[PATCH v6 1/5] scsi: Adjust DBD setting in mode sense for caching mode page per LLD

[PATCH v6 1/5] scsi: Adjust DBD setting in mode sense for caching mode page per LLD

[Can Guo]

UFS JEDEC standards require DBD field to be set to 1 in mode sense command.
This patch allows LLD to define the setting of DBD if required.

Signed-off-by: Can Guo <cang@codeaurora.org>
---
 drivers/scsi/scsi_lib.c    | 2 ++
 include/scsi/scsi_device.h | 1 +
 2 files changed, 3 insertions(+)

diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c
index 5447738..3812e90 100644
--- a/drivers/scsi/scsi_lib.c
+++ b/drivers/scsi/scsi_lib.c
@@ -2108,6 +2108,8 @@ void scsi_exit_queue(void)
 
 	memset(data, 0, sizeof(*data));
 	memset(&cmd[0], 0, 12);
+
+	dbd = sdev->set_dbd_for_ms ? 8 : dbd;
 	cmd[1] = dbd & 0x18;	/* allows DBD and LLBA bits */
 	cmd[2] = modepage;
 
diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h
index 3ed836d..f8312a3 100644
--- a/include/scsi/scsi_device.h
+++ b/include/scsi/scsi_device.h
@@ -172,6 +172,7 @@ struct scsi_device {
 				     * because we did a bus reset. */
 	unsigned use_10_for_rw:1; /* first try 10-byte read / write */
 	unsigned use_10_for_ms:1; /* first try 10-byte mode sense/select */
+	unsigned set_dbd_for_ms:1; /* Set "DBD" field in mode sense */
 	unsigned no_report_opcodes:1;	/* no REPORT SUPPORTED OPERATION CODES */
 	unsigned no_write_same:1;	/* no WRITE SAME command */
 	unsigned use_16_for_rw:1; /* Use read/write(16) over read/write(10) */
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

RE: [PATCH v6 1/5] scsi: Adjust DBD setting in mode sense for caching mode page per LLD

[Avri Altman]

> 
> UFS JEDEC standards require DBD field to be set to 1 in mode sense command.
> This patch allows LLD to define the setting of DBD if required.
> 
> Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>

> ---
>  drivers/scsi/scsi_lib.c    | 2 ++
>  include/scsi/scsi_device.h | 1 +
>  2 files changed, 3 insertions(+)
> 
> diff --git a/drivers/scsi/scsi_lib.c b/drivers/scsi/scsi_lib.c index
> 5447738..3812e90 100644
> --- a/drivers/scsi/scsi_lib.c
> +++ b/drivers/scsi/scsi_lib.c
> @@ -2108,6 +2108,8 @@ void scsi_exit_queue(void)
> 
>         memset(data, 0, sizeof(*data));
>         memset(&cmd[0], 0, 12);
> +
> +       dbd = sdev->set_dbd_for_ms ? 8 : dbd;
>         cmd[1] = dbd & 0x18;    /* allows DBD and LLBA bits */
>         cmd[2] = modepage;
> 
> diff --git a/include/scsi/scsi_device.h b/include/scsi/scsi_device.h index
> 3ed836d..f8312a3 100644
> --- a/include/scsi/scsi_device.h
> +++ b/include/scsi/scsi_device.h
> @@ -172,6 +172,7 @@ struct scsi_device {
>                                      * because we did a bus reset. */
>         unsigned use_10_for_rw:1; /* first try 10-byte read / write */
>         unsigned use_10_for_ms:1; /* first try 10-byte mode sense/select */
> +       unsigned set_dbd_for_ms:1; /* Set "DBD" field in mode sense */
>         unsigned no_report_opcodes:1;   /* no REPORT SUPPORTED OPERATION
> CODES */
>         unsigned no_write_same:1;       /* no WRITE SAME command */
>         unsigned use_16_for_rw:1; /* Use read/write(16) over read/write(10) */
> --
> The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
> a Linux Foundation Collaborative Project

[PATCH v6 2/5] scsi: ufs: Use DBD setting in mode sense

[Can Guo]

UFS standards requires DBD field to be set to 1 in mode sense(10).

