linux-rtc.vger.kernel.org archive mirror
 help / color / mirror / Atom feed
From: Josua Mayer <josua@solid-run.com>
To: Andrew Davis <afd@ti.com>, Nishanth Menon <nm@ti.com>,
	Vignesh Raghavendra <vigneshr@ti.com>,
	Tero Kristo <kristo@kernel.org>, Rob Herring <robh+dt@kernel.org>,
	Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
	Conor Dooley <conor+dt@kernel.org>,
	Alessandro Zummo <a.zummo@towertech.it>,
	Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Yazan Shhady <yazan.shhady@solid-run.com>,
	"linux-arm-kernel@lists.infradead.org"
	<linux-arm-kernel@lists.infradead.org>,
	"devicetree@vger.kernel.org" <devicetree@vger.kernel.org>,
	"linux-kernel@vger.kernel.org" <linux-kernel@vger.kernel.org>,
	"linux-rtc@vger.kernel.org" <linux-rtc@vger.kernel.org>
Subject: Re: [PATCH v4 4/5] arm64: dts: add description for solidrun am642 som and evaluation board
Date: Tue, 6 Feb 2024 14:41:05 +0000	[thread overview]
Message-ID: <a2cd8285-106c-480b-9fa3-4c58f60e9a55@solid-run.com> (raw)
In-Reply-To: <6b457759-9a2d-44a7-a1a4-7c7ac42aedae@ti.com>

Am 02.02.24 um 18:09 schrieb Andrew Davis:
> On 2/2/24 10:10 AM, Josua Mayer wrote:
>> Add description for the SolidRun AM642 SoM, and HummingBoard-T
>> evaluation board.
>>
>> The SoM features:
>> - 1x cpsw ethernet with phy
>> - 2x pru ethernet with phy
>> - eMMC
>> - spi flash (assembly option)
>>
>> Additionally microSD and usb-2.0 otg are included in the SoM
>> description as they are supported boot sources for the SOC boot-rom.
>>
>> The Carrier provides:
>> - 3x RJ45 connector
>> - 2x M.2 connector
>> - USB-2.0 Hub
>> - USB-A Connector
>> - LEDs
>> - 2x CAN transceiver
>> - 1x RS485 transceiver
>> - sensors
>>
>> The M.2 connectors support either USB-3.1 or PCI-E depending on status
>> of a mux. By default the mux is switched off.
>>
>> Signed-off-by: Josua Mayer <josua@solid-run.com>
>> ---
>>   arch/arm64/boot/dts/ti/Makefile                    |   1 +
>>   arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts | 292 ++++++++++
>>   arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi        | 592 +++++++++++++++++++++
>>   3 files changed, 885 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
>> index 77a347f9f47d..041c3b71155e 100644
>> --- a/arch/arm64/boot/dts/ti/Makefile
>> +++ b/arch/arm64/boot/dts/ti/Makefile
>> @@ -32,6 +32,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am62p5-sk.dtb
>>     # Boards with AM64x SoC
>>   dtb-$(CONFIG_ARCH_K3) += k3-am642-evm.dtb
>> +dtb-$(CONFIG_ARCH_K3) += k3-am642-hummingboard-t.dtb
>>   dtb-$(CONFIG_ARCH_K3) += k3-am642-phyboard-electra-rdk.dtb
>>   dtb-$(CONFIG_ARCH_K3) += k3-am642-sk.dtb
>>   dtb-$(CONFIG_ARCH_K3) += k3-am642-tqma64xxl-mbax4xxl.dtb
>> diff --git a/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts
>> new file mode 100644
>> index 000000000000..ebaf281e1e1e
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/ti/k3-am642-hummingboard-t.dts
>> @@ -0,0 +1,292 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2023 Josua Mayer <josua@solid-run.com>
>> + *
>> + * DTS for SolidRun AM642 HummingBoard-T,
>> + * running on Cortex A53.
>> + *
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/leds/common.h>
>> +#include <dt-bindings/phy/phy.h>
>> +
>> +#include "k3-am642.dtsi"
>> +#include "k3-am642-sr-som.dtsi"
>> +
>> +/ {
>> +    model = "SolidRun AM642 HummingBoard-T";
>> +    compatible = "solidrun,am642-hummingboard-t", "solidrun,am642-sr-som", "ti,am642";
>> +
>> +    aliases {
>> +        serial5 = &main_uart3;
>> +    };
>> +
>> +    leds {
>> +        compatible = "gpio-leds";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&leds_pins_default>;
>> +
>> +        /* D24 */
>> +        led1: led-1 {
>> +            label = "led1";
>> +            gpios = <&main_gpio0 29 GPIO_ACTIVE_HIGH>;
>> +            color = <LED_COLOR_ID_GREEN>;
>> +        };
>> +
>> +        /* D25 */
>> +        led2: led-2 {
>> +            label = "led2";
>> +            gpios = <&main_gpio0 30 GPIO_ACTIVE_HIGH>;
>> +            color = <LED_COLOR_ID_GREEN>;
>> +        };
>> +
>> +        /* D26 */
>> +        led3: led-3 {
>> +            label = "led3";
>> +            gpios = <&main_gpio0 33 GPIO_ACTIVE_HIGH>;
>> +            color = <LED_COLOR_ID_GREEN>;
>> +        };
>> +    };
>> +
>> +    regulator-m2-3v3 {
>> +        compatible = "regulator-fixed";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&regulator_pcie_3v3_pins_default>;
>> +        regulator-name = "m2-3v3";
>> +        regulator-min-microvolt = <3300000>;
>> +        regulator-max-microvolt = <3300000>;
>> +        gpio = <&main_gpio1 17 GPIO_ACTIVE_HIGH>;
>> +        enable-active-high;
>> +        regulator-always-on;
>> +    };
>> +
>> +    regulator-vpp-1v8 {
