[PATCH 1/8] ARM: dts: imx6qdl: Correct interrupt flags in examples

[PATCH 1/8] ARM: dts: imx6qdl: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.
---
 arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw552x.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw553x.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw560x.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw5903.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw5904.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw5907.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw5910.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw5912.dtsi | 3 ++-
 arch/arm/boot/dts/imx6qdl-gw5913.dtsi | 3 ++-
 14 files changed, 28 insertions(+), 14 deletions(-)

diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
index 4d01c3300b97..3c04b5a4f3cb 100644
--- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -152,7 +153,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
index f6182a9d201c..736074f1c3ef 100644
--- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -217,7 +218,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
index a28e79463d0c..8072ed47c6bb 100644
--- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -210,7 +211,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
index 55f368e192c0..8c9bcdd39830 100644
--- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/sound/fsl-imx-audmux.h>
 
 / {
@@ -247,7 +248,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
index 1516e2b0bcde..e5d803d023c8 100644
--- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
@@ -48,6 +48,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/media/tda1997x.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/sound/fsl-imx-audmux.h>
 
 / {
@@ -219,7 +220,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
index 0da6e6f7482b..290a607fede9 100644
--- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -144,7 +145,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
index faf9a3ba61b2..c15b9cc63bf8 100644
--- a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
@@ -47,6 +47,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -180,7 +181,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
index f68f9dada5b0..093a219a77ae 100644
--- a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
@@ -47,6 +47,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -294,7 +295,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi b/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
index fbe6c32bd756..e1c8dd233cab 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
@@ -47,6 +47,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	chosen {
@@ -235,7 +236,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
index 23c6e4047621..3cd2e717c1da 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
@@ -47,6 +47,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -257,7 +258,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
index b1ff7c859c4d..21c68a55bcb9 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -154,7 +155,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
index 6c943a517ad7..ed4e22259959 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -163,7 +164,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
index 441d8ce97aa4..797f160249f7 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -158,7 +159,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#address-cells = <1>;
diff --git a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
index d62a8da49367..4cd7d290f5b2 100644
--- a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
+++ b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
@@ -5,6 +5,7 @@
 
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	/* these are used by bootloader for disabling nodes */
@@ -139,7 +140,7 @@
 		compatible = "gw,gsc";
 		reg = <0x20>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <4 GPIO_ACTIVE_LOW>;
+		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-controller;
 		#interrupt-cells = <1>;
 		#size-cells = <0>;
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 2/8] ARM: dts: rk3188: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags without affecting the code:
  ACTIVE_HIGH => IRQ_TYPE_NONE

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.
---
 arch/arm/boot/dts/rk3188-bqedison2qc.dts | 3 ++-
 1 file changed, 2 insertions(+), 1 deletion(-)

diff --git a/arch/arm/boot/dts/rk3188-bqedison2qc.dts b/arch/arm/boot/dts/rk3188-bqedison2qc.dts
index 66a0ff196eb1..b191347894f6 100644
--- a/arch/arm/boot/dts/rk3188-bqedison2qc.dts
+++ b/arch/arm/boot/dts/rk3188-bqedison2qc.dts
@@ -7,6 +7,7 @@
 /dts-v1/;
 #include <dt-bindings/i2c/i2c.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3188.dtsi"
 
 / {
@@ -479,7 +480,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio3>;
-		interrupts = <RK_PD2 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PD2 IRQ_TYPE_NONE>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 3/8] arm64: dts: imx8mm: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
  ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi      | 2 +-
 arch/arm64/boot/dts/freescale/imx8mm-evk.dts              | 2 +-
 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts | 2 +-
 arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi         | 2 +-
 4 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
index 620a124dfb5f..fdce665d7ac4 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
@@ -74,7 +74,7 @@
 		reg = <0x4b>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
index 38134d201eef..609d73e19fee 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
@@ -166,7 +166,7 @@
 		reg = <0x4b>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
index 0bca737964d5..b84d94e10c26 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
@@ -133,7 +133,7 @@
 		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_captouch>;
 		interrupt-parent = <&gpio5>;
-		interrupts = <4 GPIO_ACTIVE_HIGH>;
+		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
 
