[PATCH] serial: msm_geni_serial_console : Add Earlycon support

* [PATCH] serial: msm_geni_serial_console : Add Earlycon support
@ 2020-04-29 17:19 Mukesh, Savaliya
  2020-04-29 17:38 ` Greg KH
  0 siblings, 1 reply; 4+ messages in thread
From: Mukesh, Savaliya @ 2020-04-29 17:19 UTC (permalink / raw)
  To: akashast, gregkh
  Cc: linux-serial, saravanak, sspatil, tkjos, Mukesh Kumar Savaliya

From: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>

This change enables earlyconsole support as static driver for geni
based UART. Kernel space UART console driver will be generic for
console and other usecases of UART.

Signed-off-by: Mukesh Kumar Savaliya <msavaliy@codeaurora.org>
---
 drivers/tty/serial/Kconfig                   |  15 +
 drivers/tty/serial/Makefile                  |   1 +
 drivers/tty/serial/msm_geni_serial_console.c | 525 +++++++++++++++++++
 3 files changed, 541 insertions(+)
 create mode 100644 drivers/tty/serial/msm_geni_serial_console.c

diff --git a/drivers/tty/serial/Kconfig b/drivers/tty/serial/Kconfig
index 0aea76cd67ff..ded19d80e696 100644
--- a/drivers/tty/serial/Kconfig
+++ b/drivers/tty/serial/Kconfig
@@ -956,6 +956,21 @@ config SERIAL_MSM_CONSOLE
 	select SERIAL_CORE_CONSOLE
 	select SERIAL_EARLYCON
 
+config SERIAL_MSM_GENI_HALF_SAMPLING
+	bool "Changes clock divider which impacts sampling rate for QUP HW ver greater than 2.5.0"
+	help
+	  Clock divider value should be doubled for QUP hardware version
+	  greater than 2.5.0.
+	  As earlycon can't have HW version awareness, decision is taken
+	  based on the configuration.
+
+config SERIAL_MSM_GENI_EARLY_CONSOLE
+	bool "MSM on-chip GENI HW based early console support"
+	select SERIAL_MSM_GENI_HALF_SAMPLING
+	help
+	  Serial early console driver for Qualcomm Technologies Inc's GENI
+	  based QUP hardware.
+
 config SERIAL_QCOM_GENI
 	tristate "QCOM on-chip GENI based serial port support"
 	depends on ARCH_QCOM || COMPILE_TEST
diff --git a/drivers/tty/serial/Makefile b/drivers/tty/serial/Makefile
index d056ee6cca33..9790ef2d802c 100644
--- a/drivers/tty/serial/Makefile
+++ b/drivers/tty/serial/Makefile
@@ -55,6 +55,7 @@ obj-$(CONFIG_SERIAL_VR41XX) += vr41xx_siu.o
 obj-$(CONFIG_SERIAL_ATMEL) += atmel_serial.o
 obj-$(CONFIG_SERIAL_UARTLITE) += uartlite.o
 obj-$(CONFIG_SERIAL_MSM) += msm_serial.o
+obj-$(SERIAL_MSM_GENI_EARLY_CONSOLE) += msm_geni_serial_console.o
 obj-$(CONFIG_SERIAL_QCOM_GENI) += qcom_geni_serial.o
 obj-$(CONFIG_SERIAL_OMAP) += omap-serial.o
 obj-$(CONFIG_SERIAL_ALTERA_UART) += altera_uart.o
diff --git a/drivers/tty/serial/msm_geni_serial_console.c b/drivers/tty/serial/msm_geni_serial_console.c
new file mode 100644
index 000000000000..3235611f7ef9
--- /dev/null
+++ b/drivers/tty/serial/msm_geni_serial_console.c
@@ -0,0 +1,525 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2020, The Linux Foundation. All rights reserved.
