From: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
To: matti.vaittinen@fi.rohmeurope.com, mazziesaccount@gmail.com
Cc: Lee Jones <lee.jones@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Mark Rutland <mark.rutland@arm.com>,
Liam Girdwood <lgirdwood@gmail.com>,
Mark Brown <broonie@kernel.org>,
Michael Turquette <mturquette@baylibre.com>,
Stephen Boyd <sboyd@kernel.org>,
Linus Walleij <linus.walleij@linaro.org>,
Bartosz Golaszewski <bgolaszewski@baylibre.com>,
Jacek Anaszewski <jacek.anaszewski@gmail.com>,
Pavel Machek <pavel@ucw.cz>, Dan Murphy <dmurphy@ti.com>,
Alessandro Zummo <a.zummo@towertech.it>,
Alexandre Belloni <alexandre.belloni@bootlin.com>,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org,
linux-clk@vger.kernel.org, linux-gpio@vger.kernel.org,
linux-leds@vger.kernel.org, linux-rtc@vger.kernel.org
Subject: [RFC PATCH 12/13] dt-bindings: mfd: Document ROHM BD71282 bindings
Date: Thu, 17 Oct 2019 12:55:26 +0300 [thread overview]
Message-ID: <05841ff33ea166bc6934456a492adc3c67a90670.1571302099.git.matti.vaittinen@fi.rohmeurope.com> (raw)
In-Reply-To: <cover.1571302099.git.matti.vaittinen@fi.rohmeurope.com>
ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
a real-time clock (RTC), 3 GPO/regulator control pins, HALL input pin
and a 32.768 kHz clock gate.
Document the dt bindings drivers are using.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
---
.../bindings/mfd/rohm,bd71828-pmic.txt | 180 ++++++++++++++++++
1 file changed, 180 insertions(+)
create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
new file mode 100644
index 000000000000..125efa9f3de0
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.txt
@@ -0,0 +1,180 @@
+* ROHM BD71828 Power Management Integrated Circuit bindings
+
+BD71828GW is a single-chip power management IC for battery-powered portable
+devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA single-cell
+linear charger. Also included is a Coulomb counter, a real-time clock (RTC),
+and a 32.768 kHz clock gate.
+
+Required properties:
+ - compatible : Should be "rohm,bd71828".
+ - reg : I2C slave address.
+ - interrupt-parent : Phandle to the parent interrupt controller.
+ - interrupts : The interrupt line the device is connected to.
+ - clocks : The parent clock connected to PMIC.
+ - #clock-cells : Should be 0.
+ - regulators : List of child nodes that specify the
+ regulators. Please see
+ ../regulator/rohm,bd71828-regulator.txt
+ - gpio-controller : To indicate BD71828 acts as a GPIO controller.
+ - #gpio-cells : Should be 2. The first cell is the pin number
+ and the second cell is used to specify flags.
+ See ../gpio/gpio.txt for more information.
+
+The BD71828 RUN state is divided into 4 configurable run-levels named RUN0,
+RUN1, RUN2 and RUN3. Bucks 1, 2, 6 and 7 can be either controlled individually
+via I2C, or some/all of them can be bound to run-levels and controlled as a
+group. If bucks are controlled individually these run-levels are ignored. See
+../regulator/rohm,bd71828-regulator.txt for how to define regulator voltages
+for run-levels. Run-levels can be changed by I2C or GPIO depending on PMIC's OTP
+configuration.
+
+Optional properties:
+- clock-output-names : Should contain name for output clock.
+- rohm,dvs-vsel-gpios : GPIOs used to control PMIC run-levels. Should
+ describe two GPIOs. (See run-level control in
+ data-sheet). If this property is omitted but
+ some bucks are marked to be controlled by
+ run-levels - then OTP option allowing
+ run-level control via I2C is assumed.
+- gpio-reserved-ranges : Usage of GPIO pins can be changed via OTP.
+ This property can be used to mark the pins
+ which should not be configured for GPIO.
+ Please see the ../gpio/gpio.txt for more
+ information.
+
+Example:
+
+ /* external oscillator node */
+ osc: oscillator {
+ compatible = "fixed-clock";
+ #clock-cells = <1>;
+ clock-frequency = <32768>;
+ clock-output-names = "osc";
+ };
+
+ pmic: pmic@4b {
+ compatible = "rohm,bd71828";
+ reg = <0x4b>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <29 GPIO_ACTIVE_LOW>;
+ clocks = <&osc 0>;
+ #clock-cells = <0>;
+ clock-output-names = "bd71828-32k-out";
+ gpio-controller;
+ #gpio-cells = <2>;
+ ngpios = <4>;
+ gpio-reserved-ranges = <0 1 2 1>;
+ gpio-line-names = "EPDEN";
+ rohm,dvs-vsel-gpios = <&gpio1 12 0>,
+ <&gpio1 13 0>;
+ regulators {
+ buck1: BUCK1 {
+ regulator-name = "buck1";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ buck2: BUCK2 {
+ regulator-name = "buck2";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ buck3: BUCK3 {
+ regulator-name = "buck3";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-boot-on;
+ };
+ buck4: BUCK4 {
+ regulator-name = "buck4";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+ buck5: BUCK5 {
+ regulator-name = "buck5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ buck6: BUCK6 {
+ regulator-name = "buck6";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ buck7: BUCK7 {
+ regulator-name = "buck7";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <2000000>;
+ regulator-ramp-delay = <2500>;
+ rohm,dvs-runlvl-ctrl;
+ rohm,dvs-runlevel0-voltage = <500000>;
+ rohm,dvs-runlevel1-voltage = <506250>;
+ rohm,dvs-runlevel2-voltage = <512500>;
+ rohm,dvs-runlevel3-voltage = <518750>;
+ regulator-boot-on;
+ };
+ ldo1: LDO1 {
+ regulator-name = "ldo1";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo2: LDO2 {
+ regulator-name = "ldo2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo3: LDO3 {
+ regulator-name = "ldo3";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo4: LDO4 {
+ regulator-name = "ldo4";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo5: LDO5 {
+ regulator-name = "ldo5";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ ldo6: LDO6 {
+ regulator-name = "ldo6";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-boot-on;
+ };
+ ldo7_reg: LDO7 {
+ regulator-name = "ldo7";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-boot-on;
+ };
+ };
+ };
--
2.21.0
--
Matti Vaittinen, Linux device drivers
ROHM Semiconductors, Finland SWDC
Kiviharjunlenkki 1E
90220 OULU
FINLAND
~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
Simon says - in Latin please.