 		touchscreen-size-x = <800>;
 		touchscreen-size-y = <480>;
diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
index c371cb34b3f7..49743d2f60c1 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
@@ -137,7 +137,7 @@
 		reg = <0x4b>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio2>;
-		interrupts = <8 GPIO_ACTIVE_LOW>;
+		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 4/8] arm64: dts: imx8mn: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.
---
 arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts | 2 +-
 arch/arm64/boot/dts/freescale/imx8mn-evk.dts      | 3 ++-
 2 files changed, 3 insertions(+), 2 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
index a1e5483dbbbe..9e12b5234692 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-ddr4-evk.dts
@@ -55,7 +55,7 @@
 		reg = <0x4b>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		rohm,reset-snvs-powered;
 
 		regulators {
diff --git a/arch/arm64/boot/dts/freescale/imx8mn-evk.dts b/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
index b846526a8d8b..707d8486b4d8 100644
--- a/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mn-evk.dts
@@ -7,6 +7,7 @@
 
 #include "imx8mn.dtsi"
 #include "imx8mn-evk.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "NXP i.MX8MNano EVK board";
@@ -19,7 +20,7 @@
 		reg = <0x25>;
 		pinctrl-0 = <&pinctrl_pmic>;
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 
 		regulators {
 			buck1: BUCK1{
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 5/8] arm64: dts: imx8mq: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.
---
 arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts | 5 +++--
 arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi       | 3 ++-
 arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts       | 3 ++-
 arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts        | 3 ++-
 4 files changed, 9 insertions(+), 5 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
index a80e53428c2f..7f728dea32ca 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5-devkit.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/usb/pd.h"
 #include "imx8mq.dtsi"
@@ -60,7 +61,7 @@
 			label = "WWAN_WAKE";
 			gpios = <&gpio3 8 GPIO_ACTIVE_LOW>;
 			interrupt-parent = <&gpio3>;
-			interrupts = <8 GPIO_ACTIVE_LOW>;
+			interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
 			wakeup-source;
 			linux,code = <KEY_PHONE>;
 		};
@@ -288,7 +289,7 @@
 		#clock-cells = <0>;
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "irq";
 		rohm,reset-snvs-powered;
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
index c3e290703fe8..3c389c7ffb2c 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mq-librem5.dtsi
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/usb/pd.h"
 #include "imx8mq.dtsi"
@@ -639,7 +640,7 @@
 		clock-names = "osc";
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <7 GPIO_ACTIVE_LOW>;
+		interrupts = <7 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "irq";
 		rohm,reset-snvs-powered;
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts b/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
index 3f541ddf0768..05fcea2fb402 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-phanbell.dts
@@ -6,6 +6,7 @@
 /dts-v1/;
 
 #include "imx8mq.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "Google i.MX8MQ Phanbell";
@@ -125,7 +126,7 @@
 		clocks = <&pmic_osc>;
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 
 		regulators {
 			buck1: BUCK1 {
diff --git a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
index 59da96b7143f..84c3a143d87b 100644
--- a/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mq-pico-pi.dts
@@ -9,6 +9,7 @@
 /dts-v1/;
 
 #include "imx8mq.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	model = "TechNexion PICO-PI-8M";
@@ -70,7 +71,7 @@
 		clock-names = "osc";
 		clock-output-names = "pmic_clk";
 		interrupt-parent = <&gpio1>;
-		interrupts = <3 GPIO_ACTIVE_LOW>;
+		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
 		interrupt-names = "irq";
 
 		regulators {
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 6/8] arm64: dts: rk3399: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.
---
 arch/arm64/boot/dts/rockchip/rk3399-firefly.dts      | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts   | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts    | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts     | 3 ++-
 arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts   | 2 +-
 arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts   | 2 +-
 arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi     | 3 ++-
 8 files changed, 14 insertions(+), 8 deletions(-)

diff --git a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
index 6db18808b9c5..095d615950ca 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-firefly.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -676,7 +677,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
index 341d074ed996..25cb807bcfa6 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-hugsun-x99.dts
@@ -2,6 +2,7 @@
 /dts-v1/;
 #include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/input/input.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
 
