linux-rtc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Javier Carrasco <javier.carrasco@wolfvision.net>
To: Alessandro Zummo <a.zummo@towertech.it>,
	 Alexandre Belloni <alexandre.belloni@bootlin.com>,
	 Rob Herring <robh+dt@kernel.org>,
	 Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	 Conor Dooley <conor+dt@kernel.org>
Cc: linux-rtc@vger.kernel.org, linux-kernel@vger.kernel.org,
	 devicetree@vger.kernel.org,
	 Javier Carrasco <javier.carrasco@wolfvision.net>
Subject: [PATCH 2/2] dt-bindings: rtc: nxp,pcf8563: add hiz-output property
Date: Wed, 25 Oct 2023 18:21:55 +0200	[thread overview]
Message-ID: <20231024-topic-pcf85363_hiz_output-v1-2-50908aff0e52@wolfvision.net> (raw)
In-Reply-To: <20231024-topic-pcf85363_hiz_output-v1-0-50908aff0e52@wolfvision.net>

The "hiz-output" property models the RTC output as a high-impedance
(hi-Z) output.

This property is optional and if it is not defined, the output will
either act as an output clock (default mode) or as an interrupt
depending on the configuration set by other properties.

Two modes are defined in case the high-impedance is used: "enabled" and
"sleep". The former disables the RTC output completely while the latter
keeps the RTC output disabled until the system enters in sleep mode.
This option is especially relevant if the output clock is used to feed a
PMU, a PMIC or any other device required to run when the rest of the
system is down. For the sake of completeness, a "disabled" mode has been
added, which acts as if the property was not defined.

Document "hiz-output" as a non-required property.

Signed-off-by: Javier Carrasco <javier.carrasco@wolfvision.net>
---
 Documentation/devicetree/bindings/rtc/nxp,pcf85363.yaml | 14 ++++++++++++++
 1 file changed, 14 insertions(+)

diff --git a/Documentation/devicetree/bindings/rtc/nxp,pcf85363.yaml b/Documentation/devicetree/bindings/rtc/nxp,pcf85363.yaml
index 52aa3e2091e9..4b27a9154191 100644
--- a/Documentation/devicetree/bindings/rtc/nxp,pcf85363.yaml
+++ b/Documentation/devicetree/bindings/rtc/nxp,pcf85363.yaml
@@ -36,6 +36,19 @@ properties:
     enum: [6000, 7000, 12500]
     default: 7000
 
+  hiz-output:
+    description:
+      Use enabled if the output should stay in high-impedance. This
+      mode will mask the output as an interrupt source.
+      Use sleep if the otuput should be only active in sleep mode.
+      This mode is compatible with any other output configuration.
+      The disabled value acts as if the property was not defined.
+    enum:
+      - enabled
+      - sleep
+      - disabled
+    default: disabled
+
   start-year: true
   wakeup-source: true
 
@@ -56,5 +69,6 @@ examples:
             reg = <0x51>;
             #clock-cells = <0>;
             quartz-load-femtofarads = <12500>;
+            hiz-output = "sleep";
         };
     };

-- 
2.39.2


  parent reply	other threads:[~2023-10-25 16:22 UTC|newest]

Thread overview: 13+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2023-10-25 16:21 [PATCH 0/2] rtc: pcf85363: add support for high-impedance output Javier Carrasco
2023-10-25 16:21 ` [PATCH 1/2] " Javier Carrasco
2023-10-25 16:21 ` Javier Carrasco [this message]
2023-10-25 22:23   ` [PATCH 2/2] dt-bindings: rtc: nxp,pcf8563: add hiz-output property Alexandre Belloni
2023-10-25 22:30     ` Javier Carrasco
2023-10-25 23:23       ` Javier Carrasco
2023-10-26  0:50         ` Alexandre Belloni
2023-10-26  9:41           ` Javier Carrasco
2023-10-26  9:56             ` Alexandre Belloni
2023-10-26 10:13               ` Javier Carrasco
2023-10-26 10:21                 ` Alexandre Belloni
2023-10-26 10:35                   ` Javier Carrasco
2024-01-30 21:34               ` Javier Carrasco

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=20231024-topic-pcf85363_hiz_output-v1-2-50908aff0e52@wolfvision.net \
    --to=javier.carrasco@wolfvision.net \
    --cc=a.zummo@towertech.it \
    --cc=alexandre.belloni@bootlin.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=robh+dt@kernel.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).