+ */
+#include <linux/console.h>
+#include <linux/delay.h>
+#include <linux/io.h>
+#include <linux/serial_core.h>
+
+#define SE_UART_TX_TRANS_CFG		(0x25C)
+#define SE_UART_TX_WORD_LEN		(0x268)
+#define SE_UART_TX_STOP_BIT_LEN		(0x26C)
+#define SE_UART_TX_TRANS_LEN		(0x270)
+#define SE_UART_TX_PARITY_CFG		(0x2A4)
+/* SE_UART_TRANS_CFG */
+#define UART_CTS_MASK		(BIT(1))
+/* UART M_CMD OP codes */
+#define UART_START_TX		(0x1)
+
+#define UART_OVERSAMPLING	(32)
+#define DEF_FIFO_DEPTH_WORDS	(16)
+#define DEF_TX_WM		(2)
+#define DEF_FIFO_WIDTH_BITS	(32)
+
+#define GENI_FORCE_DEFAULT_REG		(0x20)
+#define GENI_OUTPUT_CTRL		(0x24)
+#define GENI_CGC_CTRL			(0x28)
+#define GENI_SER_M_CLK_CFG		(0x48)
+#define GENI_FW_REVISION_RO		(0x68)
+
+#define SE_GENI_TX_PACKING_CFG0		(0x260)
+#define SE_GENI_TX_PACKING_CFG1		(0x264)
+#define SE_GENI_M_CMD0			(0x600)
+#define SE_GENI_M_CMD_CTRL_REG		(0x604)
+#define SE_GENI_M_IRQ_STATUS		(0x610)
+#define SE_GENI_M_IRQ_EN		(0x614)
+#define SE_GENI_M_IRQ_CLEAR		(0x618)
+#define SE_GENI_TX_FIFOn		(0x700)
+#define SE_GENI_TX_WATERMARK_REG	(0x80C)
+
+#define SE_IRQ_EN			(0xE1C)
+#define SE_HW_PARAM_0			(0xE24)
+#define SE_HW_PARAM_1			(0xE28)
+
+/* GENI_OUTPUT_CTRL fields */
+#define DEFAULT_IO_OUTPUT_CTRL_MSK	(GENMASK(6, 0))
+
+/* GENI_FORCE_DEFAULT_REG fields */
+#define FORCE_DEFAULT	(BIT(0))
+
+/* GENI_CGC_CTRL fields */
+#define CFG_AHB_CLK_CGC_ON		(BIT(0))
+#define CFG_AHB_WR_ACLK_CGC_ON		(BIT(1))
+#define DATA_AHB_CLK_CGC_ON		(BIT(2))
+#define SCLK_CGC_ON			(BIT(3))
+#define TX_CLK_CGC_ON			(BIT(4))
+#define RX_CLK_CGC_ON			(BIT(5))
+#define EXT_CLK_CGC_ON			(BIT(6))
+#define PROG_RAM_HCLK_OFF		(BIT(8))
+#define PROG_RAM_SCLK_OFF		(BIT(9))
+#define DEFAULT_CGC_EN			(GENMASK(6, 0))
+
+/* GENI_STATUS fields */
+#define M_GENI_CMD_ACTIVE		(BIT(0))
+
+/* GENI_SER_M_CLK_CFG/GENI_SER_S_CLK_CFG */
+#define SER_CLK_EN			(BIT(0))
+#define CLK_DIV_MSK			(GENMASK(15, 4))
+#define CLK_DIV_SHFT			(4)
+
+/* CLK_CTRL_RO fields */
+
+/* FIFO_IF_DISABLE_RO fields */
+#define FIFO_IF_DISABLE			(BIT(0))
+
+/* FW_REVISION_RO fields */
+#define FW_REV_PROTOCOL_MSK	(GENMASK(15, 8))
+#define FW_REV_PROTOCOL_SHFT	(8)
+#define FW_REV_VERSION_MSK	(GENMASK(7, 0))
+
+/* GENI_CLK_SEL fields */
+#define CLK_SEL_MSK		(GENMASK(2, 0))
+
+/* SE_GENI_DMA_MODE_EN */
+#define GENI_DMA_MODE_EN	(BIT(0))
+
+/* GENI_M_CMD0 fields */
+#define M_OPCODE_MSK		(GENMASK(31, 27))
+#define M_OPCODE_SHFT		(27)
+#define M_PARAMS_MSK		(GENMASK(26, 0))