>> +        compatible = "regulator-fixed";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&regulator_vpp_1v8_pins_default>;
>> +        regulator-name = "vpp-1v8";
>> +        regulator-min-microvolt = <1800000>;
>> +        regulator-max-microvolt = <1800000>;
>> +        gpio = <&main_gpio1 78 GPIO_ACTIVE_HIGH>;
>> +        enable-active-high;
>> +    };
>> +
>> +    serdes_mux: mux-controller {
>> +        compatible = "gpio-mux";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&serdes_mux_pins_default>;
>> +        #mux-control-cells = <0>;
>> +        /*
>> +         * Mux has 2 IOs:
>> +         * - select: 0 = USB-3 (M2); 1 = PCIE (M1)
>> +         * - shutdown: 0 = active; 1 = disabled (high impedance)
>> +         */
>> +        mux-gpios = <&main_gpio1 40 GPIO_ACTIVE_HIGH>, <&main_gpio1 41 GPIO_ACTIVE_HIGH>;
>> +        /* default disabled */
>> +        idle-state = <2>;
>> +    };
>> +};
>> +
>> +&main_gpio0 {
>> +    m2-reset-hog {
>> +        gpio-hog;
>> +        gpios = <12 GPIO_ACTIVE_LOW>;
>> +        output-low; /* deasserted */
>> +        line-name = "m2-reset";
>> +    };
>> +
>> +    m1-m2-w-disable1-hog {
>> +        gpio-hog;
>> +        gpios = <32 GPIO_ACTIVE_LOW>;
>> +        output-low; /* deasserted */
>> +        line-name = "m1-m2-pcie-w-disable1";
>> +    };
>> +
>> +    m1-m2-w-disable2-hog {
>> +        gpio-hog;
>> +        gpios = <34 GPIO_ACTIVE_LOW>;
>> +        output-low; /* deasserted */
>> +        line-name = "m1-m2-pcie-w-disable2";
>> +    };
>> +};
>> +
>> +&main_gpio1 {
>> +    m1-pcie-clkreq0-hog {
>> +        gpio-hog;
>> +        gpios = <11 GPIO_ACTIVE_LOW>;
>> +        input;
>> +        line-name = "m1-pcie-clkreq0";
>> +    };
>> +
>> +    m2-pcie-clkreq-hog {
>> +        gpio-hog;
>> +        gpios = <35 GPIO_ACTIVE_LOW>;
>> +        input;
>> +        line-name = "m2-pcie-clkreq";
>> +    };
>> +};
>> +
>> +&main_i2c0 {
>> +    pinctrl-0 = <&main_i2c0_pins_default>, <&main_i2c0_int_pins_default>;
>> +
>> +    humidity-sensor@41 {
>> +        compatible = "ti,hdc2010";
>> +        reg = <0x41>;
>> +        interrupt-parent = <&main_gpio0>;
>> +        interrupts = <37 IRQ_TYPE_EDGE_FALLING>;
>> +    };
>> +
>> +    light-sensor@44 {
>> +        compatible = "ti,opt3001";
>> +        reg = <0x44>;
>> +        interrupt-parent = <&main_gpio0>;
>> +        interrupts = <37 IRQ_TYPE_EDGE_FALLING>;
>> +    };
>> +
>> +    /* charger@6a */
>> +};
>> +
>> +&main_i2c1 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_i2c1_pins_default>;
>> +    status = "okay";
>> +
>> +    rtc@69 {
>> +        compatible = "abracon,abx80x";
>> +        reg = <0x69>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&rtc_int_pins_default>;
>> +        abracon,tc-diode = "schottky";
>> +        abracon,tc-resistor = <3>;
>> +        interrupt-parent = <&main_gpio0>;
>> +        interrupts = <44 IRQ_TYPE_EDGE_FALLING>;
>> +    };
>> +};
>> +
>> +&main_mcan0 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_mcan0_pins_default>;
>> +    status = "okay";
>> +
>> +    can-transceiver {
>> +        max-bitrate = <8000000>;
>> +    };
>> +};
>> +
>> +&main_mcan1 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_mcan1_pins_default>;
>> +    status = "okay";
>> +
>> +    can-transceiver {
>> +        max-bitrate = <8000000>;
>> +    };
>> +};
>> +
>> +&main_pmx0 {
>> +    leds_pins_default: leds-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x0074, PIN_OUTPUT, 7)    /* GPMC0_AD14.GPIO0_29 */
>> +            AM64X_IOPAD(0x0078, PIN_OUTPUT, 7)    /* GPMC0_AD15.GPIO0_30 */
>> +            AM64X_IOPAD(0x0088, PIN_OUTPUT, 7)    /* GPMC0_OEn_REn.GPIO0_33 */
>> +        >;
>> +    };
>> +
>> +    main_i2c0_int_pins_default: main-i2c0-pins-int-default {
>> +        pinctrl-single,pins = <
>> +            /* external pull-up on Carrier */
>> +            AM64X_IOPAD(0x0098, PIN_INPUT, 7)    /* GPMC0_WAIT0.GPIO0_37 */
>> +        >;
>> +    };
>> +
>> +    main_i2c1_pins_default: main-i2c1-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* external pull-up on SoM */
>> +            AM64X_IOPAD(0x0268, PIN_INPUT, 0)    /* I2C1_SCL.I2C1_SCL */
>> +            AM64X_IOPAD(0x026c, PIN_INPUT, 0)    /* I2C1_SDA.I2C1_SDA */
>> +        >;
>> +    };
>> +
>> +    main_mcan0_pins_default: main-mcan0-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x0254, PIN_INPUT, 0)    /* MCAN0_RX.MCAN0_RX */
>> +            AM64X_IOPAD(0x0250, PIN_OUTPUT, 0)    /* MCAN0_TX.MCAN0_TX */
>> +        >;
>> +    };
>> +
>> +    main_mcan1_pins_default: main-mcan1-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x025c, PIN_INPUT, 0)    /* MCAN1_RX.MCAN1_RX */
>> +            AM64X_IOPAD(0x0258, PIN_OUTPUT, 0)    /* MCAN1_TX.MCAN1_TX */