~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
Thanks to Simon Glass for the translation =]
next prev parent reply other threads:[~2019-10-17 9:55 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2019-10-17 9:40 [RFC PATCH 00/13] Support ROHM BD71828 PMIC Matti Vaittinen
2019-10-17 9:41 ` [RFC PATCH 01/13] mfd: bd71828: Support ROHM BD71828 PMIC - core Matti Vaittinen
2019-10-17 9:42 ` [RFC PATCH 02/13] mfd: input: bd71828: Add power-key support Matti Vaittinen
2019-10-17 9:43 ` [RFC PATCH 03/13] clk: bd718x7: Support ROHM BD71828 clk block Matti Vaittinen
2019-10-17 9:44 ` [RFC PATCH 04/13] regulator: bd718x7: Split driver to common and bd718x7 specific parts Matti Vaittinen
2019-10-17 9:44 ` [RFC PATCH 05/13] regulator: bd71828: Basic support for ROHM bd71828 PMIC regulators Matti Vaittinen
2019-10-17 9:48 ` [RFC PATCH 06/13] regulator: bd71828: Add GPIO based run-level control for regulators Matti Vaittinen
2019-10-17 9:50 ` [RFC PATCH 07/13] regulator: bd71828: enhanced run-level support Matti Vaittinen
2019-10-17 9:51 ` [RFC PATCH 08/13] regulator: bd71828: Support in-kernel APIs to change run-level Matti Vaittinen
2019-10-17 9:52 ` [RFC PATCH 09/13] mfd: rtc: support RTC on ROHM BD71828 with BD70528 driver Matti Vaittinen
2019-10-17 10:12 ` Alexandre Belloni
2019-10-17 10:36 ` Vaittinen, Matti
2019-10-17 10:48 ` Alexandre Belloni
2019-10-21 5:29 ` Vaittinen, Matti
2019-10-23 10:27 ` Vaittinen, Matti
2019-10-29 13:50 ` Alexandre Belloni
2019-10-29 14:08 ` Vaittinen, Matti
2019-10-17 9:53 ` [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs Matti Vaittinen
2019-10-17 12:45 ` Bartosz Golaszewski
2019-10-21 7:00 ` Vaittinen, Matti
2019-10-21 14:36 ` Bartosz Golaszewski
2019-10-21 14:56 ` Vaittinen, Matti
2019-10-22 13:19 ` Vaittinen, Matti
2019-10-17 9:53 ` [RFC PATCH 11/13] led: bd71828: Support LED outputs on ROHM BD71828 PMIC Matti Vaittinen
2019-10-17 14:04 ` Dan Murphy
2019-10-17 14:28 ` Alexandre Belloni
2019-10-21 8:00 ` Vaittinen, Matti
2019-10-21 19:09 ` Jacek Anaszewski
2019-10-22 12:40 ` Vaittinen, Matti
2019-10-22 17:40 ` Jacek Anaszewski
2019-10-23 8:37 ` Vaittinen, Matti
2019-10-23 21:59 ` Jacek Anaszewski
2019-10-24 8:15 ` Vaittinen, Matti
2019-10-24 22:04 ` Jacek Anaszewski
2019-10-25 7:07 ` Vaittinen, Matti
2019-10-25 13:24 ` Rob Herring
2019-10-25 14:37 ` Vaittinen, Matti
2019-10-25 15:47 ` Rob Herring
2019-10-29 13:29 ` Vaittinen, Matti
2019-10-17 9:55 ` Matti Vaittinen [this message]
2019-10-17 14:18 ` [RFC PATCH 12/13] dt-bindings: mfd: Document ROHM BD71282 bindings Dan Murphy
2019-10-21 8:03 ` Vaittinen, Matti
2019-10-17 9:57 ` [RFC PATCH 13/13] dt-bindings: regulator: Document ROHM BD71282 regulator bindings Matti Vaittinen
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=05841ff33ea166bc6934456a492adc3c67a90670.1571302099.git.matti.vaittinen@fi.rohmeurope.com \
--to=matti.vaittinen@fi.rohmeurope.com \
--cc=a.zummo@towertech.it \
--cc=alexandre.belloni@bootlin.com \
--cc=bgolaszewski@baylibre.com \
--cc=broonie@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmurphy@ti.com \
--cc=jacek.anaszewski@gmail.com \
--cc=lee.jones@linaro.org \
--cc=lgirdwood@gmail.com \
--cc=linus.walleij@linaro.org \
--cc=linux-clk@vger.kernel.org \
--cc=linux-gpio@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=linux-rtc@vger.kernel.org \
--cc=mark.rutland@arm.com \
--cc=mazziesaccount@gmail.com \
--cc=mturquette@baylibre.com \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
--cc=sboyd@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).