > > +                     compatible = "fixed-clock";
> > > > +                     #clock-cells = <0>;
> > > > +                     clock-frequency = <600000000>;
> > > > +                     clock-output-names = "msspllclk";
> > > > +             };
> > > > +
> > > > +             clkcfg: clkcfg@20002000 {
> > > > +                     compatible = "microchip,mpfs-clkcfg";
> > > > +                     reg = <0x0 0x20002000 0x0 0x1000>;
> > > > +                     reg-names = "mss_sysreg";
> > > > +                     clocks = <&refclk>;
> > > > +                     #clock-cells = <1>;
> > > > +                     clock-output-names = "cpu", "axi", "ahb", "envm",       /* 0-3   */
> > > > +                              "mac0", "mac1", "mmc", "timer",                /* 4-7   */
> > > > +                             "mmuart0", "mmuart1", "mmuart2", "mmuart3",     /* 8-11  */
> > > > +                             "mmuart4", "spi0", "spi1", "i2c0",              /* 12-15 */
> > > > +                             "i2c1", "can0", "can1", "usb",                  /* 16-19 */
> > > > +                             "rsvd", "rtc", "qspi", "gpio0",                 /* 20-23 */
> > > > +                             "gpio1", "gpio2", "ddrc", "fic0",               /* 24-27 */
> > > > +                             "fic1", "fic2", "fic3", "athena", "cfm";        /* 28-32 */
> > > > +             };
> > > > +
> > > > +             serial0: serial@20000000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20000000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <90>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 8>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             serial1: serial@20100000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20100000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <91>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 9>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             serial2: serial@20102000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20102000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <92>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 10>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             serial3: serial@20104000 {
> > > > +                     compatible = "ns16550a";
> > > > +                     reg = <0x0 0x20104000 0x0 0x400>;
> > > > +                     reg-io-width = <4>;
> > > > +                     reg-shift = <2>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <93>;
> > > > +                     current-speed = <115200>;
> > > > +                     clocks = <&clkcfg 11>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             emmc: mmc@20008000 {
> > > > +                     compatible = "cdns,sd4hc";
> > > > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <88 89>;
> > > > +                     pinctrl-names = "default";
> > > > +                     clocks = <&clkcfg 6>;
> > > > +                     bus-width = <4>;
> > > > +                     cap-mmc-highspeed;
> > > > +                     mmc-ddr-3_3v;
> > > > +                     max-frequency = <200000000>;
> > > > +                     non-removable;
> > > > +                     no-sd;
> > > > +                     no-sdio;
> > > > +                     voltage-ranges = <3300 3300>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             sdcard: sdhc@20008000 {
> > > > +                     compatible = "cdns,sd4hc";
> > > > +                     reg = <0x0 0x20008000 0x0 0x1000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <88>;
> > > > +                     pinctrl-names = "default";
> > > > +                     clocks = <&clkcfg 6>;
> > > > +                     bus-width = <4>;
> > > > +                     disable-wp;
> > > > +                     cap-sd-highspeed;
> > > > +                     card-detect-delay = <200>;
> > > > +                     sd-uhs-sdr12;
> > > > +                     sd-uhs-sdr25;
> > > > +                     sd-uhs-sdr50;
> > > > +                     sd-uhs-sdr104;
> > > > +                     max-frequency = <200000000>;
> > > > +                     status = "disabled";
> > > > +             };
> > > > +
> > > > +             emac0: ethernet@20110000 {
> > > > +                     compatible = "cdns,macb";
> > > > +                     reg = <0x0 0x20110000 0x0 0x2000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <64 65 66 67>;
> > > > +                     local-mac-address = [00 00 00 00 00 00];
> > > > +                     clocks = <&clkcfg 4>, <&clkcfg 2>;
> > > > +                     clock-names = "pclk", "hclk";
> > > > +                     status = "disabled";
> > > > +                     #address-cells = <1>;
> > > > +                     #size-cells = <0>;
> > > > +             };
> > > > +
> > > > +             emac1: ethernet@20112000 {
> > > > +                     compatible = "cdns,macb";
> > > > +                     reg = <0x0 0x20112000 0x0 0x2000>;
> > > > +                     interrupt-parent = <&plic>;
> > > > +                     interrupts = <70 71 72 73>;
> > > > +                     mac-address = [00 00 00 00 00 00];
> > > > +                     clocks = <&clkcfg 5>, <&clkcfg 2>;
> > > > +                     status = "disabled";
> > > > +                     clock-names = "pclk", "hclk";
> > > > +                     #address-cells = <1>;
> > > > +                     #size-cells = <0>;
> > > > +             };
> > > > +
> > > > +     };
> > > > +};
> > > >
> > >
> > > _______________________________________________
> > > linux-riscv mailing list
> > > linux-riscv@lists.infradead.org
> > > http://lists.infradead.org/mailman/listinfo/linux-riscv
> >
> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>
>
>
> --
> Regards,
> Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 0/5] Add Microchip PolarFire Soc Support
  2021-04-18  3:26   ` Atish Patra
@ 2021-04-22 22:33     ` Atish Patra
  2021-04-23  1:37       ` Palmer Dabbelt
  0 siblings, 1 reply; 21+ messages in thread
From: Atish Patra @ 2021-04-22 22:33 UTC (permalink / raw)
  To: Palmer Dabbelt
  Cc: Atish Patra, linux-kernel@vger.kernel.org List, Albert Ou,
	Alistair Francis, Anup Patel, Björn Töpel, devicetree,
	linux-riscv, Paul Walmsley, Rob Herring, Conor.Dooley,
	Daire McNamara, Ivan.Griffin, Lewis.Hanly