Some card vendors are more strict and check the DBD field, hence
respond with CHECK_CONDITION (Sense key set to ILLEGAL_REQUEST and
ASC set to INVALID FIELD IN CDB).
When host send mode sense for page caching, as a result of the
CHECK_CONDITION response, host assumes that the device doesn't support
the cache feature and doesn't send SYNCHRONIZE_CACHE commands to flush
the device cache. This can result in data corruption in case of sudden
power down, when there is data stored in the device cache.

This patch fixes the DBD field setting as required in UFS standards.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index c28c144..5484177 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -4596,6 +4596,9 @@ static int ufshcd_slave_alloc(struct scsi_device *sdev)
 	/* Mode sense(6) is not supported by UFS, so use Mode sense(10) */
 	sdev->use_10_for_ms = 1;
 
+	/* DBD field should be set to 1 in mode sense(10) */
+	sdev->set_dbd_for_ms = 1;
+
 	/* allow SCSI layer to restart the device in case of errors */
 	sdev->allow_restart = 1;
 
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v6 3/5] scsi: ufs: Release clock if DMA map fails

[Can Guo]

In queuecommand path, if DMA map fails, it bails out with clock held.
In this case, release the clock to keep its usage paired.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 5484177..9e44506 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -2480,6 +2480,7 @@ static int ufshcd_queuecommand(struct Scsi_Host *host, struct scsi_cmnd *cmd)
 	if (err) {
 		lrbp->cmd = NULL;
 		clear_bit_unlock(tag, &hba->lrb_in_use);
+		ufshcd_release(hba);
 		goto out;
 	}
 	/* Make sure descriptors are ready before ringing the doorbell */
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v6 4/5] scsi: ufs: Do not clear the DL layer timers

[Can Guo]

During power mode change, PACP_PWR_Req frame sends
PAPowerModeUserData parameters (and they are considered valid by device if
Flags[4] - UserDataValid bit is set in the same frame).
Currently we don't set these PAPowerModeUserData parameters and hardware
always sets UserDataValid bit which would clear all the DL layer timeout
values of the peer device after the power mode change.

This change sets the PAPowerModeUserData[0..5] to UniPro specification
recommended default values, in addition we are also setting the relevant
DME_LOCAL_* timer attributes as required by UFS HCI specification.

Signed-off-by: Can Guo <cang@codeaurora.org>
Reviewed-by: Avri Altman <avri.altman@wdc.com>
Reviewed-by: Bean Huo <beanhuo@micron.com>
---
 drivers/scsi/ufs/ufshcd.c | 20 ++++++++++++++++++++
 drivers/scsi/ufs/unipro.h | 11 +++++++++++
 2 files changed, 31 insertions(+)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 9e44506..086d359 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -4084,6 +4084,26 @@ static int ufshcd_change_power_mode(struct ufs_hba *hba,
 		ufshcd_dme_set(hba, UIC_ARG_MIB(PA_HSSERIES),
 						pwr_mode->hs_rate);
 
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA0),
+			DL_FC0ProtectionTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA1),
+			DL_TC0ReplayTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA2),
+			DL_AFC0ReqTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA3),
+			DL_FC1ProtectionTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA4),
+			DL_TC1ReplayTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(PA_PWRMODEUSERDATA5),
+			DL_AFC1ReqTimeOutVal_Default);
+
+	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalFC0ProtectionTimeOutVal),
+			DL_FC0ProtectionTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalTC0ReplayTimeOutVal),
+			DL_TC0ReplayTimeOutVal_Default);
+	ufshcd_dme_set(hba, UIC_ARG_MIB(DME_LocalAFC0ReqTimeOutVal),
+			DL_AFC0ReqTimeOutVal_Default);
+
 	ret = ufshcd_uic_change_pwr_mode(hba, pwr_mode->pwr_rx << 4
 			| pwr_mode->pwr_tx);
 
diff --git a/drivers/scsi/ufs/unipro.h b/drivers/scsi/ufs/unipro.h
index f539f87..3dc4d8b 100644
--- a/drivers/scsi/ufs/unipro.h
+++ b/drivers/scsi/ufs/unipro.h
@@ -161,6 +161,17 @@
 /* PHY Adapter Protocol Constants */
 #define PA_MAXDATALANES	4
 