@@ -623,7 +624,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
index e36837c04dc7..89dae74989bb 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-khadas-edge.dtsi
@@ -6,6 +6,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -662,7 +663,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		brcm,drive-strength = <5>;
 		pinctrl-names = "default";
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts b/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
index 1fa80ac15464..113a71256171 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-leez-p710.dts
@@ -5,6 +5,7 @@
 
 /dts-v1/;
 #include <dt-bindings/input/linux-event-codes.h>
+#include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/pwm/pwm.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
@@ -503,7 +504,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts b/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
index 6163ae8063a7..ae81fb9d363c 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-orangepi.dts
@@ -7,6 +7,7 @@
 
 #include "dt-bindings/pwm/pwm.h"
 #include "dt-bindings/input/input.h"
+#include <dt-bindings/interrupt-controller/irq.h>
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
 
@@ -691,7 +692,7 @@
 		reg = <1>;
 		compatible = "brcm,bcm4329-fmac";
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts
index f0055ce2fda0..7df4e698b1c0 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4b.dts
@@ -19,7 +19,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts
index 4c7ebb1c5d2d..887a29898617 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock-pi-4c.dts
@@ -20,7 +20,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
diff --git a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
index 5e3ac589bc54..9a4cd799edde 100644
--- a/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
+++ b/arch/arm64/boot/dts/rockchip/rk3399-rock960.dtsi
@@ -7,6 +7,7 @@
 
 #include "rk3399.dtsi"
 #include "rk3399-opp.dtsi"
+#include <dt-bindings/interrupt-controller/irq.h>
 
 / {
 	sdio_pwrseq: sdio-pwrseq {
@@ -522,7 +523,7 @@
 		compatible = "brcm,bcm4329-fmac";
 		reg = <1>;
 		interrupt-parent = <&gpio0>;
-		interrupts = <RK_PA3 GPIO_ACTIVE_HIGH>;
+		interrupts = <RK_PA3 IRQ_TYPE_LEVEL_HIGH>;
 		interrupt-names = "host-wake";
 		pinctrl-names = "default";
 		pinctrl-0 = <&wifi_host_wake_l>;
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 7/8] arm64: dts: zynqmp-zcu100-revC: Correct interrupt flags in examples

[Krzysztof Kozlowski]

GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
These are simple defines so they could be used in DTS but they will not
have the same meaning:
1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING

Correct the interrupt flags, assuming the author of the code wanted some
logical behavior behind the name "ACTIVE_xxx", this is:
  ACTIVE_LOW => IRQ_TYPE_LEVEL_LOW

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

---

Not tested on HW.
---
 arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
index d60110ad8367..c9460693f4e9 100644
--- a/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
+++ b/arch/arm64/boot/dts/xilinx/zynqmp-zcu100-revC.dts
@@ -186,7 +186,7 @@
 				compatible = "ti,tps65086";
 				reg = <0x5e>;
 				interrupt-parent = <&gpio>;
-				interrupts = <77 GPIO_ACTIVE_LOW>;
+				interrupts = <77 IRQ_TYPE_LEVEL_LOW>;
 				#gpio-cells = <2>;
 				gpio-controller;
 			};
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

[PATCH 8/8] arm64: dts: imx8mm-var-som-symphony: Drop unused gpioledgrp

[Krzysztof Kozlowski]

The gpioledgrp in iomux is not used, so it can be dropped.

Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
---
 arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts | 6 ------
 1 file changed, 6 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
index b84d94e10c26..fbf321cdcf16 100644
--- a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
@@ -193,12 +193,6 @@
 		>;
 	};
 
-	pinctrl_gpio_led: gpioledgrp {
-		fsl,pins = <
-			MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16	0x19
-		>;
-	};
-
 	pinctrl_i2c2: i2c2grp {
 		fsl,pins = <
 			MX8MM_IOMUXC_I2C2_SCL_I2C2_SCL		0x400001c3
-- 
2.17.1


_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 3/8] arm64: dts: imx8mm: Correct interrupt flags in examples

[Krzysztof Kozlowski]