On Sat, Apr 17, 2021 at 8:26 PM Atish Patra <atishp@atishpatra.org> wrote:
>
> On Mon, Mar 29, 2021 at 9:17 PM Palmer Dabbelt <palmer@dabbelt.com> wrote:
> >
> > On Wed, 03 Mar 2021 12:02:48 PST (-0800), Atish Patra wrote:
> > > This series adds minimal support for Microchip Polar Fire Soc Icicle kit.
> > > It is rebased on v5.12-rc1 and depends on clock support.
> > > Only MMC and ethernet drivers are enabled via this series.
> > > The idea here is to add the foundational patches so that other drivers
> > > can be added to on top of this. The device tree may change based on
> > > feedback on bindings of individual driver support patches.
> > >
> > > This series has been tested on Qemu and Polar Fire Soc Icicle kit.
> > > It depends on the updated clock-series[2] and macb fix[3].
> > > The series is also tested by Lewis from Microchip.
> > >
> > > The series can also be found at.
> > > https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4
> > >
> > > [1] https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
> > > [2] https://www.spinics.net/lists/linux-clk/msg54579.html
> > >
> > > Changes from v3->v4:
> > > 1. Fixed few DT specific issues.
> > > 2. Rebased on top of new clock driver.
> > > 3. SD card functionality is verified.
> > >
> > > Changes from v2->v3:
> > > 1. Fixed a typo in dt binding.
> > > 2. Included MAINTAINERS entry for PolarFire SoC.
> > > 3. Improved the dts file by using lowercase clock names and keeping phy
> > >    details in board specific dts file.
> > >
> > > Changes from v1->v2:
> > > 1. Modified the DT to match the device tree in U-Boot.
> > > 2. Added both eMMC & SDcard entries in DT. However, SD card is only enabled
> > >    as it allows larger storage option for linux distros.
> > >
> > > Atish Patra (4):
> > > RISC-V: Add Microchip PolarFire SoC kconfig option
> > > dt-bindings: riscv: microchip: Add YAML documentation for the
> > > PolarFire SoC
> > > RISC-V: Initial DTS for Microchip ICICLE board
> > > RISC-V: Enable Microchip PolarFire ICICLE SoC
> > >
> > > Conor Dooley (1):
> > > MAINTAINERS: add microchip polarfire soc support
> > >
> > > .../devicetree/bindings/riscv/microchip.yaml  |  27 ++
> > > MAINTAINERS                                   |   8 +
> > > arch/riscv/Kconfig.socs                       |   7 +
> > > arch/riscv/boot/dts/Makefile                  |   1 +
> > > arch/riscv/boot/dts/microchip/Makefile        |   2 +
> > > .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
> > > .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
> > > arch/riscv/configs/defconfig                  |   4 +
> > > 8 files changed, 450 insertions(+)
> > > create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml
> > > create mode 100644 arch/riscv/boot/dts/microchip/Makefile
> > > create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
> > > create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
> >
> > I had this left in my inbox waiting for either some reviews to come in or a v2,
> > but I don't see any.  Did I miss something?
> >
> Sorry for the late reply. I am on vacation until May. I think I saw
> all the patches have already been reviewed.
> Let me know if it is not the case.
>
I cross checked and all the patches are reviewed-by.
@palmer: Is it possible to take this series for 5.13 MW ?