+
+/* GENI_M_CMD_CTRL_REG */
+#define M_GENI_CMD_CANCEL	BIT(2)
+#define M_GENI_CMD_ABORT	BIT(1)
+#define M_GENI_DISABLE		BIT(0)
+
+/* GENI_M_IRQ_EN fields */
+#define M_CMD_DONE_EN		(BIT(0))
+#define M_CMD_OVERRUN_EN	(BIT(1))
+#define M_ILLEGAL_CMD_EN	(BIT(2))
+#define M_CMD_FAILURE_EN	(BIT(3))
+#define M_CMD_CANCEL_EN		(BIT(4))
+#define M_CMD_ABORT_EN		(BIT(5))
+#define M_TIMESTAMP_EN		(BIT(6))
+#define M_GP_SYNC_IRQ_0_EN	(BIT(8))
+#define M_IO_DATA_DEASSERT_EN	(BIT(22))
+#define M_IO_DATA_ASSERT_EN	(BIT(23))
+#define M_TX_FIFO_RD_ERR_EN	(BIT(28))
+#define M_TX_FIFO_WR_ERR_EN	(BIT(29))
+#define M_TX_FIFO_WATERMARK_EN	(BIT(30))
+#define M_SEC_IRQ_EN		(BIT(31))
+#define M_COMMON_GENI_M_IRQ_EN	(GENMASK(6, 1) | \
+				M_IO_DATA_DEASSERT_EN | \
+				M_IO_DATA_ASSERT_EN | M_TX_FIFO_RD_ERR_EN | \
+				M_TX_FIFO_WR_ERR_EN)
+
+
+/* GENI_TX_FIFO_STATUS fields */
+#define TX_FIFO_WC		(GENMASK(27, 0))
+
+/* SE_IRQ_EN fields */
+#define GENI_M_IRQ_EN		(BIT(2))
+
+#define UART_PROTOCOL	2
+#define GET_DEV_PORT(uport) \
+		container_of(uport, struct msm_geni_serial_earlycon_port, uport)
+
+static void geni_write_reg_earlycon(unsigned int value,
+						void __iomem *base, int offset)
+{
+	writel_relaxed(value, (base + offset));
+}
+
+static unsigned int geni_read_reg_earlycon(void __iomem *base, int offset)
+{
+	return readl_relaxed(base + offset);
+}
+
+static int get_se_proto_earlycon(void __iomem *base)
+{
+	int proto;
+
+	proto = ((geni_read_reg_earlycon(base, GENI_FW_REVISION_RO)
+			& FW_REV_PROTOCOL_MSK) >> FW_REV_PROTOCOL_SHFT);
+	return proto;
+}
+
+static void se_get_packing_config_earlycon(int bpw, int pack_words,
+	bool msb_to_lsb, unsigned long *cfg0, unsigned long *cfg1)
+{
+	u32 cfg[4] = {0};
+	int len;
+	int temp_bpw = bpw;
+	int idx_start = (msb_to_lsb ? (bpw - 1) : 0);
+	int idx = idx_start;
+	int idx_delta = (msb_to_lsb ? -BITS_PER_BYTE : BITS_PER_BYTE);
+	int ceil_bpw = ((bpw & (BITS_PER_BYTE - 1)) ?
+			((bpw & ~(BITS_PER_BYTE - 1)) + BITS_PER_BYTE) : bpw);
+	int iter = (ceil_bpw * pack_words) >> 3;
+	int i;
+
+	if (unlikely(iter <= 0 || iter > 4)) {
+		*cfg0 = 0;
+		*cfg1 = 0;
+		return;
+	}
+
+	for (i = 0; i < iter; i++) {
+		len = (temp_bpw < BITS_PER_BYTE) ?
+				(temp_bpw - 1) : BITS_PER_BYTE - 1;
+		cfg[i] = ((idx << 5) | (msb_to_lsb << 4) | (len << 1));
+		idx = ((temp_bpw - BITS_PER_BYTE) <= 0) ?
+				((i + 1) * BITS_PER_BYTE) + idx_start :
+				idx + idx_delta;
+		temp_bpw = ((temp_bpw - BITS_PER_BYTE) <= 0) ?