>> +        >;
>> +    };
>> +
>> +    main_uart3_pins_default: main-uart3-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x016c, PIN_INPUT, 10)    /* PRG0_PRU0_GPO3.UART3_CTSn */
>> +            AM64X_IOPAD(0x0170, PIN_OUTPUT, 10)    /* PRG0_PRU0_GPO4.UART3_TXD */
>> +            AM64X_IOPAD(0x0174, PIN_OUTPUT, 10)    /* PRG0_PRU0_GPO5.UART3_RTSn */
>> +            AM64X_IOPAD(0x01ac, PIN_INPUT, 10)    /* PRG0_PRU0_GPO19.UART3_RXD */
>> +        >;
>> +    };
>> +
>> +    pcie0_pins_default: pcie0-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* connector M2 RESET */
>> +            AM64X_IOPAD(0x0030, PIN_OUTPUT, 7)    /* OSPI0_CSn1.GPIO0_12 */
>> +            /* connectors M1 & M2 W_DISABLE1 */
>> +            AM64X_IOPAD(0x0084, PIN_OUTPUT, 7)    /* GPMC0_ADVN_ALE.GPIO0_32 */
>> +            /* connectors M1 & M2 W_DISABLE2 */
>> +            AM64X_IOPAD(0x008c, PIN_OUTPUT, 7)    /* GPMC0_WEN.GPIO0_34 */
>> +            /* connectors M1 & M2 PERST0 (PCI Reset) */
>> +            AM64X_IOPAD(0x019c, PIN_OUTPUT, 7)    /* PRG0_PRU0_GPO15.GPIO1_15 */
>> +            /* connector M1 CLKREQ0 */
>> +            AM64X_IOPAD(0x018c, PIN_INPUT, 7)    /* PRG0_PRU0_GPO11.GPIO1_11 */
>> +            /* connector M2 CLKREQ0 */
>> +            AM64X_IOPAD(0x01ec, PIN_INPUT, 7)    /* PRG0_PRU1_GPO15.GPIO1_35 */
>> +        >;
>> +    };
>> +
>> +    regulator_pcie_3v3_pins_default: regulator-pcie-3v3-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x01a4, PIN_OUTPUT, 7)    /* PRG0_PRU0_GPO17.GPIO1_17 */
>> +        >;
>> +    };
>> +
>> +    regulator_vpp_1v8_pins_default: regulator-vpp-1v8-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x029c, PIN_OUTPUT, 7)    /* MMC1_SDWP.GPIO1_78 */
>> +        >;
>> +    };
>> +
>> +    rtc_int_pins_default: rtc-int-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* external pull-up on Carrier */
>> +            AM64X_IOPAD(0x00b4, PIN_INPUT, 7)    /* GPMC0_CSn3.GPIO0_44 */
>> +        >;
>> +    };
>> +
>> +    serdes_mux_pins_default: serdes-mux-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* SEL, 10k pull-down on carrier, 2.2k pullup on SoM */
>> +            AM64X_IOPAD(0x0200, PIN_OUTPUT, 7)    /* PRG0_MDIO0_MDIO.GPIO1_40 */
>> +            /* EN */
>> +            AM64X_IOPAD(0x0204, PIN_OUTPUT, 7)    /* PRG0_MDIO0_MDC.GPIO1_41 */
>> +        >;
>> +    };
>> +};
>> +
>> +&main_uart3 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_uart3_pins_default>;
>> +    uart-has-rtscts;
>> +    rs485-rts-active-low;
>> +    linux,rs485-enabled-at-boot-time;
>> +    status = "okay";
>> +};
>> +
>> +&usb0 {
>> +    dr_mode = "host";
>> +};
>> diff --git a/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi b/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
>> new file mode 100644
>> index 000000000000..83b73d433508
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/ti/k3-am642-sr-som.dtsi
>> @@ -0,0 +1,592 @@
>> +// SPDX-License-Identifier: GPL-2.0+
>> +/*
>> + * Copyright (C) 2023 Josua Mayer <josua@solid-run.com>
>> + *
>> + */
>> +
>> +#include <dt-bindings/net/ti-dp83869.h>
>> +
>> +/ {
>> +    model = "SolidRun AM642 SoM";
>> +    compatible = "solidrun,am642-sr-som", "ti,am642";
>> +
>> +    aliases {
>> +        ethernet0 = &cpsw_port1;
>> +        ethernet1 = &icssg1_emac0;
>> +        ethernet2 = &icssg1_emac1;
>> +        mmc0 = &sdhci0;
>> +        mmc1 = &sdhci1;
>> +        serial2 = &main_uart0;
>> +    };
>> +
>> +    chosen {
>> +        /* SoC default UART console */
>> +        stdout-path = "serial2:115200n8";
>> +    };
>> +
>> +    /* PRU Ethernet Controller */
>> +    ethernet {
>> +        compatible = "ti,am642-icssg-prueth";
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&pru_rgmii1_pins_default>, <&pru_rgmii2_pins_default>;
>> +
>> +        sram = <&oc_sram>;
>> +        ti,prus = <&pru1_0>, <&rtu1_0>, <&tx_pru1_0>, <&pru1_1>, <&rtu1_1>, <&tx_pru1_1>;
>> +        firmware-name = "ti-pruss/am65x-sr2-pru0-prueth-fw.elf",
>> +                "ti-pruss/am65x-sr2-rtu0-prueth-fw.elf",
>> +                "ti-pruss/am65x-sr2-txpru0-prueth-fw.elf",
>> +                "ti-pruss/am65x-sr2-pru1-prueth-fw.elf",
>> +                "ti-pruss/am65x-sr2-rtu1-prueth-fw.elf",
>> +                "ti-pruss/am65x-sr2-txpru1-prueth-fw.elf";
>> +
>> +        /* configure internal pinmux for mii mode */
>> +        ti,pruss-gp-mux-sel = <2>, <2>, <2>, <2>, <2>, <2>;
>> +
>> +        ti,mii-g-rt = <&icssg1_mii_g_rt>;
>> +        ti,mii-rt = <&icssg1_mii_rt>;
>> +        ti,iep = <&icssg1_iep0>, <&icssg1_iep1>;
>> +
>> +        /*
>> +         * Configure icssg interrupt controller to map pru-internal
>> +         * interrupts 8/9 via channels 0/1 to host interrupts 0/1.