> > _______________________________________________
> > linux-riscv mailing list
> > linux-riscv@lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>
>
>
> --
> Regards,
> Atish



-- 
Regards,
Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 0/5] Add Microchip PolarFire Soc Support
  2021-04-22 22:33     ` Atish Patra
@ 2021-04-23  1:37       ` Palmer Dabbelt
  2021-04-23  8:44         ` Conor.Dooley
  0 siblings, 1 reply; 21+ messages in thread
From: Palmer Dabbelt @ 2021-04-23  1:37 UTC (permalink / raw)
  To: atishp
  Cc: Atish Patra, linux-kernel, aou, Alistair Francis, Anup Patel,
	bjorn, devicetree, linux-riscv, Paul Walmsley, robh+dt,
	Conor.Dooley, daire.mcnamara, Ivan.Griffin, Lewis.Hanly

On Thu, 22 Apr 2021 15:33:39 PDT (-0700), atishp@atishpatra.org wrote:
> On Sat, Apr 17, 2021 at 8:26 PM Atish Patra <atishp@atishpatra.org> wrote:
>>
>> On Mon, Mar 29, 2021 at 9:17 PM Palmer Dabbelt <palmer@dabbelt.com> wrote:
>> >
>> > On Wed, 03 Mar 2021 12:02:48 PST (-0800), Atish Patra wrote:
>> > > This series adds minimal support for Microchip Polar Fire Soc Icicle kit.
>> > > It is rebased on v5.12-rc1 and depends on clock support.
>> > > Only MMC and ethernet drivers are enabled via this series.
>> > > The idea here is to add the foundational patches so that other drivers
>> > > can be added to on top of this. The device tree may change based on
>> > > feedback on bindings of individual driver support patches.
>> > >
>> > > This series has been tested on Qemu and Polar Fire Soc Icicle kit.
>> > > It depends on the updated clock-series[2] and macb fix[3].
>> > > The series is also tested by Lewis from Microchip.
>> > >
>> > > The series can also be found at.
>> > > https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4
>> > >
>> > > [1] https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
>> > > [2] https://www.spinics.net/lists/linux-clk/msg54579.html
>> > >
>> > > Changes from v3->v4:
>> > > 1. Fixed few DT specific issues.
>> > > 2. Rebased on top of new clock driver.
>> > > 3. SD card functionality is verified.
>> > >
>> > > Changes from v2->v3:
>> > > 1. Fixed a typo in dt binding.
>> > > 2. Included MAINTAINERS entry for PolarFire SoC.
>> > > 3. Improved the dts file by using lowercase clock names and keeping phy
>> > >    details in board specific dts file.
>> > >
>> > > Changes from v1->v2:
>> > > 1. Modified the DT to match the device tree in U-Boot.
>> > > 2. Added both eMMC & SDcard entries in DT. However, SD card is only enabled
>> > >    as it allows larger storage option for linux distros.
>> > >
>> > > Atish Patra (4):
>> > > RISC-V: Add Microchip PolarFire SoC kconfig option
>> > > dt-bindings: riscv: microchip: Add YAML documentation for the
>> > > PolarFire SoC
>> > > RISC-V: Initial DTS for Microchip ICICLE board
>> > > RISC-V: Enable Microchip PolarFire ICICLE SoC
>> > >
>> > > Conor Dooley (1):
>> > > MAINTAINERS: add microchip polarfire soc support
>> > >
>> > > .../devicetree/bindings/riscv/microchip.yaml  |  27 ++
>> > > MAINTAINERS                                   |   8 +
>> > > arch/riscv/Kconfig.socs                       |   7 +
>> > > arch/riscv/boot/dts/Makefile                  |   1 +
>> > > arch/riscv/boot/dts/microchip/Makefile        |   2 +
>> > > .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
>> > > .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 ++++++++++++++++++
>> > > arch/riscv/configs/defconfig                  |   4 +
>> > > 8 files changed, 450 insertions(+)
>> > > create mode 100644 Documentation/devicetree/bindings/riscv/microchip.yaml
>> > > create mode 100644 arch/riscv/boot/dts/microchip/Makefile
>> > > create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
>> > > create mode 100644 arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
>> >
>> > I had this left in my inbox waiting for either some reviews to come in or a v2,
>> > but I don't see any.  Did I miss something?
>> >
>> Sorry for the late reply. I am on vacation until May. I think I saw
>> all the patches have already been reviewed.
>> Let me know if it is not the case.
>>
> I cross checked and all the patches are reviewed-by.
> @palmer: Is it possible to take this series for 5.13 MW ?