+				bpw : (temp_bpw - BITS_PER_BYTE);
+	}
+	cfg[iter - 1] |= 1;
+	*cfg0 = cfg[0] | (cfg[1] << 10);
+	*cfg1 = cfg[2] | (cfg[3] << 10);
+}
+
+static void se_geni_irq_en_earlycon(void __iomem *base)
+{
+	unsigned int common_geni_m_irq_en;
+
+	common_geni_m_irq_en = geni_read_reg_earlycon(base,
+							SE_GENI_M_IRQ_EN);
+	common_geni_m_irq_en |= M_COMMON_GENI_M_IRQ_EN;
+	geni_write_reg_earlycon(common_geni_m_irq_en, base, SE_GENI_M_IRQ_EN);
+}
+
+static void se_io_set_mode_earlycon(void __iomem *base)
+{
+	unsigned int io_mode;
+
+	io_mode = geni_read_reg_earlycon(base, SE_IRQ_EN);
+	io_mode |= (GENI_M_IRQ_EN);
+	geni_write_reg_earlycon(io_mode, base, SE_IRQ_EN);
+}
+
+static void se_io_init_earlycon(void __iomem *base)
+{
+	unsigned int io_op_ctrl;
+	unsigned int geni_cgc_ctrl;
+
+	geni_cgc_ctrl = geni_read_reg_earlycon(base, GENI_CGC_CTRL);
+	geni_cgc_ctrl |= DEFAULT_CGC_EN;
+	io_op_ctrl = DEFAULT_IO_OUTPUT_CTRL_MSK;
+	geni_write_reg_earlycon(geni_cgc_ctrl, base, GENI_CGC_CTRL);
+
+	geni_write_reg_earlycon(io_op_ctrl, base, GENI_OUTPUT_CTRL);
+	geni_write_reg_earlycon(FORCE_DEFAULT, base,
+							GENI_FORCE_DEFAULT_REG);
+}
+
+static void geni_se_select_fifo_mode_earlycon(void __iomem *base)
+{
+	unsigned int common_geni_m_irq_en;
+
+	geni_write_reg_earlycon(0xFFFFFFFF, base, SE_GENI_M_IRQ_CLEAR);
+	geni_write_reg_earlycon(0xFFFFFFFF, base, SE_IRQ_EN);
+
+	common_geni_m_irq_en = geni_read_reg_earlycon(base,
+							SE_GENI_M_IRQ_EN);
+	geni_write_reg_earlycon(common_geni_m_irq_en, base,
+							SE_GENI_M_IRQ_EN);
+}
+
+struct msm_geni_serial_earlycon_port {
+	struct uart_port uport;
+	unsigned int tx_fifo_depth;
+	unsigned int tx_fifo_width;
+	unsigned int tx_wm;
+	unsigned int xmit_size;
+	unsigned int cur_baud;
+};
+
+static int get_clk_cfg(unsigned long clk_freq, unsigned long *ser_clk)
+{
+	unsigned long root_freq[] = {7372800, 14745600, 19200000, 29491200,
+		32000000, 48000000, 64000000, 80000000, 96000000, 100000000,
+		102400000, 112000000, 120000000, 128000000};
+	int i;
+	int match = -1;
+
+	for (i = 0; i < ARRAY_SIZE(root_freq); i++) {
+		if (clk_freq > root_freq[i])
+			continue;
+
+		if (!(root_freq[i] % clk_freq)) {
+			match = i;
+			break;
+		}
+	}
+	if (match != -1)
+		*ser_clk = root_freq[match];
+
+	return match;
+}
+
+
+static int get_clk_div_rate(unsigned int baud, unsigned long *desired_clk_rate)
+{
+	unsigned long ser_clk;
+	int dfs_index;
+	int clk_div = 0;
+
+	*desired_clk_rate = baud * UART_OVERSAMPLING;
+	dfs_index = get_clk_cfg(*desired_clk_rate, &ser_clk);
+	if (dfs_index < 0) {
+		clk_div = -EINVAL;
+		goto exit_get_clk_div_rate;
+	}
+
+	clk_div = ser_clk / *desired_clk_rate;
+	*desired_clk_rate = ser_clk;
+exit_get_clk_div_rate:
+	return clk_div;
+}
+
+
+static void msm_geni_serial_wr_char(struct uart_port *uport, int ch)
+{
+	geni_write_reg_earlycon(ch, uport->membase, SE_GENI_TX_FIFOn);
+	/*
+	 * Ensure FIFO write clear goes through before
+	 * next iteration.
+	 */
+	mb();
+
+}
+
+static int msm_geni_serial_poll_bit(struct uart_port *uport,
+				int offset, int bit_field, bool set)
+{
+	int iter = 0;
+	unsigned int reg;
+	bool met = false;
+	struct msm_geni_serial_earlycon_port *port = NULL;
+	bool cond = false;
+	unsigned int baud = 115200;
+	unsigned int fifo_bits = DEF_FIFO_DEPTH_WORDS * DEF_FIFO_WIDTH_BITS;
+	unsigned long total_iter = 1000;
+
+
+	if (uport->private_data && !uart_console(uport)) {
+		port = GET_DEV_PORT(uport);
+		baud = (port->cur_baud ? port->cur_baud : 115200);
+		fifo_bits = port->tx_fifo_depth * port->tx_fifo_width;
+		/*
+		 * Total polling iterations based on FIFO worth of bytes to be
+		 * sent at current baud .Add a little fluff to the wait.