>> +         *
>> +         * For details see interrupt controller documentation:
>> +         * Documentation/devicetree/bindings/interrupt-controller/ti,pruss-intc.yaml
>> +         */
>> +        interrupt-parent = <&icssg1_intc>;
>> +        interrupts = <24 0 2>, <25 1 3>;
>> +        interrupt-names = "tx_ts0", "tx_ts1";
>> +
>> +        dmas = <&main_pktdma 0xc200 15>, /* egress slice 0 */
>> +               <&main_pktdma 0xc201 15>, /* egress slice 0 */
>> +               <&main_pktdma 0xc202 15>, /* egress slice 0 */
>> +               <&main_pktdma 0xc203 15>, /* egress slice 0 */
>> +               <&main_pktdma 0xc204 15>, /* egress slice 1 */
>> +               <&main_pktdma 0xc205 15>, /* egress slice 1 */
>> +               <&main_pktdma 0xc206 15>, /* egress slice 1 */
>> +               <&main_pktdma 0xc207 15>, /* egress slice 1 */
>> +               <&main_pktdma 0x4200 15>, /* ingress slice 0 */
>> +               <&main_pktdma 0x4201 15>; /* ingress slice 1 */
>> +        dma-names = "tx0-0", "tx0-1", "tx0-2", "tx0-3",
>> +                "tx1-0", "tx1-1", "tx1-2", "tx1-3",
>> +                "rx0", "rx1";
>> +
>> +        ethernet-ports {
>> +            #address-cells = <1>;
>> +            #size-cells = <0>;
>> +
>> +            icssg1_emac0: port@0 {
>> +                reg = <0>;
>> +                ti,syscon-rgmii-delay = <&main_conf 0x4110>;
>> +                /* Filled in by bootloader */
>> +                local-mac-address = [00 00 00 00 00 00];
>> +                phy-handle = <&ethernet_phy2>;
>> +                phy-mode = "rgmii-id";
>> +            };
>> +
>> +            icssg1_emac1: port@1 {
>> +                reg = <1>;
>> +                ti,syscon-rgmii-delay = <&main_conf 0x4114>;
>> +                /* Filled in by bootloader */
>> +                local-mac-address = [00 00 00 00 00 00];
>> +                phy-handle = <&ethernet_phy1>;
>> +                phy-mode = "rgmii-id";
>> +            };
>> +        };
>> +    };
>> +
>> +    /* DDR16SS0:
>> +     * - Bank 1 @ 0x080000000-0x0FFFFFFFF: max. 2GB in 32-bit address space
>> +     * - Bank 2 @ 0x880000000-0x9FFFFFFFF: max. 6GB in 64-bit address space
>> +     */
>> +    memory@80000000 {
>> +        reg = <0x00000000 0x80000000 0x00000000 0x80000000>,
>> +              <0x00000008 0x80000000 0x00000001 0x80000000>;
>> +        device_type = "memory";
>> +    };
>> +
>> +    reserved-memory {
>> +        #address-cells = <2>;
>> +        #size-cells = <2>;
>> +        ranges;
>> +
>> +        secure_ddr: optee@9e800000 {
>> +            reg = <0x00 0x9e800000 0x00 0x01800000>; /* for OP-TEE */
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss0_core0_dma_memory_region: r5f-dma-memory@a0000000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa0000000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss0_core0_memory_region: r5f-memory@a0100000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa0100000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss0_core1_dma_memory_region: r5f-dma-memory@a1000000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa1000000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss0_core1_memory_region: r5f-memory@a1100000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa1100000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss1_core0_dma_memory_region: r5f-dma-memory@a2000000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa2000000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss1_core0_memory_region: r5f-memory@a2100000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa2100000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss1_core1_dma_memory_region: r5f-dma-memory@a3000000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa3000000 0x00 0x100000>;
>> +            no-map;
>> +        };
>> +
>> +        main_r5fss1_core1_memory_region: r5f-memory@a3100000 {
>> +            compatible = "shared-dma-pool";
>> +            reg = <0x00 0xa3100000 0x00 0xf00000>;
>> +            no-map;
>> +        };
>> +    };
>> +
>> +    vdd_mmc0: regulator-vdd-mmc0 {
>> +        compatible = "regulator-fixed";
>> +        regulator-name = "vdd-mmc0";
>> +        regulator-min-microvolt = <1800000>;
>> +        regulator-max-microvolt = <1800000>;
>> +        regulator-always-on;
>> +        regulator-boot-on;
>> +    };
>> +};
>> +
>> +&cpsw3g {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&rgmii1_pins_default>;
>> +};
>> +
>> +&cpsw3g_mdio {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&mdio0_pins_default>;
>> +    status = "okay";
>> +
>> +    ethernet_phy0: ethernet-phy@0 {
