From: Jason Yan <yanaijie@huawei.com>
To: Jolly Shah <jollys@google.com>, <jejb@linux.ibm.com>,
<martin.petersen@oracle.com>, <john.garry@huawei.com>,
<a.darwish@linutronix.de>, <luojiaxing@huawei.com>,
<dan.carpenter@oracle.com>, <b.zolnierkie@samsung.com>
Cc: <linux-scsi@vger.kernel.org>, <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH] scsi: libsas: Reset num_scatter if libata mark qc as NODATA
Date: Wed, 17 Mar 2021 09:50:03 +0800 [thread overview]
Message-ID: <3a0626ae-327b-146f-5b2d-c58074c421a5@huawei.com> (raw)
In-Reply-To: <20210316193905.1673600-1-jollys@google.com>
在 2021/3/17 3:39, Jolly Shah 写道:
> When the cache_type for the scsi device is changed, the scsi layer
> issues a MODE_SELECT command. The caching mode details are communicated
> via a request buffer associated with the scsi command with data
> direction set as DMA_TO_DEVICE (scsi_mode_select). When this command
> reaches the libata layer, as a part of generic initial setup, libata
> layer sets up the scatterlist for the command using the scsi command
> (ata_scsi_qc_new). This command is then translated by the libata layer
> into ATA_CMD_SET_FEATURES (ata_scsi_mode_select_xlat). The libata layer
> treats this as a non data command (ata_mselect_caching), since it only
> needs an ata taskfile to pass the caching on/off information to the
> device. It does not need the scatterlist that has been setup, so it does
> not perform dma_map_sg on the scatterlist (ata_qc_issue). Unfortunately,
> when this command reaches the libsas layer(sas_ata_qc_issue), libsas
> layer sees it as a non data command with a scatterlist. It cannot
> extract the correct dma length, since the scatterlist has not been
> mapped with dma_map_sg for a DMA operation. When this partially
> constructed SAS task reaches pm80xx LLDD, it results in below warning.
>
> "pm80xx_chip_sata_req 6058: The sg list address
> start_addr=0x0000000000000000 data_len=0x0end_addr_high=0xffffffff
> end_addr_low=0xffffffff has crossed 4G boundary"
>
> This patch assigns appropriate value to num_sectors for ata non data
> commands.
>
> Signed-off-by: Jolly Shah <jollys@google.com>
> ---
> drivers/scsi/libsas/sas_ata.c | 6 ++++--
> 1 file changed, 4 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/scsi/libsas/sas_ata.c b/drivers/scsi/libsas/sas_ata.c
> index 024e5a550759..94ec08cebbaa 100644
> --- a/drivers/scsi/libsas/sas_ata.c
> +++ b/drivers/scsi/libsas/sas_ata.c
> @@ -209,10 +209,12 @@ static unsigned int sas_ata_qc_issue(struct ata_queued_cmd *qc)
> task->num_scatter = si;
> }
>
> - if (qc->tf.protocol == ATA_PROT_NODATA)
> + if (qc->tf.protocol == ATA_PROT_NODATA) {
> task->data_dir = DMA_NONE;
> - else
> + task->num_scatter = 0;
> + } else {
> task->data_dir = qc->dma_dir;
> + }
> task->scatter = qc->sg;
> task->ata_task.retry_count = 1;
> task->task_state_flags = SAS_TASK_STATE_PENDING;
>
Thanks for the patch. Except the warning, any functional errors?
The code looks good to me,
Reviewed-by: Jason Yan <yanaijie@huawei.com>
next prev parent reply other threads:[~2021-03-17 1:51 UTC|newest]
Thread overview: 7+ messages / expand[flat|nested] mbox.gz Atom feed top
2021-03-16 19:39 [PATCH] scsi: libsas: Reset num_scatter if libata mark qc as NODATA Jolly Shah
2021-03-17 1:50 ` Jason Yan [this message]
2021-03-17 17:11 ` Jolly Shah
2021-03-17 11:42 ` John Garry
2021-03-18 0:24 ` Jolly Shah
2021-03-18 16:17 ` John Garry
2021-03-18 23:06 ` Jolly Shah
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3a0626ae-327b-146f-5b2d-c58074c421a5@huawei.com \
--to=yanaijie@huawei.com \
--cc=a.darwish@linutronix.de \
--cc=b.zolnierkie@samsung.com \
--cc=dan.carpenter@oracle.com \
--cc=jejb@linux.ibm.com \
--cc=john.garry@huawei.com \
--cc=jollys@google.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-scsi@vger.kernel.org \
--cc=luojiaxing@huawei.com \
--cc=martin.petersen@oracle.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).