+		 */
+		total_iter = ((fifo_bits * USEC_PER_SEC) / baud) / 10;
+		total_iter += 50;
+	}
+
+	while (iter < total_iter) {
+		reg = geni_read_reg_earlycon(uport->membase, offset);
+		cond = reg & bit_field;
+		if (cond == set) {
+			met = true;
+			break;
+		}
+		udelay(10);
+		iter++;
+	}
+	return met;
+}
+
+static void msm_geni_serial_poll_cancel_tx(struct uart_port *uport)
+{
+	int done = 0;
+	unsigned int irq_clear = M_CMD_DONE_EN;
+
+	done = msm_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_CMD_DONE_EN, true);
+	if (!done) {
+		geni_write_reg_earlycon(M_GENI_CMD_ABORT, uport->membase,
+					SE_GENI_M_CMD_CTRL_REG);
+		irq_clear |= M_CMD_ABORT_EN;
+		msm_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+							M_CMD_ABORT_EN, true);
+	}
+	geni_write_reg_earlycon(irq_clear, uport->membase,
+				SE_GENI_M_IRQ_CLEAR);
+}
+
+static void msm_geni_serial_setup_tx(struct uart_port *uport,
+				unsigned int xmit_size)
+{
+	u32 m_cmd = 0;
+
+	geni_write_reg_earlycon(xmit_size, uport->membase,
+				SE_UART_TX_TRANS_LEN);
+	m_cmd |= (UART_START_TX << M_OPCODE_SHFT);
+	geni_write_reg_earlycon(m_cmd, uport->membase, SE_GENI_M_CMD0);
+	/*
+	 * Writes to enable the primary sequencer should go through before
+	 * exiting this function.
+	 */
+	mb();
+}
+
+
+static void
+__msm_geni_serial_console_write(struct uart_port *uport, const char *s,
+				unsigned int count)
+{
+	int new_line = 0;
+	int i;
+	int bytes_to_send = count;
+	int fifo_depth = DEF_FIFO_DEPTH_WORDS;
+	int tx_wm = DEF_TX_WM;
+
+	for (i = 0; i < count; i++) {
+		if (s[i] == '\n')
+			new_line++;
+	}
+
+	bytes_to_send += new_line;
+	geni_write_reg_earlycon(tx_wm, uport->membase,
+					SE_GENI_TX_WATERMARK_REG);
+	msm_geni_serial_setup_tx(uport, bytes_to_send);
+	i = 0;
+	while (i < count) {
+		u32 chars_to_write = 0;
+		u32 avail_fifo_bytes = (fifo_depth - tx_wm);
+		/*
+		 * If the WM bit never set, then the Tx state machine is not
+		 * in a valid state, so break, cancel/abort any existing
+		 * command. Unfortunately the current data being written is
+		 * lost.
+		 */
+		while (!msm_geni_serial_poll_bit(uport, SE_GENI_M_IRQ_STATUS,
+						M_TX_FIFO_WATERMARK_EN, true))
+			break;
+		chars_to_write = min((unsigned int)(count - i),
+							avail_fifo_bytes);
+		if ((chars_to_write << 1) > avail_fifo_bytes)
+			chars_to_write = (avail_fifo_bytes >> 1);
+		uart_console_write(uport, (s + i), chars_to_write,
+					msm_geni_serial_wr_char);
+		geni_write_reg_earlycon(M_TX_FIFO_WATERMARK_EN,
+			uport->membase, SE_GENI_M_IRQ_CLEAR);
+		/* Ensure this goes through before polling for WM IRQ again.*/
+		mb();
+		i += chars_to_write;
+	}
+	msm_geni_serial_poll_cancel_tx(uport);
+}
+
+
+static void
+msm_geni_serial_early_console_write(struct console *con, const char *s,
+			unsigned int n)
+{
+	struct earlycon_device *dev = con->data;
+
+	__msm_geni_serial_console_write(&dev->port, s, n);
+}
+
+static int __init
+msm_geni_serial_earlycon_setup(struct earlycon_device *dev,
+		const char *opt)
+{
+	struct uart_port *uport = &dev->port;
+	int ret = 0;
+	u32 tx_trans_cfg = 0;
+	u32 tx_parity_cfg = 0;
+	u32 rx_trans_cfg = 0;
+	u32 rx_parity_cfg = 0;
+	u32 stop_bit = 0;
+	u32 rx_stale = 0;
+	u32 bits_per_char = 0;
+	u32 s_clk_cfg = 0;
+	u32 baud = 115200;
+	int clk_div;
+	unsigned long clk_rate;
+	unsigned long cfg0, cfg1;
+
+	if (!uport->membase) {
+		ret = -ENOMEM;
+		goto exit_geni_serial_earlyconsetup;
+	}
+
+	if (get_se_proto_earlycon(uport->membase) != UART_PROTOCOL) {
+		ret = -ENXIO;
+		goto exit_geni_serial_earlyconsetup;
+	}
+
+	/*
+	 * Ignore Flow control.