I still don't see any reviews for the mailbox driver, did it just get 
lost on the way to me?

>
>> > _______________________________________________
>> > linux-riscv mailing list
>> > linux-riscv@lists.infradead.org
>> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>>
>>
>>
>> --
>> Regards,
>> Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 0/5] Add Microchip PolarFire Soc Support
  2021-04-23  1:37       ` Palmer Dabbelt
@ 2021-04-23  8:44         ` Conor.Dooley
  0 siblings, 0 replies; 21+ messages in thread
From: Conor.Dooley @ 2021-04-23  8:44 UTC (permalink / raw)
  To: palmer, atishp
  Cc: Atish.Patra, linux-kernel, aou, Alistair.Francis, Anup.Patel,
	bjorn, devicetree, linux-riscv, paul.walmsley, robh+dt,
	Daire.McNamara, Ivan.Griffin, Lewis.Hanly

On 23/04/2021 02:37, Palmer Dabbelt wrote:
> EXTERNAL EMAIL: Do not click links or open attachments unless you know 
> the content is safe
>
> On Thu, 22 Apr 2021 15:33:39 PDT (-0700), atishp@atishpatra.org wrote:
>> On Sat, Apr 17, 2021 at 8:26 PM Atish Patra <atishp@atishpatra.org> 
>> wrote:
>>>
>>> On Mon, Mar 29, 2021 at 9:17 PM Palmer Dabbelt <palmer@dabbelt.com> 
>>> wrote:
>>> >
>>> > On Wed, 03 Mar 2021 12:02:48 PST (-0800), Atish Patra wrote:
>>> > > This series adds minimal support for Microchip Polar Fire Soc 
>>> Icicle kit.
>>> > > It is rebased on v5.12-rc1 and depends on clock support.
>>> > > Only MMC and ethernet drivers are enabled via this series.
>>> > > The idea here is to add the foundational patches so that other 
>>> drivers
>>> > > can be added to on top of this. The device tree may change based on
>>> > > feedback on bindings of individual driver support patches.
>>> > >
>>> > > This series has been tested on Qemu and Polar Fire Soc Icicle kit.
>>> > > It depends on the updated clock-series[2] and macb fix[3].
>>> > > The series is also tested by Lewis from Microchip.
>>> > >
>>> > > The series can also be found at.
>>> > > 
>>> https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4
>>> > >
>>> > > [1] 
>>> https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
>>> > > [2] https://www.spinics.net/lists/linux-clk/msg54579.html
>>> > >
>>> > > Changes from v3->v4:
>>> > > 1. Fixed few DT specific issues.
>>> > > 2. Rebased on top of new clock driver.
>>> > > 3. SD card functionality is verified.
>>> > >
>>> > > Changes from v2->v3:
>>> > > 1. Fixed a typo in dt binding.
>>> > > 2. Included MAINTAINERS entry for PolarFire SoC.
>>> > > 3. Improved the dts file by using lowercase clock names and 
>>> keeping phy
>>> > >    details in board specific dts file.
>>> > >
>>> > > Changes from v1->v2:
>>> > > 1. Modified the DT to match the device tree in U-Boot.
>>> > > 2. Added both eMMC & SDcard entries in DT. However, SD card is 
>>> only enabled
>>> > >    as it allows larger storage option for linux distros.
>>> > >
>>> > > Atish Patra (4):
>>> > > RISC-V: Add Microchip PolarFire SoC kconfig option
>>> > > dt-bindings: riscv: microchip: Add YAML documentation for the
>>> > > PolarFire SoC
>>> > > RISC-V: Initial DTS for Microchip ICICLE board
>>> > > RISC-V: Enable Microchip PolarFire ICICLE SoC
>>> > >
>>> > > Conor Dooley (1):
>>> > > MAINTAINERS: add microchip polarfire soc support
>>> > >
>>> > > .../devicetree/bindings/riscv/microchip.yaml  |  27 ++
>>> > > MAINTAINERS                                   |   8 +
>>> > > arch/riscv/Kconfig.socs                       |   7 +
>>> > > arch/riscv/boot/dts/Makefile                  |   1 +
>>> > > arch/riscv/boot/dts/microchip/Makefile        |   2 +
>>> > > .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
>>> > > .../boot/dts/microchip/microchip-mpfs.dtsi    | 329 
>>> ++++++++++++++++++
>>> > > arch/riscv/configs/defconfig                  |   4 +
>>> > > 8 files changed, 450 insertions(+)
>>> > > create mode 100644 
>>> Documentation/devicetree/bindings/riscv/microchip.yaml
>>> > > create mode 100644 arch/riscv/boot/dts/microchip/Makefile
>>> > > create mode 100644 
>>> arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
>>> > > create mode 100644 
>>> arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
>>> >
>>> > I had this left in my inbox waiting for either some reviews to 
>>> come in or a v2,
>>> > but I don't see any.  Did I miss something?
>>> >
>>> Sorry for the late reply. I am on vacation until May. I think I saw
>>> all the patches have already been reviewed.
>>> Let me know if it is not the case.
>>>
>> I cross checked and all the patches are reviewed-by.
>> @palmer: Is it possible to take this series for 5.13 MW ?
>
> I still don't see any reviews for the mailbox driver, did it just get
> lost on the way to me?