>> +        compatible = "ethernet-phy-id2000.a0f1";
>> +        reg = <0>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&ethernet_phy0_pins_default>;
>> +        ti,clk-output-sel = <DP83869_CLK_O_SEL_REF_CLK>;
>> +        ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
>> +        /*
>> +         * Disable interrupts because ISR never clears 0x0040
>> +         *
>> +         * interrupt-parent = <&main_gpio1>;
>> +         * interrupts = <70 IRQ_TYPE_LEVEL_LOW>;
>> +         */
>> +        /*
>> +         * Disable HW Reset because clock signal is daisy-chained
>> +         *
>> +         * reset-gpios = <&main_gpio0 84 GPIO_ACTIVE_LOW>;
>> +         * reset-assert-us = <1>;
>> +         * reset-deassert-us = <30>;
>> +         */
>> +    };
>> +};
>> +
>> +&cpsw_port1 {
>> +    phy-mode = "rgmii-id";
>> +    phy-handle = <&ethernet_phy0>;
>> +};
>> +
>> +&cpsw_port2 {
>> +    status = "disabled";
>> +};
>> +
>> +&icssg1_mdio {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&pru1_mdio0_pins_default>;
>> +    status = "okay";
>> +
>> +    ethernet_phy1: ethernet-phy@3 {
>> +        compatible = "ethernet-phy-id2000.a0f1";
>> +        reg = <3>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&ethernet_phy1_pins_default>;
>> +        ti,clk-output-sel = <DP83869_CLK_O_SEL_REF_CLK>;
>> +        ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
>> +        /*
>> +         * Disable interrupts because ISR never clears 0x0040
>> +         *
>> +         * interrupt-parent = <&main_gpio1>;
>> +         * interrupts = <70 IRQ_TYPE_LEVEL_LOW>;
>> +         */
>> +        /*
>> +         * Disable HW Reset because clock signal is daisy-chained
>> +         *
>> +         * reset-gpios = <&main_gpio0 20 GPIO_ACTIVE_LOW>;
>> +         * reset-assert-us = <1>;
>> +         * reset-deassert-us = <30>;
>> +         */
>> +    };
>> +
>> +    ethernet_phy2: ethernet-phy@f {
>> +        compatible = "ethernet-phy-id2000.a0f1";
>> +        reg = <0xf>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&ethernet_phy2_pins_default>;
>> +        ti,op-mode = <DP83869_RGMII_COPPER_ETHERNET>;
>> +        /*
>> +         * Disable interrupts because ISR never clears 0x0040
>> +         *
>> +         * interrupt-parent = <&main_gpio1>;
>> +         * interrupts = <70 IRQ_TYPE_LEVEL_LOW>;
>> +         */
>> +        /*
>> +         * Disable HW Reset because clock signal is daisy-chained
>> +         *
>> +         * reset-gpios = <&main_gpio0 52 GPIO_ACTIVE_LOW>;
>> +         * reset-assert-us = <1>;
>> +         * reset-deassert-us = <30>;
>> +         */
>> +    };
>> +};
>> +
>> +&mailbox0_cluster2 {
>> +    status = "okay";
>> +
>> +    mbox_main_r5fss0_core0: mbox-main-r5fss0-core0 {
>> +        ti,mbox-rx = <0 0 2>;
>> +        ti,mbox-tx = <1 0 2>;
>> +    };
>> +
>> +    mbox_main_r5fss0_core1: mbox-main-r5fss0-core1 {
>> +        ti,mbox-rx = <2 0 2>;
>> +        ti,mbox-tx = <3 0 2>;
>> +    };
>> +};
>> +
>> +&mailbox0_cluster4 {
>> +    status = "okay";
>> +
>> +    mbox_main_r5fss1_core0: mbox-main-r5fss1-core0 {
>> +        ti,mbox-rx = <0 0 2>;
>> +        ti,mbox-tx = <1 0 2>;
>> +    };
>> +
>> +    mbox_main_r5fss1_core1: mbox-main-r5fss1-core1 {
>> +        ti,mbox-rx = <2 0 2>;
>> +        ti,mbox-tx = <3 0 2>;
>> +    };
>> +};
>> +
>> +&main_i2c0 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_i2c0_pins_default>;
>> +    status = "okay";
>> +
>> +    som_eeprom: eeprom@50 {
>> +        compatible = "atmel,24c01";
>> +        reg = <0x50>;
>> +        pagesize = <8>;
>> +    };
>> +};
>> +
>> +&main_pmx0 {
>> +    /* hog global functions */
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&ethernet_phy_pins_default>;
>> +
>> +    ethernet_phy_pins_default: ethernet-phy-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* interrupt / power-down, external pull-up on SoM */
>> +            AM64X_IOPAD(0x0278, PIN_INPUT, 7)    /* EXTINTn.GPIO1_70 */
>> +        >;
>> +    };
>> +
>> +    ethernet_phy0_pins_default: ethernet-phy0-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* reset */
>> +            AM64X_IOPAD(0x0154, PIN_OUTPUT, 7)    /* PRG1_PRU1_GPO19.GPIO0_84 */
>> +            /* reference clock */
>> +            AM64X_IOPAD(0x0274, PIN_OUTPUT, 5)    /* EXT_REFCLK1.CLKOUT0 */
>> +        >;
>> +    };
>> +
>> +    ethernet_phy1_pins_default: ethernet-phy1-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* reset */
>> +            AM64X_IOPAD(0x0150, PIN_OUTPUT, 7)    /* PRG1_PRU1_GPO18.GPIO0_20 */
>> +            /* led0, external pull-down on SoM */