On Tue, Sep 08, 2020 at 05:02:36PM +0200, Krzysztof Kozlowski wrote:
> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
> These are simple defines so they could be used in DTS but they will not
> have the same meaning:
> 1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
> 2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING
> 
> Correct the interrupt flags, assuming the author of the code wanted some
> logical behavior behind the name "ACTIVE_xxx", this is:
>   ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
>   ACTIVE_HIGH => IRQ_TYPE_LEVEL_HIGH
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
> ---
>  arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi      | 2 +-
>  arch/arm64/boot/dts/freescale/imx8mm-evk.dts              | 2 +-
>  arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts | 2 +-
>  arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi         | 2 +-
>  4 files changed, 4 insertions(+), 4 deletions(-)
> 
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
> index 620a124dfb5f..fdce665d7ac4 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-beacon-som.dtsi
> @@ -74,7 +74,7 @@
>  		reg = <0x4b>;
>  		pinctrl-0 = <&pinctrl_pmic>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <3 GPIO_ACTIVE_LOW>;
> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;

All rohm,bd71847 PMIC interrupts should be rather EDGE_FALLING.  Some of
the boards do not have external pull ups and most of the boards do not
configure internal pull up.  Level low would cause the interrupt line to
stay low all the time.

Best regards,
Krzysztof

>  		rohm,reset-snvs-powered;
>  
>  		regulators {
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> index 38134d201eef..609d73e19fee 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-evk.dts
> @@ -166,7 +166,7 @@
>  		reg = <0x4b>;
>  		pinctrl-0 = <&pinctrl_pmic>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <3 GPIO_ACTIVE_LOW>;
> +		interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
>  		rohm,reset-snvs-powered;
>  
>  		regulators {
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
> index 0bca737964d5..b84d94e10c26 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som-symphony.dts
> @@ -133,7 +133,7 @@
>  		pinctrl-names = "default";
>  		pinctrl-0 = <&pinctrl_captouch>;
>  		interrupt-parent = <&gpio5>;
> -		interrupts = <4 GPIO_ACTIVE_HIGH>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_HIGH>;
>  
>  		touchscreen-size-x = <800>;
>  		touchscreen-size-y = <480>;
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
> index c371cb34b3f7..49743d2f60c1 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-var-som.dtsi
> @@ -137,7 +137,7 @@
>  		reg = <0x4b>;
>  		pinctrl-0 = <&pinctrl_pmic>;
>  		interrupt-parent = <&gpio2>;
> -		interrupts = <8 GPIO_ACTIVE_LOW>;
> +		interrupts = <8 IRQ_TYPE_LEVEL_LOW>;
>  		rohm,reset-snvs-powered;
>  
>  		regulators {
> -- 
> 2.17.1
> 

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 1/8] ARM: dts: imx6qdl: Correct interrupt flags in examples

[Shawn Guo]

Add Tim who is the board owner.

On Tue, Sep 08, 2020 at 05:02:34PM +0200, Krzysztof Kozlowski wrote:
> GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
> These are simple defines so they could be used in DTS but they will not
> have the same meaning:
> 1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
> 2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING
> 
> Correct the interrupt flags, assuming the author of the code wanted some
> logical behavior behind the name "ACTIVE_xxx", this is:
>   ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

The subject prefix could be a bit more specific, like 'ARM: dts:
imx6qdl-gw5xxx'.  Also, I do not quite understand meaning of 'in
examples' in subject.