the mailbox driver has reviewed-by tags on two of the five patches (rob 
on the dt-binding entries).
v6 was set on the 23rd but hasn't got any attention on the other three 
patches yet
however that's not in this patch set, only depends on it

>
>>
>>> > _______________________________________________
>>> > linux-riscv mailing list
>>> > linux-riscv@lists.infradead.org
>>> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>>>
>>>
>>>
>>> -- 
>>> Regards,
>>> Atish


_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

* Re: [PATCH v4 0/5] Add Microchip PolarFire Soc Support
       [not found] <CAOnJCUL5tLzk73GJNVXMmJmBKo_kVcAQ7OYwpi9bjKgTbabhyg@mail.gmail.com>
@ 2021-04-23 19:56 ` Palmer Dabbelt
  0 siblings, 0 replies; 21+ messages in thread
From: Palmer Dabbelt @ 2021-04-23 19:56 UTC (permalink / raw)
  To: atishp
  Cc: Conor.Dooley, Alistair Francis, Anup Patel, Atish Patra,
	Daire.McNamara, Ivan.Griffin, Lewis.Hanly, aou, bjorn,
	devicetree, linux-kernel, linux-riscv, Paul Walmsley, robh+dt

On Fri, 23 Apr 2021 05:31:22 PDT (-0700), atishp@atishpatra.org wrote:
> On Fri, Apr 23, 2021 at 1:44 AM <Conor.Dooley@microchip.com> wrote:
>
>> On 23/04/2021 02:37, Palmer Dabbelt wrote:
>> > EXTERNAL EMAIL: Do not click links or open attachments unless you know
>> > the content is safe
>> >
>> > On Thu, 22 Apr 2021 15:33:39 PDT (-0700), atishp@atishpatra.org wrote:
>> >> On Sat, Apr 17, 2021 at 8:26 PM Atish Patra <atishp@atishpatra.org>
>> >> wrote:
>> >>>
>> >>> On Mon, Mar 29, 2021 at 9:17 PM Palmer Dabbelt <palmer@dabbelt.com>
>> >>> wrote:
>> >>> >
>> >>> > On Wed, 03 Mar 2021 12:02:48 PST (-0800), Atish Patra wrote:
>> >>> > > This series adds minimal support for Microchip Polar Fire Soc
>> >>> Icicle kit.
>> >>> > > It is rebased on v5.12-rc1 and depends on clock support.
>> >>> > > Only MMC and ethernet drivers are enabled via this series.
>> >>> > > The idea here is to add the foundational patches so that other
>> >>> drivers
>> >>> > > can be added to on top of this. The device tree may change based on
>> >>> > > feedback on bindings of individual driver support patches.
>> >>> > >
>> >>> > > This series has been tested on Qemu and Polar Fire Soc Icicle kit.
>> >>> > > It depends on the updated clock-series[2] and macb fix[3].
>> >>> > > The series is also tested by Lewis from Microchip.
>> >>> > >
>> >>> > > The series can also be found at.
>> >>> > >
>> >>> https://github.com/atishp04/linux/tree/polarfire_support_upstream_v4
>> >>> > >
>> >>> > > [1]
>> >>> https://lists.nongnu.org/archive/html/qemu-devel/2020-10/msg08582.html
>> >>> > > [2] https://www.spinics.net/lists/linux-clk/msg54579.html
>> >>> > >
>> >>> > > Changes from v3->v4:
>> >>> > > 1. Fixed few DT specific issues.
>> >>> > > 2. Rebased on top of new clock driver.
>> >>> > > 3. SD card functionality is verified.
>> >>> > >
>> >>> > > Changes from v2->v3:
>> >>> > > 1. Fixed a typo in dt binding.