>> +            AM64X_IOPAD(0x0128, PIN_INPUT, 7)    /* PRG1_PRU1_GPO8.GPIO0_73 */
>> +            /* led1/rxer */
>> +            AM64X_IOPAD(0x011c, PIN_INPUT, 7)    /* PRG1_PRU1_GPO5.GPIO0_70 */
>> +        >;
>> +    };
>> +
>> +    ethernet_phy2_pins_default: ethernet-phy2-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* reset */
>> +            AM64X_IOPAD(0x00d4, PIN_OUTPUT, 7)    /* PRG1_PRU0_GPO7.GPIO0_52 */
>> +            /* led0, external pull-down on SoM */
>> +            AM64X_IOPAD(0x00d8, PIN_INPUT, 7)    /* PRG1_PRU0_GPO8.GPIO0_53 */
>> +            /* led1/rxer */
>> +            AM64X_IOPAD(0x00cc, PIN_INPUT, 7)    /* PRG1_PRU0_GPO5.GPIO0_50 */
>> +        >;
>> +    };
>> +
>> +    main_i2c0_pins_default: main-i2c0-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* external pull-up on SoM */
>> +            AM64X_IOPAD(0x0260, PIN_INPUT, 0)    /* I2C0_SCL.I2C0_SCL */
>> +            AM64X_IOPAD(0x0264, PIN_INPUT, 0)    /* I2C0_SDA.I2C0_SDA */
>> +        >;
>> +    };
>> +
>> +    /*
>> +     * main_mmc0_pins_default: main-mmc0-pins-default
>> +     *
>> +     * MMC0_CMD: no padconfig
>> +     * MMC0_CLK: no padconfig, external pull-up on SoM
>> +     * MMC0_DAT0: no padconfig
>> +     * MMC0_DAT1: no padconfig
>> +     * MMC0_DAT2: no padconfig
>> +     * MMC0_DAT3: no padconfig
>> +     * MMC0_DAT4: no padconfig
>> +     * MMC0_DAT5: no padconfig
>> +     * MMC0_DAT6: no padconfig
>> +     * MMC0_DAT7: no padconfig
>> +     * MMC0_DS: no padconfig, external pull-down on SoM
>> +     */
>> +
>> +    main_mmc1_pins_default: main-mmc1-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x0294, PIN_INPUT_PULLUP, 0)    /* (J19) MMC1_CMD */
>> +            AM64X_IOPAD(0x028c, PIN_INPUT, 0)        /* MMC1_CLK.MMC1_CLK */
>> +            AM64X_IOPAD(0x0288, PIN_INPUT_PULLUP, 0)    /* MMC1_DAT0.MMC1_DAT0 */
>> +            AM64X_IOPAD(0x0284, PIN_INPUT_PULLUP, 0)    /* MMC1_DAT1.MMC1_DAT1 */
>> +            AM64X_IOPAD(0x0280, PIN_INPUT_PULLUP, 0)    /* MMC1_DAT2.MMC1_DAT2 */
>> +            AM64X_IOPAD(0x027c, PIN_INPUT_PULLUP, 0)    /* MMC1_DAT3.MMC1_DAT3 */
>> +            /* external pull-down on SoM & Carrier */
>> +            AM64X_IOPAD(0x0298, PIN_INPUT_PULLUP, 0)    /* MMC1_SDCD.MMC1_SDCD */
>> +            AM64X_IOPAD(0x0290, PIN_INPUT, 0)        /* MMC1_CLKLB: clock loopback */
>> +        >;
>> +    };
>> +
>> +    main_uart0_pins_default: main-uart0-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x0230, PIN_INPUT, 0)        /* UART0_RXD.UART0_RXD */
>> +            AM64X_IOPAD(0x0234, PIN_OUTPUT, 0)        /* UART0_TXD.UART0_TXD */
>> +        >;
>> +    };
>> +
>> +    mdio0_pins_default: mdio0-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x01fc, PIN_OUTPUT, 4)        /* PRG0_PRU1_GPO19.MDIO0_MDC */
>> +            AM64X_IOPAD(0x01f8, PIN_INPUT, 4)        /* PRG0_PRU1_GPO18.MDIO0_MDIO */
>> +        >;
>> +    };
>> +
>> +    ospi0_pins_default: ospi0-pins-default {
>> +        pinctrl-single,pins = <
>> +            /* external pull-down on SoM */
>> +            AM64X_IOPAD(0x0000, PIN_OUTPUT, 0)        /* OSPI0_CLK.OSPI0_CLK */
>> +            AM64X_IOPAD(0x0008, PIN_OUTPUT, 0)        /* OSPI0_DQS.OSPI0_DQS */
>> +            /* external pull-up on SoM */
>> +            AM64X_IOPAD(0x002c, PIN_OUTPUT, 0)        /* OSPI0_CSn0.OSPI0_CSn0 */
>> +            AM64X_IOPAD(0x000c, PIN_INPUT, 0)        /* OSPI0_D0.OSPI0_D0 */
>> +            AM64X_IOPAD(0x0010, PIN_INPUT, 0)        /* OSPI0_D1.OSPI0_D1 */
>> +            AM64X_IOPAD(0x0014, PIN_INPUT, 0)        /* OSPI0_D2.OSPI0_D2 */
>> +            AM64X_IOPAD(0x0018, PIN_INPUT, 0)        /* OSPI0_D3.OSPI0_D3 */
>> +            AM64X_IOPAD(0x001c, PIN_INPUT, 0)        /* OSPI0_D4.OSPI0_D4 */
>> +            AM64X_IOPAD(0x0020, PIN_INPUT, 0)        /* OSPI0_D5.OSPI0_D5 */
>> +            AM64X_IOPAD(0x0024, PIN_INPUT, 0)        /* OSPI0_D6.OSPI0_D6 */
>> +            AM64X_IOPAD(0x0028, PIN_INPUT, 0)        /* OSPI0_D7.OSPI0_D7 */
>> +        >;
>> +    };
>> +
>> +    ospi0_flash0_pins_default: ospi0-flash0-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x0034, PIN_OUTPUT, 7)        /* OSPI0_CSn2.GPIO0_13 */
>> +            AM64X_IOPAD(0x0038, PIN_INPUT, 7)        /* OSPI0_CSn3.GPIO0_14 */
>> +        >;
>> +    };
>> +
>> +    pru1_mdio0_pins_default: pru1-mdio0-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x015c, PIN_OUTPUT, 0)        /* PRG1_MDIO0_MDC.PRG1_MDIO0_MDC */
>> +            AM64X_IOPAD(0x0158, PIN_INPUT, 0)        /* PRG1_MDIO0_MDIO.PRG1_MDIO0_MDIO */
>> +        >;
>> +    };
>> +