+#define DL_FC0ProtectionTimeOutVal_Default	8191
+#define DL_TC0ReplayTimeOutVal_Default		65535
+#define DL_AFC0ReqTimeOutVal_Default		32767
+#define DL_FC1ProtectionTimeOutVal_Default	8191
+#define DL_TC1ReplayTimeOutVal_Default		65535
+#define DL_AFC1ReqTimeOutVal_Default		32767
+
+#define DME_LocalFC0ProtectionTimeOutVal	0xD041
+#define DME_LocalTC0ReplayTimeOutVal		0xD042
+#define DME_LocalAFC0ReqTimeOutVal		0xD043
+
 /* PA power modes */
 enum {
 	FAST_MODE	= 1,
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

[PATCH v6 5/5] scsi: ufs: Do not free irq in suspend

[Can Guo]

Since ufshcd irq resource is allocated with the device resource management
aware IRQ request implementation, we don't really need to free up irq
during suspend, disabling it during suspend and reenabling it during resume
should be good enough.

Signed-off-by: Can Guo <cang@codeaurora.org>
---
 drivers/scsi/ufs/ufshcd.c | 18 ++++--------------
 1 file changed, 4 insertions(+), 14 deletions(-)

diff --git a/drivers/scsi/ufs/ufshcd.c b/drivers/scsi/ufs/ufshcd.c
index 086d359..c449b68 100644
--- a/drivers/scsi/ufs/ufshcd.c
+++ b/drivers/scsi/ufs/ufshcd.c
@@ -266,26 +266,18 @@ static inline bool ufshcd_valid_tag(struct ufs_hba *hba, int tag)
 	return tag >= 0 && tag < hba->nutrs;
 }
 
-static inline int ufshcd_enable_irq(struct ufs_hba *hba)
+static inline void ufshcd_enable_irq(struct ufs_hba *hba)
 {
-	int ret = 0;
-
 	if (!hba->is_irq_enabled) {
-		ret = request_irq(hba->irq, ufshcd_intr, IRQF_SHARED, UFSHCD,
-				hba);
-		if (ret)
-			dev_err(hba->dev, "%s: request_irq failed, ret=%d\n",
-				__func__, ret);
+		enable_irq(hba->irq);
 		hba->is_irq_enabled = true;
 	}
-
-	return ret;
 }
 
 static inline void ufshcd_disable_irq(struct ufs_hba *hba)
 {
 	if (hba->is_irq_enabled) {
-		free_irq(hba->irq, hba);
+		disable_irq(hba->irq);
 		hba->is_irq_enabled = false;
 	}
 }
@@ -7930,9 +7922,7 @@ static int ufshcd_resume(struct ufs_hba *hba, enum ufs_pm_op pm_op)
 		goto out;
 
 	/* enable the host irq as host controller would be active soon */
-	ret = ufshcd_enable_irq(hba);
-	if (ret)
-		goto disable_irq_and_vops_clks;
+	ufshcd_enable_irq(hba);
 
 	ret = ufshcd_vreg_set_hpm(hba);
 	if (ret)
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

Re: [PATCH v6 5/5] scsi: ufs: Do not free irq in suspend

[Stanley Chu]

Hi Can,

On Thu, 2019-12-05 at 02:14 +0000, Can Guo wrote:
> Since ufshcd irq resource is allocated with the device resource management
> aware IRQ request implementation, we don't really need to free up irq
> during suspend, disabling it during suspend and reenabling it during resume
> should be good enough.

This is good in consideration of performance: enable_irq/disable_irq
performance is much better than request_irq/free_irq.

Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>