>> >>> > > 2. Included MAINTAINERS entry for PolarFire SoC.
>> >>> > > 3. Improved the dts file by using lowercase clock names and
>> >>> keeping phy
>> >>> > >    details in board specific dts file.
>> >>> > >
>> >>> > > Changes from v1->v2:
>> >>> > > 1. Modified the DT to match the device tree in U-Boot.
>> >>> > > 2. Added both eMMC & SDcard entries in DT. However, SD card is
>> >>> only enabled
>> >>> > >    as it allows larger storage option for linux distros.
>> >>> > >
>> >>> > > Atish Patra (4):
>> >>> > > RISC-V: Add Microchip PolarFire SoC kconfig option
>> >>> > > dt-bindings: riscv: microchip: Add YAML documentation for the
>> >>> > > PolarFire SoC
>> >>> > > RISC-V: Initial DTS for Microchip ICICLE board
>> >>> > > RISC-V: Enable Microchip PolarFire ICICLE SoC
>> >>> > >
>> >>> > > Conor Dooley (1):
>> >>> > > MAINTAINERS: add microchip polarfire soc support
>> >>> > >
>> >>> > > .../devicetree/bindings/riscv/microchip.yaml  |  27 ++
>> >>> > > MAINTAINERS                                   |   8 +
>> >>> > > arch/riscv/Kconfig.socs                       |   7 +
>> >>> > > arch/riscv/boot/dts/Makefile                  |   1 +
>> >>> > > arch/riscv/boot/dts/microchip/Makefile        |   2 +
>> >>> > > .../microchip/microchip-mpfs-icicle-kit.dts   |  72 ++++
>> >>> > > .../boot/dts/microchip/microchip-mpfs.dtsi    | 329
>> >>> ++++++++++++++++++
>> >>> > > arch/riscv/configs/defconfig                  |   4 +
>> >>> > > 8 files changed, 450 insertions(+)
>> >>> > > create mode 100644
>> >>> Documentation/devicetree/bindings/riscv/microchip.yaml
>> >>> > > create mode 100644 arch/riscv/boot/dts/microchip/Makefile
>> >>> > > create mode 100644
>> >>> arch/riscv/boot/dts/microchip/microchip-mpfs-icicle-kit.dts
>> >>> > > create mode 100644
>> >>> arch/riscv/boot/dts/microchip/microchip-mpfs.dtsi
>> >>> >
>> >>> > I had this left in my inbox waiting for either some reviews to
>> >>> come in or a v2,
>> >>> > but I don't see any.  Did I miss something?
>> >>> >
>> >>> Sorry for the late reply. I am on vacation until May. I think I saw
>> >>> all the patches have already been reviewed.
>> >>> Let me know if it is not the case.
>> >>>
>> >> I cross checked and all the patches are reviewed-by.
>> >> @palmer: Is it possible to take this series for 5.13 MW ?
>> >
>> > I still don't see any reviews for the mailbox driver, did it just get
>> > lost on the way to me?
>>
>> the mailbox driver has reviewed-by tags on two of the five patches (rob
>> on the dt-binding entries).
>> v6 was set on the 23rd but hasn't got any attention on the other three
>> patches yet
>> however that's not in this patch set, only depends on it
>>
>
> Thanks Conor.
>
> @palmer: This series adds the basic soc support
> for polarfire SoC. With clock driver, we can now boot.
>
> Mailbox driver series provides additional features.  Were you looking for
> reviewed-by tags for the clock driver ?