>> +    pru_rgmii1_pins_default: pru-rgmii1-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x00b8, PIN_INPUT, 2)        /* (Y7) PRG1_PRU0_GPO0.PRG1_RGMII1_RD0 */
>> +            AM64X_IOPAD(0x00bc, PIN_INPUT, 2)        /* (U8) PRG1_PRU0_GPO1.PRG1_RGMII1_RD1 */
>> +            AM64X_IOPAD(0x00c0, PIN_INPUT, 2)        /* (W8) PRG1_PRU0_GPO2.PRG1_RGMII1_RD2 */
>> +            AM64X_IOPAD(0x00c4, PIN_INPUT, 2)        /* (V8) PRG1_PRU0_GPO3.PRG1_RGMII1_RD3 */
>> +            AM64X_IOPAD(0x00d0, PIN_INPUT, 2)        /* (AA7) PRG1_PRU0_GPO6.PRG1_RGMII1_RXC */
>> +            AM64X_IOPAD(0x00c8, PIN_INPUT, 2)        /* (Y8) PRG1_PRU0_GPO4.PRG1_RGMII1_RX_CTL */
>> +            AM64X_IOPAD(0x00e4, PIN_OUTPUT, 2)        /* (AA8) PRG1_PRU0_GPO11.PRG1_RGMII1_TD0 */
>> +            AM64X_IOPAD(0x00e8, PIN_OUTPUT, 2)        /* (U9) PRG1_PRU0_GPO12.PRG1_RGMII1_TD1 */
>> +            AM64X_IOPAD(0x00ec, PIN_OUTPUT, 2)        /* (W9) PRG1_PRU0_GPO13.PRG1_RGMII1_TD2 */
>> +            AM64X_IOPAD(0x00f0, PIN_OUTPUT, 2)        /* (AA9) PRG1_PRU0_GPO14.PRG1_RGMII1_TD3 */
>> +            AM64X_IOPAD(0x00f8, PIN_INPUT, 2)        /* (V9) PRG1_PRU0_GPO16.PRG1_RGMII1_TXC */
>> +            AM64X_IOPAD(0x00f4, PIN_OUTPUT, 2)        /* (Y9) PRG1_PRU0_GPO15.PRG1_RGMII1_TX_CTL */
>> +        >;
>> +    };
>> +
>> +    pru_rgmii2_pins_default: pru-rgmii2-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x0108, PIN_INPUT, 2)        /* PRG1_PRU1_GPO0.RGMII2_RD0 */
>> +            AM64X_IOPAD(0x010c, PIN_INPUT, 2)        /* PRG1_PRU1_GPO1.RGMII2_RD1 */
>> +            AM64X_IOPAD(0x0110, PIN_INPUT, 2)        /* PRG1_PRU1_GPO2.RGMII2_RD2 */
>> +            AM64X_IOPAD(0x0114, PIN_INPUT, 2)        /* PRG1_PRU1_GPO3.RGMII2_RD3 */
>> +            AM64X_IOPAD(0x0120, PIN_INPUT, 2)        /* PRG1_PRU1_GPO6.RGMII2_RXC */
>> +            AM64X_IOPAD(0x0118, PIN_INPUT, 2)        /* PRG1_PRU1_GPO4.RGMII2_RX_CTL */
>> +            AM64X_IOPAD(0x0134, PIN_OUTPUT, 2)        /* PRG1_PRU1_GPO11.RGMII2_TD0 */
>> +            AM64X_IOPAD(0x0138, PIN_OUTPUT, 2)        /* PRG1_PRU1_GPO12.RGMII2_TD1 */
>> +            AM64X_IOPAD(0x013c, PIN_OUTPUT, 2)        /* PRG1_PRU1_GPO13.RGMII2_TD2 */
>> +            AM64X_IOPAD(0x0140, PIN_OUTPUT, 2)        /* PRG1_PRU1_GPO14.RGMII2_TD3 */
>> +            AM64X_IOPAD(0x0148, PIN_INPUT, 2)        /* PRG1_PRU1_GPO16.RGMII2_TXC */
>> +            AM64X_IOPAD(0x0144, PIN_OUTPUT, 2)        /* PRG1_PRU1_GPO15.RGMII2_TX_CTL */
>> +        >;
>> +    };
>> +
>> +    rgmii1_pins_default: rgmii1-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x01cc, PIN_INPUT, 4)        /* PRG0_PRU1_GPO7.RGMII1_RD0 */
>> +            AM64X_IOPAD(0x01d4, PIN_INPUT, 4)        /* PRG0_PRU1_GPO9.RGMII1_RD1 */
>> +            AM64X_IOPAD(0x01d8, PIN_INPUT, 4)        /* PRG0_PRU1_GPO10.RGMII1_RD2 */
>> +            AM64X_IOPAD(0x01f4, PIN_INPUT, 4)        /* PRG0_PRU1_GPO17.RGMII1_RD3 */
>> +            AM64X_IOPAD(0x0188, PIN_INPUT, 4)        /* PRG0_PRU0_GPO10.RGMII1_RXC */
>> +            AM64X_IOPAD(0x0184, PIN_INPUT, 4)        /* PRG0_PRU0_GPO9.RGMII1_RX_CTL */
>> +            AM64X_IOPAD(0x0124, PIN_OUTPUT, 4)        /* PRG1_PRU1_GPO7.RGMII1_TD0 */
>> +            AM64X_IOPAD(0x012c, PIN_OUTPUT, 4)        /* PRG1_PRU1_GPO9.RGMII1_TD1 */
>> +            AM64X_IOPAD(0x0130, PIN_OUTPUT, 4)        /* PRG1_PRU1_GPO10.RGMII1_TD2 */
>> +            AM64X_IOPAD(0x014c, PIN_OUTPUT, 4)        /* PRG1_PRU1_GPO17.RGMII1_TD3 */
>> +            AM64X_IOPAD(0x00e0, PIN_INPUT, 4)        /* PRG1_PRU0_GPO10.RGMII1_TXC */
>> +            AM64X_IOPAD(0x00dc, PIN_OUTPUT, 4)        /* PRG1_PRU0_GPO9.RGMII1_TX_CTL */
>> +        >;
>> +    };
>> +
>> +    usb0_pins_default: usb0-pins-default {
>> +        pinctrl-single,pins = <
>> +            AM64X_IOPAD(0x02a8, PIN_OUTPUT, 0)        /* USB0_DRVVBUS.USB0_DRVVBUS */
>> +        >;
>> +    };
>> +};
>> +
>> +&main_r5fss0_core0 {
>> +    mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core0>;
>> +    memory-region = <&main_r5fss0_core0_dma_memory_region>,
>> +            <&main_r5fss0_core0_memory_region>;
>> +};
>> +
>> +&main_r5fss0_core1 {
>> +    mboxes = <&mailbox0_cluster2 &mbox_main_r5fss0_core1>;
>> +    memory-region = <&main_r5fss0_core1_dma_memory_region>,
>> +            <&main_r5fss0_core1_memory_region>;
>> +};
>> +
>> +&main_r5fss1_core0 {
>> +    mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core0>;
>> +    memory-region = <&main_r5fss1_core0_dma_memory_region>,
>> +            <&main_r5fss1_core0_memory_region>;
>> +};
>> +
>> +&main_r5fss1_core1 {
>> +    mboxes = <&mailbox0_cluster4 &mbox_main_r5fss1_core1>;
>> +    memory-region = <&main_r5fss1_core1_dma_memory_region>,