Shawn

> 
> ---
> 
> Not tested on HW.
> ---
>  arch/arm/boot/dts/imx6qdl-gw51xx.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw52xx.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw53xx.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw54xx.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw551x.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw552x.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw553x.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw560x.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw5903.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw5904.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw5907.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw5910.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw5912.dtsi | 3 ++-
>  arch/arm/boot/dts/imx6qdl-gw5913.dtsi | 3 ++-
>  14 files changed, 28 insertions(+), 14 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
> index 4d01c3300b97..3c04b5a4f3cb 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw51xx.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -152,7 +153,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
> index f6182a9d201c..736074f1c3ef 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw52xx.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -217,7 +218,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
> index a28e79463d0c..8072ed47c6bb 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw53xx.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -210,7 +211,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
> index 55f368e192c0..8c9bcdd39830 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw54xx.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/sound/fsl-imx-audmux.h>
>  
>  / {
> @@ -247,7 +248,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#address-cells = <1>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
> index 1516e2b0bcde..e5d803d023c8 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw551x.dtsi
> @@ -48,6 +48,7 @@
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/media/tda1997x.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  #include <dt-bindings/sound/fsl-imx-audmux.h>
>  
>  / {
> @@ -219,7 +220,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
> index 0da6e6f7482b..290a607fede9 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw552x.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -144,7 +145,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
> index faf9a3ba61b2..c15b9cc63bf8 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw553x.dtsi
> @@ -47,6 +47,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -180,7 +181,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
> index f68f9dada5b0..093a219a77ae 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw560x.dtsi
> @@ -47,6 +47,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -294,7 +295,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi b/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
> index fbe6c32bd756..e1c8dd233cab 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw5903.dtsi
> @@ -47,6 +47,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	chosen {
> @@ -235,7 +236,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
> index 23c6e4047621..3cd2e717c1da 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw5904.dtsi
> @@ -47,6 +47,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -257,7 +258,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
> index b1ff7c859c4d..21c68a55bcb9 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw5907.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -154,7 +155,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
> index 6c943a517ad7..ed4e22259959 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw5910.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -163,7 +164,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
> index 441d8ce97aa4..797f160249f7 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw5912.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -158,7 +159,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#address-cells = <1>;
> diff --git a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
> index d62a8da49367..4cd7d290f5b2 100644
> --- a/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
> +++ b/arch/arm/boot/dts/imx6qdl-gw5913.dtsi
> @@ -5,6 +5,7 @@
>  
>  #include <dt-bindings/gpio/gpio.h>
>  #include <dt-bindings/input/linux-event-codes.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>  
>  / {
>  	/* these are used by bootloader for disabling nodes */
> @@ -139,7 +140,7 @@
>  		compatible = "gw,gsc";
>  		reg = <0x20>;
>  		interrupt-parent = <&gpio1>;
> -		interrupts = <4 GPIO_ACTIVE_LOW>;
> +		interrupts = <4 IRQ_TYPE_LEVEL_LOW>;
>  		interrupt-controller;
>  		#interrupt-cells = <1>;
>  		#size-cells = <0>;
> -- 
> 2.17.1
> 

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 8/8] arm64: dts: imx8mm-var-som-symphony: Drop unused gpioledgrp

[Shawn Guo]

On Tue, Sep 08, 2020 at 05:02:41PM +0200, Krzysztof Kozlowski wrote:
> The gpioledgrp in iomux is not used, so it can be dropped.
> 
> Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>

Applied, thanks.

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip

Re: [PATCH 1/8] ARM: dts: imx6qdl: Correct interrupt flags in examples

[Krzysztof Kozlowski]

On Sun, 13 Sep 2020 at 04:32, Shawn Guo <shawnguo@kernel.org> wrote:
>
> Add Tim who is the board owner.
>
> On Tue, Sep 08, 2020 at 05:02:34PM +0200, Krzysztof Kozlowski wrote:
> > GPIO_ACTIVE_x flags are not correct in the context of interrupt flags.
> > These are simple defines so they could be used in DTS but they will not
> > have the same meaning:
> > 1. GPIO_ACTIVE_HIGH = 0 = IRQ_TYPE_NONE
> > 2. GPIO_ACTIVE_LOW  = 1 = IRQ_TYPE_EDGE_RISING
> >
> > Correct the interrupt flags, assuming the author of the code wanted some
> > logical behavior behind the name "ACTIVE_xxx", this is:
> >   ACTIVE_LOW  => IRQ_TYPE_LEVEL_LOW
> >
> > Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
>
> The subject prefix could be a bit more specific, like 'ARM: dts:
> imx6qdl-gw5xxx'.  Also, I do not quite understand meaning of 'in
> examples' in subject.

That's my copy-paste error. I'll resend with a proper subject.

Best regards,
Krzysztof

_______________________________________________
Linux-rockchip mailing list
Linux-rockchip@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-rockchip