Ah, sorry.  I get this one mixed up with "Add support for the PolarFire 
SoC system controller", which I also had in my inbox because I wanted to 
make sure it didn't get dropped.  I guess I just didn't read the whole 
title and dropped this v4 because I thought the v6 was a newer version 
of the same patch set.

This is now on for-next.

Thanks!

>
>
>
>> >
>> >>
>> >>> > _______________________________________________
>> >>> > linux-riscv mailing list
>> >>> > linux-riscv@lists.infradead.org
>> >>> > http://lists.infradead.org/mailman/listinfo/linux-riscv
>> >>>
>> >>>
>> >>>
>> >>> --
>> >>> Regards,
>> >>> Atish
>>
>>
>> --
> Regards,
> Atish

_______________________________________________
linux-riscv mailing list
linux-riscv@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-riscv

^ permalink raw reply	[flat|nested] 21+ messages in thread

end of thread, back to index

Thread overview: 21+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-03-03 20:02 [PATCH v4 0/5] Add Microchip PolarFire Soc Support Atish Patra
2021-03-03 20:02 ` [PATCH v4 1/5] RISC-V: Add Microchip PolarFire SoC kconfig option Atish Patra
2021-03-03 20:02 ` [PATCH v4 2/5] dt-bindings: riscv: microchip: Add YAML documentation for the PolarFire SoC Atish Patra
2021-03-08 20:11   ` Rob Herring
2021-03-03 20:02 ` [PATCH v4 3/5] RISC-V: Initial DTS for Microchip ICICLE board Atish Patra
2021-03-09 10:56   ` Ben Dooks
     [not found]     ` <DM6PR11MB3770E7FA8121AA91D9EDC4FEE5929@DM6PR11MB3770.namprd11.prod.outlook.com>
2021-03-09 19:34       ` Atish Patra
2021-03-22  6:04   ` Bin Meng
2021-03-27 17:22   ` Alex Ghiti
2021-03-28 15:22     ` Vitaly Wool
2021-04-18  3:36       ` Atish Patra
2021-04-18  4:24         ` Atish Patra
2021-04-18 18:39         ` Vitaly Wool
2021-03-03 20:02 ` [PATCH v4 4/5] RISC-V: Enable Microchip PolarFire ICICLE SoC Atish Patra
2021-03-03 20:02 ` [PATCH v4 5/5] MAINTAINERS: add microchip polarfire soc support Atish Patra
2021-03-30  4:17 ` [PATCH v4 0/5] Add Microchip PolarFire Soc Support Palmer Dabbelt
2021-04-18  3:26   ` Atish Patra
2021-04-22 22:33     ` Atish Patra
2021-04-23  1:37       ` Palmer Dabbelt
2021-04-23  8:44         ` Conor.Dooley
     [not found] <CAOnJCUL5tLzk73GJNVXMmJmBKo_kVcAQ7OYwpi9bjKgTbabhyg@mail.gmail.com>
2021-04-23 19:56 ` Palmer Dabbelt

Linux-RISC-V Archive on lore.kernel.org

Archives are clonable:
	git clone --mirror https://lore.kernel.org/linux-riscv/0 linux-riscv/git/0.git

	# If you have public-inbox 1.1+ installed, you may
	# initialize and index your mirror using the following commands:
	public-inbox-init -V2 linux-riscv linux-riscv/ https://lore.kernel.org/linux-riscv \
		linux-riscv@lists.infradead.org
	public-inbox-index linux-riscv

Example config snippet for mirrors

Newsgroup available over NNTP:
	nntp://nntp.lore.kernel.org/org.infradead.lists.linux-riscv


AGPL code for this site: git clone https://public-inbox.org/public-inbox.git