>> +            <&main_r5fss1_core1_memory_region>;
>> +};
>> +
>> +/* SoC default UART console */
>> +&main_uart0 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_uart0_pins_default>;
>> +    status = "okay";
>> +};
>> +
>> +&ospi0 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&ospi0_pins_default>;
>> +    num-cs = <1>;
>> +    status = "okay";
>> +
>> +    flash@0 {
>> +        compatible = "jedec,spi-nor";
>> +        reg = <0>;
>> +        pinctrl-names = "default";
>> +        pinctrl-0 = <&ospi0_flash0_pins_default>;
>> +        spi-tx-bus-width = <8>;
>> +        spi-rx-bus-width = <8>;
>> +        spi-max-frequency = <200000000>;
>> +        cdns,tshsl-ns = <50>;
>> +        cdns,tsd2d-ns = <50>;
>> +        cdns,tchsh-ns = <4>;
>> +        cdns,tslch-ns = <4>;
>> +        cdns,read-delay = <0>;
>> +        interrupt-parent = <&main_gpio0>;
>> +        interrupts = <14 IRQ_TYPE_LEVEL_LOW>;
>> +        reset-gpios = <&main_gpio0 13 GPIO_ACTIVE_LOW>;
>> +    };
>> +};
>> +
>> +&sdhci0 {
>
> These sdhci* nodes are disabled by default
My full expectation in v0 was that (most) everything in
soc dtsi would have been disabled by default.

As per 6.7-rc7 k3-am64-main.dtsi did not disable sdhci nodes,
so this was fine, I had even removed my unnecessary
status = okay since v1 :(
(Now I can see how you spotted it, thanks!)

> , you might
> want to status = "okay" here.
Will re-add them just for sdhci nodes in v5.
> Rule of thumb is if you
> needed to add info to the node here in the board file
> it probably needs to be enabled here too.
>
> Otherwise LGTM,
>
> Reviewed-by: Andrew Davis <afd@ti.com>
>
>> +    /* mmc0 pins have no padconfig */
>> +    bus-width = <8>;
>> +    ti,driver-strength-ohm = <50>;
>> +    disable-wp;
>> +    non-removable;
>> +    cap-mmc-hw-reset;
>> +    no-sd;
>> +    /*
>> +     * MMC controller supports switching between 1.8V and 3.3V signalling.
>> +     * However MMC0 (unlike MMC1) does not integrate an LDO.
>> +     * Explicitly link a regulator node for indicating to the driver which
>> +     * voltages are actually usable.
>> +     */
>> +    vqmmc-supply = <&vdd_mmc0>;
>> +};
>> +
>> +/*
>> + * microSD is on carrier - however since SoC can boot from it,
>> + * configure it just in case.
>> + */
>> +&sdhci1 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&main_mmc1_pins_default>;
>> +    bus-width = <4>;
>> +    ti,driver-strength-ohm = <50>;
>> +    disable-wp;
>> +};
>> +
>> +/*
>> + * USB settings are a carrier choice - however since SoC can boot from it,
>> + * configure as USB-2.0 OTG here, keeping USB-3 serdes disabled.
>> + */
>> +&usb0 {
>> +    pinctrl-names = "default";
>> +    pinctrl-0 = <&usb0_pins_default>;
>> +    dr_mode = "otg";
>> +    maximum-speed = "high-speed";
>> +};
>> +
>> +&usbss0 {
>> +    ti,vbus-divider;
>> +    ti,usb2-only;
>> +};
>>

  reply	other threads:[~2024-02-06 14:41 UTC|newest]

Thread overview: 14+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2024-02-02 16:10 [PATCH v4 0/5] arm64: dts: add description for solidrun am642 som and hummingboard evb Josua Mayer
2024-02-02 16:10 ` [PATCH v4 1/5] dt-bindings: arm: ti: Add bindings for SolidRun AM642 HummingBoard-T Josua Mayer
2024-02-02 16:10 ` [PATCH v4 2/5] dt-bindings: rtc: abx80x: convert to yaml Josua Mayer
2024-02-02 17:35   ` Rob Herring
2024-02-03 15:08   ` Conor Dooley
2024-02-03 15:10     ` Conor Dooley
2024-02-06 14:44       ` Josua Mayer
2024-02-07 16:22         ` Conor Dooley
2024-02-11 14:57     ` Josua Mayer
2024-02-02 16:10 ` [PATCH v4 3/5] arm64: dts: ti: k3-am64-main: Add ICSSG IEP nodes Josua Mayer
2024-02-02 16:10 ` [PATCH v4 4/5] arm64: dts: add description for solidrun am642 som and evaluation board Josua Mayer
2024-02-02 17:09   ` Andrew Davis
2024-02-06 14:41     ` Josua Mayer [this message]
2024-02-02 16:10 ` [PATCH v4 5/5] arm64: dts: ti: hummingboard-t: add overlays for m.2 pci-e and usb-3 Josua Mayer

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=a2cd8285-106c-480b-9fa3-4c58f60e9a55@solid-run.com \
    --to=josua@solid-run.com \
    --cc=a.zummo@towertech.it \
    --cc=afd@ti.com \
    --cc=alexandre.belloni@bootlin.com \
    --cc=conor+dt@kernel.org \
    --cc=devicetree@vger.kernel.org \
    --cc=kristo@kernel.org \
    --cc=krzysztof.kozlowski+dt@linaro.org \
    --cc=linux-arm-kernel@lists.infradead.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-rtc@vger.kernel.org \
    --cc=nm@ti.com \
    --cc=robh+dt@kernel.org \
    --cc=vigneshr@ti.com \
    --cc=yazan.shhady@solid-run.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).