+	 * Disable Tx Parity.
+	 * Don't check Parity during Rx.
+	 * Disable Rx Parity.
+	 * n = 8.
+	 * Stop bit = 0.
+	 * Stale timeout in bit-time (3 chars worth).
+	 */
+	tx_trans_cfg |= UART_CTS_MASK;
+	tx_parity_cfg = 0;
+	rx_trans_cfg = 0;
+	rx_parity_cfg = 0;
+	bits_per_char = 0x8;
+	stop_bit = 0;
+	rx_stale = 0x18;
+	clk_div = get_clk_div_rate(baud, &clk_rate);
+	if (clk_div <= 0) {
+		ret = -EINVAL;
+		goto exit_geni_serial_earlyconsetup;
+	}
+
+	if (IS_ENABLED(CONFIG_SERIAL_MSM_GENI_HALF_SAMPLING))
+		clk_div *= 2;
+
+	s_clk_cfg |= SER_CLK_EN;
+	s_clk_cfg |= (clk_div << CLK_DIV_SHFT);
+
+	/*
+	 * Make an unconditional cancel on the main sequencer to reset
+	 * it else we could end up in data loss scenarios.
+	 */
+	geni_write_reg_earlycon(0x21, uport->membase, GENI_SER_M_CLK_CFG);
+	geni_read_reg_earlycon(uport->membase, GENI_SER_M_CLK_CFG);
+
+	msm_geni_serial_poll_cancel_tx(uport);
+
+	se_get_packing_config_earlycon(8, 1, false, &cfg0, &cfg1);
+
+	se_io_init_earlycon(uport->membase);
+	se_io_set_mode_earlycon(uport->membase);
+	se_geni_irq_en_earlycon(uport->membase);
+
+	geni_se_select_fifo_mode_earlycon(uport->membase);
+	geni_write_reg_earlycon(cfg0, uport->membase,
+				SE_GENI_TX_PACKING_CFG0);
+	geni_write_reg_earlycon(cfg1, uport->membase,
+				SE_GENI_TX_PACKING_CFG1);
+	geni_write_reg_earlycon(tx_trans_cfg, uport->membase,
+				SE_UART_TX_TRANS_CFG);
+	geni_write_reg_earlycon(tx_parity_cfg, uport->membase,
+				SE_UART_TX_PARITY_CFG);
+	geni_write_reg_earlycon(bits_per_char, uport->membase,
+				SE_UART_TX_WORD_LEN);
+	geni_write_reg_earlycon(stop_bit, uport->membase,
+				SE_UART_TX_STOP_BIT_LEN);
+	geni_write_reg_earlycon(s_clk_cfg, uport->membase,
+				GENI_SER_M_CLK_CFG);
+	geni_read_reg_earlycon(uport->membase,
+				GENI_SER_M_CLK_CFG);
+
+	dev->con->write = msm_geni_serial_early_console_write;
+	dev->con->setup = NULL;
+	/*
+	 * Ensure that the early console setup completes before
+	 * returning.
+	 */
+	mb();
+exit_geni_serial_earlyconsetup:
+	return ret;
+}
+OF_EARLYCON_DECLARE(msm_geni_serial, "qcom,msm-geni-console",
+		msm_geni_serial_earlycon_setup);
-- 
The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

^ permalink raw reply related	[flat|nested] 4+ messages in thread